Anda di halaman 1dari 52

BILL OF QUANTITY

PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13,028.00
Rev - 1
TOTAL HARGA (x Rp. 1.000,-)
NO URAIAN MATERIAL JASA
Rp. (x1000) US $ Rp. (x1000) US $

1 PEKERJAAN PERSIAPAN - - Rp -
2 ENGINEERING - - Rp -
3 PEKERJAAN SIPIL DAN STRUKTUR Rp - Rp -
4 PEKERJAAN MEKANIKAL DAN PEMIPAAN Rp US$ Rp -
5 PEKERJAAN ELEKTRIKAL Rp US$ Rp -
6 PEKERJAAN INSTRUMENT Rp US$ Rp -
7 PEKERJAAN PROCESS SAFETY Rp - Rp -
8 PEKERJAAN INSPEKSI, TESTING, & COMMISSIONING - - Rp -
9 TRAINING - - Rp -
10 PENYIAPAN DOKUMEN PENDUKUNG SERTIFIKASI SKPP & SKPI - - Rp -

TOTAL : 1 - 10 Rp - $ - Rp - -
KEUNTUNGAN DAN RESIKO (USD 5%, Rp. 8%) Rp - $ - Rp - -
TOTAL 1-10 + KEUNTUNGAN DAN RISIKO Rp - $ - Rp - -

TOTAL (US $) $ -
TOTAL (Rp) Rp -
GRAND TOTAL EKIVALEN (Rp) Rp -
PEMBULATAN Rp -
TERBILANG : ( .................................................................................................................. )

Page 0 of 34
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

1 PEKERJAAN PERSIAPAN & PEMULIHAN


Manpower Project Management (SDM EPC Contractor untuk Pengelolaan dan Pelaksanaan Proyek) 1 Ls - - Rp - - - Rp -
Pengukuran setting out & pembersihan lahan 1 Ls - - Rp - - - Rp -
Mob/demob material, alat, dan SDM 1 Ls - - Rp - - - Rp -
Direksi Keet & Gudang 1 Ls - - Rp - - - Rp -
Perijinan Konstruksi, sosialisasi dan keamanan 1 Ls - - Rp - - - Rp -
Air, Listrik kerja, dan kebutuhan lain terkait aktifitas - operasional proyek 1 Ls - - Rp - - - Rp -
WPS & PQR 1 Ls - - Rp - - - Rp -
Penyediaan Kendaraan Proyek (2 unit Kijang Innova terbaru) termasuk sopir, BBM, maintenance,asuransi A/R 20 bulan - - Rp - - - Rp -
Administrasi, laporan, telekomunikasi & dokumentasi 1 Ls - - Rp - - - Rp -
Perlengkapan dan peralatan terkait aspek HSE aktifitas konstruksi 1 Ls - - Rp - - - Rp -
Jalan akses ke lokasi proyek (dari jalan raya ke lahan proyek) 1 Ls - - Rp - - - Rp -
Rekondisi/pemulihan area kerja Depot eksisting menjadi seperti semula (pasca proyek) 1 Ls - - Rp - - - Rp -
Landscaping 300 m2 - - Rp - - - Rp -

Total 1 - - Rp -

2 ENGINEERING
Detail Engineering & As Built drawing 1 Ls - - Rp - - - Rp -

Total 2 - - Rp -

3 PEKERJAAN SIPIL DAN STRUKTUR

1 PILE FOUNDATION

LPG TANK FOUNDATION


Pile Foundation for :
Pile Cap 3,200.00 m Rp - Rp - Rp - Rp -

WATER SPRAY PIT FOUNDATION


Pile Foundation for :
Pit 24.00 m Rp - Rp - Rp - Rp -

PIPE SUPPORT FOUNDATION


Timber/Kayu Gelam Foundation for :
PS-002 176.00 m Rp - Rp - Rp - Rp -
PS-003A 312.00 m Rp - Rp - Rp - Rp -
PS-003B 168.00 m Rp - Rp - Rp - Rp -
PS-003C 1,376.00 m Rp - Rp - Rp - Rp -
PS-003D 64.00 m Rp - Rp - Rp - Rp -
PS-003E 320.00 m Rp - Rp - Rp - Rp -
PS-001A 160.00 m Rp - Rp - Rp - Rp -
PS-001B 128.00 m Rp - Rp - Rp - Rp -
PS-001C 24.00 m Rp - Rp - Rp - Rp -
PS-001D 80.00 m Rp - Rp - Rp - Rp -
PS-001E 128.00 m Rp - Rp - Rp - Rp -
PS-001F 48.00 m Rp - Rp - Rp - Rp -

PIPE BRIDGE FOUNDATION


Timber/Kayu Gelam Foundation for :
PS-001 120.00 m Rp - Rp - Rp - Rp -
PS-002 80.00 m Rp - Rp - Rp - Rp -

FILLING SHED FOUNDATION


Pile Foundation for :
Pile Cap 48.00 m Rp - Rp - Rp - Rp -

COOLING WATER TANK FOUNDATION


Pile Foundation for :
Pile Cap 5,170.00 m Rp - Rp - Rp - Rp -

WEIGHT BRIDGE SHELTER FOUNDATION


Page 2 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Pile Foundation for :


Pile Cap F1 72.00 m Rp - Rp - Rp - Rp -
Pile Foundation for :
Pile Cap F2 48.00 m Rp - Rp - Rp - Rp -

SECURITY POST FOUNDATIONT


Pile Foundation for :
Pile Cap 24.00 m Rp - Rp - Rp - Rp -

TRANSFORMER BUILDING FOUNDATION


Timber/Kayu Gelam Foundation for :
TYPE 1 64.00 m Rp - Rp - Rp - Rp -

FILLING PUMP SHELTER FOUNDATIONT


Pile Foundation for :
Pile Cap 24.00 m Rp - Rp - Rp - Rp -

FENCE & GATE FOUNDATION


Timber/Kayu Gelam Foundation for :
TYPE 1 8,280.00 m Rp - Rp - Rp - Rp -

WATER PUMP SHELTER FOUNDATION


Pile Foundation for :
Pile Cap 24.00 m Rp - Rp - Rp - Rp -

CONTROL ROOM FOUNDATION


Pile Foundation for :
Pile Cap 48.00 m Rp - Rp - Rp - Rp -

Pile specification:
- Minimum of compressive strength K600
- Pre-cast P.C pile (Type: Spun Pile)
- SP: Spun Pile

2 CIVIL WORK

LPG TANK FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 196.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 2,288.00 m2 - - Rp - - - Rp -
- Soil excavation 759.26 m3 - - Rp - - - Rp -
- Soil backfill and compaction 385.33 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 27.59 m3 Rp - Rp - Rp - Rp -
- Sand bedding 55.18 m3 Rp - Rp - Rp - Rp -

WATERPIT (3m W x 3m L x 2.5m D)


Civil works
Site preperation-install of bowplank and wood stiffener 24.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 16.00 m2 - - Rp - - - Rp -
- Soil excavation 53.24 m3 - - Rp - - - Rp -
- Soil backfill and compaction 17.69 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 0.88 m3 Rp - Rp - Rp - Rp -
- Sand bedding 1.76 m3 Rp - Rp - Rp - Rp -
Floor and Wall Finishes
- Concrete floor and wall waterproof coating 2mm – 3mm thickness 39.00 m2 Rp - Rp - Rp - Rp -
- Waterstop 12.80 m' Rp - Rp - Rp - Rp -

AIR COMPRESSOR UTILITY TANK FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 13.40 m' Rp - Rp - Rp - Rp -
- Site Clearing 5.16 m2 - - Rp - - - Rp -
- Soil excavation 8.57 m3 - - Rp - - - Rp -

Page 3 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- Soil backfill and compaction 6.76 m3 - - Rp - - - Rp -


Lean concrete & Sandbedding
- Lean Concrete 0.40 m3 Rp - Rp - Rp - Rp -
- Sand bedding 0.40 m3 Rp - Rp - Rp - Rp -

PIPE SUPPORT FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 2,438.40 m' Rp - Rp - Rp - Rp -
- Site Clearing 418.52 m2 - - Rp - - - Rp -
- Soil excavation 1,401.50 m3 - - Rp - - - Rp -
- Soil backfill and compaction 870.35 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 45.92 m3 Rp - Rp - Rp - Rp -
- Sand bedding 91.84 m3 Rp - Rp - Rp - Rp -

PIPE BRIDGE FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 127.60 m' Rp - Rp - Rp - Rp -
- Site Clearing 31.78 m2 - - Rp - - - Rp -
- Soil excavation 55.41 m3 - - Rp - - - Rp -
- Soil backfill and compaction 37.93 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 1.92 m3 Rp - Rp - Rp - Rp -
- Sand bedding 3.85 m3 Rp - Rp - Rp - Rp -

FILLING SHED FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 89.60 m' Rp - Rp - Rp - Rp -
- Site Clearing 5.12 m2 - - Rp - - - Rp -
- Soil excavation 35.42 m3 - - Rp - - - Rp -
- Soil backfill and compaction 27.10 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 1.14 m3 Rp - Rp - Rp - Rp -
- Sand bedding 2.29 m3 Rp - Rp - Rp - Rp -
Precast Concrete
- Drainase 300x300x100 32.00 m' Rp - Rp - Rp - Rp -

COOLING WATER TANK FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 87.96 m' Rp - Rp - Rp - Rp -
- Site Clearing 615.75 m2 - - Rp - - - Rp -
- Soil excavation 286.28 m3 - - Rp - - - Rp -
- Soil backfill and compaction 70.90 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 28.63 m3 Rp - Rp - Rp - Rp -
- Sand bedding 28.63 m3 Rp - Rp - Rp - Rp -

WATER PUMP SHELTER FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 38.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 72.00 m2 - - Rp - - - Rp -
- Soil excavation 55.80 m3 - - Rp - - - Rp -
- Soil backfill and compaction 22.37 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 4.94 m3 Rp - Rp - Rp - Rp -
- Sand bedding 9.87 m3 Rp - Rp - Rp - Rp -
Precast Concrete
- Drainase 300x300x100 34.00 m' Rp - Rp - Rp - Rp -

WEIGHT BRIDGE SHELTER FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 287.80 m' Rp - Rp - Rp - Rp -
- Site Clearing 115.12 m2 - - Rp - - - Rp -
- Soil excavation 295.71 m3 - - Rp - - - Rp -
- Soil backfill and compaction 235.05 m3 - - Rp - - - Rp -

Page 4 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Lean concrete & Sandbedding


- Lean Concrete 7.27 m3 Rp - Rp - Rp - Rp -
- Sand bedding 14.53 m3 Rp - Rp - Rp - Rp -
Precast Concrete
- Drainase 300x300x100 48.00 m' Rp - Rp - Rp - Rp -
Architecture & Finishing work Weighing Bridge Control Room
Brickwall, Plastering & Smooth surface plastering ('acian')
- Brickwall and thin bed mortar, 150mm thk. 50.00 m2 Rp - Rp - Rp - Rp -
- Plastering & smooth surface, 15mm thk 100.00 m2 Rp - Rp - Rp - Rp -
Floor and Wall Finishes
- Supply and install glazed ceramic tiles (or equal approved) sizes (400x400)mm 12.50 m2 Rp - Rp - Rp - Rp -
- Supply and install un-glazed ceramic tiles sizes (200x200)mm, on toilet room 1.50 m2 Rp - Rp - Rp - Rp -
Wall Finishes ceramic tile fixed w/mortar and tile grout
- Supply and install glazed ceramic tiles sizes (200x250) mm, hight: 2.1 m on wall rooms: toilet 10.50 m2 Rp - Rp - Rp - Rp -
Ceiling Finishes
Complete w/ metal suspension system, metal casing, ceiling joint and all necessary fixing
accessories as specified
- Acoustic Mineral Fiber Board size (600x600) mm or (600x1200) mm of 15mm th'k (min.) 14.00 m2 Rp - Rp - Rp - Rp -
- Moisture resistance mineral Fiber Board or 6mm th'k Glass Reinforced Concrete (GRC) board 22.00 m2 Rp - Rp - Rp - Rp -
Painting Works and Coating
- Prepare and apply one coat primer and two finishing coats of emulsion paint to interior surface 50.00 m2 Rp - Rp - Rp - Rp -
- Prepare and apply one coat primer and two finishing coats of watershield emulsion paint to exterior surface 96.00 m2 Rp - Rp - Rp - Rp -
- Prepare and apply waterproofing finishing coats to top of concrete roof surface 36.00 m2 Rp - Rp - Rp - Rp -
Doors and Windows...c/w all necessary fixing accessories.
Singgle door frame structure c/w all neccesarry fixing accessories
- Aluminium door, single leaf, swing opening, and size: 0.9 m W x 2.1m H. 1.00 Unit Rp - Rp - Rp - Rp -
PVC panel door and frame...c/w all necessary fixing accessories. 1.00 Unit Rp - Rp - Rp - Rp -
Windows and Aluminum frame finish…... Anodize c/w all necessary fixing accessories.
- Alum.frame and leaf window w/ opening 1 x ( 0.75W x 2.1H) m and fixed glass 6mm thk 5.00 Unit Rp - Rp - Rp - Rp -
Sanitary fixtures
Supply and install sanitary ex.TOTO Appliances complete including all necessary fitting accessories.
- Closet (seat type) 1.00 Set. Rp - Rp - Rp - Rp -
- Jet washer 1.00 Set. Rp - Rp - Rp - Rp -
Roof drain
- Downspout PVC pipe 4" dia. & fittings 14.00 m Rp - Rp - Rp - Rp -
- Strainer/ roof filter 4.00 Set. Rp - Rp - Rp - Rp -
Plumbing
- Conc. Septicktank and absorption system (3m L x 1.8m W x 2.150m H, Thickness : 150 mm) 1.00 Lot Rp - Rp - Rp - Rp -
- pipe 2" dia. & fittings 12.00 m Rp - Rp - Rp - Rp -
- pipe 4" dia. & fittings 8.00 m Rp - Rp - Rp - Rp -

ROAD & DRAINAGE FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 1,065.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 9,902.36 m2 - - Rp - - - Rp -
- Soil fill 2,970.71 m3 Rp - Rp - Rp - Rp -
- Soil compaction 9,902.36 m2 - - Rp - - - Rp -

Subgrade & Sub Base


- Lime Stone CBR 60% 1,980.47 m3 Rp - Rp - Rp - Rp -
- Subgrade CBR 6% 2,970.71 m3 Rp - Rp - Rp - Rp -
- Geotextile 8,992.77 m2 Rp - Rp - Rp - Rp -

FENCE & GATE FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 575.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 575.00 m2 - - Rp - - - Rp -
- Soil excavation 360.64 m3 - - Rp - - - Rp -
- Soil backfill and compaction 372.12 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 16.56 m3 Rp - Rp - Rp - Rp -
- Sand bedding 16.56 m3 Rp - Rp - Rp - Rp -
Precast Concrete
- Panel 2200x400x50 1,680.00 Nos Rp - Rp - Rp - Rp -

Page 5 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- Column 200x200 230.00 Nos Rp - Rp - Rp - Rp -

SECURITY POST FOUNDATION(3x4)


Civil works
Site preperation-install of bowplank and wood stiffener 18.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 20.00 m2 - - Rp - - - Rp -
- Soil excavation 24.12 m3 - - Rp - - - Rp -
- Soil backfill and compaction 10.10 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 2.30 m3 Rp - Rp - Rp - Rp -
- Sand bedding 4.61 m3 Rp - Rp - Rp - Rp -
Architecture & Finishing work
Brickwall, Plastering & Smooth surface plastering ('acian')
- Brickwall and thin bed mortar, size: (4mtr H x150mm thk) . 48.00 m2 Rp - Rp - Rp - Rp -
- Plastering & smooth surface, 15mm thk 96.00 m2 Rp - Rp - Rp - Rp -
Floor and Wall Finishes
- Supply and install glazed ceramic tiles (or equal approved) sizes (400x400)mm 9.75 m2 Rp - Rp - Rp - Rp -
- Supply and install un-glazed ceramic tiles sizes (200x200)mm, on toilet room 2.25 m2 Rp - Rp - Rp - Rp -
Wall Finishes ceramic tile fixed w/mortar and tile grout
- Supply and install glazed ceramic tiles sizes (200x250) mm, hight: 2.1 m on wall rooms: toilet 4.73 m2 Rp - Rp - Rp - Rp -
Ceiling Finishes
Complete w/ metal suspension system, metal casing, ceiling joint and all necessary fixing
accessories as specified
- Acoustic Mineral Fiber Board size (600x600) mm or (600x1200) mm of 15mm th'k (min.) 0.00 m2 Rp - Rp - Rp - Rp -
- Moisture resistance mineral Fiber Board or 6mm th'k Glass Reinforced Concrete (GRC) board 12.00 m2 Rp - Rp - Rp - Rp -
Painting Works and Coating
- Prepare and apply one coat primer and two finishing coats of emulsion paint to interior surface 48.00 m2 Rp - Rp - Rp - Rp -
- Prepare and apply one coat primer and two finishing coats of watershield emulsion paint to exterior surface 48.00 m2 Rp - Rp - Rp - Rp -
- Prepare and apply waterproofing finishing coats to top of concrete roof surface 20.00 m2 Rp - Rp - Rp - Rp -
Doors and Windows...c/w all necessary fixing accessories.
Glass door & aluminium frame ...c/w all necessary fixing accessories.

- Glass door & aluminium frame, single leaf, swing opening, size: 0.9 m W x 2.1 m H, location at: supervisor room (1), instrument panel 3.00 Unit Rp - Rp - Rp - Rp -
room (1), operator room (1).
PVC panel door and frame...c/w all necessary fixing accessories. 1.00 Unit Rp - Rp - Rp - Rp -
Windows and Aluminum frame finish…... Anodize c/w all necessary fixing accessories.
- Alum.frame and leaf window w/ opening 1 x ( 0.75W x 2.1H) m and fixed glass 6mm thk 4.00 Unit Rp - Rp - Rp - Rp -
- Alum.frame and leaf window w/ opening 6 x (0.9W x 0.9H) m and fixed glass 6mm thk 1.00 Unit Rp - Rp - Rp - Rp -
Sanitary fixtures
Supply and install sanitary ex….. Appliances complete including all necessary fitting accessories.
- Closet (seat type) 1.00 Set. Rp - Rp - Rp - Rp -
- Jet washer 1.00 Set. Rp - Rp - Rp - Rp -
Roof drain
- Downspout PVC pipe 4" dia. & fittings 24.00 m Rp - Rp - Rp - Rp -
- Strainer/ roof filter 8.00 Set. Rp - Rp - Rp - Rp -
Plumbing
- Septicktank and absorption system 1.00 Lot Rp - Rp - Rp - Rp -
- pipe 2" dia. & fittings 8.00 m Rp - Rp - Rp - Rp -
- pipe 4" dia. & fittings 8.00 m Rp - Rp - Rp - Rp -

TRANSFORMER BUILDING FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 56.20 m' Rp - Rp - Rp - Rp -
- Site Clearing 42.24 m2 - - Rp - - - Rp -
- Soil excavation 44.35 m3 - - Rp - - - Rp -
- Soil backfill and compaction 22.23 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 3.26 m3 Rp - Rp - Rp - Rp -
- Sand bedding 6.51 m3 Rp - Rp - Rp - Rp -
Precast Concrete
- Drainase 300x300x100 25.00 m' Rp - Rp - Rp - Rp -

GENSET FOUNDATION
Civil works
Site preperation-install of bowplank and wood stiffener 18.80 m' Rp - Rp - Rp - Rp -
- Site Clearing 5.97 m2 - - Rp - - - Rp -

Page 6 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- Soil excavation 7.04 m3 - - Rp - - - Rp -


- Soil backfill and compaction 2.09 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 0.35 m3 Rp - Rp - Rp - Rp -
- Sand bedding 0.71 m3 Rp - Rp - Rp - Rp -

FILLING PUMP SHELTER FOUNDATION


Civil works
Site preperation-install of bowplank and wood stiffener 66.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 69.00 m2 - - Rp - - - Rp -
- Soil excavation 50.94 m3 - - Rp - - - Rp -
- Soil backfill and compaction 21.34 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 4.44 m3 Rp - Rp - Rp - Rp -
- Sand bedding 8.89 m3 Rp - Rp - Rp - Rp -
Precast Concrete
- Drainase 300x300x100 32.00 m' Rp - Rp - Rp - Rp -

