Keterangan CPL
CPMK 1.a Tugas
CPMK 1.b Tugas
CPMK 1.c Tugas
CPMK 2.a USS
CPMK 2.b USS
CPMK 2.c USS
CPMK 2.d USS
CPMK 4.a US
CPMK 4.b US
CPMK 4.c US
CPMK 4.d US
1. Sebuah batang berbentuk tabung seperti pada gambar, mempunyai tegangan tekan 41
kg/mm2, Diameter luar do = 11 cm, diameter dalam di = 6,5 cm. Tentukan berat beban
maksimal yang dapat ditahan tabung tersebut? Nilai maksimum : 20
KEMENTERIAN PENDIDIKAN DAN KEBUDAYAAN
UNIVERSITAS NEGERI SURABAYA
FAKULTAS TEKNIK
JURUSAN TEKNIK MESIN
Kampus Ketintang, Jalan Ketintang, Surabaya 60231
Telepon:+6231-8280009, Faksimil:+6231-8280796
Laman : http://mesin.ft.unesa.ac.id
F= ?
65
110
2. Batang seperti yang terdapat pada gambar, panjang 1,5 m, lebar 8 cm, tebal 4 cm. Salah satu
ujungnya dijepit dan ujung yang lain bebas. Bahan batang dari St 41, kalau di ujung yang
bebas dibebani, berapa beban maksimal yang dapat ditahan apabila garis kerja beban sejajar
sisi lebarnya? Nilai maksimum : 20
F=?
1500
St 41
3. Sebuah batang baja yang berdiameter 20 mm dengan panjang 0,55 meter, mengalami beba tarik
sebesar 30 kN, sehingga panjangnya menjadi 0,6 meter. Tentukan tegangan dan regangan normal
yang terjadi pada batang. Gambarkan penjelasan anda !. Nilai maksimum : 15
4. Sebuah poros berdiameter 60 mm mendapat pembebanan tekan (aksial) sebesar 220 KN dan momen
puntir 3kNm secara simultan. Tentukan tegangan utama dan tegangan geser maksimum yang
bekerja pada silinder tersebut (gambarkan kondisi tegangan secara 2D /3D opsional)!. Nilai
maksimum : 25
5. Tentukan letak titik berat pada penampang T tersebut terdiri dari dua persegi panjang
masing-masing dengan luas : Nilai maksimum : 20
A1 = 150 mm x 25 mm = 3.370 mm2
A2 = 100 mm x 25 mm = 2.500 mm2
12,5 100
25
?
100 Cg
25 150
( Akhmad Hafizh A.R, S.T., M.T ) ( Dany Iman Santoso, S.T., M.T)
Program Learning Outcomes (PLO) / Graduate Learning Outcomes (CPL) / Learning Outcomes (CP) for
Machine Element 1 course:
1. Knowledge of science and engineering
2. Design and develop solutions that pay attention to the environment and sustainability
3. Analyze the problem
• Course Outcome (CO) / Subject Learning Outcomes (CPMK):
1.a. Ability Identify specific facts about mathematics, science, and engineering
required for certain situations (What knowledge is required?)
1.b. Able to change real-world situations into models that are suitable for related subjects
1.c. Be able to demonstrate the proper use of specific facts of mathematics, science, and techniques to
derive performance behavior given certain inputs. 2.a. Able to design experimental plans
2.b. Able to obtain data about the appropriate variables in the field of Mechanical Engineering.
2.c. Be able to compare experimental data and results with appropriate theoretical models.
2.d. Be able to explain the observed differences between model and experiment.
4.a. Able to formulate problems and identify main problems / variables
4.b. Kemapuan recognizes several solutions that are needed.
4.c. Be able to analyze alternative solutions to engineering problems
4.d. Be able to present solutions to engineering problems
• Correlation between CPL and CPMK
Information CPL
CPMK 1.a Task
CPMK 1.b Task
CPMK 1.c Task
CPMK 2.a Mid Exam
CPMK 2.b Mid Exam
CPMK 2.c Mid Exam
CPMK 2.d Mid Exam
CPMK 4.a Final Exam
CPMK 4.b Final Exam
CPMK 4.c Final Exam
CPMK 4.d Final Exam
F= ?
65
KEMENTERIAN PENDIDIKAN DAN KEBUDAYAAN
UNIVERSITAS NEGERI SURABAYA
FAKULTAS TEKNIK
JURUSAN TEKNIK MESIN
Kampus Ketintang, Jalan Ketintang, Surabaya 60231
Telepon:+6231-8280009, Faksimil:+6231-8280796
Laman : http://mesin.ft.unesa.ac.id
110
2. Trunk as shown in the picture, 1.5 m long, 8 cm wide, 4 cm thick. One end is clamped and the
other end is free. The rod material of St 41, if at the free end is loaded, what is the maximum
load that can be withheld if the load working line is parallel to the width side? Maximum
score: 20
F=?
1500
St 41
3. A steel rod with a diameter of 20 mm with a length of 0.55 meters, experiences a tensile free of
30 kN, so that its length becomes 0.6 meters. Determine the normal stress and strain that occurs
in the rod. Describe your explanation! Maximum score: 15
4. A shaft with a diameter of 60 mm is subjected to a compressive (axial) loading of 220 KN and a
torsional moment of 3kNm simultaneously. Determine the principal stress and the maximum
shear stress acting on the cylinder (describe the stress conditions in optional 2D / 3D) !.
Maximum score: 25
5. Determine the location of the center of gravity on the cross-section T consisting of two
rectangles each with the following area: Maximum score: 20
A1 = 150 mm x 25 mm = 3.370 mm2
A2 = 100 mm x 25 mm = 2.500 mm2
12,5 100
25
?
100 Cg
25 150
( Akhmad Hafizh A.R, S.T., M.T ) ( Dany Iman Santoso, S.T., M.T)