<1>: 1 CIRCLE
Command: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
Specify radius of circle or [Diameter]: 51
ommand: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
Specify radius of circle or [Diameter] <51.0000>: 30
Command: C
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
Specify radius of circle or [Diameter] <30.0000>: 18.5
Command:
Command:
Command: _trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects or <select all>:
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: ttr
Hasil
Command:
Command: _trim
Current settings: Projection=UCS, Edge=None
Select cutting edges ...
Select objects or <select all>:
Kemudian ubah pandangan pada auto cad dengan cara klik view pada toolbar:
Kemudian gambungkan garis satu dengan yang lain supaya menjadi satu kesatuan.
Command: region
Select objects: Specify opposite corner: 10 found
Select objects:
1 loop extracted.
1 Region created.
Extrude gambar
Command: _extrude
Current wire frame density: ISOLINES=4
Select objects to extrude: 1 found
Command: l
LINE Specify first point:
Specify next point or [Undo]:
Specify next point or [Undo]: *Cancel*
Kemudian ubah pandangannya lagi seperti langkah yang tadi yaitu klik view pada
toolbar kemudian klik back menjadi seperti gambar
ommand: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
Specify radius of circle or [Diameter] <2.0000>: 6.5
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
Specify radius of circle or [Diameter] <6.5000>: 2.5
[Fence/Crossing/Project/Edge/eRase/Undo]:
Command:
Command: _.erase 1 found
Command:
Command: _.erase 1 found
Kemudian ubah lagi tampilan dengan klik view kemudian pilih pandangan right,
gambar menjadi seperti gambar
Command: c
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]:
Specify radius of circle or [Diameter] <6.5000>: 6.5
Command: region
Select objects: 1 found
Select objects: 1 found, 2 total
Select objects: 1 found, 3 total
Select objects: 1 found, 4 total
Select objects:
1 loop extracted.
Command:
Command: _extrude
Current wire frame density: ISOLINES=4
Select objects to extrude: 1 found
Command: _extrude
Current wire frame density: ISOLINES=4
Select objects to extrude: 1 found
Command:
Command: _extrude
Current wire frame density: ISOLINES=41 found
Command: _extrude
Current wire frame density: ISOLINES=4
Select objects to extrude: 1 found
Command: _extrude
Current wire frame density: ISOLINES=4
Select objects to extrude: 1 found
Select objects:
Hasil
Kemudian buat irisan pada ujung sisi atas dan belakang dengan menggunakan
perintah Fillet
Command: _fillet
Current settings: Mode = TRIM, Radius = 5.0000
Select first object or [Undo/Polyline/Radius/Trim/Multiple]:
Enter fillet radius <5.0000>: r
Hasilnya
Pandangan SE Isometric