CONTROL ROOM
Civil works
Site preperation-install of bowplank and wood stiffener 28.00 m' Rp - Rp - Rp - Rp -
- Site Clearing 49.00 m2 - - Rp - - - Rp -
- Soil excavation 49.07 m3 - - Rp - - - Rp -
- Soil backfill and compaction 33.79 m3 - - Rp - - - Rp -
Lean concrete & Sandbedding
- Lean Concrete 5.49 m3 Rp - Rp - Rp - Rp -
- Sand bedding 10.98 m3 Rp - Rp - Rp - Rp -
Architecture & Finishing work
Brickwall, Plastering & Smooth surface plastering ('acian')
- Brickwall and thin bed mortar, size: (4mtr H x150mm thk) . 164.00 m2 Rp - Rp - Rp - Rp -
- Plastering & smooth surface, 15mm thk 328.00 m2 Rp - Rp - Rp - Rp -
Floor and Wall Finishes
- Supply and install glazed ceramic tiles (or equal approved) sizes (400x400)mm 129.07 m2 Rp - Rp - Rp - Rp -
- Supply and install un-glazed ceramic tiles sizes (200x200)mm, on toilet room 2.25 m2 Rp - Rp - Rp - Rp -
Wall Finishes ceramic tile fixed w/mortar and tile grout
- Supply and install glazed ceramic tiles sizes (200x250) mm, hight: 2.1 m on wall rooms: toilet 7.35 m2 Rp - Rp - Rp - Rp -
Raised Floor
- Instrument room 30.25 m2 Rp - Rp - Rp - Rp -
Ceiling Finishes
Complete w/ metal suspension system, metal casing, ceiling joint and all necessary fixing
accessories as specified
- Acoustic Mineral Fiber Board size (600x600) mm or (600x1200) mm of 15mm th'k (min.) 41.75 m2 Rp - Rp - Rp - Rp -
- Moisture resistance mineral Fiber Board or 6mm th'k Glass Reinforced Concrete (GRC) board 26.25 m2 Rp - Rp - Rp - Rp -
Painting Works and Coating
- Prepare and apply one coat primer and two finishing coats of emulsion paint to interior surface 164.00 m2 Rp - Rp - Rp - Rp -
- Prepare and apply one coat primer and two finishing coats of watershield emulsion paint to exterior surface 164.00 m2 Rp - Rp - Rp - Rp -
- Prepare and apply waterproofing finishing coats to top of concrete roof surface 64.00 m2 Rp - Rp - Rp - Rp -
Doors and Windows...c/w all necessary fixing accessories.
Glass door c/w all neccesarry fixing accessories
Tempered glass 12mm thk frameless c/w sticker/laminating , entrace door building or lobby area (1) 1.00 Unit Rp - Rp - Rp - Rp -
Tempered glass 12mm thk frameless c/w sticker/laminating (1 leaf) 1.00 Unit Rp - Rp - Rp - Rp -
Glass door, c/w aluminium frame, size: 0.9 m W x 2.1 m H, location at: batteryroom (1), UPS room (1), MCC room (1).
3.00 Unit Rp - Rp - Rp - Rp -
PVC panel door and frame...c/w all necessary fixing accessories. 1.00 Unit Rp - Rp - Rp - Rp -
Glass wall, windows w/w Aluminum frame Anodize c/w all necessary fixing accessories.
Dinding Kaca Tempered warna hijau bening c/w rangka dan aksesoris, t = 10mm 86.00 m2 Rp - Rp - Rp - Rp -
Sanitary fixtures
Supply and install sanitary ex TOTO Appliances complete including all necessary fitting accessories.
- Closet (seat type) 1.00 Set. Rp - Rp - Rp - Rp -
- Jet washer 1.00 Set. Rp - Rp - Rp - Rp -
Roof drain
- Downspout PVC pipe 4" dia. & fittings 68.00 m Rp - Rp - Rp - Rp -
- Strainer/ roof filter 8.00 Set. Rp - Rp - Rp - Rp -
Plumbing
- Conc. Septicktank and absorption system (3m L x 1.8m W x 2.150m H, Thickness : 150 mm) 1.00 Lot Rp - Rp - Rp - Rp -

Page 7 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- pipe 2" dia. & fittings 12.00 m Rp - Rp - Rp - Rp -


- pipe 4" dia. & fittings 8.00 m Rp - Rp - Rp - Rp -

Galian dan Timbunan Tanah Pemasangan Kabel (600 W, 500 D)


Galian Tanah 720.00 m3 Rp - Rp - Rp - Rp -
Sand Fill 500 mm Thick 450.00 m3 Rp - Rp - Rp - Rp -
Pasir Split 300 mm Thick 270.00 m3 Rp - Rp - Rp - Rp -

Modification Panel Room 1.00 Ls Rp - Rp - Rp - Rp -


Concrete Cable Trench Including Cover 300 W 300 H 8000 L 100 thick
Demolish some existing brickwall +(15 m2)
Brick Awal c/w plastering smooth surfaces (15 m2)
Sand fill (1 m3)
Lean Concrete (0.5 m3)
Ceramic floor (10 m2)
Plafon (10 m2)
Roof ekstension (12.5 m2)

Modification MV Switch Gear Room 1.00 Ls Rp - Rp - Rp - Rp -


Cubicle Steel Plate and Stiffener including Steel Door (1800 H, 500 W, 700 L)
Concrete Cable Trench Including Cover 300 W 300 H 3000 L 100 thick
Demolish some existing brickwall +(12 m2)
Brick Awal c/w plastering smooth surfaces (12 m2)
Concrete slab, t=12 cm, smooth surface, wiremesh 8-150, (4 m2)
Sand fill (0.5 m3)
Lean Concrete (0.25 m3)

3 REINFORCED CONCRETE

LPG TANK FOUNDATION


CONCRETE FOUNDATION
PILECAP
- Pilecap-3, sizes: (3500W x 3500L x 700D) mm 171.50 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D16-175
Formwork = Plywood 12 mm thickness (once used)

PEDESTAL
- Pedestal: (2100W x 2100D x 1050H) mm 92.61 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-2750)
Rebar = 56-D22
Formwork = Plywood 12 mm thickness (once used)

GRADE BEAM AND CONC. FLOOR


- Grade beam (500Wx700D) mm 17.50 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D16 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Concrete floor 100 mm Thk (1-layers re-bar) 181.58 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-200
Formwork = Plywood 12 mm thickness (once used)

DRAINAGE ARROUND LPG TO WATER PIT


- Drainage Length = 178 M 35.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-200
Formwork = Plywood 12 mm thickness (once used)

WATERPIT (3m W x 3m L x 2.5m D)

CONCRETE FLOOR AND WALL


- Concrete floor 250 mm Thk (2-layers re-bar) 4.00 m3 Rp - Rp - Rp - Rp -

Page 8 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

f'c = 22.83 Mpa (K-275)


Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Concrete wall 200 mm Thk (2-layers re-bar) 6.40 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)

AIR COMPRESSOR UTILITY TANK FOUNDATION


FOOT PLATE
- Foot plate (4000W x 2000L x 800Thk) mm 6.40 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)

PIPE SUPPORT FOUNDATION


Tee post (PS-002)
- Foot plate: (1500 L x 1500 W x 300 thck) mm 7.42 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 900 H) mm 0.99 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Goal Post (PS-003A)
- Foot Plate (1500 L x 2400 W x 300 thck) mm 14.04 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 1000 H) mm 1.17 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Goal Post (PS-003B)
- Foot Plate (1500 L x 2600 W x 300 thck) mm 8.19 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 1000 H) mm 0.63 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Goal Post (PS-003C)
- Foot Plate (1500 L x 2800 W x 300 thck) mm 54.18 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 1000 H) mm 3.87 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Goal Post (PS-003D)
- Foot Plate (1500 L x 3250 W x 300 thck) mm 2.93 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 1000 H) mm 0.18 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Goal Post (PS-003E)
- Foot Plate (1500 L x 1500 W x 300 thck) mm 13.50 m3 Rp - Rp - Rp - Rp -

Page 9 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

f'c = 18.67 Mpa (K-225)


Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 1000 H) mm 1.80 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Sleeper (PS-001A)
- Foot Plate (700 L x 700 W x 300 thck) mm 5.88 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 W x 1000 H) mm 3.60 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
Sleeper (PS-001B)
- Foot Plate (800 L x 800 W x 300 thck) mm 6.14 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (500 L x 300 W x 1000 H) mm
f'c = 18.67 Mpa (K-225) 4.80 m3 Rp - Rp - Rp - Rp -
Rebar = 10-D13
Formwork = Plywood 12 mm thickness (once used)
Sleeper (PS-001C)
- Foot Plate (1300 L x 800 W x 300 thck) mm 0.94 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (800 L x 300 W x 1000 H) mm 0.72 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 14-D13
Formwork = Plywood 12 mm thickness (once used)
Sleeper (PS-001D)
- Foot Plate (1300 L x 1000 W x 300 thck) mm 1.95 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (1000 L x 300 Wx 1000 H) mm 1.50 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 18-D13
Formwork = Plywood 12 mm thickness (once used)
Sleeper (PS-001E)
- Foot Plate (1300 L x 1600 W x 300 thck) mm 4.99 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (1600 L x 300 Wx 100 H) mm 3.84 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 24-D13
Formwork = Plywood 12 mm thickness (once used)
Sleeper (PS-001F)
- Foot Plate (1300 L x 2300 W x 300 thck) mm 1.79 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (2300 L x 300 Wx 1000 H) mm 1.38 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 34-D13
Formwork = Plywood 12 mm thickness (once used)

PIPE BRIDGE FOUNDATION


PS-001
- Foot Plate (1700 L x 1700 W x 300 thck) mm 5.20 m3 Rp - Rp - Rp - Rp -

Page 10 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

f'c = 18.67 Mpa (K-225)


Rebar = D13-150
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 Wx 1000 H) mm 0.54 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
PS-002
- Foot Plate (3800 L x 1900 W x 300 thck) mm 4.33 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D13-175
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 Wx 1000 H) mm 0.36 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)

FILLING SHED FOUNDATION

- Foot Plate (800 L x 800 W x 450 thck) mm 2.30 m3 Rp - Rp - Rp - Rp -


f'c = 22.83 Mpa (K-275)
Rebar = D13-150
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (350 L x 350 Wx 1300 H) mm 1.27 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (200Wx300D) mm 2.16 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)

COOLING WATER TANK FOUNDATION

- Foot Plate (Dia = 25 m x 700 thck) mm 343.61 m3 Rp - Rp - Rp - Rp -


f'c = 22.83 Mpa (K-275)
Rebar = D13-150
Formwork = Plywood 12 mm thickness (once used)
- Asphalt Sheet thick 50 mm 24.54 m3 Rp - Rp - Rp - Rp -
- Rabat beton tebal 10 cm lebar 1 m, wirmesh dia. 6-150 8.16 m3 Rp - Rp - Rp - Rp -
- Finishing beton tebal 7 cm lebar 1 m, wirmesh dia. 6-150 5.71 m3 Rp - Rp - Rp - Rp -
.- Tanah Urug 77.15 m3 Rp - Rp - Rp - Rp -

WATER PUMP SHELTER FOUNDATION


PUMP FOUNDATION
- Foot Plate (1200 L x 2700 W x 650 thck) mm 4.21 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D16-175
Formwork = Plywood 12 mm thickness (once used)
SHELTER FOUNDATION
- Foot Plate (800 L x 800 W x 400 thck) mm 1.02 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 Wx 800 H) mm 0.29 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (250 Wx400 D) mm 2.40 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Concrete floor (8000 L x 9000 W x 150 thk) mm 10.80 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-125

Page 11 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Formwork = Plywood 12 mm thickness (once used)


- Cable Trench (400 L x 400 W x 70 thck) mm 1.12 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)

WEIGHT BRIDGE SHELTER FOUNDATION


BRIDGE FOUNDATION
- Foot Plate (16000 L x 3500 W x 1000 thck) mm 34.65 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D19-200
Formwork = Plywood 12 mm thickness (once used)
TYPE F1
- Foot Plate (700 L x 700 W x 500 thck) mm 1.96 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-175
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (350 L x 250 Wx 1700 H) mm 1.19 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (200 Wx350 D) mm 2.52 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
TYPE F2
- Foot Plate (700 L x 700 W x 500 thck) mm 3.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-175
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (250 L x 250 Wx 4000 H) mm 1.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (200 Wx300 D) mm 0.96 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Concrete floor (6000 L x 6000 W x 100 thk) mm 3.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-200
Formwork = Plywood 12 mm thickness (once used)
- Beam (200 Wx300 D) mm 1.44 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Concrete floor (6000 L x 6000 W x 100 thk) mm 3.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-200
Formwork = Plywood 12 mm thickness (once used)

ROAD & DRAINAGE FOUNDATION


ROAD
- Slab (250 thck) mm 1,909.82 m3 Rp - Rp - Rp - Rp -
f'c = 28 Mpa (K-350)
Rebar = Wire mesh M10-150
Formwork = Plywood 12 mm thickness (once used)
Asphalt 70 thick 2,289.73 m2
DRAINAGE
- Slab (400 W x 100 thck) mm 203.28 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)
KANSTIN ukuran 40x25x15x13 880.00 m Rp - Rp - Rp - Rp -

Page 12 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

FENCE & GATE FOUNDATION


- Foot Plate (1200 L x 1200 W x 300 thck) mm 99.36 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (400 L x 400 W x 700 H) mm 25.76 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = 8-D10
Formwork = Plywood 12 mm thickness (once used)
- Tie Beam (300 W x 200 H x 2500 L) mm 34.33 m3 Rp - Rp - Rp - Rp -
f'c = 18.67 Mpa (K-225)
Rebar = D8-200
Formwork = Plywood 12 mm thickness (once used)

SECURITY POST FOUNDATION


TYPE F2
- Foot Plate (800 L x 800 W x 400 thck) mm 1.02 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 Wx 500 H) mm 0.18 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (200 Wx300 D) mm 1.44 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
Formwork = Plywood 12 mm thickness (once used)
- Kolom (300 L x 300 Wx 3000 H) mm 1.08 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Beam (200 Wx300 D) mm 1.44 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Slab (3000 L x 4000 W x 150 thk) mm 1.80 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-200
Formwork = Plywood 12 mm thickness (once used)

TRANSFORMER BUILDING FOUNDATION


TRANSFORMER FOUNDATION
- Foot Plate (1100 L x 1700 W x 650 thck) mm 1.22 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-125
Formwork = Plywood 12 mm thickness (once used)
TYPE F1
- Foot Plate (1500 L x 1500 W x 300 thck) mm 2.70 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (250 L x 350 Wx 1000 H) mm 0.35 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (250 Wx300 D) mm 1.20 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 9-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Concrete floor (5500 L x 7000 W x 150 thk) mm 5.78 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-100

Page 13 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Formwork = Plywood 12 mm thickness (once used)


- Cable Trench (400 L x 300 W x 100 thck) mm 0.70 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)

GENSET FOUNDATION

- Foot Plate (1550 L x 3850 W x 650 thck) mm 3.88 m3 Rp - Rp - Rp - Rp -


f'c = 22.83 Mpa (K-275)
Rebar = D13-125
Formwork = Plywood 12 mm thickness (once used)
- Cable Trench (400 L x 300 W x 100 thck) mm 0.42 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)

FILLING PUMP SHELTER FOUNDATION


PUMP FOUNDATION
- Foot Plate (1000 L x 2500 W x 600 thck) mm 3.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-125
Formwork = Plywood 12 mm thickness (once used)
TYPE F1
- Foot Plate (800 L x 800 W x 300 thck) mm 0.77 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D13-200
Formwork = Plywood 12 mm thickness (once used)
- Pedestal (300 L x 300 Wx 800 H) mm 0.29 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D13
Formwork = Plywood 12 mm thickness (once used)
- Grade Beam (250 Wx400 D) mm 2.40 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13 (both top and bottom)
Formwork = Plywood 12 mm thickness (once used)
- Concrete floor (8000 L x 8000 W x 150 thk) mm 9.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = Wire mesh M10-100
Formwork = Plywood 12 mm thickness (once used)
- Cable Trench (400 L x 400 W x 100 thck) mm 0.96 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)

CONTROL ROOM BUILDING


FOOT PLATE
- Foot plate-1, sizes: (1050W x 2100L x 500D) mm 4.41 m3 Rp - Rp - Rp - Rp -
f'c = 21 Mpa (K-250)
Rebar = D16-200
Formwork = Plywood 12 mm thickness (once used)

PEDESTAL
- Pedestal : (400W x 400D x 800H) mm 0.8 0.51 m3 Rp - Rp - Rp - Rp -
f'c = 21 Mpa (K-250)
Rebar = 16-D19
Formwork = Plywood 12 mm thickness (twice used)

COLUMN
- Column : (400W x 400D x 8000H) mm 5.12 m3 Rp - Rp - Rp - Rp -
f'c = 21 Mpa (K-250)
Rebar = 16-D19
Formwork = Plywood 12 mm thickness (twice used)

GRADE BEAM & T-BEAM AND CONC. FLOOR

Page 14 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Ground Floor
- Main Grade beam (250Wx400D) mm 2.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 9-D16 endspan, Mid Span 8 D-16
Formwork = Plywood 12 mm thickness (once used)
- Second Grade beam (250Wx400D) mm 2.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D16
Formwork = Plywood 12 mm thickness (one used)
- Concrete floor 120 mm Thk (2-layers re-bar) 3.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = P10-200
Formwork = Plywood 12 mm thickness (twice used)
- Terrace Conc. floor 100 mm Thk (1-layer bar) 1.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (twice used)
- Terrace Conc. floor 100 mm Thk (1-layer bar) 1.20 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = M8-200
Formwork = Plywood 12 mm thickness (twice used)
- Terrace stiffener beam (150W x 200D)mm 0.48 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 4-D13
Formwork = Plywood 12 mm thickness (twice used)
- Terrace stiffener beam (150W x 200D)mm 0.48 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 4-D13
Formwork = Plywood 12 mm thickness (twice used)

First Floor ( TOC. EL. )


- Main T-beam (400Wx500D) mm 4.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 9-D16
Formwork = Plywood 12 mm thickness (twice used)
- Second T-beam (200Wx250D) mm 0.55 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D16
Formwork = Plywood 12 mm thickness (twice used)
- Second. T-beam (200Wx350D) mm 0.77 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 8-D16
Formwork = Plywood 12 mm thickness (twice used)
- Concrete floor 120 mm Thk (2-layers re-bar) 2.28 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-175
Formwork = Plywood 12 mm thickness (twice used)

Roof ( TOC. EL. + 8.0)


- Main T-beam (250Wx400D) mm 2.00 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D16
Formwork = Plywood 12 mm thickness (twice used)
- Second T-beam (200Wx250D) mm 0.50 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-250)
Rebar = 6-D13
Formwork = Plywood 12 mm thickness (twice used)
- Second.T-beam (200Wx200D) mm 0.48 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 4-D13
Formwork = Plywood 12 mm thickness (twice used)
- Concrete Roof 100 mm Thk (1-layers re-bar) 3.60 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = P10-200
Formwork = Plywood 12 mm thickness (twice used)

Page 15 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- Conc. parapet (80Thk x 600H) mm (1-layer bar) 1.54 m3 Rp - Rp - Rp - Rp -


f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)

STAIR CASE
- Staircase (0.75 m W x 0.15 m thk floor) 0.61 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)
- "BORDES 1" Floor (1.1 W x 1.35 L) m 0.22 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = D10-200
Formwork = Plywood 12 mm thickness (once used)
- Bordes beam stiffener (200Wx250D) mm 0.35 m3 Rp - Rp - Rp - Rp -
f'c = 22.83 Mpa (K-275)
Rebar = 6-D13

4 STRUCTURAL STEEL

Pipe Support (PS -002) T post


- Column WH 100 x 100 x 6 x 8 190.00 kg Rp - Rp - Rp - Rp -
- Beam WH 100 x 100 x 6 x 8 190.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 10 mm 54.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 44.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 14.00 m2 Rp - Rp - Rp - Rp -

Pipe Support (PS -003 A) Goal Post


- Column WH 100 x 100 x 6 x 8 448.00 kg Rp - Rp - Rp - Rp -
- Beam WH 100 x 100 x 6 x 8 537.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 10 mm 128.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 104.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 36.00 m2 Rp - Rp - Rp - Rp -

Pipe Support (PS -003 B) Goal Post


- Column WH 100 x 100 x 6 x 8 241.00 kg Rp - Rp - Rp - Rp -
- Beam WH 100 x 100 x 6 x 8 314.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 10 mm 69.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 56.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 21.00 m2 Rp - Rp - Rp - Rp -

Pipe Support (PS -003 C) Goal Post


- Column WH 100 x 100 x 6 x 8 1,480.00 kg Rp - Rp - Rp - Rp -
- Beam WH 100 x 100 x 6 x 8 2,071.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 10 mm 422.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 344.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 130.00 m2 Rp - Rp - Rp - Rp -

Pipe Support (PS -003 D) Goal Post


- Column WH 100 x 100 x 6 x 8 69.00 kg Rp - Rp - Rp - Rp -
- Beam WH 100 x 100 x 6 x 8 112.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 10 mm 20.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 16.00 Ea Rp - Rp - Rp - Rp -

Page 16 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Painting Steel structure 7.00 m2 Rp - Rp - Rp - Rp -

Pipe Support (PS -003 E) Goal Post


- Column WH 100 x 100 x 6 x 8 344.00 kg Rp - Rp - Rp - Rp -
- Beam WH 100 x 100 x 6 x 8 654.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 10 mm 99.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 80.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 37.00 m2 Rp - Rp - Rp - Rp -

Pipe Sleeper (PS -001 A)


- Embedded Plate thk 10 mm 189.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 160.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 3.00 m2 Rp - Rp - Rp - Rp -

Pipe Sleeper (PS -001 B)


- Embedded Plate thk 10 mm 201.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 128.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 3.00 m2 Rp - Rp - Rp - Rp -

Pipe Sleeper (PS -001 C)


- Embedded Plate thk 10 mm 33.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 18.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 1.00 m2 Rp - Rp - Rp - Rp -

Pipe Sleeper (PS -001 D)


- Embedded Plate thk 10 mm 71.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 30.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 1.00 m2 Rp - Rp - Rp - Rp -

Pipe Sleeper (PS -001 E)


- Embedded Plate thk 10 mm 189.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 48.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 3.00 m2 Rp - Rp - Rp - Rp -

Pipe Sleeper (PS -001 F)


- Embedded Plate thk 10 mm 70.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 12 20.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 1.00 m2 Rp - Rp - Rp - Rp -

PIPE BRIDGE

Page 17 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- Column WF 200 x 100 x 5.5 x 8 1,278.00 kg Rp - Rp - Rp - Rp -


- Beam WF 200 x 100 x 5.5 x 8 511.20 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 1,288.00 kg Rp - Rp - Rp - Rp -
- Bracing L 70 x 70 x 6 512.00 kg Rp - Rp - Rp - Rp -
- Bracing L 50 x 50 x 5 162.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 19 mm 94.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 16 40.00 Ea Rp - Rp - Rp - Rp -

