Tutorial Surpac6 - 05 - Pit & Dump Design
Tutorial Surpac6 - 05 - Pit & Dump Design
MINETECH INDONESIA
MEI 2020
Tutorial Surpac 6 – Pit & Dump Design 2020
DAFTAR ISI
1. PENGANTAR ....................................................................................................................................... 1
2. PERSIAPAN.......................................................................................................................................... 1
3. PEMBUATAN KONTUR STRIPPING RATIO.......................................................................................... 2
3.1. Membedakan Ore dan Waste ....................................................................................................... 2
3.2. Menghitung Ketebalan Ore dan Waste ........................................................................................ 7
3.3. Membuat Contour Stripping Ratio ............................................................................................. 26
4. MEMBUAT PIT DESIGN .................................................................................................................... 38
4.1. Membatasi Area Blok Model ...................................................................................................... 40
4.2. Membuat Ultimate Pit ................................................................................................................. 44
4.3. Clip Pit dan Topo .......................................................................................................................... 69
4.4. Membuat Waste Dump ............................................................................................................... 87
1. PENGANTAR
Pit design merupakan rencana bukaan lahan tambang yang akan digunakan untuk mengambil mineral
ekonomis yang berada dibawah tanah. Design dari pit ini harus mempertimbangkan beberapa factor penting
yaitu kualitas dan jumlah cadangan mineral, stripping ratio yang ekonomis untuk ditambang serta aspek
geoteknik dan keamanan tambang.
2. PERSIAPAN
Sebelum mulai, siapkan menu dan toolbar Block Model dan Surface Design
Setelah muncul CONS_TOPO_BEDROCK.CON pada kolom Constraint file, ceklist Inside, klik Add, maka akan
muncul kalimat pada kolom Constraint values : a. Constraint File : inside CONS_TOPO_BEDROCK.CON >
Apply
Cek hasil ore_attrribute nya pada salah satu kotak blok model ore
Dan cek juga hasil ore_attrribute nya pada salah satu kotak blok model waste
Setelah muncul CONS_TOPO_BEDROCK.CON pada kolom Constraint file, ceklist Inside, klik Add, maka akan
muncul kalimat pada kolom Constraint values : a. Constraint File : inside CONS_TOPO_BEDROCK.CON >
Apply
Setelah selesai, cek hasil file string bm_thick_ore.str yang ada pada view Surpac.
Kolom 1 = String number; Kolom 2 = Northing; Kolom 3 = Easting; Kolom 4 = Elevation; Kolom 5 atau Kolom
Deskripsi 1 = Ketebalan; Kolom 6 atau Kolom Deskripsi 2 = Nilai kadar Ni (%); Kolom 7 atau Kolom Deskripsi
3 = Aggregate Ni
Muncul window Convert Text to Column Wizard (Step 1) > Delimited > Next
Muncul window Convert Text to Column Wizard (Step 2) > Comma > Next
Muncul window Convert Text to Column Wizard (Step 3) > General > Finish
Pilih semua data tersebut sampai kebawah atau data terakhir > Cut
Melalui menu Filter, ceklah berapa nilai SR paling tinggi, dalam hal ini = 8
Import file .csv tersebut kedalam bentuk .str , File > Import > Data from one file
Ubahlah format string polyline menjadi point, dengan men drag file strings_ka_pts.tcl
Muncul window Breaks strings into points > String > Apply
Pilih stringnya
Format file string bm_thick_sr.str yang telah di break to points dalam bentuk notepad
Kemudian kita tentukan batas area kontur, menu Surface > Contouring > Contouring area > Define extents
Pada Layer containing data pilih bm_thick_sr.str > Calculated grid mesh size
Kemudian rubahlah angka grid Y dan X menjadi 10 agar lebih detil > Apply
