CARA PENANGGULANGAN NYA PADA PEMBUATAN GIGI TIRUAN KERANGKA LOGAM (Co-Cr ) ABSTRAK
Latar belakang : Dalam pembuatan gigi tiruan kerangka logam terdapat
beberapa tahapan diantaranya persiapan model, survey, block out, desain, duplikasi model kerja, waxing, pemasangan sprue ,penanaman, buang malam, pre heating, penuangan logam, sandblasting, fitting, elektropolishing hingga tahapan terakhir finishing and polishing. Pada tahapan penuangan logam sangat perlu di perhatikan karena sering kali terjadi kegagalan. Tujuan : Ingin mengetahui tentang penyebab kegagalan hasil penuangan logam dan cara menanggulanginya pada pembuatan gigi tiruan kerangka logam. Tinjauan pustaka : Gigi tiruan kerangka logam adalah salah satu jenis gigi tiruan lepasan yang terbuat dari logam campur, sedangkan anasir giginya terbuat dari resin akrilik atau porselen, karena bahan logam campur cukup kuat dan dapat dibuat lebih tipis sehingga pemakai akan merasa lebih nyaman. Dalam pembuatan gigi tiruan kerangka logam terdapat tahapan yang harus diperhatikan karena sering terjadi kegagalannya yaitu pada tahapan penuangan logam, kegagalan-kegagalan penuangan logam tersebut diantaranya : distorsi, permukaan hasil penuangan kasar, hasil penuangan tidak lengkap, bersayap, tepi yang membulat dan porus. Kesimpulan : Kegagalan- kegagalan pada proses penuangan logam biasa disebabkan karena bermacam-macam hal antara lain dalam perlekatan sprue yang salah, prosedur penanaman yang kurang baik, pemanasan mould yang tidak sesuai, serta pelaksanaan penuangan logam yang tidak benar. Untuk itu harus memperhatikan prosedur-prosedur pembuatan gigi tiruan kerangka logam dengan benar, sehingga kegagalan penuangan logam tidak perlu terjadi.
Kata kunci : kegagalan penuangan logam, gigi tiruan kerangka logam.
TUGAS AKHIR KEGAGALAN HASIL PENUANGAN... ULFA NUR KHOLILAH
IR- PERPUSTAKAAN UNIVERSITAS AIRLANGGA
FAILURE OF METAL CASTING AND HOW TO
OVERCOME THEM ON MAKING METAL FRAME DENTURE (Co-Cr)
ABSTRACT
Background : In fabrication of denture metal framework there are several
stages including model preparation, survey, block out, design, duplication of work model, waxing, attachment sprue, planting, waste night, pre heating, metal casting, sandblasting, fitting, electropolishing until last stage finishing and polishing. At the stage of metal casting is necessary to note because of frequent failures. Purpose : Want to know about the cause of the failure of metal casting and how to overcome it on the manufacture of denture metal framework. Literature review : Denture metal framework tooth is one type of artificial tooth made of alloy, while dental anasir is made of acrylic or porcelain resin, because the metal material is strong enough and can be made thinner so that the weare will feel more comfortable. In the manufacture of denture metal framework there are stages that must be noticed because there is often a failure that is at the metal casting stage, the metal casting failures are among others : distortion, rough surface, incomplete metal casting, winged rounded edges, porous. Conclusions : Common metal casting failures are caused by a variety of things including in the wrong sprue attachment, poor planting procedures, improperly molded heating, and improper metal casting. For that reason should pay attention to the procedures of making metal denture fabric properly, so that the metal casting failure does not need to happen.
Keywords : Metal casting, denture metal framework.
vi
TUGAS AKHIR KEGAGALAN HASIL PENUANGAN... ULFA NUR KHOLILAH