Painting Steel structure 166.00 m2 Rp - Rp - Rp - Rp -

LPG FILLING SHED SHELTER

- Column SH 200 x 200 x 8 x 12 3,652.68 kg Rp - Rp - Rp - Rp -


- Beam SH 250 x 125 x 6 x 9 1,658.00 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 196.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 2,300.40 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 504.00 kg Rp - Rp - Rp - Rp -
- Purlin 150 x 65 x 20 x 3.2 1,504.80 kg Rp - Rp - Rp - Rp -
- Tie Rod Dia 16 165.00 kg Rp - Rp - Rp - Rp -
- Sagrod Dia 10 119.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 19 mm 162.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 16 48.00 Ea Rp - Rp - Rp - Rp -
- Metal Sheet 0.45 Thk 320.00 m2 Rp - Rp - Rp - Rp -
- Alumunium Comp. Panel 4 Thk 1.00 Ls Rp - Rp - Rp - Rp -
- Grill 1.00 Ls Rp - Rp - Rp - Rp -

Painting Steel structure 466.00 m2 Rp - Rp - Rp - Rp -

FIRE WATER PUMP SHELTER

- Column SH 200 x 100 x 5.5 x 8 299.00 kg Rp - Rp - Rp - Rp -


- Beam SH 200 x 100 x 5.5 x 8 299.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 256.00 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 112.00 kg Rp - Rp - Rp - Rp -
- Purlin LC 150 x 65 x 20 x 3.2 541.00 kg Rp - Rp - Rp - Rp -
- Tie Rod Dia 16 30.00 kg Rp - Rp - Rp - Rp -
- Sagrod Dia 10 12.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 19 mm 45.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 16 16.00 Ea Rp - Rp - Rp - Rp -
- Metal Sheet 0.45 Thk 72.00 m2 Rp - Rp - Rp - Rp -
- Alumunium Comp. Panel 4 Thk

Painting Steel structure 78.00 m2 Rp - Rp - Rp - Rp -

WEIGHT BRIDGE SHELTER

- Column SH 200 x 100 x 5.5 x 8 904.00 kg Rp - Rp - Rp - Rp -


- Beam SH 300 x 150 x 6.5 x 9 829.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 171.00 kg Rp - Rp - Rp - Rp -
- Beam UNP 200 x 90 x 7.5 x 11 380.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 767.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 171.00 kg Rp - Rp - Rp - Rp -
- Purlin LC 150 x 65 x 20 x 3.2 1,203.20 kg Rp - Rp - Rp - Rp -
- Tie Rod Dia 16 83.00 kg Rp - Rp - Rp - Rp -
- Sagrod Dia 10 50.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 19 mm 90.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 16 32.00 Ea Rp - Rp - Rp - Rp -
- Metal Sheet 0.45 Thk 198.00 m2 Rp - Rp - Rp - Rp -
- Alumunium Comp. Panel 4 Thk

Page 18 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Painting Steel structure 225.00 m2 Rp - Rp - Rp - Rp -

FILLING PUMP SHELTER

- Column SH 200 x 100 x 5.5 x 8 299.00 kg Rp - Rp - Rp - Rp -


- Beam SH 150 x 75 x 5 x 7 84.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 256.00 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 56.00 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 56.00 kg Rp - Rp - Rp - Rp -
- Beam SH 200 x 100 x 5.5 x 8 256.00 kg Rp - Rp - Rp - Rp -
- Purlin LC 150 x 65 x 20 x 3.2 481.00 kg Rp - Rp - Rp - Rp -
- Tie Rod Dia 16 24.00 kg Rp - Rp - Rp - Rp -
- Sagrod Dia 10 12.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 19 mm 45.00 kg Rp - Rp - Rp - Rp -
- Grating 57.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 16 16.00 Ea Rp - Rp - Rp - Rp -
- Metal Sheet 0.45 Thk 64.00 m2 Rp - Rp - Rp - Rp -
- Alumunium Comp. Panel 4 Thk

Painting Steel structure 75.00 m2 Rp - Rp - Rp - Rp -

TRANSFORMER BUILDING

- Column SH 200 x 100 x 5.5 x 8 299.00 kg Rp - Rp - Rp - Rp -


- Beam SH 150 x 75 x 5 x 7 140.00 kg Rp - Rp - Rp - Rp -
- Beam SH 150 x 75 x 5 x 7 168.00 kg Rp - Rp - Rp - Rp -
- Purlin LC 150 x 65 x 20 x 3.2 445.00 kg Rp - Rp - Rp - Rp -
- Tie Rod Dia 16 33.00 kg Rp - Rp - Rp - Rp -
- Sagrod Dia 10 8.00 kg Rp - Rp - Rp - Rp -
- Embedded Plate thk 19 mm 45.00 kg Rp - Rp - Rp - Rp -
- Grating 48.00 kg Rp - Rp - Rp - Rp -
- Anchor bolt Dia 16 16.00 Ea Rp - Rp - Rp - Rp -
- Metal Sheet 0.45 Thk 43.66 m2 Rp - Rp - Rp - Rp -
- Harmonica Wire Fence 28.90 m2 Rp - Rp - Rp - Rp -
- Grill 1.50 m2 Rp - Rp - Rp - Rp -

Painting Steel structure 58.00 m2 Rp - Rp - Rp - Rp -

FENCE & GATE

- Column Pipa 6" 162.00 kg Rp - Rp - Rp - Rp -


- Column Pipa 2" 62.00 kg Rp - Rp - Rp - Rp -
- Column Pipa 2" 26.00 kg Rp - Rp - Rp - Rp -
- Beam Pipa 2" 98.00 kg Rp - Rp - Rp - Rp -
- Bracing Pipa 2" 123.00 kg Rp - Rp - Rp - Rp -
- Wire Support L 50x50x50 455.00 kg Rp - Rp - Rp - Rp -
- Sagrod Dia 10 7.00 kg Rp - Rp - Rp - Rp -
- Barb Wire 1,500.00 m Rp - Rp - Rp - Rp -
- Chain Link 11.91 m2 Rp - Rp - Rp - Rp -

Painting Steel structure 38.00 m2 Rp - Rp - Rp - Rp -

Total 3 Rp - Rp -

Page 19 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

4 PEKERJAAN MEKANIKAL DAN PEMIPAAN


A MEKANIKAL
Tag Number Equipment Name Capacity
1 T-5/6 LPG STORAGE TANK 1500 MT 2 Unit - US$ - Include - US$ - Include
2 P-11/12 LPG TRUCK FILLING PUMP 167 m3/hr (rated) SEAL : DOUBLE MECHANICAL SEAL 2 Unit - US$ Rp - - US$ Rp -
3 LH-05/06 LPG TRUCK LOADING ARM 45 MT/hr 2 Unit - US$ Rp - - US$ Rp -
4 K-01 A/B AIR COMPRESSOR PACKAGE 37 Sm3/hr 2 Unit - US$ Rp - - US$ Rp -
5 V-01 UTILITY AIR RECEIVER 1.8 m3 1 Unit - US$ Rp - - US$ Rp -
6 V-02 INSTRUMENT AIR RECEIVER 5.56 m3 1 Unit - US$ Rp - - US$ Rp -
7 T-101 DIESEL STORAGE TANK 3 m3 1 Unit Rp - Rp - Rp - Rp -
8 F-101 A/B DIESEL OIL TRANSFER FILTER (Note 1) 2 Unit - US$ Rp - - US$ Rp -
9 P-17 DEEP WELL PUMP 72 m3/hr 1 Unit Rp - Rp - Rp - Rp -
10 T-7 FIRE WATER STORAGE TANK 4500 m3 1 Unit Rp - Rp - Rp - Rp -
11 P-13/14 FIRE WATER PUMP 454 m3/hr 2 Unit - US$ Rp - - US$ Rp -
12 P-15 JOCKEY PUMP 11 m3/hr 1 Unit - US$ Rp - - US$ Rp -
13 P-17 WATER PIT PUMP 30 m3/hr 1 Unit Rp - Rp - Rp - Rp -
14 WEIGHT BRIDGE 60 TON 1 Unit Rp - Rp - Rp - Rp -

B PEMIPAAN (Pipe, Fitting, Valve & acessories) 0.0 CLASS/SCH


A Piping Class A2A - LPG and Vapor
1 Pipe Niple , A106 Gr B, PE/Thrd, SMLS, ASME B36.10, 100mm Length. 3/4" 80 39 M Rp - Rp - Rp - Rp -
2 Pipe, API 5L Gr. B, ERW, BE, Sch.80, ASME B36.10M 2" 80 66 M Rp - Rp - Rp - Rp -
3 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 3" STD 367 M Rp - Rp - Rp - Rp -
4 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 4" STD 605 M Rp - Rp - Rp - Rp -
5 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 6" STD 305 M Rp - Rp - Rp - Rp -
6 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 8" STD 12 M Rp - Rp - Rp - Rp -
7 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 10" STD 750 M Rp - Rp - Rp - Rp -

8 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 3" 80 10 EA Rp - Rp - Rp - Rp -
9 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 4" 80 14 EA Rp - Rp - Rp - Rp -
10 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 6" STD 4 EA Rp - Rp - Rp - Rp -
11 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 10" STD 6 EA Rp - Rp - Rp - Rp -
12 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 2" 80 15 EA Rp - Rp - Rp - Rp -
13 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 3" STD 26 EA Rp - Rp - Rp - Rp -
14 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 4" STD 20 EA Rp - Rp - Rp - Rp -
15 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 6" STD 20 EA Rp - Rp - Rp - Rp -
16 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 10" STD 25 EA Rp - Rp - Rp - Rp -
17 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 2" STD 6 EA Rp - Rp - Rp - Rp -
18 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 3" STD 3 EA Rp - Rp - Rp - Rp -
19 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 4" STD 8 EA Rp - Rp - Rp - Rp -
20 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 6" STD 2 EA Rp - Rp - Rp - Rp -
21 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10" STD 6 EA Rp - Rp - Rp - Rp -
22 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 6"x2" STD 3 EA Rp - Rp - Rp - Rp -
23 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 6"x3" STD 3 EA Rp - Rp - Rp - Rp -
24 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 6"x4" STD 1 EA Rp - Rp - Rp - Rp -
25 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10"x4" STD 4 EA Rp - Rp - Rp - Rp -
26 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10"x8" STD 2 EA Rp - Rp - Rp - Rp -
27 Co. Reducer, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 6"x4" STD 2 EA Rp - Rp - Rp - Rp -
28 Co. Reducer, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 8"x6" STD 2 EA Rp - Rp - Rp - Rp -
29 Co. Reducer, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10"x6" STD 1 EA Rp - Rp - Rp - Rp -
30 Split Tee, A234 Gr. WPB, SMLS, BE, ASME B16.9 3" STD 1 EA Rp - Rp - Rp - Rp -
31 Split Tee, A234 Gr. WPB, SMLS, BE, ASME B16.9 4" STD 1 EA Rp - Rp - Rp - Rp -
32 Split Tee, A234 Gr. WPB, SMLS, BE, ASME B16.9 6" STD 1 EA Rp - Rp - Rp - Rp -

33 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 2" #300 82 EA Rp - Rp - Rp - Rp -


34 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 3" #300 35 EA Rp - Rp - Rp - Rp -
35 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 4" #300 46 EA Rp - Rp - Rp - Rp -
36 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 6" #300 442 EA Rp - Rp - Rp - Rp -
37 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 8" #300 4 EA Rp - Rp - Rp - Rp -
38 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 10" #300 50 EA Rp - Rp - Rp - Rp -
39 Blind Flange, ASTM A105, RF, ASME B16.5 2" #300 12 EA Rp - Rp - Rp - Rp -
40 Blind Flange, ASTM A105, RF, ASME B16.5 3" #300 2 EA Rp - Rp - Rp - Rp -
41 Blind Flange, ASTM A105, RF, ASME B16.5 4" #300 4 EA Rp - Rp - Rp - Rp -
42 Blind Flange, ASTM A105, RF, ASME B16.5 6" #300 4 EA Rp - Rp - Rp - Rp -

Page 20 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

43 Blind Flange, ASTM A105, RF, ASME B16.5 10" #300 7 EA Rp - Rp - Rp - Rp -


44 Spectacle Blind, RF, ASME B16.48 4" #300 2 EA Rp - Rp - Rp - Rp -
45 Spectacle Blind, RF, ASME B16.48 10" #300 4 EA Rp - Rp - Rp - Rp -

46 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 2" #300 87 EA Rp - Include Rp - Include -
47 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 3" #300 41 EA Rp - Include Rp - Include -
48 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 4" #300 49 EA Rp - Include Rp - Include -
49 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 6" #300 43 EA Rp - Include Rp - Include -
50 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 8" #300 12 EA Rp - Include Rp - Include -
51 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 10" #300 50 EA Rp - Include Rp - Include -

ASTM A193 Gr B7 / A194 Gr 2H Heavy Hex, Fluorocarbon Plated;


52 5/8" X 90 Long 2" #300 696 EA Rp - Include Rp - Include -
53 3/4" X 115 Long 3" #300 328 EA Rp - Include Rp - Include -
54 3/4" X 120 Long 4" #300 392 EA Rp - Include Rp - Include -
55 3/4" X 130 Long 6" #300 516 EA Rp - Include Rp - Include -
56 7/8" X 130 Long 8" #300 144 EA Rp - Include Rp - Include -
57 1" X 170 Long 10" #300 300 EA Rp - Include Rp - Include -

58 Sockolet; ASTM A105; BW x SW; ASME B16.11 3"x3/4" #6000 1 EA Rp - Rp - Rp - Rp -


59 Sockolet; ASTM A105; BW x SW; ASME B16.11 4"x3/4" #6000 6 EA Rp - Rp - Rp - Rp -
60 Sockolet; ASTM A105; BW x SW; ASME B16.11 6"x3/4" #6000 8 EA Rp - Rp - Rp - Rp -
61 Sockolet; ASTM A105; BW x SW; ASME B16.11 8"x3/4" #6000 10 EA Rp - Rp - Rp - Rp -
62 Sockolet; ASTM A105; BW x SW; ASME B16.11 10"x3/4" #6000 8 EA Rp - Rp - Rp - Rp -

Ball Valve; min. seat rating 1500# CWP; F-Bore; Floating ball; Scrd /SW / Scrd x SW; BB; Replaceable ball &
63 seats; ASTM A105; ASTM A182 316SS ball & stem; LO; Teflon or reinforced teflon or reinforced Viton 3/4" #800 43 EA - US$ Rp - - US$ Rp -
seats; API 608; API 598; API 607.

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; ASTM
64 A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or reinforced Viton Seats; 2" #300 32 EA - US$ Rp - - US$ Rp -
Floating ball; LO; API 6D; API 6FA..

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; ASTM
65 A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or reinforced Viton Seats; 3" #300 11 EA - US$ Rp - - US$ Rp -
Floating ball; LO; API 6D; API 6FA.

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; BB;
66 ASTM A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or reinforced Viton Seats; 4" #300 11 EA - US$ Rp - - US$ Rp -
Floating ball; LO; API 6D; API 6FA.

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; ASTM
67 A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or reinforced Viton Seats; 6" #300 12 EA - US$ Rp - - US$ Rp -
Trunnion mounted; GO; API 6D; API 6FA..

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; ASTM
68 A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or reinforced Viton Seats; 8" #300 4 EA - US$ Rp - - US$ Rp -
Trunnion mounted; GO; API 6D; API 6FA..

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; ASTM
69 A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or reinforced Viton Seats; 10" #300 7 EA - US$ Rp - - US$ Rp -
Trunnion mounted; GO; API 6D; API 6FA.

70 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 2" #300 3 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD.

71 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 4" #300 3 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD.

72 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 6" #300 2 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD; Lifting lug.

Globe Valve; RF; FE; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable disc & seat; ASTM A216
73 WCB; 11.5-13.5% Cr Stem, disc & seat; Stellited disc & seat; Graphited NAF Packing; HW operated; API 3" #300 2 EA - US$ Rp - - US$ Rp -
600; API 598; API 6FA.

Globe Valve; RF; FE; BB; OS & Y; Rising stem; Plug disc; Replaceable disc & seat; ASTM A216 WCB; 11.5-
74 13.5% Cr Stem, disc & seat; Stellited disc & seat; Graphited NAF Packing; HW operated; API 600; API 598; 4" #300 3 EA - US$ Rp - - US$ Rp -
API 6FA.

Page 21 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

75 Y-Strainer; RF; FE; BC; A216 WCB; Blind Flange with 3/4 Plug; SS Screen; Manufactured Standard. 8" #300 2 EA - US$ Rp - - US$ Rp -

76 Flexible Joint 4" #300 2 EA Rp - Rp - Rp - Rp -


77 Flexible Joint 10" #300 4 EA Rp - Rp - Rp - Rp -

B Piping Class A1A - Fire Water, Diesel Fuel, Drain


1 Pipe Niple , A106 Gr B, PE/Thrd, SMLS, ASME B36.10, 3/4" 80 29 EA Rp - Rp - Rp - Rp -
2 Pipe Niple , A106 Gr B, PE/Thrd, SMLS, ASME B36.10, 1" 80 24 EA Rp - Rp - Rp - Rp -
3 Pipe, API 5L Gr. B, ERW, PE, Sch.80, ASME B36.10M 1 1/2" 80 90 M Rp - Rp - Rp - Rp -
4 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 2" 80 73 M Rp - Rp - Rp - Rp -
5 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 3" STD 2 M Rp - Rp - Rp - Rp -
6 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 4" STD M Rp - Rp - Rp - Rp -
7 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 6" STD 130 M Rp - Rp - Rp - Rp -
8 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 8" STD 14 M Rp - Rp - Rp - Rp -
9 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 10" STD 116 M Rp - Rp - Rp - Rp -
10 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 12" STD 24 M Rp - Rp - Rp - Rp -
11 Pipe, API 5L Gr. B, ERW, BE, STD, ASME B36.10 M 16" STD 67 M Rp - Rp - Rp - Rp -

12 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 6" STD 4 EA Rp - Rp - Rp - Rp -
13 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 10" STD 4 EA Rp - Rp - Rp - Rp -
14 Elbow 45 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 16" STD 1 EA Rp - Rp - Rp - Rp -
15 Elbow 90 deg; #3000, SW; ASTM A105; ASME B16.11. 1" #3000 4 EA Rp - Rp - Rp - Rp -
16 Elbow 90 deg; #3000, SW; ASTM A105; ASME B16.11. 1 1/2" #3000 16 EA Rp - Rp - Rp - Rp -
17 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 2" 80 4 EA Rp - Rp - Rp - Rp -
18 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 3" STD 6 EA Rp - Rp - Rp - Rp -
19 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 4" STD 4 EA Rp - Rp - Rp - Rp -
20 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 6" STD 11 EA Rp - Rp - Rp - Rp -
21 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 10" STD 23 EA Rp - Rp - Rp - Rp -
22 Elbow 90 deg; A234 Gr. WPB; WTMP; SMLS; LR; BE; ASME B16.9. 16" STD 1 EA Rp - Rp - Rp - Rp -
23 Equal Tee, #3000, SW; ASTM A105; ASME B16.11. 1 1/2" #3000 3 EA Rp - Rp - Rp - Rp -
24 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 3" STD 2 EA Rp - Rp - Rp - Rp -
25 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 4" STD 2 Rp - Rp - Rp - Rp -
26 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10" STD 11 EA Rp - Rp - Rp - Rp -
27 Equal Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 16" STD 1 EA Rp - Rp - Rp - Rp -
28 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10"x4" STD 4 EA Rp - Rp - Rp - Rp -
29 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10"x6" STD 4 EA Rp - Rp - Rp - Rp -
30 Reducer Tee, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 16"x12" STD 2 EA Rp - Rp - Rp - Rp -
31 Con. Reducer, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 3"x2" STD 2 EA Rp - Rp - Rp - Rp -
32 Con. Reducer, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 10"x6" STD 4 EA Rp - Rp - Rp - Rp -
33 Con. Reducer, A234 Gr. WPB, SMLS, BE, WTMP, ASME B16.9 12"x8" STD 2 EA Rp - Rp - Rp - Rp -

34 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 1 1/2" #150 7 EA Rp - Rp - Rp - Rp -


35 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 2" #150 7 EA Rp - Rp - Rp - Rp -
36 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 3" #150 13 EA Rp - Rp - Rp - Rp -
37 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 4" #150 8 EA Rp - Rp - Rp - Rp -
38 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 6" #150 14 EA Rp - Rp - Rp - Rp -
39 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 8" #150 2 EA Rp - Rp - Rp - Rp -
40 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 10" #150 49 EA Rp - Rp - Rp - Rp -
41 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 12" #150 5 EA Rp - Rp - Rp - Rp -
42 Flange, ASTM A105, RFWN, BTMP, ASME B16.5 16" #150 3 EA Rp - Rp - Rp - Rp -
43 Blind Flange, ASTM A105, RF, ASME B16.5 10" #150 4 EA Rp - Rp - Rp - Rp -
44 Blind Flange, ASTM A105, RF, ASME B16.5 16" #150 2 EA Rp - Rp - Rp - Rp -

45 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 1 1/2" #150 7 EA Rp - Include Rp - Include -

46 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 2" #150 16 EA Rp - Include Rp - Include -

47 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 3" #150 15 EA Rp - Include Rp - Include -

Page 22 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

48 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 4" #150 10 EA Rp - Include Rp - Include -

49 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 6" #150 13 EA Rp - Include Rp - Include -

50 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 8" #150 2 EA Rp - Include Rp - Include -

51 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 10" #150 49 EA Rp - Include Rp - Include -

52 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 12" #150 6 EA Rp - Include Rp - Include -

53 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 16" #150 4 EA Rp - Include Rp - Include -

ASTM A193 Gr B7 / A194 Gr 2H Heavy Hex, Fluorocarbon Plated;


54 1/2" X 75 Long 1 1/2" #150 28 EA Rp - Include Rp - Include -
55 5/8" x 85 Long 2" #150 64 EA Rp - Include Rp - Include -
56 5/8" X 90 Long 3" #150 60 EA Rp - Include Rp - Include -
57 5/8" X 90 Long 4" #150 80 EA Rp - Include Rp - Include -
58 3/4" x 105 Long 6" #150 104 EA Rp - Include Rp - Include -
59 3/4" x 115 Long 8" #150 16 EA Rp - Include Rp - Include -
60 7/8" x 125 Long 10" #150 588 EA Rp - Include Rp - Include -
61 7/8" x 130 Long 12" #150 72 EA Rp - Include Rp - Include -
62 1" x 150 Long 16" #150 64 EA Rp - Include Rp - Include -
63 PLUG, HEX HEAD, MPT, ASME B16.11 3/4" #800 6 EA Rp - Include Rp - Include -

64 Sockolet; ASTM A105; BW x SW; ASME B16.11 3"x3/4" #3000 4 EA Rp - Rp - Rp - Rp -


65 Sockolet; ASTM A105; BW x SW; ASME B16.11 6"x3/4" #3000 1 EA Rp - Rp - Rp - Rp -
66 Sockolet; ASTM A105; BW x SW; ASME B16.11 10"x3/4" #3000 18 EA Rp - Rp - Rp - Rp -
67 Sockolet; ASTM A105; BW x SW; ASME B16.11 12"x3/4" #3000 2 EA Rp - Rp - Rp - Rp -
68 Weldolet; ASTM A105; BW; ASME B16.11 10"x1" #3000 2 EA Rp - Rp - Rp - Rp -
69 Weldolet; ASTM A105; BW; ASME B16.11 12"x3" #3000 1 EA Rp - Rp - Rp - Rp -
70 Weldolet; ASTM A105; BW; ASME B16.11 10"x3" #3000 1 EA Rp - Rp - Rp - Rp -
71 Weldolet; ASTM A105; BW; ASME B16.11 16"x3" #3000 1 EA Rp - Rp - Rp - Rp -
72 Full Coupling; ASTM A105; NPT; ASME B16.11 3/4" #3000 38 EA Rp - Rp - Rp - Rp -
73 Full Coupling; ASTM A105; NPT; ASME B16.11 1 1/2" #3000 1 EA Rp - Rp - Rp - Rp -
74 Full Coupling; ASTM A105; NPT; ASME B16.11 2" #3000 1 EA Rp - Rp - Rp - Rp -

75 Ball Valve; min. seat rating 1500# CWP; F-Bore; Floating ball; Scrd /SW; BB; Replaceable ball & seats; 1 1/2" #1500 8 EA - US$ Rp - - US$ Rp -
ASTM A105; ASTM A182 316SS ball & stem; LO; Reinforced Viton seats; API 608; API 598; API 607.

