JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY 1. Persiapan pekerja,alat dan material. 1.1. Pekerja tidak fit dan 1.1.1. Orang yang terlibat dalam pekerjaan harus Preparation tools and materials tidak kompeten memastikan mereka sudah fit untuk melakukan kerja Workers unfit and not dan melakukan prejob meeting competance Ensure workers have fit and to do prejob meeting 1.1.2. Pastikan pekerja kompeten dan sudah paham terkait pekerjaan yang akan dilakukan Pekerja Pengawas Ensure workers competence and unserstand about his Workers Supervisor job 1.1.3. Pastikan operator/ pekerja adalah orang yang berpengalaman dan memiliki SIO yang masih berlaku. Make sure the operator / Workers are people who are experienced and have a valid SIO. 1.2. Kurang Informasi dan 1.2.1. Toolbox meeting/briefing dilakukan sebelum komunikasi. melakukan pekerjaan dipimpin oleh pengawas atau Less of information and safety communication Do toolbox meeting before job and lead by supervisor 1.2.2. Pastikan instruksi kerja telah di pahami semua team Pekerja Pengawas kerja yang terlibat dalam pekerjaan. Workers Supervisor Make sure work instruction have understood by workers 1.2.3. Selalu bertanya kepada pengawas bila kurang paham dengan pekerjaan yg di lakuakan. Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1 CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY Always confirm to supervisor if any less information 1.3. Alat kerja tidak 1.3.1. Perkakas atau semua alat kerja dalam kondisi sesuai/rusak. bersih/baik, layak pakai dan sudah dilakukan Pekerja Pengawas Tools demage pengecekan. Gunakan alat sesuai fungsinya. Workers Supervisor Tools have checked and must in good condition. Only using suitable tools as the function 1.4. Bakerja di ketinggian 1.4.1. Pastikan permit bekerja di ketinggian telah dibuat dan Work at height mendapat persetujuan Pekerja Pengawas Ensure WAH permit have been prepared well and got Workers Supervisor approved 2. Traveling Crane ke lokasi kerja 2.1 Jalan menuju tempat 2.1.1 Survey lokasi jalan yang kan dilalui, pastikan tidak Traveling Crane to workplace kerja rusak, amblas, miring dan licin. Jangan lanjutkan perjalanan jika licin dan terkadang akses crane tidak aman berkabut di pagi dan Survey the location of roads impassable, making sure sore hari not tilted and slippery. Do not continue your journey if Poor access access is not safe crane Pengawas Operator crane 2.1.2 Tersedia Spotter untuk mengarahkan operator Supervisor Spotter Available for direct operator 2.1.3 Operator memastikan unit di tempatkan sesuai instruksi Operator ensure the unit in place appropriate instructions 2.2 Interaksi dengan unit 2.2.1 Perhatikan jalan saat mengendarai unit lain Pay attention to the road while driving unit Interaction with other 2.2.2 Mengikuti aba-aba yang diberikan oleh spotter units Following the command that given by spotter Pengawas 2.2.3 Patuhi rambu-rambu lalu lintas yang berlaku. Operator crane Supervisor Following safety traffic sign 2.2.4 Pastikan daerah yng dilalui aman untuk dilewati (listrik, fasilitas air dsb). Ensure safe access for crane manouver 3. Menempatkan crane untuk material 3.1 Kondisi tanah lembek/ 3.1.1 Keluarkan full outrigger crane dan pastikan posisi yang akan diangkat tidak stabil (amblas), tempat landasan out rigger diberikan bantalan kayu Setting crane miring atau landing plate Pengawas Unlevel ground and soft Setting outrigger safe and ensure outrigger pad placed Operator crane Supervisor soil 3.1.2 Amati kondisi tanah, apakah ada potensi amblas atau tidak Observe the condition of the land, whether or not there
Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1
CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY is a potential broken 3.1.3 Pastikan type permukaan tanah keras dan datar dalam posisi aman Make sure the type of soil hard and flat surface in a safe position 3.2 Interaksi dengan 3.2.1 Berikan barikade atau safety cone di sekitar crane pekerja dan unit lain Provide safety barricades or cones around cranes Pengawas Interaction with Operator crane Supervisor Workers and other units 4. Memasang dan melepas lifting gears 4.1 Posisi lifting gear salah 4.1.1 Gunakan lifting gear dan pasang di tengah sudut pada hook dan material penempatan, sebagai penyeimbang pengangaktan Installing and removing lifting gear to Wrong setting lifting Use lifting gear and plug in the middle of the corner as Pengawas Rigger hook gears a counterweight removal Supervisor 4.1.2 Buka sebagian atap untuk memasang lifting gear Open part of the roof to install lifting gear 4.2 Lifting gear tidak 4.2.1 Pastikan lifting gear tidak cacat dan masih layak pakai layak pakai atau tidak Make sure lifting gear is not disabled and are still sesuai dg material yg worth taking Pengawas diangkat 4.2.2 Gunakan shackle sesuai dengan kapasitas material yg Rigger Supervisor Lifting gears not akan diangkat suitable or demage Use shackle accordance with the capacity of the material that will be removed 4.3 Lifting gears jatuh 4.3.1 Pastikan safety latch terpasang pada hook dan dalam (menimpa). kondis baik Lifting gears fall Make sure the safety latch on the hook attached and in good condition 4.3.2 Tidak dibenarkan berdiri di bawah hook It is not justified standing under hook Pengawas 4.3.3 Hook diturunkan untuk memudahkan pemasangan Rigger Supervisor lifting gears Hook lowered for easier installation of lifting gears 4.3.4 Jangan memasang shackle dalam posisi terbalik (pin dijadikan sebagai titik angkat) Do not install shackle in an inverted position (pin serve as the point of lift) 4.4 Titik jepit 4.4.1 Material yang akan diikat diganjal sedemikian rupa Pengawas Rigger Pinch point untuk menghindari tangan terjepit saat memasang Supervisor
Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1
CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY lifting gears The material to be tied fouled such a way as to avoid hand pinched when installing lifting gears 4.4.2 Perhatikan tangan saat memasang lifting gears Beware your hand 4.4.3 Komunikasi yang baik antara pekerja Keep good communication to other workers 5. Mengangkat material 5.1 Kapasitas crane tidak 5.1.1 Gunakan crane dengan kapasitas SWL lebih besar Lifting materials memadai (counter dari material yg akan diangkat weight atau boom) Use SWL crane with a capacity greater than the Pengawas Rigger insufficient capacity material that will be lifted Supervisor crane 5.1.2 Membuat lifting study untuk pengangakatan atap Arrange lifting plan 5.2 Sling rusak akibat sisi 5.2.1 Berikan pelindung/proteksi berupa ban bekas atau yng material yg tajam lainnya pada sudut-sudut yang tajam Pengawas Rigger Sling damaged by the Give protector / protection in the form of old tires or Supervisor sharp material other on sharp corners 5.3 Beban terayun tidak 5.3.1 Gunakan tagline untuk mengarahkan beban terkontrol dan Use tagline menabrak 5.3.2 Rigger harus memperhatikan posisi berdirinya Pengawas Rigger Expenses Rigger should pay attention to his stance Supervisor uncontrolled swinging 5.3.3 Operator harus mengikuti aba-aba dari signalman Operator must following instruction that given by rigger 5.4 Titik jepit 5.4.1 Perhatikan tangan saat bekerja Pinch point Pay attention for your hand Pengawas Rigger 5.4.2 Jangan terburu-buru dalam bekerja Supervisor Dont rush during work 5.5 Kelebihan beban 5.5.1 Beban ynag diangkat masih dalam beban angkat Overload crane yang terdapat pada load chart Use SWL crane with a capacity greater than the material will be lifted 5.5.2 Pada saat swing perhatikan radius dan boom angle. Pengawas At the time of notice swing radius and boom angle Operator, rigger Supervisor 5.5.3 Operator harus memperhatikan load indikator yang terpasang di dalam kabin Operators should pay attention to load indicator installed inside the cabin 5.5.4 Rubah posisi crane jika beban tidak dimungkinkan
Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1
CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY untuk diangkat dengan radius yang jauh Change the position of the crane if the load is not possible to be appointed with a radius much 5.6 Terjadi hujan (angin 5.6.1 Semua kru diminta turun jika ada indikasi akan terjadi kencang) dan Petir angin kencang rain (strong wind) and All the crew asked to come down if there are Lightning indications there will be strong winds Pengawas Operator 5.6.2 Turunkan segera boom telescopic crane. Jika hujan Supervisor berkepanjangan, maka boom latice harus direbahkan Lower the telescopic boom crane immediately. If prolonged rain, then boom Latice must recline 5.7 Interaksi dengan 5.7.1 Berikan barikade atau safety cone di sekitar crane pekerja dan unit lain Provide safety barricades or cones around cranes Operator and Pengawas Interaction with rigger Supervisor Workers and other units 6. Setting rangka batching plant di atas 6.1 Titik jepit 6.1.1 Pastikan semua orang yang terlibat dalam ketinggian dan penggunaan non Pinch point pengangkatan menggunakan Alat Pelindung Diri yang power tools sesuai. Setting structure at height and using Use suitable PPE correctly non power tools 6.1.2 Karyawan yang terlibat memperhatikan tangan saat bekerja Pekerja Pengawas Always eyes on your hand Workers Supervisor 6.1.3 Kenali karakteristik benda yang akan dikerjakan Known characteristic of materials 6.1.4 Melihat posisi tangan rekan kerja pada saat proses penurunan materials oleh crane Looking at the position of the hands of co-workers during the process of decline of the materials by crane 6.2 Material tajam 6.2.1 Perhatikan objek benda yang akan dikerjakan. Sharpness edge of Known characteristic of materials materials 6.2.2 Pastikan tangan dan anggota tubuh terhindar dari titik Pekerja Pengawas gores. Workers Supervisor Ensure your hand and others free from sharpness materials 6.3 Bekerja di ketinggian 6.3.1 Gunakan fullbody harness dan di cantolkan dengan Pekerja Pengawas Work at height benar pada life line atau anchor point yang kuat. Workers Supervisor Use fullbody harness and Anchored correctly on the
Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1
CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY life line or anchor point is strong. 6.3.2 Gunakan chin strap pada helmet Using chin strap for helmet 6.3.3 Pekerjaan tidak dilakukan sendirian (minimal dilakukan lebih dari 1 orang) Workers do not do alone (at least do more than one person) 6.3.4 Gunakan tangga untuk akses naik turun dengan menggunakan 3 kontak poin. Use ladder by three contact points. 6.3.5 Jangan membawa material atau alat ketika bekerja di atas ketinggian dan menaiki dan menuruni tangga Do not carry materials or tools when working on the altitude and up and down stairs 6.3.6 Gunakan tali untuk menaikkan dan menurunkan material Use a rope to raise and lower material 6.3.7 dilarang melempar atau membuang barang dari atas prohibited throw or throw items from the top 6.4 Alat dan material jatuh 6.4.1 Amankan lokasi dengan memasang barikade dari ketinggian Set barricade tape around workpalce Falling object 6.4.2 Tools dan material disimpan dalam tool bag atau diikat. Tools and materials keep in bag or tied for lifting manually Pekerja Pengawas 6.4.3 Jangan membawa material dengan tangan saat Workers Supervisor naik/turun tangga, Dont handle anything if you are going up and down ladder 6.4.4 Gunakan 3 titik tumpu saat menaiki dan menuruni tangga Use three point contact for going up and down ladder 7. Pekerjaan selesai 7.1. Sampah 7.1.1. Pastikan sampah dikumpulkan dan dibuang pada Housekeeping Trash / garbage tempat yang telah ditentukan. Ensure trash collected and put in bins Pekerja Pengawas 7.1.2. Semua sampah atau sisa-sisa potongan seng sudah Workers Supervisor di buang atau di tempatkan di tempat sampah. Put trash to the appropriate bin
Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1
CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY 7.1.3. Amankan area tumpukan sampah dgn memasang baricade. Keep safe trash with install barricade 7.2. Material dan peralatan 7.2.1. Bersihkan lokasi kerja dan bersihkan perkakas kerja. berserakan Cleaning tools and workpalce from trash/ garbage Bad housekeeping 7.2.2. Rapikan dan susun kembali perkakas kerja pada tempatnya. Pekerja Pengawas Storing tools to warehouse or tool box Workers Supervisor 7.2.3. Pastikan peralatan listrik yang dipakai sudah dalam posisi OFF (mati) Ensure power tools in off position
Oct 2016 BUMA-SWFP-HSE-JSEA-001-A1
CONTROLS REQUIRED WHO JOB STEP HAZARDS IDENTIFIED (Remember the hierarchy of control) ACTION BY VERIFIED BY