Fluida yang berasal dari manifold akan masuk ke separator melalui lubang inlet dan
selanjutnya menumbur inlet diverter. Disini terjadi perubahan momentum awal dalam pemisahan
cairan dan gas. Cairan yang berisi minyak dan air ini turun ke bagian bawah bejana separator
sedangkan gas akan bergerak naik ke atas melewati mist extractor dan keluar melalui outlet
gas.Untuk air akan keluar melalui outlet air dibagian bawah sedangkan minyak akan menumpuk
di bawah dan melewati weir untuk selanjutnya terakumulasi diruang khusus berisi minyak dan
keluar menuju minyak outlet. Faktor utama yang berpengaruh dalam pemisahan di separator
adalah berat jenis dari masing – masing fase. Dengan berat jenis yang dimiliki gas ringan
berkisar antara ...., maka didalam separator letaknya akan berada dibagian atas bejana separator.
Untuk air yang memiliki berat jenis paling berat diantara ketiga fase lainnya akan berada di
urutan paling bawah fluida dengan nilai .... dan minyak dengan berat jenis yang lebih ringan
daripada air akan akan terletak dibagian atas air dengan nilai .... Dengan aliran fluida yang terus
mengalir masuk ke dalam separator, membuat kapasitas penampungan untuk air dan minyak
akan menjadi penuh. Dengan penumpukan volume di separator akan berakibat pada tidak
maksimalnya pengeluaran fase di setiap lubang outletnya. Namun bila suatu kondisi dimana
tempat air terlalu sedikit maka minyak yang berada diatasnya akan keluar bersama air melalui
outlet air. Untuk itu dalam penanganannya, didalam separator terdapat suatu alat level interface
controll yang akan mengirimkan sinyal ke katup pembuangan air di bagian bawah, sehingga akan
terbuka secara otomatis. Dengan itu, maka akan memungkinkan jumlah air yang tepat untuk
dikeluarkan dari bejana sehingga antarmuka minyak dan air tetap dipertahankan pada ketinggian
desain separator. Antarmuka minyak dan air adalah batas kontak langsung antara permukaan
minyak dan air yang saling menimpa dibagian bawah bejana separator.
GAMBAR SEPARATOR 3 FASE DARI PDF BAHASA INGGRIS
Dari gambar diatas , tempat penampungan air dan minyak tidak sepenuhnya berada di seluruh
bagian bawah bejana hanya mencakup 2/3 dari panjang separator keseluruhaannya dan 1/3 dari
panjang separator merupakan ruangan tempat minyak bersih terakumulasi. Disinilah minyak
akan keluar melalui outlet minyak. Gas yang telah terpisah dari inlet diverter akan melewati mist
extractor, sebagai tempat penyaringan gas yang kemungkinan masih mengandung cairan.
Sehingga setelah melewatinya akan dihasilkan gas yang bersih menuju ke katup pengontrol
tekanan. Disini terjadi pengaturan tekanan konstan di dalam separator. Untuk penempatan gas
dalam separator yaitu 25% dari tinggi separator dan level antarmuka gas dan minyak dapat
berkisar 50%-75% dari diameter tinggi bejana separator yang tergantung pada ketinggian relatif
pemisahan gas dan cairan itu. Antarmuka gas dan minyak adalah batas kontak langsung antara
permukaan minyak tertinggi dengan gas yang berada dibagian tengah bejana separator.
Peralatan dalam separator:
- Inlet diverter, merupakan pemisahan tahap awal pada cairan dan gas. Ini menyebabkan
perubahan tiba – tiba dengan mengubah momentum kecepatan dan arah aliran dari fluida yang
- Mist Extractor, berfungsi untuk menyaring gas yang kemungkinan masih mengandung cairan
saat akan mengalir keluar menuju outlet gas. Cairan yang menempel di mist extractor akan
- Liquid Level Controll, digunakan untuk mengatur level fluida didalam separator, agar
dihasilkan ketinggian yang sesuai. LLC berisikan suatu pelampung yang berada diantarmuka
minyak dan gas, lalu mengirimkan sinyal secara otomatis ke penggerak katup untuk membuka
maupun menutup katup outlet minyak secara otomatis. Cairan yang keluar bisa sedikit maupun
banyak.
- Pressure Controll Valve merupakan suatu katup otomatis yang berada dalam aliran outlet gas
- Pressure Relief Valve merupkana suatu peralatan pengamanan yang secara otomatis akan
membuka lubang ventilasi di separator saat tekanan didalamnya telah melebihi batas keamanan.
The following is the working principle of the separator : Fluid coming from the manifold
will enter the separator through the inlet hole and then hit the inverter inlet. Here the initial
momentum changes in the separation of liquid and gas. This liquid containing oil and water
descends to the bottom of the separator vessel while the gas will move upward through the mist
extractor and out through the gas outlet. For water will come out through the bottom water outlet
while the oil will accumulate under and over the weir to further accumulate special room filled
with oil and out to the oil outlet. The main factor influencing the separation in the separator is the
specific gravity of each phase. With a specific gravity owned by light gas ranging between ...,
then in the separator the location will be at the top of the separator vessel. For water which has
the heaviest density among the three other phases it will be in the lowest order of fluid with a
value .... and oil with a specific gravity lighter than water will be located at the top of the water
with a value .... With fluid flow which continues to flow into the separator, making the holding
capacity for water and oil will be full. With the accumulation of volume in the separator will
result in a maximum phase outflow in each outlet hole. However, if there is a condition where
there is too little water, the oil above it will come out with water through the water outlet. For
that in handling, in the separator there is a level interface controller tool that will send a signal to
the drain valve at the bottom, so it will open automatically. By doing so, it will allow the right
amount of water to be removed from the vessel so that the oil and water interface is maintained
at the design height of the separator. The oil and water interface is the direct contact boundary
between the oil and water surfaces that overlap at the bottom of the separator vessel.
From the picture above, water and oil reservoirs are not completely located throughout
the bottom of the vessel covers only 2/3 of the total separator length and 1/3 of the length of the
separator is the room where clean oil accumulates. Here is oil will exit through the oil outlet. Gas
that has been separated from the inlet diverter will pass through the mist extractor, as a place for
filtering the gas that may still contain liquid. So that after passing through it will produce clean
gas to the pressure control valve. Here a constant pressure adjustment occurs inside the separator.
For gas placement in a separator that is 25% of the height of the separator and the interface level
of the gas and oil can range from 50% -75% of the diameter of the height of the separator vessel
which depends on the relative height of the separation of the gas and liquid. The gas and oil
interface is the direct contact limit between the highest oil surface and the gas in the center of the
separator vessel.
Equipment in a separator:
- Inlet diverter, which is the initial separation of liquids and gases. This causes a sudden change
by changing the velocity momentum and the direction of flow of fluid entering the separator.
- Mist Extractor, serves to filter out gases that may still contain liquid when it will flow out into
the gas outlet. The liquid that sticks to the mist extractor will fall down and accumulate with the
oil flow.
- Liquid Level Control, used to adjust the level of fluid in the separator, so that the resulting
height is appropriate. LLC contains a buoy which is in the oil and gas interface, then sends a
signal automatically to the valve drive to open or close the oil outlet valve automatically. The
- Pressure Control Valve is an automatic valve that is in the flow of the gas outlet with the aim to
separator when the pressure inside has exceeded the safety limit.