76 Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; 2" #1500 2 EA - US$ Rp - - US$ Rp -
Reinforced Viton Seats; Floating ball; LO; API 6D; API 6FA..

77 Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; 10" #1500 4 EA - US$ Rp - - US$ Rp -
Reinforced Viton Seats; Trunnion ball; GO; API 6D; API 6FA..

78 Gate Valve ; Scrd/SW ends; BB; OS & Y; Rising stem; Type solid wedge; HW operated; ASTM A105 ; 11.5 – 3/4" #800 29 EA - US$ Rp - - US$ Rp -
13.5% Cr stem, wedge & seat ring; Graphited NAF packing; API 602; API 598; API 607.

79 Gate Valve ; Scrd/SW ends; BB; OS & Y; Rising stem; Type solid wedge; HW operated; ASTM A105 ; 11.5 – 1" #800 2 EA - US$ Rp - - US$ Rp -
13.5% Cr stem, wedge & seat ring; Graphited NAF packing; API 602; API 598; API 607.

80 Gate Valve; RF; FE; BB; OS & Y; Rising stem; Type solid wedge; A216 WCB; 11.5-13.5% Cr stem, wedge & 3" #150 5 EA - US$ Rp - - US$ Rp -
seat ring; Stellited wedge & seat; Graphited NAF packing; HW operated; API 6D; API 6D; API 6FA.

81 Gate Valve; RF; FE; BB; OS & Y; Rising stem; Type solid wedge; A216 WCB; 11.5-13.5% Cr stem, wedge & 4" #150 2 EA - US$ Rp - - US$ Rp -
seat ring; Stellited wedge & seat; Graphited NAF packing; HW operated; API 6D; API 6D; API 6FA.

82 Gate Valve; RF; FE; BB; OS & Y; Rising stem; Type solid wedge; A216 WCB; 11.5-13.5% Cr stem, wedge & 10" #150 10 EA - US$ Rp - - US$ Rp -
seat ring; Stellited wedge & seat; Graphited NAF packing; HW operated; API 6D; API 6D; API 6FA.

Page 23 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

83 Gate Valve; RF; FE; BB; OS & Y; Rising stem; Type solid wedge; A216 WCB; 11.5-13.5% Cr stem, wedge & 12" #150 2 EA - US$ Rp - - US$ Rp -
seat ring; Stellited wedge & seat; Graphited NAF packing; HW operated; API 6D; API 6D; API 6FA.

84 Gate Valve; RF; FE; BB; OS & Y; Rising stem; Type solid wedge; A216 WCB; 11.5-13.5% Cr stem, wedge & 16" #150 1 EA - US$ Rp - - US$ Rp -
seat ring; Stellited wedge & seat; Graphited NAF packing; HW operated; API 6D; API 6D; API 6FA.

85 Swing Check Valve; Scrd/SW ends; BC; Replaceable disc & seat; A105; 11.5 - 13.5% Cr disc & seat; Stellited 1 1/2" #150 1 EA - US$ Rp - - US$ Rp -
disc & seat; API 602.

86 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 2" #150 1 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD; Lifting lug.

87 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 6" #150 1 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD; Lifting lug.

88 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 3" #150 2 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD; Lifting lug.

89 Check Valve; RF: FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body & cap; 11.5- 10" #150 2 EA - US$ Rp - - US$ Rp -
13.5% Cr disc & seat; ASTM A182 F304 hinge pin; ASTM A216 WCB hinge; API 6D; API 6FD; Lifting lug.

90 Y-Strainer; RF; FE; BC; A216 WCB; Blind Flange with 3/4 Plug; SS Screen; Manufactured Standard. 3" #150 2 EA - US$ Rp - - US$ Rp -
91 Y-Strainer; RF; FE; BC; A216 WCB; Blind Flange with 3/4 Plug; SS Screen; Manufactured Standard. 12' #150 1 EA - US$ Rp - - US$ Rp -

C Piping Class C1A - Instrument Air, Utility Air 0.0


1 Pipe Nipple, A106 Gr B, HD Galv, PE/Thrd, SMLS, ASME B36.10, 100L. 3/4" 80 40 EA Rp - Rp - Rp - Rp -
2 Pipe, SMLS, PE, ASTM A106 Gr B, HD Galv., SMLS, ASME B36.10, 1" 40 24 M Rp - Rp - Rp - Rp -
3 Pipe, SMLS, PE, ASTM A106 Gr B, HD Galv., SMLS, ASME B36.10, 1 1/2" 40 1 M Rp - Rp - Rp - Rp -
4 Pipe, API 5L Gr. B, HD Galv., ERW, BE, ASME B36.10M 2" 40 300 M Rp - Rp - Rp - Rp -

5 Elbow 45 deg; BW; ASTM A105 HD Galv.; ASME B16.9. 2" 40 2 EA Rp - Rp - Rp - Rp -


6 Elbow 90 deg; SW; ASTM A105 HD Galv.; ASME B16.11. 1" 40 6 EA Rp - Rp - Rp - Rp -
7 Elbow 90 deg; BW; ASTM A105 HD Galv.; ASME B16.9. 2" 40 42 EA Rp - Rp - Rp - Rp -
8 Equal Tee; BW; ASTM A105 HD Galv.; ASME B16.9. 1" 40 1 EA Rp - Rp - Rp - Rp -
9 Equal Tee; BW; ASTM A105 HD Galv.; ASME B16.9. 2" 40 7 EA Rp - Rp - Rp - Rp -
10 Reducer Tee, ASTM A105, HD Galv., SMLS, SW, ASME B16.11 1"x3/4" #3000 2 EA Rp - Rp - Rp - Rp -
11 Cocentric Reducer; BW; ASTM A105 HD Galv.; ASME B16.9. 2"x1" 40 4 EA Rp - Rp - Rp - Rp -

12 Flange, ASTM A105, HD Galv., RFSW, BTMP, ASME B16.5 1" #150 10 EA Rp - Rp - Rp - Rp -
13 Flange, ASTM A105, HD Galv., RFWN, BTMP, ASME B16.5 2" #150 52 EA Rp - Rp - Rp - Rp -
14 Blind Flange, ASTM A105, HD Galv., RF, ASME B16.5 1" #150 2 EA Rp - Rp - Rp - Rp -
15 Blind Flange, ASTM A105, HD Galv., RF, ASME B16.5 2" #150 11 EA Rp - Rp - Rp - Rp -

16 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 1" #150 19 EA Rp - Include Rp - Include -

17 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 1" #150 1 EA Rp - Include Rp - Include -

18 Gasket; Spiral-Wound W:SS304 /F: Flexible Graphite OIR: W/ Non Asbestos Filler; 4.5MM; ASME B 16.20. 2" #150 52 EA Rp - Include Rp - Include -

ASTM A193 Gr B7 / A194 Gr 2H Heavy Hex, Fluorocarbon Plated;


19 1/2" X 70 Long 1" #150 76 EA Rp - Include Rp - Include -
20 1/2" X 75 Long 1 1/2" #150 4 EA Rp - Include Rp - Include -
21 1/2" X 85 Long 2" #150 208 EA Rp - Include Rp - Include -

22 PLUG, HEX HEAD, MPT, ASME B16.11 3/4" #3000 6 EA Rp - Include Rp - Include -
23 Coupling, ASTM A105, HD Galv.,SW, ASME B16.11 2" #3000 28 EA Rp - Rp Rp - Rp -
24 Weldolet; ASTM A105; BW; HD Galv., ASME B16.11 2"x1 1/2" #3000 1 EA Rp - Rp Rp - Rp -
25 Sockolet; ASTM A105; SW; HD Galv., ASME B16.11 2"x3/4" #3000 40 EA Rp - Rp Rp - Rp -

Page 24 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

26 Ball Valve; min. seat rating 1500# CWP; F-Bore; Floating ball; Scrd /SW; BB; Replaceable ball & seats; 3/4" #800 40 EA - US$ Rp - US$ Rp -
ASTM A105; HD Galv.; 316SS ball & stem; LO; Reinforced Viton seats; API 608; API 598; API 607.

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; Hot
27 dipped galvanized; ASTM A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or 1' #150 5 EA - US$ Rp - US$ Rp -
reinforced Viton Seats; Floating ball; LO; API 6D; API 6FA..

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; Hot
28 dipped galvanized; ASTM A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or 1 1/2' #150 1 EA - US$ Rp - US$ Rp -
reinforced Viton Seats; Floating ball; LO; API 6D; API 6FA..

Ball Valve; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; ASTM A216 WCB; Hot
29 dipped galvanized; ASTM A105 + 3 mils ENP ball & seat; AISI 4140 Stem; Teflon or reinforced Teflon or 2" #150 15 EA - US$ Rp - US$ Rp -
reinforced Viton Seats; Floating ball; LO; API 6D; API 6FA..

Total 4 Rp US$ Rp -

5 PEKERJAAN ELEKTRIKAL - - - -
1 TRANSFORMER 1 SET Rp - Rp Rp - Rp -
Immerssed Oil Transformer 20kV/400V, 250 kVA, 50 Hz.
Outdoor Installation including Power Panel and Accessories, IP56.
As per indicate on Data Sheet Transformer no. PLG-DSH-030-001-A4 and Single Line Diagram

2 MV SWITCHGEAR
Outgoing VCB 630 A 1 SET - US$ Rp - US$ Rp -
20 kV, 3-phase, 50 Hz, 630 A, 25 kA, 3 wire, 3ph Metal Clad, IP 31, withdrawable
motorized include type protection relay device and accessories
As per indicate on Data sheet no. PLG-DSH-030-003-A4 and Single Line Diagram

3 LV SWITCHGEAR/ MCC
Consist of :
a - Incoming ACB 500 A (from transformer) 1 SET - US$ Rp - US$ Rp -
400 V, 3-phase, 4 wires, 50 Hz, 25 kA, Metal Clad, IP 42, withdrawable
motorized, complete set relay protection and accessories
b - Incoming ACB 500 A (from DEG) 1 SET inlcude di point a - inlcude di point a - - - -
400 V, 3-phase, 4 wires, 50 Hz, 25 kA, Metal Clad, IP 42, withdrawable
motorized, Auto Transfer Switch (ATS) as outgoing as per single line diagram, complete set relay
protection and accessories
- Outgoing
c a. DOL starter (for Jockey Pump and Water Pit Pump), 400 V, 2 Unit - US$ Rp - US$ Rp -
Include MCCB and accessories - - - - - - -
d b. Feeder Include MCCB and accessories (To VSD, DP, etc.) 10 Unit inlcude di point c - inlcude di point c - - - -
e c. Feeder Include MCCB and accessories (Spare) 4 Unit inlcude di point c - inlcude di point c - - - -

4 - VSD PANEL
VSD (Variable Speed Drive) for LPG Truck filling pump, 400 V, 45 kW, Include MCCB and accessories 2 Unit - US$ Rp - US$ Rp -

5 DISTRIBUTION PANEL
a PDB-01, 400 V, 3Ph, 4 Wire, 50Hz, 25 kW, 10 KA 1 Unit Rp - Rp Rp - Rp -
Indoor used (IP 31), Wall Mounting, Plug in Type MCCB for incoming
c/w Surge Arrester,Voltmeter, Amperemeter & Indicating Lights (for each phase) for Incoming,
Incoming
- 1ea - MCCB 63A
Outgoing
- 20ea - MCB/ELCB 10A

b PDB-02, 400 V, 3Ph, 4 Wire, 50Hz, 10 kW, 10 KA 1 Unit Rp - Rp Rp - Rp -


Outdoor used (IP 55), Wall Mounting, Plug in Type MCCB for incoming, c/w Photocell circuit and HOA,
c/w Surge Arrester,Voltmeter, Amperemeter & Indicating Lights (for each phase) for Incoming,
Incoming
- 1ea - MCCB 20A
Outgoing
- 20ea - MCB/ELCB 10A

c DBMOV-01, 400 V, 3Ph, 4 Wire, 50Hz, 15 kW, 16 KA 1 Unit Rp - Rp Rp - Rp -

Page 25 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

Outdoor used (IP 55), Wall Mounting, Plug in Type MCCB for incoming
c/w Surge Arrester,Voltmeter, Amperemeter & Indicating Lights (for each phase) for Incoming,
Incoming
- 1ea - MCCB 32A
Outgoing
- 15ea - MCB 10A

6 UPS 1 SET - US$ Rp - US$ Rp -


1 set UPS Consist of :
- 1 set : 20 kVA Uniterruptible Power Supply, Industrial type, UPS system single with By Pass System package,
400V, 3-phase, 50hz input voltage, 1-phase 220V, 50 hz output with,
Type battery VRLA, 30 minute backup time 1 x 100%, including UPS Distribution Panel
UPS shall be indoor, IP 42 installed in air conditioned room, c/w accessories
and,
- 1 set : 5 kVA UPS DC , pf 0.8. Input 220V, 3ph, 4W, 50Hz, Output: 110 VDC.
including UPS Distribution Panel, UPS shall be indoor, IP 42 installed in air conditioned room,
c/w accessories

7 CAPACITOR BANK
Capacitor Bank 50 kVAR, 400 V, 50 Hz, 3Ph, 3W indoor, IP 42, Natural Cooling, c/w power factor 1 Unit - US$ Rp - US$ Rp -
regulator, Internal Fuse Element and accessories

8 LOCAL CONTROL SWITCH


a Increased safety type, Push Button (Start/Stop), Hand - Off - Auto selectors switch with pad-lockable 2 Unit - US$ Rp - US$ Rp -
at Stop position, Indication, 1 Hub M25, Ammeter. (for LPG Filling Truk Pump)
b Weather proof, IP 55, Push Button (Start/Stop), Hand - Off - Auto selectors switch with pad-lockable 2 Unit - US$ Rp - US$ Rp -
at Stop position, Indication, 1 Hub M25, Ammeter. (for Jockey Pump and Water Pit Pump)

9 DIESEL ENGINE GENERATOR


250 kVA Genset with 400V, 3 Phase, 50Hz, 0.8 PF output, 1 Unit - US$ Rp - US$ Rp -
Indoor Installation, IP 42, continues, c/w silencer, LCP, include ATS-AMF c/w accecories
As per indicate on DEG Data Sheet no. PLG-DSH-030-002-A4.

10 OUTDOOR LIGHTING
a Floodlight High Pressure Sodium Pole Mounted, 400 watt, 220 VAC, 50 Hz, Stainless Steel 8 Unit Rp - Rp Rp - Rp -
Lumen Fixture min 55500, front Glass Retaining ring with, high Power Ballast, Lamp, impact,
Resistant Temperature, front Glass
U-Shaped Mounting Bracket made of Pivots around Floodlight axis (infinitely adjustable).
Completed with lighting pole, 10000 mm Height, JB and accessories
b Street Light High Pressure Sodium Pole Mounted (4 inch), 250 watt/HSE, 220 VAC, 50 Hz, 13 Unit Rp - Rp Rp - Rp -
Lumen Per Fixture min 29000, with, high Power Ballast, (Without External Reflector)
Completed with lighting pole 7000 mm Height, JB and accessories.
c Stanchion lighting, HPS 100 watt, 220 VAC, 50 Hz, pole mounted, 3 mm Height. 5 Unit Rp - Rp Rp - Rp -
(Ex'e', Zone 2)

11 INDOOR LIGHTING
a Fluorescent Lighting Fixtures, 2 x 36 W, 230 V, 50 Hz, IP41, 1Ph, General Type, with Clear Polycarbonate 20 Unit Rp - Rp Rp - Rp -
Cover and Reflector, c/w M20 Plugged Cable Entry Lamp & control gear, Industrial type, Recessed ceilling
mounting
b Fluorescent Lighting Fixtures, 2 x 36 W, 230 V, 50 Hz, IP41, 1Ph, General Type, with Clear Polycarbonate 5 Unit Rp - Rp Rp - Rp -
Cover and Reflector, c/w M20 Plugged Cable Entry Lamp & control gear, Industrial type, Pendant
mounting
c Fluorescent Lighting Fixtures, 2 x 36 W, 230 V, 50 Hz, IP41, 1Ph, Increased safety, Zone 2, Ex'e', 25 Unit Rp - Rp Rp - Rp -
General Type, with Clear Polycarbonate, Cover and Reflector, c/w M20 Plugged Cable Entry Lamp &
control gear, Industrial type, Pendent mounting
d Down light, 1x18 W, 230 V, 50 Hz, Ceiling mounted 5 Unit Rp - Rp Rp - Rp -
e Receptacle, Flush Mounted, General Purpuse indoor type, 230 V, 1 P, 20A, 400VA. 19 Unit Rp - Rp Rp - Rp -
f Receptacle, Flush Mounted, Ex'e', General Purpose indoor type, 230 V, 1 P, 20A, 400VA. 5 Unit Rp - Rp Rp - Rp -
g AC Receptacle, c/w on-off Switch, Flush Mounted, General Purpuse indoor type, 11 Unit Rp - Rp Rp - Rp -
230 V, 1P, 20 A, 400VA.
h Switch one device 1 way, Flus Mounted. 13 Unit Rp - Rp Rp - Rp -
i Switch one device 2 way, Flus Mounted. 1 Unit Rp - Rp Rp - Rp -
j Switch one device 1 way, Flus Mounted (Ex'e', Zone 2) 4 Unit Rp - Rp Rp - Rp -
k Switch one device 2 way, Flus Mounted (Ex'e', Zone 2) 1 Unit Rp - Rp Rp - Rp -

Page 26 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

12 AIR CONDITIONING & EX-HAUST


a Exhaust Fan,40 W- 220 VAC, 1-ph, 50 Hz, 10 " Blade - Industrial Type 6 Unit Rp - Rp Rp - Rp -
b Split Air Conditioner 1 PK, 230V, 1 ph, 50 Hz, Inverter Compressor 5 Unit Rp - Rp Rp - Rp -
c Split Air Conditioner 2 PK, 230V, 1 ph, 50 Hz, Inverter Compressor 1 Unit Rp - Rp Rp - Rp -

13 POWER CABLE
a 3c - 35 mm2, 12/24 kV, Type N2XSERY, (XLPE/SWA/PVC/Cu). 260 M Rp - Rp Rp - Rp -
b 4c - 185 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 600 M Rp - Rp Rp - Rp -
c 4c - 95 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 228 M Rp - Rp Rp - Rp -
d 4c - 35 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 300 M Rp - Rp Rp - Rp -
e 4c - 25 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 72 M Rp - Rp Rp - Rp -
f 4c - 10 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 180 M Rp - Rp Rp - Rp -
g 3c - 70 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 506 M Rp - Rp Rp - Rp -
h 3c - 10 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 252 M Rp - Rp Rp - Rp -
i 3c - 4 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 270 M Rp - Rp Rp - Rp -
j 2c - 16 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 240 M Rp - Rp Rp - Rp -
k 2c - 10 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 192 M Rp - Rp Rp - Rp -
l 2c - 6 mm2, 0.6/1 kV, Type N2XRY, (XLPE/SWA/PVC/Cu). 192 M Rp - Rp Rp - Rp -

14 CONTROL CABLE
a 10c - 1.5 mm2, Type N2XRY, 0.6/1 kV. 432 M Rp - Rp Rp - Rp -

15 LIGHTING CABLE
INDOOR
a 3c - 2.5 mm2, Type N2XRY, 0.6/1 kV 456 M Rp - Rp Rp - Rp -

OUTDOOR
a 3c - 2.5 mm2, Type N2XRY, 0.6/1 kV 672 M Rp - Rp Rp - Rp -
b 4c - 4 mm2, Type N2XRY, 0.6/1 kV 588 M Rp - Rp Rp - Rp -
c 4c - 6 mm2, Type N2XRY, 0.6/1 kV 384 M Rp - Rp Rp - Rp -
d 4c - 10 mm2, Type N2XRY, 0.6/1 kV 288 M Rp - Rp Rp - Rp -

