V) Transformer (30 mA, 120-700 V) 6 diodes (2000 PIV, 25 A) 6 dioda (2000 PIV, 25 A) 4 capacitors (10 Q F , 600 V DC) 4 kapasitor (10 Q F, 600 V DC) 4 capacitors (0.005 Q F , 2000 V DC) 4 kapasitor (0,005 Q F, 2000 V DC) 2 resistors (2 M ; , 1 W) 2 resistor (2 M ; 1 W) 6 resistors (25 k ; , 5 W) 6 resistor (25 k ; 5 W) Single-pole, single-throw switch (120 V, 5 A) Single-tiang, melemparkan tunggal beralih (120 V, 5 A) Power cord Kabel listrik Clip leads Klip mengarah Perforated phenolic board (12 12 inches) Fenolik perforasi papan (12 12 inci) Solderless spring terminals Solderless musim semi terminal DC milliammeter (0-20 mA) Milliammeter DC (0-20 mA) VOM Vom Capacitor shorting bar Kapasitor korslet bar Autotransformer Ototransformator Use the VOM to check all the diodes. Gunakan vom untuk memeriksa semua dioda. They should have a relatively low forward resistance and a very high reverse resistance. Mereka harus memiliki resistensi ke depan relatif rendah dan resistensi yang sebaliknya sangat tinggi. Check all resistors for proper values. Periksa semua nilai-nilai resistor yang tepat. Check capacitors for short circuits. Periksa kapasitor untuk sirkuit pendek. If the resistance of a capacitor does not rise to infinity within a short time, it is shorted or leaking. Jika resistansi kapasitor tidak naik hingga tak
terbatas dalam waktu singkat, itu adalah korsleting atau bocor. Discharge the capacitors after this step. Debit kapasitor setelah langkah ini. Lay out all diodes, capacitors, and resistors on the perforated phenolic board. Lay out semua dioda, kapasitor, dan resistor pada papan fenolik berlubang. Place solderless terminals at the appropriate positions on the board. Tempatkan terminal solderless di posisi yang tepat di papan tulis. Using the terminals, connect the components as shown in the diagram, Figure 31. Menggunakan terminal, menghubungkan komponen seperti yang ditunjukkan dalam diagram, Gambar 31. Be sure to connect the 10- Q F capacitors with their polarities as shown. Pastikan untuk menghubungkan 10 kapasitor F Q dengan polaritas mereka seperti yang ditunjukkan.
Fig. Gambar. 31 31 Helium-neon laser power supply Helium-neon laser daya pasokan Connect the laser tube and milliammeter to the power supply with clip leads. Hubungkan tabung laser dan milliammeter ke catu daya dengan memimpin klip. Make sure the anode and cathode of the tube are in the correct orientation. Pastikan anoda dan katoda tabung adalah pada orientasi yang benar. Connect the power cord, switch, and transformer. Hubungkan kabel daya, saklar, dan transformator. Check the entire circuit to ensure that it is correct. Periksa seluruh sirkuit untuk memastikan bahwa itu benar. Plug in the power cord and close the switch. Pasang kabel daya dan menutup saklar. Make sure not to touch any components in the power supply. Pastikan untuk tidak menyentuh komponen di power supply. If the tube does not come on within a few seconds, turn off and unplug the power supply, short the capacitors, and recheck the wiring. Jika tabung tidak datang pada dalam beberapa detik, matikan dan cabut catu daya, pendek kapasitor, dan memeriksa ulang kabel. When the tube is operating properly, check the current through the tube. Ketika tabung beroperasi dengan benar, periksa arus melalui tabung. It should be approximately 5 milliamperes. Ini harus sekitar 5 milliamperes. If this is significantly different, change the ballast resistance to give the proper value. Jika ini secara signifikan berbeda, mengubah perlawanan pemberat untuk memberikan nilai yang tepat. Remember always to turn the power supply off, unplug the power cord, and discharge the capacitors before touching any component. Ingatlah selalu untuk menghidupkan
catu daya, cabut kabel listrik, dan debit kapasitor sebelum menyentuh komponen apapun. With the laser off, attach the VOM across the cathode and anode terminals on the laser tube. Dengan laser off, pasang vom di terminal katoda dan anoda pada tabung laser. Set the voltage scale to 5000 V. Connect the power cord of the laser power supply, which has been plugged into a wall outlet. Menetapkan skala tegangan 5000 V. Hubungkan kabel daya dari catu daya laser, yang telah terpasang ke stopkontak. Turn on the power supply and slowly turn the knob on the autotransformer. Hidupkan power supply dan perlahan-lahan memutar tombolnya di ototransformator. Increase the voltage until the tube lights. Meningkatkan tegangan sampai lampu tabung. Observe the reading on the VOM at the moment at which the tube lights. Amati membaca di vom saat di mana lampu tabung. Continue increasing the input voltage in steps using the autotransformer. Lanjutkan meningkatkan tegangan input dalam langkah-langkah menggunakan ototransformator. At each step record the voltage and tube current. Pada setiap record langkah tegangan dan tabung saat ini. Continue increasing up to a maximum input voltage of 120 V. Terus meningkat sampai tegangan input maksimum 120 V. Turn the autotransformer to zero. Putar ototransformator ke nol. Turn the power supply off, unplug it, and short out the capacitors. Hidupkan power supply, cabut, dan pendek keluar kapasitor. Disassemble the power supply and return the components. Membongkar power supply dan mengembalikan komponen. Plot the current/voltage characteristic curve for the tube, using the data on current and voltage. Plot kurva karakteristik arus / tegangan untuk tabung, dengan menggunakan data arus dan tegangan. Identify the breakdown voltage and the negative-resistance portion of the curve. Identifikasi tegangan rusaknya dan bagian negatif-perlawanan dari kurva.