16 GROUNDING CABLE
(0.45/0.75 kV, Cu/PVC/SWA/PVC)
1C-70 mm² 1,311 M Rp - Rp Rp - Rp -

17 GROUND ROD
a 3/4" Dia, 3m Long Ground Rod Copper Clad Steel (for Grounding) 23 EA Rp - Rp Rp - Rp -
b 3/4" Dia, 3m Long Ground Rod Copper Clad Steel (for Lightning) 5 EA Rp - Rp Rp - Rp -

18 CABLE GLAND
Cable Gland Industrial Type made of Nickle & Plate brass.
Completed with heat shrink tube.
a M20 12 EA Rp - Rp Rp - Rp -
b M25 24 EA Rp - Rp Rp - Rp -
c M32 12 EA Rp - Rp Rp - Rp -
d M63 7 EA Rp - Rp Rp - Rp -

Cable Gland Industrial Type made of Nickle & Plate brass , Suitable for Hazardous area zone 2, T3, Ex'e
Completed with heat shrink tube.
a M32 2 EA Rp - Rp Rp - Rp -

19 BULK MATERIAL
Cable Shoe (Spring Washer, Flat Washer and Blue Plastic Cap, with size as below)
a 1,5 mm² 96 EA Rp - Rp Rp - Rp -
b 4.0 mm² 7 EA Rp - Rp Rp - Rp -
c 6.0 mm² 5 EA Rp - Rp Rp - Rp -
d 10.0 mm² 60 EA Rp - Rp Rp - Rp -
e 16.0 mm² 24 EA Rp - Rp Rp - Rp -
f 25.0 mm² 34 EA Rp - Rp Rp - Rp -
g 35.0 mm² 10 EA Rp - Rp Rp - Rp -
h 35.0 mm² (For MV Cable) 14 EA Rp - Rp Rp - Rp -
i 150.0 mm² 10 EA Rp - Rp Rp - Rp -
j 185.0 mm² 19 EA Rp - Rp Rp - Rp -

Page 27 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

20 LIGHTNING PROTECTION
a Lightning Protection " E-F" Carrier System. 1 EA Rp - Rp Rp - Rp -
b Lightning Protection " Coventional" System. 4 EA Rp - Rp Rp - Rp -

21 LIGHTNING POLE
a Lightning Protection Pole Octagonal Hot Dip Galvanizized 22000 mm Height. 1 EA Rp - Rp Rp - Rp -
b Lightning Protection " Coventional" System. 4 EA Rp - Rp Rp - Rp -

22 CABLE TRAY C/W COVER


Thickness : 2 mm, Material : Sheet Steel, Finishing : Hot Dipped Galvanized
Perforated Galvanized Cable Tray 300W x 300H x 100D, 3000 m 48 EA Rp - Rp Rp - Rp -

23 HORIZONTAL TEE C/W COVER


Thickness : 2 mm, Material : Sheet Steel, Finishing : Hot Dipped Galvanized
Perforated Galvanized Cable Tray 300W x 300H x 100D, 3000 m 3 EA Rp - Rp Rp - Rp -

24 HORIZONTAL ELBOW C/W COVER


Thickness : 2 mm, Material : Sheet Steel, Finishing : Hot Dipped Galvanized
Perforated Galvanized Cable Tray 300W x 300H x 100D, 3000 m 3 EA Rp - Rp Rp - Rp -

25 OUTSIDE RISER C/W COVER


Thickness : 2 mm, Material : Sheet Steel, Finishing : Hot Dipped Galvanized
Perforated Galvanized Cable Tray 300W x 300H x 100D, 3000 m 4 EA Rp - Rp Rp - Rp -

26 INSIDE RISER C/W COVER


Thickness : 2 mm, Material : Sheet Steel, Finishing : Hot Dipped Galvanized
Perforated Galvanized Cable Tray 300W x 300H x 100D, 3000 m 1 EA Rp - Rp Rp - Rp -

27 JOINT SET
Joint set, Complete With 6ea Bolt, Nuts & Washers 316 SS. 115 EA Rp - Rp Rp - Rp -

28 SUPPORT
Steel angle 50 mm x 50 mm x 6thk, 6000 mm 72 EA Rp - Rp Rp - Rp -

29 STEEL PLATE
Steel Plate Carbon Steel ASTM A36 with size as below :
2400 x 1200 x 6 thk 10 EA Rp - Rp Rp - Rp -

30 STEEL CONDUIT
All Steel Conduit & Accessories material, complie with ANSI 801/80.5
(IEC 60614/61084/61035) with Galvafroid Metalic Paint, Threaded Conduit Joint and screw covers
Shall be coated with an electrically conductive,.
a 3/4 " Diameter (Length 3200 mm) Rigid Steel Conduit, 17 EA Rp - Rp Rp - Rp -
Hot Dip Galvanized, Complies.
b 3/4 " Diameter (Length 3200 mm) PVC Conduit, 152 EA Rp - Rp Rp - Rp -

31 FLEXIBLE CONDUIT
3/4" Flexible Conduit, Liquit Tight Galvanized strong steel strip helically wound 24 EA Rp - Rp Rp - Rp -
with nylon sealing cord heavy duty flexible PVC covered, water tight seal, UL A2066
bonded liquit tight in size 3/4" IEC 529.

32 CONDUIT FITTING
3/4" PVC "TE" 305 EA Rp - Rp Rp - Rp -

33 ELECTRICAL CABLE TAPE


a Electrical Vinyl Insulation Tape Red Colour. 18 Roll Rp - Rp Rp - Rp -
b Electrical Vinyl Insulation Tape Black Colour. 18 Roll Rp - Rp Rp - Rp -
c Electrical Vinyl Insulation Tape Blue Colour. 18 Roll Rp - Rp Rp - Rp -
d Electrical Vinyl Insulation Tape Yellow Colour. 18 Roll Rp - Rp Rp - Rp -
e Electrical Vinyl Insulation Tape Green Colour. 18 Roll Rp - Rp Rp - Rp -

34 CABLE TIES
Fully Coated Stainless Steel 316 SS Cable Ties.
a 4.6 mm (w) x 201 mm (L) 240 EA Rp - Rp Rp - Rp -
b 4.6 mm (w) x 362 mm (L) 240 EA Rp - Rp Rp - Rp -

Page 28 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

c 4.6 mm (w) x 521 mm (L) 120 EA Rp - Rp Rp - Rp -


d Sealing Compound. 18 Pack Rp - Rp Rp - Rp -

Total 5 Rp US$ Rp -

6 PEKERJAAN INSTRUMENT
A CONTROL SYSTEM 1 Ls - US$ Rp - US$ Rp -
1 PC (CPU, MONITOR 24 inch, KEYBOARD AND MOUSE) :
- OPERATOR WORKSTATION 2 EA - Include - - - - -
- ATG (AUTOMATIC TANK GAUGING) 1 EA - Include - - - - -
- TAS AND PCS SYSTEM 1 EA - Include - - - - -
- SUPERVISOR ENGINEERING 1 EA - Include - - - - -
2 LED MONITOR 42 inch with BRACKET 2 EA - Include - - - - -
3 VIDEO SWITCHER 1 EA - Include - - - - -
4 COLOR LASER PRINTER 1 EA - Include - - - - -
5 DOT MATRIX PRINTER 1 EA - Include - - - - -
6 DUAL HOMING SWITCH 2 EA - Include - - - - -
7 ROUTER WITH FIREWALL 1 EA - Include - - - - -
8 REDUNDANT NETWORK SWITCH 2 EA - Include - - - - -
9 SERVER : - - - - - - -
- TAS 2 EA - Include - - - - -
- INVENTORY 1 EA - Include - - - - -
- HISTORIAN 2 EA - Include - - - - -
- GATEAWAY 1 EA - Include - - - - -
10 KVM SWITCH 1 EA - Include - - - - -
11 MONITOR (17 inch) 1 EA - Include - - - - -
12 KEYBOARD 1 EA - Include - - - - -
13 MOUSE 1 EA - Include - - - - -
14 PLC PROCESS REDUNDANT : 1 Ls - Include - - - - -
- CONTROLLER
- INTERFACE MODULE
- ANALOG INPUT (AI) MODULE
- ANALOG OUTPUT (AO) MODULE
- DIGITAL INPUT (DI) MODULE
- DIGITAL OUTPUT (DO) MODULE
- COMMUNICATION MODULE
- POWER SUPPLY
- RAIL
15 PLC SAFETY REDUNDANT : 1 Ls - Include - - - - -
- CONTROLLER
- INTERFACE MODULE
- ANALOG INPUT (AI) MODULE
- ANALOG OUTPUT (AO) MODULE
- DIGITAL INPUT (DI) MODULE
- DIGITAL OUTPUT (DO) MODULE
- COMMUNICATION MODULE
- POWER SUPPLY
- RAIL
16 SURGE ARRESTER 20 EA - Include - - - - -
17 MOV CONTROLLER 1 Ls - Include - - - - -
18 ATG CONTROLLER INCLUDE RS-485 COMM, MODULE TO PCS 1 Ls - Include - - - - -
19 FIRE ALARM CONTROLLER 1 Ls - Include - - - - -
20 DESK 6 EA - Include - - - - -
21 CHAIR 6 EA - Include - - - - -
22 SERVER CABINET 1 Ls - Include - - - - -
23 PCS CABINET include MARSALLING 1 Ls - Include - - - - -
24 SCS CABINET include MARSALLING 1 Ls - Include - - - - -
25 MOV & ATG CABINET 1 Ls - Include - - - - -
26 ETHERNET CABLE (1 ROLL = 300 m ) 2 ROLL - Include - - - - -
27 VIDEO CABLE HDMI 2 SET - Include - - - - -
28 FINGER PRINT 2 EA Include

Page 29 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

29 PROXIMITY CARD READER 2 EA Include


30 SIS PLC REMOTE I/O : 1 LOT - US$ Rp - - US$ Rp -
- CONTROLLER
- INTERFACE MODULE
- DIGITAL INPUT (DI) MODULE
- DIGITAL OUTPUT (DO) MODULE
- COMMUNICATION MODULE
- POWER SUPPLY
- EX. PROOF CABINET
- 1 SET FO CONVERTER
- RAIL

B MTO - INSTRUMENT HOOK-UP


1 Ball valve Tube conn. 1/2" NPT-F, 316 SS Swagelok #SS-62TS6 or Equal 14 EA Rp - Rp Rp - Rp -
2 Multiport Gauge Valve 316 SS, 3/4" NPTM X 1/2" NPT-F Connection 46 EA Rp - Rp Rp - Rp -
3 1/2" NPT, Bleed Valve, 316 SS 46 EA Rp - Rp Rp - Rp -
4 1/2" NPT-F 2-Way Manifold Valve, 316 SS 8 EA Rp - Rp Rp - Rp -
5 1/2" NPT-F 5-Way Manifold Valve, 316SS 6 EA Rp - Rp Rp - Rp -
6 1/2" NPT-M Plug, 316 SS 53 EA Rp - Rp Rp - Rp -
7 1/2" NPT Hex Head Plug, HAZARDOUS AREA CLASSIFICATION 8 EA Rp - Rp Rp - Rp -
8 1/2" OD x 0.049" wt, Tubing seamless fully annealed, 316 SS 3500 Psig (max) 180 M Rp - Rp Rp - Rp -
9 Male Connector, 1/2" OD x 1/4" NPT-M, 316 SS c/w Double Ferrule Swagelok or Equal 7 EA Rp - Rp Rp - Rp -
10 Male Connector, 1/2" OD x 1/2" NPT-M, 316 SS c/w Double Ferrule Swagelok or Equal 35 EA Rp - Rp Rp - Rp -
11 Male Connector, 1/2" OD x 3/4" NPT-M, 316 SS c/w Double Ferrule Swagelok or Equal 20 EA Rp - Rp Rp - Rp -
12 1/2" OD Union Tube, 316 SS c/w Double Ferrule 14 EA Rp - Rp Rp - Rp -
13 3/4" NPT-F Pipe Union, 316 SS 14 EA Rp - Rp Rp - Rp -
14 1/2", 3" Hex Long Nipple, 316 SS 12 EA Rp - Rp Rp - Rp -
15 3/4", 3" Hex Long Nipple, 316 SS 14 EA Rp - Rp Rp - Rp -
16 3/4" OD x 1/2" NPTM, Hex Reducing Nipple, CS 14 EA Rp - Rp Rp - Rp -
17 1/2" TOD Female 7 EA Rp - Rp Rp - Rp -
18 Drain Port 2" NPTF On 4" Thru 10", 1 1/4" NPTF On 3" 2 EA Rp - Rp Rp - Rp -
19 Two Way Pneumatic PiLs, NO, 1/4" NPT Male Air Connection 2 EA Rp - Rp Rp - Rp -
20 Ejector 2 EA Rp - Rp Rp - Rp -
21 Y-Strainer 2 EA Rp - Rp Rp - Rp -
22 Ball Valve 5 EA Rp - Rp Rp - Rp -
23 Visual Indicator Assembly 2 EA Rp - Rp Rp - Rp -
- - - - - - -
C Support for Transmitter - - - - - - -
1 2" Pipe Stanchion, Sch.40, CS Galvanized 31 m Rp - Rp Rp - Rp -
2 2" Cap Pipe, Sch 40, CS Galvanized 17 EA Rp - Rp Rp - Rp -
3 Stiffener Plate 6" x 3" x 1/4", 1/4 " Thickness. CS 68 EA Rp - Rp Rp - Rp -
4 Base Plate 8" X 8" X 1/2" Thickness. CS. 17 EA Rp - Rp Rp - Rp -
5 3/8" x 1-1/2" Bolt C/W Nut & Washer. 68 EA Rp - Rp Rp - Rp -

D Support for F & G System


1 2" Pipe Stanchion, Sch.40, CS Galvanized 33 m Rp - Rp Rp - Rp -
2 2" Cap Pipe, Sch 40, CS Galvanized 18 EA Rp - Rp Rp - Rp -
3 Stiffener Plate 6" x 3" x 1/4", 1/4 " Thickness. CS 72 EA Rp - Rp Rp - Rp -
4 Base Plate 8" X 8" X 1/2" Thickness. CS. 18 EA Rp - Rp Rp - Rp -
5 3/8" x 1-1/2" Bolt C/W Nut & Washer. 72 EA Rp - Rp Rp - Rp -

E Pressure Instrument
1 Pressure Gauge 28 EA Rp - Rp Rp - Rp -
2 Pressure Switch 10 EA Rp - Rp Rp - Rp -
Page 30 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

3 Pressure Indicator Transmitter 7 EA Rp - Rp Rp - Rp -


4 Pressure Differential Transmitter 5 EA Rp - Rp Rp - Rp -

F Level Instrument
1 Level Transmitter (ATG SERVO Type) 2 EA - US$ Rp - US$ Rp -
2 Level Gauge
- Magnetic Type 2 EA - US$ Rp - US$ Rp -
- Glass Type 4 EA - US$ Rp - US$ Rp -
3 Level Switch 7 EA - US$ Rp - US$ Rp -

G Temperature Instrument
1 Temperature Gauge & Thermowell 2 EA - US$ Rp - US$ Rp -

H Instrument Valve
1 Shutdown Valve (SDV)
- Size : 10" - 300# 4 EA - US$ Rp - US$ Rp -
- Size : 6" - 300# 1 EA - US$ Rp - US$ Rp -
2 Control Valve, Size : 3" - 300# 1 EA - US$ Rp - US$ Rp -
3 Pressure Safety Valve
- Size : 6"-300# RF X 10"-150# RF 4 EA - US$ Rp - US$ Rp -
- Size : 2"-300# RF X 3"-150# RF 1 EA - US$ Rp - US$ Rp -
- Size : 1"-150# RF X 2"-150# RF 2 EA - US$ Rp - US$ Rp -
Pressure Relief Valve, Size 1" - 150# 1 EA - US$ Rp - US$ Rp -
4 Motor Operated Valve (MOV)
- Size : 3" - 300# 2 EA - US$ Rp - US$ Rp -
- Size : 4" - 300# 2 EA - US$ Rp - US$ Rp -
- Size : 6" - 300# 2 EA - US$ Rp - US$ Rp -
- Size : 10" - 300# 4 EA - US$ Rp - US$ Rp -

I Analyzer
1 Dew Point Analyzer 1 EA - US$ Rp - US$ Rp -

J Flow Instrument
1 Metering Skid
- Coriolis type skid mounted. Op. pressure 10 barg, design pressure 18 barg, temp 20 - 40°C, 1 SET - US$ Rp - US$ Rp -
Type Smart, Hart Protocol, Display LCD, Local Operator Interface, Local read out, Totalizer,
Output 4 - 20 mA (24VDC), Exp Proof/IP65/Nema 4x, Size 3"- 300# ANSI
(Tanker Loading Metering Package)
- Coriolis type skid mounted. Op. pressure 10 barg, design pressure 18 barg, temp 20 - 40°C, 1 SET - US$ Rp - US$ Rp -
Type Smart, Hart Protocol, Display LCD, Local Operator Interface, Local read out, Totalizer,
Output 4 - 20 mA (24VDC), Exp Proof/IP65/Nema 4x, Size 2"- 300# ANSI
(Tanker Loading Metering Package)
2 Flow Meter (Orifice Type) 1 EA - US$ Rp - US$ Rp -
3 Restriction Orifice 4 EA - US$ Rp - US$ Rp -

K Fire And Gas


1 Smoke Detector 4 EA - US$ Rp - US$ Rp -
2 Heat Detector 4 EA - US$ Rp - US$ Rp -
3 Gas Detector 5 EA - US$ Rp - US$ Rp -
4 Flame Detector 7 EA - US$ Rp - US$ Rp -
5 Manual Call Point 5 EA - US$ Rp - US$ Rp -
6 Beacon 5 EA - US$ Rp - US$ Rp -
7 Sirene / Audible Alarm 5 EA - US$ Rp - US$ Rp -

8 Deluge Valve 2 EA INCLUDE IN PROCESS SAFETY - - - - - -

Page 31 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

L JUNCTION BOX
TAG NO. JUNCTION BOX DIMENSION
TAG NO.
1 JB-A-01 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
2 JB-A-02 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
3 JB-A-03 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
4 JB-A-04 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
5 JB-A-05 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
6 JB-D-01 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
7 JB-D-02 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
8 JB-D-03 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
9 JB-D-04 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
10 JB-D-05 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
11 JB-D-06 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
12 JB-D-07 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -
13 JB-D-08 400mm (H) x 600 mm (L) x 150 mm (D) (VTA) 1 Ea - US$ Rp - US$ Rp -

1 Tag No. See List Bellow


2 Signal Type Analog Signal, 4-20 mA, Two and Three Wire with Individual and Overall Screen
Digital Signal, 24 VDC, Two Wire with Overall Screen
3 Material 316 SS
4 Thickness Mfr. Std
5 Door Hinged, Removable, Front Open and Lockable
6 Hinge Material 316 SS
7 Gland Plate (Bottom) 316 SS Removable with Gasket and Screws, Drilled to suit the Cable Gland
8 Bottom Entries Drilled Holes suitable for Gland c/w Temporary and Permanent Plug
9 Terminal Block Screw Type Equipped with Sequence Number c/w Plate and End Bracket, Vertical Mounting Rail
10 Terminal Size Suitable with 1 ~ 2.5 mm2
11 No. of Terminal See List, Complete with Jumper Bar for Screen / Earth Wire
12 Body Earthing Yes
13 Instrument Earthing, Bar Yes
14 Enclosure Mounting Yes, Suitable for Horizontal
15 Accessories Mounting Yes (Vendor to Specify)
16 Certification Certified Eex (d) for use in Zone 1 Group IIA, T3
Suitable for Hazardous Area
17 Weather Proof IP 56 (Minimum)
18 Dimension See List Bellow
19 Label Tag No. shall be Labelled on the Front Door (316 SS)
Cerification Number shall be Fixed as per Manufacturer Standard
20 Breather / Drain Plug To be Insttalled on Bottom of Junction Box, Certified for IP 56 (min) and Zone 1, Gr. IIA, T-3
21 No. of Cable Entries on Bottom / Size See List Bellow
22 Manufacture VTA
23 Model VTA

M Signal / Control Cable


1 Size 1 Pr x 1.5 mm2 900 m Rp - Rp Rp - Rp -
5 Pr x 1.5 mm2 240 m Rp - Rp Rp - Rp -
15 Pr x 1.5 mm2 420 m Rp - Rp Rp - Rp -
2 Service Voltage 24 VDC System
3 Insulation Grade 300 V
4 Color Wire Cable White - Black

Page 32 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

5 Conductor Material a) Cooper cable cores shall be made of circular stranded


annealed bare cooper
b) Conductors shall be 7-stranded copper wire
6 Conductor Insulation Material a) Cross Linked Polyethylene (XLPE)
b) Suitable for direct buried installation
c) Flame Retardant as per IEC 60332
d) Clearly marked at each along its length
7 Screen/Shield a) Individual screen/shield an overall screen/shield is required to prevent interferences
b) Individual screen/shield shall be 100% coverage of 1.77 mils of aluminum mylar tape and 7-stranded tinned copper drain wire.
c) Overall screen/shield shall be 100% coverage of 2.35 mils minimum of aluminum tape and 7-stranded tinned copper drain wire.
8 Outer Sheath The outer sheath material shall be Polyvinyl Chloride (PVC) containing necessary additive to meet the following characteristics
such as:
a) Flame Retardant
b) Sunlight Resistant
c) Proofed against Aliphatic Hydrocarbons
d) Low smoke zero halogen
e) Gas and vapor tight
9 Armour f) Armour shall be Steel Wire Armour (SWA) type and electrically continuous throughout the length of cable

N Power / Solenoid Cable / Digital


1 Size 2 Core x 2.5 mm2 2,100 m Rp - Rp Rp - Rp -
20 Core x 2.5 mm2 840 m Rp - Rp Rp - Rp -
30 Core x 2.5 mm2 480 m Rp - Rp Rp - Rp -
50 Core x 2.5 mm2 420 m Rp - Rp Rp - Rp -
2 Service Voltage 24 VDC System
3 Insulation Grade 600 V
4 Color Wire Cable White - Black
5 Conductor Material a) Cooper cable cores shall be made of circular stranded annealed bare cooper
b) Conductors shall be 7-stranded copper wire
6 Conductor Insulation Material a) Cross Linked Polyethylene (XLPE)
b) Suitable for direct buried installation
c) Flame Retardant as per IEC 60332
d) Clearly marked at each along its length
7 Screen/Shield a) Individual screen/shield an overall screen/shield is required to prevent interferences.
b) Individual screen/shield shall be 100% coverage of 1.77 mils of aluminum mylar tape and 7-stranded tinned copper drain wire.
c) Overall screen/shield shall be 100% coverage of 2.35 mils minimum of aluminum tape and 7-stranded tinned copper drain wire.
8 Outer Sheath The outer sheath material shall be Polyvinyl Chloride (PVC) containing
necessary additive to meet the following characteristics such as:
a) Flame Retardant
b) Sunlight Resistant
c) Proofed against Aliphatic Hydrocarbons
d) Low smoke zero halogen
e) Gas and vapor tight
9 Armour f) Armour shall be Steel Wire Armour (SWA) type and electrically continuous throughout the length of cable

O Serial Link Cable.


1 RS-485 Serial Link Cable Flame retardant as per IEC-60332 and Armoured cable, 3,396 m Rp - Rp Rp - Rp -
Grey Outer sheath.

P Fire Resistant Cable


1 2C - 2.5 mm² Armoured, Fire resistant, Mica glass, 600V, SWA, OS 1,068 m Rp - Rp Rp - Rp -
2 10C - 2.5 mm² Armoured, Fire resistant, Mica glass, 600V, SWA, OS/IS 360 m Rp - Rp Rp - Rp -
3 20C - 2.5 mm² Armoured, Fire resistant, Mica glass, 600V, SWA, OS/IS 468 m Rp - Rp Rp - Rp -
4 1T - 1.5 mm² Armoured, Fire resistant, Mica glass, 300V, SWA, OS 720 m Rp - Rp Rp - Rp -

Page 33 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

5 10T - 1.5 mm² Armoured, Fire resistant, Mica glass, 300V, SWA, OS/IS 900 m Rp - Rp Rp - Rp -

Q BULK MATERIAL
1 Cable Gland
For Steel Wire Armour Cable, Sealing component
IP 65, Eex"d", Deluge Seal Type
Suitable for hazardous area Zone 1, Gr. IIA, T-3
Size : 1/2" NPT-M 120 EA Rp - Rp Rp - Rp -
3/4" NPT-M 99 EA Rp - Rp Rp - Rp -
1" NPT-M 0 EA Rp - Rp - - - -
11/4" NPT-M 4 EA Rp - Rp Rp - Rp -
11/2" NPT-M 6 EA Rp - Rp Rp - Rp -
2" NPT-M 9 EA Rp - Rp Rp - Rp -
2 Cable Lug with Insulation
For Field Instrument Fork Type w/ Insulator, 100 pcs/pack
Size : 1.5 mm2 3 Pack - US$ Rp - US$ Rp -
2.5 mm2 4 Pack - US$ Rp - US$ Rp -
For Junction Box & Cabinet Ferrule/Cord End Type w/ isolator , 100 pcs/pack
Size : 1.5 mm2 3 Pack - US$ Rp - US$ Rp -
2.5 mm2 4 Pack - US$ Rp - US$ Rp -
3 Cable Ties
Weather Resistant, Color Black
Size : 100 mm L x 2.5 mm - 100 pcs/pack 8 Pack - US$ Rp - US$ Rp -
200 mm L x 2.5 mm - 100 pcs/pack 8 Pack - US$ Rp - US$ Rp -
4 Cable Marker
Embose Type, Material Stainless Steel
Size : 20 mm (W) x 100 mm (L) 324 EA - US$ Rp - US$ Rp -
5 PVC Tube Wire Marker
PVC Tube White Color for Hot Marker (100 m/RolI)
Size : 100 mm L 2 Roll - US$ Rp - US$ Rp -
200 mm L 2 Roll - US$ Rp - US$ Rp -
6 Cable Route Marker
Stainless Steel Route Marker
Size : 100 mm (L) x 100 mm (W)
Straight Point 64 EA - US$ Rp - US$ Rp -
90 deg Point 8 EA - US$ Rp - US$ Rp -
"T" Branch Point 3 EA - US$ Rp - US$ Rp -
7 Sealing Compound
Sealing Compound for Instrument Cable Seal, Outdoor Type (1Kg / Pack) 3 Pack - US$ Rp - US$ Rp -
8 Concrete Tile
Pre Cast Block for Cable Marker 74 EA - US$ Rp - US$ Rp -
Size : 200 mm L x 150 mm L x 50 mm D
9 Warning Tape
Plastic, Yellow & Black Color 4 Roll - US$ Rp - US$ Rp -
10 Rigid Steel Conduit
Material : Steel 3000 mm(L)
Size : 1" NPT-M 6 EA - US$ Rp - US$ Rp -
2" NPT-M 3 EA - US$ Rp - US$ Rp -
12 Conduit Saddle/Clamp c/w Bolt & Nut
Material : Steel
Size : 1" NPT-M 164 EA - US$ Rp - US$ Rp -
2" NPT-M 11 EA - US$ Rp - US$ Rp -

Q Cable Tray
Material Hot Dip Galvanized
1 Straight tray complitly with cover
Size Size : 150mm (W) x 50 mm (D) x 3000mm (L) x 2 Thickness 54 EA Rp - Rp Rp - Rp -

2 Horisontal Tee Tray complitly with cover Size : 150 mm (W) x 50 mm (D) x 2 Thickness 12 EA Rp - Rp Rp - Rp -

3 Radius Elbow 90° Tray complitly with cover Size : 150 mm (W) x 50 mm (D) x 2 Thickness 12 EA Rp - Rp Rp - Rp -

4 Vertical Riser Tray complitly with cover

Page 34 of 52
BILL OF QUANTITY
PEMBANGUNAN TANGKI TIMBUN DI DEPOT LPG PULAU LAYANG KAP. 2 x 1500 DWT
1 US$ = Rp 13.028,-

Rev-1
1 US$ = Rp.
HARGA SATUAN TOTAL HARGA
VOLUME MATERIAL JASA MATERIAL JASA
No JENIS PEKERJAAN SAT
TOTAL
(X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$ (X Rp. 1.000) US.$

- Vertical Inside Riser 90° Tray Size : 150 mm (W) x 50 mm (D) x 2 Thickness 12 EA Rp - Rp Rp - Rp -

- Vertical Outside Riser 90° Tray Size : 150 mm (W) x 50 mm (D) x 2 Thickness 12 EA Rp - Rp Rp - Rp -

5 Reducer Right Hand Tray complitly with cover Size : 150 mm(W1) x 50 mm(W2) x 50 mm (D) x 2 Thickness 12 EA Rp - Rp Rp - Rp -

R Cable Tray Accessories


1 Cover Clamp c/w Bolt & Nut
Size : 150 mm (W) x 50 mm (D) x 2 Thickness 114 EA Rp - Rp Rp - Rp -
2 Splice Plate for Stand
Size : 150 mm(H) x 2 Thickness. c/w Bolt & Nut 114 EA Rp - Rp Rp - Rp -
3 Jointing Plate
Size : 150 mm(H) x 2 Thickness. c/w Bolt & Nut 60 EA Rp - Rp Rp - Rp -
-
-
Total 6 Rp US$ Rp -

7 PEKERJAAN PROCESS SAFETY

1 FIRE MONITOR FLOW RATE CAPACITY : 500 gpm(1892 l/min) 4 SET Rp - Rp Rp - Rp -


SYSTEM MANUAL
ELEVATION ANGLE : 360 degree

2 FIRE HYDRANT / HYDRANT PILAR FLOW RATE PER HYDRANT : 250 gpm(946.4 l/min) 6 UNIT Rp - Rp Rp - Rp -
SYSTEM MANUAL
C/w House cabinet, water nozzel, fire hose
3 DELUGE SYSTEM DELUGE VALVES 8 inch, ANSI 150 FF 2 SET Rp - Rp Rp - Rp -
AUTOMATIC SYSTEM

4 WATER SPRAY NOZZLE Effective Spraying Range 0.7 - 2 m (axial distance) 268 EA Rp - Rp Rp - Rp -
Coverage Area 2 m (radial distance)

5 DRY CHEMICAL
Portable Dry Chemical Powder 9 kg 3 EA Rp - - Rp - - -
Portable CO2 9 kg 4 EA Rp - - Rp - - -
Powder Wheels 63 kg 3 EA Rp - - Rp - - -
-
Total 7 - Rp - Rp -

8 PEKERJAAN INSPEKSI, TESTING, & COMMISSIONING


1 INSPECTION
FACTORY ACCEPTANCE TEST 1 Ls - - Rp - - Rp -
2 TESTING
NDT TEST (UNTUK TANGKI & PIPING SYTEM) 1 Ls - - Rp - - Rp -
HYDROSTATIC TEST (UNTUK TANGKI & PIPING SYTEM) 1 Ls - - Rp - - Rp -
KALIBRASI (UNTUK SEMUA ALAT UKUR-INSTRUMENT TERKAIT)
N2 PURGING (UNTUK TANGKI & PIPING SYSTEM) 1 Ls - - Rp - - Rp -
PDA TEST 3 Titik - - Rp - - Rp -
3 PWHT UNTUK SPERICAL TANK 1 Ls - - Rp - - Rp -
4 MECHANICAL COMPLETION, START-UP & COMMISSIONING 1 Ls - - Rp - - Rp -

Total 8 - - Rp -

9 TRAINING 1 Ls - - Rp - - Rp -

Total 9 - - Rp -
- -
10 PENYIAPAN DOKUMEN PENDUKUNG SERTIFIKASI SKPP & SKPI 1 Ls - - Rp - - Rp -

Total 10 - - Rp -

Page 35 of 52
REKAP ANALISA HARGA SATUAN PIPING
PRICE SCHEDULE
PEKERJA UPAH Rp/
FOREMAN MANHOURS 102,920.00 Pekerja JURNAL EDISI XXXIV 2015 Hal 489
PIPE WELDER MANHOURS 121,230.00 Tukang JURNAL EDISI XXXIV 2015 Hal 489
GRINDER MANHOURS 139,574.00 Kepala Tukang JURNAL EDISI XXXIV 2015 Hal 489
PIPE FITTER MANHOURS 157,901.00 Mandor JURNAL EDISI XXXIV 2015 Hal 489
H/E OPERATOR MANHOURS
RIGGER MANHOURS
HELPER MANHOURS
X-TRAY TECHNICIAN MANHOURS
PAINTER MANHOURS

MATERIAL HARGA SATUAN


Kwt. Las 6010 101,750.00 Kg.
Kwt. Las 7010 101,750.00 Kg.
Oxygen 77,000.00 Kg.
Acetylene 302,500.00 Kg.
Grind Disc 11,000.00 Buah
Rotary & Cup Brush 66,000.00 Buah
Fuel 10,945.00 Liter
Fuel diesel 10,945.00 Liter
FILM D7 (4 X 10") 70,000.00 SHEET Lumpsump Price Min 40 sheet PT. Wismar
FILM D7 (4 X 15") 80,000.00 SHEET Lumpsump Price Min 40 sheet PT. Wismar
Team Equipment & acomodation 2,500,000.00 Hari
FILM D7 (4 X 10") D 60,000.00 SHEET
FILM D7 (4 X 15") D 70,000.00 SHEET
Foam Pig 2,950,850.00 Buah
Inhibitor 200,000.00 Buah
Water 12,550 m3 http://www.pamjaya.co.id/pages/info-pelanggan/tarif-air-minum
Meni Besi 13,001.80 Kg
Kuas 7,700.00 Bh
Cat dasar 24,465.00 Kg
Cat Penutup 137,500.00 Kg
Ampelas 6,716.00 lbr
Minyak Cat 23,467.00 ltr
Nitrogen 28,333 M3 http://candrabayugas.com/layanan/

PERALATAN BIAYA

Pick up 550,000 (Rp/hari)


Scafolding 852,000 (Rp/hari)
Crane 20 Ton 2,000,000 (Rp/hari)
Mesin Las 400A 201,666.67 (Rp/hari)
Mesin Gerinda 20,000.00 (Rp/hari) Beli baru Rp 600000 untuk 30 hari
Pick up 550,000.00 (Rp/hari)
Clamp Pipa 22,000.00 (Rp/hari)
Tripod 70,000.00 (Rp/hari) Beli baru Rp. 2,100,000 untuk 30 hari
Sling Belt 16,666.67 (Rp/hari) Beli baru Rp. 500,000 untuk 30 hari
Alat Radio Isotop 300,000.00 (Rp/hari)
Hiab Crane 1,050,000.00 (Rp/hari)
Fill In Pump 1,500,000.00 (Rp/hari)
High Pressure Pump 2,000,000.00 (Rp/hari)
Compressor 1,430,000.00 (Rp/hari)
Genset 55 KVA 2,500,000.00 (Rp/hari)
Chain Blok 5 T 53,333.33 (Rp/hari) Harga Rp 1,600,000 untuk 30 hari
Barton chart recorder 2,500,000.00 (Rp/hari)
Pick up 550,000.00 (Rp/hari)

W. 1 WELDING
DIA PIPA 16 " scd 40 53,803.55
MANHOUR PER EACH 11.20
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 1.12 -
PIPE FITTER 0.45 5.04 -
PIPE WELDER 0.20 2.24 -
H/E OPERATOR 0.05 0.56 -
RIGGER 0.10 1.12 -
HELPER 0.10 1.12 -

MATERIAL
Kwt. Las 6010 1.34 101,750.00 136,151.42

Page 36 of 52
Kwt. Las 7010

PERALATAN
Mesin Las 400A 2.24 201,666.67 451,733.33
Clamp Pipa 1.12 22,000.00 24,640.00
Tripod 1.12 70,000.00 78,400.00
Mesin Gerinda 1.12 20,000.00 22,400.00

BAHAN (Habis Pakai)


Grind Disc 1.12 11,000.00 12,320.00
Rotary & Cup Brush 1.12 66,000.00 73,920.00
Fuel 5.60 10,945.00 61,292.00
860,856.75
W. 1 WELDING
DIA PIPA 12 " scd 40 52,676.28
MANHOUR PER EACH 8.10
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.81 -
PIPE FITTER 0.45 3.65 -
PIPE WELDER 0.20 1.62 -
H/E OPERATOR 0.05 0.41 -
RIGGER 0.10 0.81 -
HELPER 0.10 0.81 -

MATERIAL
Kwt. Las 6010 1.06 101,750.00 107,998.08
Kwt. Las 7010

PERALATAN
Mesin Las 400A 1.62 201,666.67 326,700.00
Clamp Pipa 0.81 22,000.00 17,820.00
Tripod 0.81 70,000.00 56,700.00
Mesin Gerinda 0.81 20,000.00 16,200.00

BAHAN (Habis Pakai)


Grind Disc 0.81 11,000.00 8,910.00
Rotary & Cup Brush 0.81 66,000.00 53,460.00
Fuel 4.05 10,945.00 44,327.25
632,115.33

W. 2 WELDING
DIA PIPA 10 " scd 40
MANHOUR PER EACH 6.90
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.69 -
PIPE FITTER 0.45 3.11 -
PIPE WELDER 0.20 1.38 -
H/E OPERATOR 0.05 0.35 -
RIGGER 0.10 0.69 -
HELPER 0.10 0.69 -

MATERIAL
Kwt. Las 6010 0.45 101,750.00 45,829.95
Kwt. Las 7010

PERALATAN
Mesin Las 400A 1.38 201,666.67 278,300.00
Clamp Pipa 0.69 22,000.00 15,180.00
Tripod 0.69 70,000.00 48,300.00
Mesin Gerinda 0.69 20,000.00 13,800.00

BAHAN (Habis Pakai)


Grind Disc 0.69 11,000.00 7,590.00
Rotary & Cup Brush 0.69 66,000.00 45,540.00
Fuel 3.45 10,945.00 37,760.25
492,300.20

W. 3 WELDING
DIA PIPA 8 " scd 40
MANHOUR PER EACH 5.70
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.57 -

Page 37 of 52
PIPE FITTER 0.45 2.57 -
PIPE WELDER 0.20 1.14 -
H/E OPERATOR 0.05 0.29 -
RIGGER 0.10 0.57 -
HELPER 0.10 0.57 -

MATERIAL
Kwt. Las 6010 0.39 101,750.00 39,691.60
Kwt. Las 7010

PERALATAN
Mesin Las 400A 1.14 201,666.67 229,900.00
Clamp Pipa 0.57 22,000.00 12,540.00
Tripod 0.57 70,000.00 39,900.00
Mesin Gerinda 0.57 20,000.00 11,400.00

BAHAN (Habis Pakai)


Grind Disc 0.57 11,000.00 6,270.00
Rotary & Cup Brush 0.57 66,000.00 37,620.00
Fuel 2.85 10,945.00 31,193.25
408,514.85

W. 4 WELDING
DIA PIPA 6 " scd 40
MANHOUR PER EACH 4.40
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.44 -
PIPE FITTER 0.45 1.98 -
PIPE WELDER 0.20 0.88 -
H/E OPERATOR 0.05 0.22 -
RIGGER 0.10 0.44 -
HELPER 0.10 0.44 -

MATERIAL
Kwt. Las 6010 0.30 101,750.00 30,876.37
Kwt. Las 7010

PERALATAN
Mesin Las 400A 0.88 201,666.67 177,466.67
Clamp Pipa 0.44 22,000.00 9,680.00
Tripod 0.44 70,000.00 30,800.00
Mesin Gerinda 0.44 20,000.00 8,800.00

BAHAN (Habis Pakai)


Grind Disc 0.44 11,000.00 4,840.00
Rotary & Cup Brush 0.44 66,000.00 29,040.00
Fuel 2.20 10,945.00 24,079.00
315,582.04

W. 5 WELDING
DIA PIPA 4 " scd 40
MANHOUR PER EACH 3.50
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.35 -
PIPE FITTER 0.45 1.58 -
PIPE WELDER 0.20 0.70 -
H/E OPERATOR 0.05 0.18 -
RIGGER 0.10 0.35 -
HELPER 0.10 0.35 -

MATERIAL
Kwt. Las 6010 0.09 101,750.00 8,769.07

PERALATAN
Mesin Las 400A 0.70 201,666.67 141,166.67
Clamp Pipa 0.35 22,000.00 7,700.00
Tripod 0.35 70,000.00 24,500.00
Mesin Gerinda 0.35 20,000.00 7,000.00

BAHAN (Habis Pakai)


Grind Disc 0.35 11,000.00 3,850.00
Rotary & Cup Brush 0.35 66,000.00 23,100.00
Fuel 1.75 10,945.00 19,153.75

Page 38 of 52
235,239.49

W. 6 WELDING
DIA PIPA 3 " scd 40
MANHOUR PER EACH 2.60
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.26 -
PIPE FITTER 0.45 1.17 -
PIPE WELDER 0.20 0.52 -
H/E OPERATOR 0.05 0.13 -
RIGGER 0.10 0.26 -
HELPER 0.10 0.26 -

MATERIAL
Kwt. Las 6010 0.06 101,750.00 5,815.28
Kwt. Las 7010

PERALATAN
Mesin Las 400A 0.52 201,666.67 104,866.67
Clamp Pipa 0.26 22,000.00 5,720.00
Tripod 0.26 70,000.00 18,200.00
Mesin Gerinda 0.26 20,000.00 5,200.00

BAHAN (Habis Pakai)


Grind Disc 0.26 11,000.00 2,860.00
Rotary & Cup Brush 0.26 66,000.00 17,160.00
Fuel 1.30 10,945.00 14,228.50
174,050.45

W. 7 WELDING
DIA PIPA 2 " scd 40
MANHOUR PER EACH 1.80
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.18 -
PIPE FITTER 0.45 0.81 -
PIPE WELDER 0.20 0.36 -
H/E OPERATOR 0.05 0.09 -
RIGGER 0.10 0.18 -
HELPER 0.10 0.18 -

MATERIAL
Kwt. Las 6010 0.03 101,750.00 2,676.88
Kwt. Las 7010

PERALATAN
Mesin Las 400A 0.36 201,666.67 72,600.00
Clamp Pipa 0.18 22,000.00 3,960.00
Tripod 0.18 70,000.00 12,600.00
Mesin Gerinda 0.18 20,000.00 3,600.00

BAHAN (Habis Pakai)


Grind Disc 0.18 11,000.00 1,980.00
Rotary & Cup Brush 0.18 66,000.00 11,880.00
Fuel 0.90 10,945.00 9,850.50
119,147.38

W. 8 WELDING
DIA PIPA 1 " scd 40
MANHOUR PER EACH 1.20
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.12 -
PIPE FITTER 0.45 0.54 -
PIPE WELDER 0.20 0.24 -
H/E OPERATOR 0.05 0.06 -
RIGGER 0.10 0.12 -
HELPER 0.10 0.12 -

MATERIAL
Kwt. Las 6010 0.03 101,750.00 2,676.88
Kwt. Las 7010

PERALATAN
Mesin Las 400A 0.24 201,666.67 48,400.00

Page 39 of 52
Clamp Pipa 0.12 22,000.00 2,640.00
Tripod 0.12 70,000.00 8,400.00
Mesin Gerinda 0.12 20,000.00 2,400.00

BAHAN (Habis Pakai)


Grind Disc 0.12 11,000.00 1,320.00
Rotary & Cup Brush 0.12 66,000.00 7,920.00
Fuel 0.60 10,945.00 6,567.00
80,323.88

N.1 NDT TESTING


DIA PIPA 16 "
MANHOUR PER EACH 3.20 2,500,000.00
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0 32.00 Include
X-TRAY TECHNICIAN 0.60 1.38 Include
PIPE FITTER 0.10 0.23 Include
PIPE WELDER 0.05 0.11 Include
HELPER 0.15 0.35 Include

MATERIAL
FILM D7 (4 X 10")
FILM D7 (4 X 15") 5.00 80,000.00 400,000.00

PERALATAN
Alat Radio Isotop 0.46

BAHAN (Habis Pakai)

400,000.00
N.1 NDT TESTING
DIA PIPA 12 "
MANHOUR PER EACH 2.30
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.23 Include
X-TRAY TECHNICIAN 0.60 1.38 Include
PIPE FITTER 0.10 0.23 Include
PIPE WELDER 0.05 0.11 Include
HELPER 0.15 0.35 Include

MATERIAL
FILM D7 (4 X 10")
FILM D7 (4 X 15") 4.00 80,000.00 320,000.00

PERALATAN
Alat Radio Isotop 0.33 Include

BAHAN (Habis Pakai)

320,000.00

N.1 NDT TESTING


DIA PIPA 10"
MANHOUR PER EACH 2.20
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.22 Include
X-TRAY TECHNICIAN 0.60 1.32 Include
PIPE FITTER 0.10 0.22 Include
PIPE WELDER 0.05 0.11 Include
HELPER 0.15 0.33 Include

MATERIAL
FILM D7 (4 X 10")

Page 40 of 52
FILM D7 (4 X 15") 3.00 80,000.00 240,000.00

PERALATAN
Alat Radio Isotop 0.31 Include

BAHAN (Habis Pakai)

240,000.00

N.1 NDT TESTING


DIA PIPA 8"
MANHOUR PER EACH 2.10
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.21 Include
X-TRAY TECHNICIAN 0.60 1.26 Include
PIPE FITTER 0.10 0.21 Include
PIPE WELDER 0.05 0.11 Include
HELPER 0.15 0.32 Include

MATERIAL
FILM D7 (4 X 10")
FILM D7 (4 X 15") 3.00 80,000.00 240,000.00

PERALATAN
Alat Radio Isotop 0.30 Include

BAHAN (Habis Pakai)


Include

240,000.00

N.1 NDT TESTING


DIA PIPA 6"
MANHOUR PER EACH 2.00
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.20 Include
X-TRAY TECHNICIAN 0.60 1.20 Include
PIPE FITTER 0.10 0.20 Include
PIPE WELDER 0.05 0.10 Include
HELPER 0.15 0.30 Include

MATERIAL
FILM D7 (4 X 10") 3.00 70,000.00 210,000.00

PERALATAN
Alat Radio Isotop 0.29 Include

BAHAN (Habis Pakai)


Include

210,000.00

N.1 NDT TESTING


DIA PIPA 4"
MANHOUR PER EACH 2.00
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.20 Include
X-TRAY TECHNICIAN 0.60 1.20 Include

Page 41 of 52
PIPE FITTER 0.10 0.20 Include
PIPE WELDER 0.05 0.10 Include
HELPER 0.15 0.30 Include

MATERIAL
FILM D7 (4 X 10") 3.00 70,000.00 210,000.00

PERALATAN
Alat Radio Isotop 0.29 Include

BAHAN (Habis Pakai)


Include

210,000.00

N.1 NDT TESTING


DIA PIPA 3"
MANHOUR PER EACH 1.90
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.19 Include
X-TRAY TECHNICIAN 0.60 1.14 Include
PIPE FITTER 0.10 0.19 Include
PIPE WELDER 0.05 0.10 Include
HELPER 0.15 0.29 Include

MATERIAL
FILM D7 (4 X 10") 3.00 70,000.00 210,000.00

PERALATAN
Alat Radio Isotop 0.27 Include

BAHAN (Habis Pakai)


Include

210,000.00

N.1 NDT TESTING


DIA PIPA 2"
MANHOUR PER EACH 1.90
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.19 Include
X-TRAY TECHNICIAN 0.60 1.14 Include
PIPE FITTER 0.10 0.19 Include
PIPE WELDER 0.05 0.10 Include
HELPER 0.15 0.29 Include

MATERIAL
FILM D7 (4 X 10") 2.00 70,000.00 140,000.00

PERALATAN
Alat Radio Isotop 0.27 Include

BAHAN (Habis Pakai)


Include

140,000.00

Page 42 of 52
18,794,606.25

H.1 HYDRO TESTING


DIA 10.00
Panjang 1,001.42 197.82 210.66
MANHOUR PER EACH 123.17
Description compotiion MHRS Unit Unit price total
TENAGA KERJA
FOREMAN 0.10 7.00 Days -
PIPE FITTER 0.45 7.00 Days -
PIPE WELDER 0.20 7.00 Days -
H/E OPERATOR 0.05 7.00 Days -
RIGGER 0.10 7.00 Days -
HELPER 0.10 7.00 Days -

MATERIAL
Water 61.82 M3 12,550.00 775,869.76
Foam Pig - 2,950,850.00 -
Inhibitor - 200,000.00 -

PERALATAN
Hiab Crane 7.00 Days 1,050,000.00 7,350,000.00
Fill In Pump 7.00 Days 1,500,000.00 10,500,000.00
High Pressure Pump 7.00 Days 2,000,000.00 14,000,000.00
Compressor 7.00 Days 1,430,000.00 10,010,000.00
Foam Pig 7.00 Days 2,950,850.00 20,655,950.00
Barton chart recorder 7.00 Days 2,500,000.00 17,500,000.00
Pick up 7.00 Days 550,000.00 3,850,000.00
Genset 55 KVA 7.00 Days 2,500,000.00 17,500,000.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 131.25 Liter 10,945.00 1,436,531.25
Fuel Pick up 612.50 Liter 10,945.00 6,703,812.50

110,282,163.51
110,126.29

I. 1 INSTALLATION VALVE
DIA 16 "
MANHOUR PER EACH 3.90
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.39 -
PIPE FITTER 0.45 1.76 -
PIPE WELDER 0.20 0.78 -
H/E OPERATOR 0.05 0.20 -
RIGGER 0.10 0.39 -
HELPER 0.10 0.39 -

MATERIAL

PERALATAN
Tripod 0.39 70,000.00 27,300.00
Chain Blok 5 T 0.39 53,333.33 20,800.00
Hiab Crane 0.20 1,050,000.00 204,750.00

BAHAN (Habis Pakai)


Fuel Hiab Crane - 10,945.00 -

252,850.00

I. 1 INSTALLATION VALVE
DIA 12 "
MANHOUR PER EACH 2.90
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.29 -
PIPE FITTER 0.45 1.31 -
PIPE WELDER 0.20 0.58 -
H/E OPERATOR 0.05 0.15 -
RIGGER 0.10 0.29 -

Page 43 of 52
HELPER 0.10 0.29 -

MATERIAL

PERALATAN
Tripod 0.29 70,000.00 20,300.00
Chain Blok 5 T 0.29 53,333.33 15,466.67
Hiab Crane 0.15 1,050,000.00 152,250.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 18.75 10,945.00 205,218.75

393,235.42

I. 1 INSTALLATION VALVE
DIA 10 "
MANHOUR PER EACH 2.30
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.23 -
PIPE FITTER 0.45 1.04 -
PIPE WELDER 0.20 0.46 -
H/E OPERATOR 0.05 0.11 -
RIGGER 0.10 0.23 -
HELPER 0.10 0.23 -

MATERIAL

PERALATAN
Tripod 0.23 70,000.00 16,100.00
Chain Blok 5 T 0.23 53,333.33 12,266.67
Hiab Crane 0.11 1,050,000.00 120,750.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 18.75 10,945.00 205,218.75

354,335.42

I. 1 INSTALLATION VALVE
DIA PIPA 8 " scd 40
MANHOUR PER EACH 1.70
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.17 -
PIPE FITTER 0.45 0.77 -
PIPE WELDER 0.20 0.34 -
H/E OPERATOR 0.05 0.09 -
RIGGER 0.10 0.17 -
HELPER 0.10 0.17 -

MATERIAL

PERALATAN
Tripod 0.17 70,000.00 11,900.00
Chain Blok 5 T 0.17 53,333.33 9,066.67
Hiab Crane 0.09 1,050,000.00 89,250.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 18.00 10,945.00 197,010.00

307,226.67

I. 1 INSTALLATION VALVE
DIA PIPA 6 " scd 40
MANHOUR PER EACH 1.30
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.13 -
PIPE FITTER 0.45 0.59 -

Page 44 of 52
PIPE WELDER 0.20 0.26 -
H/E OPERATOR 0.05 0.07 -
RIGGER 0.10 0.13 -
HELPER 0.10 0.13 -

MATERIAL

PERALATAN
Tripod 0.13 70,000.00 9,100.00
Chain Blok 5 T 0.13 53,333.33 6,933.33
Hiab Crane 0.07 1,050,000.00 68,250.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 18.00 10,945.00 197,010.00

281,293.33

I. 1 INSTALLATION VALVE
DIA PIPA 4 " scd 40
MANHOUR PER EACH 1.10
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.11 -
PIPE FITTER 0.45 0.50 -
PIPE WELDER 0.20 0.22 -
H/E OPERATOR 0.05 0.06 -
RIGGER 0.10 0.11 -
HELPER 0.10 0.11 -

MATERIAL

PERALATAN
Tripod 0.11 70,000.00 7,700.00
Chain Blok 5 T 0.11 53,333.33 5,866.67
Hiab Crane 0.06 1,050,000.00 57,750.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 18.00 10,945.00 197,010.00

268,326.67

I. 1 INSTALLATION VALVE
DIA PIPA 3 " scd 40
MANHOUR PER EACH 0.90
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.09 -
PIPE FITTER 0.45 0.41 -
PIPE WELDER 0.20 0.18 -
H/E OPERATOR 0.05 0.05 -
RIGGER 0.10 0.09 -
HELPER 0.10 0.09 -

MATERIAL

PERALATAN
Tripod 0.09 70,000.00 6,300.00
Chain Blok 5 T 0.09 53,333.33 4,800.00
Hiab Crane 0.05 1,050,000.00 47,250.00

BAHAN (Habis Pakai)


Fuel Hiab Crane 18.00 10,945.00 197,010.00

255,360.00

I. 1 INSTALLATION VALVE
DIA PIPA 2 " scd 40
MANHOUR PER EACH 0.60
Description compotiion MHRS Unit price total

Page 45 of 52
TENAGA KERJA
FOREMAN 0.10 0.06 -
PIPE FITTER 0.45 0.27 -
PIPE WELDER 0.20 0.12 -
H/E OPERATOR 0.05 0.03 -
RIGGER 0.10 0.06 -
HELPER 0.10 0.06 -

MATERIAL

PERALATAN
Tripod 0.06 70,000.00 4,200.00
Chain Blok 5 T 0.06 53,333.33 3,200.00
Hiab Crane 1,050,000.00 -

BAHAN (Habis Pakai)


Fuel Hiab Crane 10,945.00 -

7,400.00

I. 1 INSTALLATION VALVE
DIA 1" scd 40
MANHOUR PER EACH 0.20
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.02 -
PIPE FITTER 0.45 0.09 -
PIPE WELDER 0.20 0.04 -
H/E OPERATOR 0.05 0.01 -
RIGGER 0.10 0.02 -
HELPER 0.10 0.02 -

MATERIAL

PERALATAN
Tripod 0.02 70,000.00 1,400.00
Chain Blok 5 T 0.02 53,333.33 1,066.67
Hiab Crane 1,050,000.00 -

BAHAN (Habis Pakai)


Fuel Hiab Crane 10,945.00 -

2,466.67

I. 1 INSTALLATION VALVE
DIA 1/2 " 3/4"
MANHOUR PER EACH 0.10
Description compotiion MHRS Unit price total
TENAGA KERJA
FOREMAN 0.10 0.01 -
PIPE FITTER 0.45 0.05 -
PIPE WELDER 0.20 0.02 -
H/E OPERATOR 0.05 0.01 -
RIGGER 0.10 0.01 -
HELPER 0.10 0.01 -

MATERIAL

PERALATAN
Tripod 0.01 70,000.00 700.00
Chain Blok 5 T 0.01 53,333.33 533.33
Hiab Crane - 1,050,000.00 -

BAHAN (Habis Pakai)


Fuel Hiab Crane - 10,945.00 -

1,233.33

1 M2 PENGECATAN BESI (3X)

Page 46 of 52
Description compotiion MHRS Unit price total
MATERIAL
Meni Besi Kg 0.10 13,001.80 1,300.18
Kuas Bh 0.05 7,700.00 385.00
Cat dasar Kg 0.08 24,465.00 2,030.60
Cat Penutup Kg 0.20 137,500.00 27,500.00
Ampelas lbr 0.40 6,716.00 2,686.40
Minyak Cat ltr 0.15 23,467.00 3,520.05

TENAGA KERJA
HELPER org 0.20 - -
PAINTER org 0.06 - -
FOREMAN org 0.01 - -

PERALATAN
Compressor 0.06 1,430,000.00 85,800.00
123,222.23

Page 47 of 52
SUBJECT : BILL of QUANTITY & ANALISA HARGA SATUAN
PROJECT : PEMBANGUNANTERMINAL LPG PRESSURIZED DEPOT LPG PULAU LAYANG
SCOPE : PEKERJAAN ELEKTRIKAL

MATERIAL JASA

QUANTITY
Manhours include Koef. Equipment, Tools, &
Copy from unloading, inspection, Unit Rate
Consumables
No DESCRIPTION UNIT PRICE Remark Instrument Material Price in IDR transporting to point Labour
Price installation, installing,
aligning & checking.
Tools &
(IDR) (USD) Foreman Skilled Labour Helper Equipment
Consumables
Unit TOTAL
E F Bobot Komposisi 0.08 0.30 0.13 0.50 0.38 0.45 0.25

PLG-MTO-030-001-A4
1 Unit 1 TRANSFORMER
Immerssed Oil Transformer 20kV/400V, 400 kVA, 50 Hz. 11,950,000.00 11,950,000 896,250 268,875.00 33,609.38 134,437.50 100,828.13 403,312.50 224,062.50
Outdoor Installation including Power Panel and Accessories. - - - - - - - -
As per indicate on Data Sheet Transformer . - - - - - - - -
- - - - - - - -
2 MV SWITCHGEAR - - - - - - - -
a Unit 1 Incoming VCB 630 A 205,600,000.00 Industira 205,600,000 15,420,000 4,626,000.00 578,250.00 2,313,000.00 1,734,750.00 6,939,000.00 3,855,000.00
20 kV, 3-phase, 50 Hz, 25 kA/20kV, 3 wire, 3ph Metal Clad, IP 31, withdrawable - - - - - - - -
motorized include type protection relay device and accessories - - - - - - - -
b Unit 1 Outgoing VCB 630 A - - - - - - - -
20 kV, 3-phase, 50 Hz, 25 kA, 3 wire, 3ph Metal Clad, IP 31, withdrawable - - - - - - - -
motorized include type protection relay device and accessories - - - - - - - -
As per indicate on Data sheet no. PLG-DSH-030-003-A4 and Single Line Diagram - - - - - - - -
- - - - - - - -
3 LV SWITCHGEAR/ MCC - - - - - - - -
a Unit 1 Incoming ACB 500 A (from transformer) 446,370,000.00 Industira 446,370,000 33,477,750 10,043,325.00 1,255,415.63 5,021,662.50 3,766,246.88 15,064,987.50 8,369,437.50
a - Incoming ACB 500 A (from transformer) - - - - - - - -
400 V, 3-phase, 4 wires, 50 Hz, 25 kA, Metal Clad, IP 42, withdrawable - - - - - - - -
motorized, complete set relay protection and accessories - - - - - - - -
b - Incoming ACB 500 A (from DEG) - - - - - - - -
400 V, 3-phase, 4 wires, 50 Hz, 25 kA, Metal Clad, IP 42, withdrawable - - - - - - - -
motorized, Auto Transfer Switch (ATS) as outgoing as per single line diagram, complete set relay - - - - - - - -
protection and accessories - - - - - - - -
- Outgoing - - - - - - - -
c a. DOL starter (for Jockey Pump and Water Pit Pump), 400 V, - - - - - - - -
Include MCCB and accessories - - - - - - - -
d b. Feeder Include MCCB and accessories (To VSD, DP, etc.) - - - - - - - -
e c. Feeder Include MCCB and accessories (Spare) - - - - - - - -

4 - VSD PANEL
b. VSD (Variable Speed Drive) for LPG Truck filling pump, 400 V, 45 kW, Include MCCB and accessories - - - - - - - -

4 POWER DISTRIBUTION BOARD (PDB) - - - - - - - -


a Unit 1 PDB-01, 400 V, 3Ph, 4 Wire, 50Hz, 25 kW, 10 KA - - - - - - - -
Indoor used (IP 31), Wall Mounting, Plug in Type MCCB for incoming - - - - - - - -
c/w Surge Arrester,Voltmeter, Amperemeter & Indicating Lights (for each phase) for Incoming, - - - - - - - -
Incoming - - - - - - - -
- 1ea - MCCB 63A - - - - - - - -
Outgoing - - - - - - - -
- 20ea - MCB/ELCB 10A - - - - - - - -
- - - - - - - -
PDB-02, 400 V, 3Ph, 4 Wire, 50Hz, 10 kW, 10 KA - - - - - - - -
b Unit 1 Outdoor used (IP 55), Wall Mounting, Plug in Type MCCB for incoming, c/w Photocell circuit and HOA, - - - - - - - -
c/w Surge Arrester,Voltmeter, Amperemeter & Indicating Lights (for each phase) for Incoming, - - - - - - - -
Incoming - - - - - - - -
- 1ea - MCCB 20A - - - - - - - -
Outgoing - - - - - - - -
- 20ea - MCB/ELCB 10A - - - - - - - -
- - - - - - - -
c Unit 1 DBMOV-01, 400 V, 3Ph, 4 Wire, 50Hz, 15 kW, 16 KA - - - - - - - -
Outdoor used (IP 55), Wall Mounting, Plug in Type MCCB for incoming - - - - - - - -
c/w Surge Arrester,Voltmeter, Amperemeter & Indicating Lights (for each phase) for Incoming, - - - - - - - -
Incoming - - - - - - - -
- 1ea - MCCB 32A - - - - - - - -
Outgoing - - - - - - - -
- 15ea - MCB 10A - - - - - - - -
- - - - - - - -
5 UPS - - - - - - - -
a Unit 1 20 kVA Uniterruptible Power Supply, Industrial type, UPS system single with By Pass System package, Gutor - - - - - - - -
400V, 3-phase, 50hz input voltage, 1-phase 220V, 50 hz output with, - - - - - - - -
Type battery VRLA, 30 minute backup time 1 x 100%, including UPS Distribution Panel - - - - - - - -
UPS shall be indoor, IP 42 installed in air conditioned room, c/w accessories - - - - - - - -
SUBJECT : BILL of QUANTITY & ANALISA HARGA SATUAN
PROJECT : PEMBANGUNANTERMINAL LPG PRESSURIZED DEPOT LPG PULAU LAYANG
SCOPE : PEKERJAAN ELEKTRIKAL

MATERIAL JASA

QUANTITY
Manhours include Koef. Equipment, Tools, &
Copy from unloading, inspection, Unit Rate
Consumables
No DESCRIPTION UNIT PRICE Remark Instrument Material Price in IDR transporting to point Labour
Price installation, installing,
aligning & checking.
Tools &
(IDR) (USD) Foreman Skilled Labour Helper Equipment
Consumables
Unit TOTAL
E F Bobot Komposisi 0.08 0.30 0.13 0.50 0.38 0.45 0.25

- - - - - - - -
8 CAPACITOR BANK - - - - - - - -
a Unit 1 50 kVAR Capacitor Bank 99,770,000.00 Industira 99,770,000 7,482,750 2,244,825.00 280,603.13 1,122,412.50 841,809.38 3,367,237.50 1,870,687.50
Indoor Instalation IP 42. - - - - - - - -
- - - - - - - -
7 LOCAL CONTROL SWITCH - - - - - - - -
a Unit 1 Increased safety type, Push Button (Start/Stop), Hand - Off - Auto selectors switch with pad-lockable 850.00 850 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
at Stop position, Indication, 1 Hub M25, Ammeter. (for LPG Filling Truk Pump) - - - - - - - -
Weather proof, IP 55, Push Button (Start/Stop), Hand - Off - Auto selectors switch with pad-lockable - - - - - - - -
at Stop position, Indication, 1 Hub M25, Ammeter. (for Jockey Pump and Water Pit Pump) - - - - - - - -
- - - - - - - -
9 DIESEL ENGINE GENERATOR - - - - - - - -
a Unit 1 250 Kva Genset with 400V, 3 Phase, 50Hz, 0.8 PF output, 48,967.00 48,967 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Indoor Installation, IP 42, Complete with silencer, LCP - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
As per indicate on DEG Data Sheet no. PLG-DSH-030-002-A4. - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
10 OUTDOOR LIGHTING - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
a Unit 8 Floodlight High Pressure Sodium Pole Mounted, 400 watt, 220 VAC, 50 Hz, Stainless Steel 900.00 900 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Lumen Fixture min 55500, front Glass Retaining ring with, high Power Ballast, Lamp, impact, - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Eex ' e ' IP65 degree Reflector Broad-Beamed Outdoor, Resistant Temperature, front Glass - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
U-Shaped Mounting Bracket made of Pivots around Floodlight axis (infinitely adjustable). - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Completed with lighting pole, JB and accessories - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Incoming VCB 630 A - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
b Unit 13 Street Light High Pressure Sodium Pole Mounted (4 inch), 250 watt/HSE, 220 VAC, 50 Hz, 1,396.10 1,396 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Lumen Per Fixture min29000, with, high Power Ballast, (Without External Reflector) - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Outgoing VCB 630 A - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Completed with lighting pole 9 meters, JB and accessories - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
c Unit 5 Stanchion lighting, HPS 100 watt, 220 VAC, 50 Hz, pole mounted, 3 M Height 800.00 800 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
(Ex'e', Zone 2) - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Incoming ACB 500 A (from transformer) - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
11 INDOOR LIGHTING - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
a Unit 20 Fluorescent Lighting Fixtures, 2 x 36 W, 230 V, 50 Hz, Ceiling Mounted c/w 55.00 55 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Ballast and Frame. - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
b Unit 5 Fluorescent Lighting Fixtures, 2 x 36 W, 230 V, 50 Hz, Pendant Mounted c/w 350.00 350 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Ballast and Frame (Exe, Zone 2). - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
c Unit 1 Down Light, 1 x 18 W, 230 V, 50Hz, Ceiling Mounted. 40.00 40 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
d Unit 5 Receptacle, Flush Mounted, General Purpuse indoor type, 230 V, 1 P, 20A, 400VA. 7.50 8 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
e Unit 7 AC Receptacle, c/w on-off Switch, Flush Mounted, General Purpuse indoor type, 7.50 8 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
230 V, 1P, 20 A, 400VA. - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
e Unit 6 Switch one device 1 way, Flus Mounted. 7.50 8 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
f Unit 4 Switch one device 2 way, Flus Mounted. 7.50 8 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
11 AIR CONDITIONING & EX-HAUST - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
a Unit 4 Exhaust Fan,40 W- 220 VAC, 1-ph, 50 Hz (9.4 m³/mnt(CMM) ~ 331.96 ft³/mnt(CFM)), 10 " Blade- 37 37 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
Industrial Type - - - - - - - -
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
12 LIGHTING POLE - Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
a Unit 6 Flood light, Lighting pole octagonal Hot dipped galvanized 10000 mm height 546.10 546 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
b Unit 11 Street light, Lighting pole octagonal Hot dipped galvanized 7000 mm height 546.10 546 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
c Unit 4 2" Stanchion Lighting pole RGS conduit Hot dipped galvanized 3000 mm height 546.10 546 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- - - - - - - -
13 POWER CABLE - - - - - - - -
PT. Foxsel & PT.
a 437 411,765.00 411,765 30,882 9,264.71 1,158.09 4,632.36 3,474.27 13,897.07 7,720.59
Mtrs 3c - 35 mm2, Type N2XSERY, 20kV. Irham
b Mtrs 288 4c - 185 mm2, Type N2XRY, 0.4kV. 1,529,706.00 1,529,706 114,728 34,418.38 4,302.30 17,209.19 12,906.89 51,627.58 28,681.99
c Mtrs 81 4c - 150 mm2, Type N2XRY, 0.4kV. 963,176.00 963,176 72,238 21,671.46 2,708.93 10,835.73 8,126.80 32,507.19 18,059.55
d Mtrs 288 4c - 35 mm2, Type N2XRY, 0.4kV. 256,471.00 256,471 19,235 5,770.60 721.32 2,885.30 2,163.97 8,655.90 4,808.83
e Mtrs 288 4c - 25 mm2, Type N2XRY, 0.4kV. 201,294.00 201,294 15,097 4,529.12 566.14 2,264.56 1,698.42 6,793.67 3,774.26
f Mtrs 322 4c - 16 mm2, Type N2XRY, 20kV. 148,588.00 148,588 11,144 3,343.23 417.90 1,671.62 1,253.71 5,014.85 2,786.03
g Mtrs 368 3c - 35 mm2, Type N2XRY, 0.4kV. 192,363.00 192,363 14,427 4,328.17 541.02 2,164.08 1,623.06 6,492.25 3,606.81
SUBJECT : BILL of QUANTITY & ANALISA HARGA SATUAN
PROJECT : PEMBANGUNANTERMINAL LPG PRESSURIZED DEPOT LPG PULAU LAYANG
SCOPE : PEKERJAAN ELEKTRIKAL

MATERIAL JASA

QUANTITY
Manhours include Koef. Equipment, Tools, &
Copy from unloading, inspection, Unit Rate
Consumables
No DESCRIPTION UNIT PRICE Remark Instrument Material Price in IDR transporting to point Labour
Price installation, installing,
aligning & checking.
Tools &
(IDR) (USD) Foreman Skilled Labour Helper Equipment
Consumables
Unit TOTAL
E F Bobot Komposisi 0.08 0.30 0.13 0.50 0.38 0.45 0.25

h Mtrs 368 3c - 16 mm2, Type N2XRY, 0.4kV. 111,618.00 111,618 8,371 2,511.41 313.93 1,255.70 941.78 3,767.11 2,092.84
i Mtrs 368 3c - 10 mm2, Type N2XRY, 0.4kV. 75,441.00 75,441 5,658 1,697.42 212.18 848.71 636.53 2,546.13 1,414.52
j Mtrs 1783 2c - 2.5 mm2, Type N2XRY, 0.4kV. 35,647.00 35,647 2,674 802.06 100.26 401.03 300.77 1,203.09 668.38
k Mtrs 518 2c - 10 mm2, Type N2XRY, 0.4kV. 50,294.00 50,294 3,772 1,131.61 141.45 565.81 424.36 1,697.42 943.01
l Mtrs 184 2c - 16 mm , Type
2
N2XRY, 0.4kV. 76,471.00 76,471 5,735 1,720.60 215.07 860.30 645.22 2,580.90 1,433.83
m Mtrs 46 2c - 50 mm2, Type N2XRY, 0.4kV. 205,882.00 205,882 15,441 4,632.34 579.04 2,316.17 1,737.13 6,948.52 3,860.29
- - - - - - - -
14 CONTROL CABLE - - - - - - - -
a Mtrs 506 10c - 1.5 mm2, Type N2XRY, 0.4kV. 101,471.00 101,471 7,610 2,283.10 285.39 1,141.55 856.16 3,424.65 1,902.58
- - - - - - - -
15 LIGHTING CABLE - - - - - - - -
INDOOR - - - - - - - -
a Mtrs 345 3c - 2.5 mm2, Type N2XRY, 0.4kV. 38,235.00 38,235 2,868 860.29 107.54 430.14 322.61 1,290.43 716.91
- - - - - - - -
OUTDOOR - - - - - - - -
a Mtrs 483 3c - 2.5 mm2, Type N2XRY, 0.4kV. 38,235.00 38,235 2,868 860.29 107.54 430.14 322.61 1,290.43 716.91
b Mtrs 460 3c - 4 mm2, Type N2XRY, 0.4kV. 48,353.00 48,353 3,626 1,087.94 135.99 543.97 407.98 1,631.91 906.62
c Mtrs 805 3c - 6 mm2, Type N2XRY, 0.4kV. 59,294.00 59,294 4,447 1,334.12 166.76 667.06 500.29 2,001.17 1,111.76
16 CABLE GLAND - - - - - - - -
Cable Gland Industrial Type made of Nickle & Plate brass. - - - - - - - -
Completed with heat shrink tube. - - - - - - - -
a EA 81 M20 30.00 30 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
b EA 58 M25 35.00 35 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
c EA 35 M32 55.00 55 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
d EA 7 M50 85.00 85 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
e EA 7 M63 93.50 94 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
17 CABLE LUG 0.50 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
a EA 100 1,5 mm² 0.50 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
b EA 55 2,5 mm² 0.50 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
c EA 11 4 mm² 0.50 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
d EA 11 6 mm² 0.80 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
e EA 37 10 mm² 0.80 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
f EA 22 16 mm² 0.10 0 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
g EA 22 25 mm² 0.20 0 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
h EA 22 35 mm² (Termination Kit 20 kV) 150.35 150 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
i EA 55 70 mm² 0.80 1 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
j EA 55 95 mm² 10.00 10 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
k EA 11 150 mm² 12.00 12 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
l EA 11 185 mm² 13.20 13 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509 Err:509
- - - - - - - -
18 GROUNDING CABLE - - - - - - - -
Type:NYY - - - - - - - -
a Mtrs 529 Size:1C-95 mm² 89,399.00 89,399 6,705 2,011.48 251.43 1,005.74 754.30 3,017.22 1,676.23
Type:NYY - - - - - - - -
b Mtrs 575 Size:1C-70 mm² 47,557.00 47,557 3,567 1,070.03 133.75 535.02 401.26 1,605.05 891.69
Type:NYY - - - - - - - -
c Mtrs 345 Size:1C-25 mm² 39,117.00 39,117 2,934 880.13 110.02 440.07 330.05 1,320.20 733.44
- - - - - - - -
19 GROUND ROD - - - - - - - -
a EA 22 3/4" Dia, 3000 mm Lg, Ground Rod Copper Clad Steel. 770,000 770,000 57,750 17,325.00 2,165.63 8,662.50 6,496.88 25,987.50 14,437.50
- - - - - - - -
20 GROUND PIT - - - - - - - -
a EA 1 3/4" Dia, 3000 mm Lg, Ground Rod Copper Clad Steel. 770,000.00 770,000 57,750 17,325.00 2,165.63 8,662.50 6,496.88 25,987.50 14,437.50
- - - - - - - -
21 LIGHTNING PROTECTION - - - - - - - -
a EA 1 Lightning Protection " E-F" Carrier System. 45,000,000 45,000,000 3,375,000 1,012,500.00 126,562.50 506,250.00 379,687.50 1,518,750.00 843,750.00
b EA 23 Lightning Protection " Coventiona l" System. - - - - - - - -
- - - - - - - -
22 LIGHTNING POLE - - - - - - - -
a EA 1 Lightning Protection Pole Octagonal Hot Dip Galvanizized 22000 mm Height. 18,000,000 18,000,000 1,350,000 405,000.00 50,625.00 202,500.00 151,875.00 607,500.00 337,500.00
b EA 23 Lightning Protection " Coventiona l" System. - - - - - - - -
- - - - - - - -
SUBJECT : BILL of QUANTITY & ANALISA HARGA SATUAN
PROJECT : PEMBANGUNANTERMINAL LPG PRESSURIZED DEPOT LPG PULAU LAYANG
SCOPE : PEKERJAAN ELEKTRIKAL

MATERIAL JASA

QUANTITY
Manhours include Koef. Equipment, Tools, &
Copy from unloading, inspection, Unit Rate
Consumables
No DESCRIPTION UNIT PRICE Remark Instrument Material Price in IDR transporting to point Labour
Price installation, installing,
aligning & checking.
Tools &
(IDR) (USD) Foreman Skilled Labour Helper Equipment
Consumables
Unit TOTAL
E F Bobot Komposisi 0.08 0.30 0.13 0.50 0.38 0.45 0.25

23 CABLE TRAY - - - - - - - -
a EA 35 200W x 100D Perforated Tray Galvanized. 849,600.00 849,600 63,720 19,116.00 2,389.50 9,558.00 7,168.50 28,674.00 15,930.00
b EA 18 150W x 100D Perforated Tray Galvanized. 723,300.00 723,300 54,248 16,274.25 2,034.28 8,137.13 6,102.84 24,411.38 13,561.88
c EA 18 100W x 100D Perforated Tray Galvanized. 597,100.00 597,100 44,783 13,434.75 1,679.34 6,717.38 5,038.03 20,152.13 11,195.63
- - - - - - - -
24 HORIZONTAL TEE - - - - - - - -
a EA 3 200W x 200H x 100D Perforated Tray Galvanized. 530,300.00 530,300 39,773 11,931.75 1,491.47 5,965.88 4,474.41 17,897.63 9,943.13
b EA 2 150W x 150H x 100D Perforated Tray Galvanized. 462,900.00 462,900 34,718 10,415.25 1,301.91 5,207.63 3,905.72 15,622.88 8,679.38
- - - - - - - -
25 UNEQUAL TEE - - - - - - - -
a EA 3 200W x 150H x 100D Perforated Tray Galvanized. 530,300.00 530,300 39,773 11,931.75 1,491.47 5,965.88 4,474.41 17,897.63 9,943.13
b EA 6 150W x 1000H x 100D Perforated Tray Galvanized. 462,900.00 462,900 34,718 10,415.25 1,301.91 5,207.63 3,905.72 15,622.88 8,679.38
26 HORIZONTAL ELBOW - - - - - - - -
a EA 3 200W x 200H x 100D Perforated galvanized cable tray 404,000.00 404,000 30,300 9,090.00 1,136.25 4,545.00 3,408.75 13,635.00 7,575.00
b EA 6 150W x 150H x 100D Perforated galvanized cable tray 342,800.00 342,800 25,710 7,713.00 964.13 3,856.50 2,892.38 11,569.50 6,427.50
c EA 6 100W x 100H x 100D Perforated galvanized cable tray 295,800.00 295,800 22,185 6,655.50 831.94 3,327.75 2,495.81 9,983.25 5,546.25
- - - - - - - -
27 OUTSIDE RISER - - - - - - - -
a EA 3 200W Outside Vertical Radius 450 Perforated galvanized cable tray 366,000.00 366,000 27,450 8,235.00 1,029.38 4,117.50 3,088.13 12,352.50 6,862.50
b EA 6 150W x 150H x 100D Perforated galvanized cable tray 313,800.00 313,800 23,535 7,060.50 882.56 3,530.25 2,647.69 10,590.75 5,883.75
- - - - - - - -
28 INTSIDE RISER - - - - - - - -
a EA 3 200W Outside Vertical Radius 450 Perforated galvanized cable tray 366,000.00 366,000 27,450 8,235.00 1,029.38 4,117.50 3,088.13 12,352.50 6,862.50
b EA 6 150W x 150H x 100D Perforated galvanized cable tray 313,800.00 313,800 23,535 7,060.50 882.56 3,530.25 2,647.69 10,590.75 5,883.75
- - - - - - - -
29 STREED REDUCER - - - - - - - -
a EA 6 200W x 150W Perforated galvanized cable tray 332,800.00 332,800 24,960 7,488.00 936.00 3,744.00 2,808.00 11,232.00 6,240.00
b EA 9 150W x 100W Perforated galvanized cable tray 290,900.00 290,900 21,818 6,545.25 818.16 3,272.63 2,454.47 9,817.88 5,454.38
- - - - - - - -
30 JOINT SET - - - - - - - -
a EA 345 Joint set, Complete With 6ea Bolt, Nuts & Washers 316 SS. 22,000.00 22,000 1,650 495.00 61.88 247.50 185.63 742.50 412.50
- - - - - - - -
31 SIGNS POST - - - - - - - -
250 x 250 Concrete Yellow Coloed - - - - - - - -
a EA 6 Sign "B" - - - - - - - -
b EA 20 Sign " C" 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
c EA 6 Sign " D" 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
32 SUPPORT - - - - - - - -
a EA 11 50 mm x 50 mm x 6thk, 6000 mm Lg, Steel Angle. 250,000.00 250,000 18,750 5,625.00 703.13 2,812.50 2,109.38 8,437.50 4,687.50
b EA 11 40 mm x 30 mm x 10 mm x 2.5 thk 6000 mm Lg, Unistrut Galvanized. 250,000.00 250,000 18,750 5,625.00 703.13 2,812.50 2,109.38 8,437.50 4,687.50
c EA 17 100 mm x 50 mm x 6thk, 6000 mm Lg, Steel Channel. 250,000.00 250,000 18,750 5,625.00 703.13 2,812.50 2,109.38 8,437.50 4,687.50
d EA 17 3/4" conduit Galvanized Steel 6000 mm Lg. 250,000.00 250,000 18,750 5,625.00 703.13 2,812.50 2,109.38 8,437.50 4,687.50
- - - - - - - -
33 FLEXIBLE CONDUIT - - - - - - - -
a EA 11 3/4" Flexible Conduit, Liquit Tight Galvanized strong steel strip helically wound 300,000.00 300,000 22,500 6,750.00 843.75 3,375.00 2,531.25 10,125.00 5,625.00
with nylon sealing cord heavy duty flexible PVC covered, water tight seal, UL A2066 - - - - - - - -
bonded liquit tight in size 3/4" IEC 529. - - - - - - - -
- - - - - - - -
34 CONDUIT FITTING - - - - - - - -
a EA 12 3/4" Conduit Union Hot Dio Gakvanized 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
b EA 12 3/4" Conduit Coupling Hot Dip Galvanized 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
c EA 12 3/4" Conduit body 90o elbow Hot Dip Calvanized 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
d EA 12 3/4" Conduit body "TE" Hot DIP galvanized c/w terminal 4 mm2 4ea. 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
e EA 12 3/4" Conduit body " CROSS " Hot DIP Galvanized c/w terminal 4 mm2 4ea. 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
f EA 12 3/4" Conduit body Type " LR" Hot Dip Galvanized. 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
g EA 12 3/4" Conduit body Type "LL" Hot Dip Galvanized. 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
- - - - - - - -
35 CONDUIT OUTLET GASKETED & RINGS - - - - - - - -
EA 23 Squar wall box with lock nuts. 400,000.00 400,000 30,000 9,000.00 1,125.00 4,500.00 3,375.00 13,500.00 7,500.00
EA 58 3/4" diameter conduit bushing hot dip Galvanized. 100,000.00 100,000 7,500 2,250.00 281.25 1,125.00 843.75 3,375.00 1,875.00
- - - - - - - -
SUBJECT : BILL of QUANTITY & ANALISA HARGA SATUAN
PROJECT : PEMBANGUNANTERMINAL LPG PRESSURIZED DEPOT LPG PULAU LAYANG
SCOPE : PEKERJAAN ELEKTRIKAL

MATERIAL JASA

QUANTITY
Manhours include Koef. Equipment, Tools, &
Copy from unloading, inspection, Unit Rate
Consumables
No DESCRIPTION UNIT PRICE Remark Instrument Material Price in IDR transporting to point Labour
Price installation, installing,
aligning & checking.
Tools &
(IDR) (USD) Foreman Skilled Labour Helper Equipment
Consumables
Unit TOTAL
E F Bobot Komposisi 0.08 0.30 0.13 0.50 0.38 0.45 0.25

36 CABLE MARKER - - - - - - - -
a Roll 15 Metal Embossing Tape System 316 Grade Stanless Steel. 50,000.00 50,000 3,750 1,125.00 140.63 562.50 421.88 1,687.50 937.50
b Set 1 Tol Kit Include tool, carrying case, Cable core marker c/w Characters. 2,500,000.00 2,500,000 187,500 56,250.00 7,031.25 28,125.00 21,093.75 84,375.00 46,875.00
0 - number - - - - - - - -
1 - number - - - - - - - -
2 - number - - - - - - - -
3 - number - - - - - - - -
4 - number - - - - - - - -
5 - number - - - - - - - -
6 - number - - - - - - - -
7 - number - - - - - - - -
8 - number - - - - - - - -
9 - number - - - - - - - -
A - number - - - - - - - -
B - number - - - - - - - -
C - number - - - - - - - -
D - number - - - - - - - -
E - number - - - - - - - -
F - number - - - - - - - -
G- number - - - - - - - -
H- number - - - - - - - -
I - number - - - - - - - -
J - number - - - - - - - -
K - number - - - - - - - -
L - number - - - - - - - -
M - number - - - - - - - -
N - number - - - - - - - -
O - number - - - - - - - -
P - number - - - - - - - -
Q - number - - - - - - - -
R - number - - - - - - - -
S - number - - - - - - - -
T - number - - - - - - - -
U - number - - - - - - - -
V - number - - - - - - - -
W - number - - - - - - - -
X - number - - - - - - - -
Y - number - - - - - - - -
Z - number - - - - - - - -
- - - - - - - -
37 ELECTRICAL CABLE TAPE - - - - - - - -
a Roll 17 Electrical Vinyl Insulation Tape Red Colour. 65,000 65,000 4,875 1,462.50 182.81 731.25 548.44 2,193.75 1,218.75
b Roll 17 Electrical Vinyl Insulation Tape Black Colour. 65,000 65,000 4,875 1,462.50 182.81 731.25 548.44 2,193.75 1,218.75
c Roll 17 Electrical Vinyl Insulation Tape Blue Colour. 65,000 65,000 4,875 1,462.50 182.81 731.25 548.44 2,193.75 1,218.75
d Roll 17 Electrical Vinyl Insulation Tape Yellow Colour. 65,000 65,000 4,875 1,462.50 182.81 731.25 548.44 2,193.75 1,218.75
e Roll 17 Electrical Vinyl Insulation Tape Green Colour. 65,000 65,000 4,875 1,462.50 182.81 731.25 548.44 2,193.75 1,218.75
- - - - - - - -
38 CABLE TIES - - - - - - - -
Fully Coated Stainless Steel 316 SS Cable Ties. - - - - - - - -
a EA 230 4.6 mm (w) x 201 mm (L) 700,000 700,000 52,500 15,750.00 1,968.75 7,875.00 5,906.25 23,625.00 13,125.00
b EA 230 4.6 mm (w) x 362 mm (L) 700,000 700,000 52,500 15,750.00 1,968.75 7,875.00 5,906.25 23,625.00 13,125.00
c EA 115 4.6 mm (w) x 521 mm (L) 700,000 700,000 52,500 15,750.00 1,968.75 7,875.00 5,906.25 23,625.00 13,125.00
d Pack 17 Sealng Compound. 70,000.00 70,000 5,250 1,575.00 196.88 787.50 590.63 2,362.50 1,312.50
- - - - - - - -
39 WARE JOINT - - - - - - - -
a Set 80 Size:2C-2.5 mm² STA-KON Ware Jints One Piece Nylon self-insulation. 5,000.00 5,000 375 112.50 14.06 56.25 42.19 168.75 93.75
b Set 50 Size:2C-4 mm² STA-KON Ware Jints One Piece Nylon self-insulation. 5,000.00 5,000 375 112.50 14.06 56.25 42.19 168.75 93.75
- - - - - - - -
- - - - - - - -
- - - - - - - -
- - - - - - - -

Anda mungkin juga menyukai