Akan muncul batas kotak warna biru sebagai pembatas area kontur SR
Selanjutnya kita estimasin nilai SR pada masing – masing titik grid tersebut, menu Surface > Estimate grid
value > By triangulation
Muncul window Triangulation parameters, Constraint interpolation tidak perlu di ceklist > Apply
Kemudian kita buat kontur SR nya, menu Surface > Contouring > Contour grid
Masukkan Contour Definition : Interval ; Minimum contour = 0 ; Maximum contour = 10 ; Contour interval
= 0.5 > Apply
Ganti Colur : light grey ; Index Contour Properties Interval 2.5 ; Colour : red ; Draw contour value? V ;
Frequency 100 ; Size : 2 > Apply
Hasil contour SR
Miringkanlah view nya sehingga terlihat antara SR Contour dan DTM Topo
Kembalikan view ke Plan view, lalu buatlah DTM topo_ex3 lebih transparan 50%
Dengan transparan 50%, kita bisa melihat contour SR dan juga DTM topo_ex3, sehingga kita bisa memberi
Batasan rencana pit yang akan kita buat
Contoh Batasan dibawah ini yang akan kita gunakan sebagai batasan rencana ultimate pit yang akan kita buat
Ganti constraint type : Block, setelah itu pilih ni_id > 1.5 >, maka akan muncul kalimat pada kolom Constraint
values : a. Block Constraint : ni_id . 1.5 > Apply
Klik icon Start new segment for digitizing (1) lalu klik icon Create new points using the mouse (2)
2 1
Setelah mau menutup polygon, klik icon Close the current segment being digitised
Hapuskan temporary marker pada polygon tersebut icon Hide temporary marker
Pada window Enter constraints, ganti Constraint type : String ; String file : bound_pit_plan.str >
Open
Setelah string file Bound_Pit_Plan muncul, ceklist Inside, Extent : Z > Add, maka akan muncul kalimat pada
kolom Constraint values : a. String Constraint : inside Bound_Pit_Plan.str in direction Z > Apply
Matikan semua layer, sehingga hanya terlihat blok model, lalu kita rubah view menjadi Section View
Cek lah elevasi terendah dari blok model yang masih masuk kedalam kumpulan yang banyak, contoh
dibawah ini adalah elevasi 126 m
Lalu kita batasi blok model yang akan ditampilkan hanya dari elevasi 126 – 132 m, dengan asumsi
dalam hal ini tinggi bench yang akan kita buat adalah 6 m.
Ganti Constraint type : Z Plane ; Z = 126 ; Above (√) > Add lalu Z = 132 ; Above ( ) > Add, sehingga
pada kolom Constraint values : a. Z Value Constraint : above Z = 126 ; b. Z Value Constraint : Not
above Z = 132 > Apply
Klik icon Start new segment for digitizing (1) lalu klik icon Create new points using the mouse (2)
2 1
Tentukan pit slope gradient, menu Design > Pit design > Set slope gradient
Muncul window Set the design gradient, Ganti unit : angle ; Gradient = 60 > Apply
Pada window Expand segment by bench height, Bench Height = 6 ; Limiting elevation = 9999 ; Z
direction : up ; Horizontal direction : expand > Apply
Dalam contoh ini kita asumsikan berm width 2 m, pada window Expand Segment by Berm Width
Default berm width = 2 ; Berm gradient (%) = 0 ; Horizontal direction : expand > Apply
Setelah selesai pembuatan bench level 126 – 132, kita kembalikan blok model seperti sebelumnya,
icon Remove last graphical constraint
Ganti Constraint type : Z Plane ; Z = 132 ; Above (√) > Add lalu Z = 138 ; Above ( ) > Add, sehingga
pada kolom Constraint values : a. Z Value Constraint : above Z = 132 ; b. Z Value Constraint : Not
above Z = 138 > Apply
Selanjutnya kita geser polygon berm atau toe level 132 m, agar blok model level 132 – 138 m bisa
tertambang
Klik dekat point, dan tahan, lalu drag kearah blok model yang akan ditambang
Kalau masih kurang pas, kita bisa geser lagi, Move point
Pada window Expand segment by bench height, Bench Height = 6 ; Limiting elevation = 9999 ; Z
direction : up ; Horizontal direction : expand > Apply
Default berm width = 2 ; Berm gradient (%) = 0 ; Horizontal direction : expand > Apply
Ulangi langkah – langkah tersebut sampai level blok model tertinggi dan melewati topografi tertinggi
di area pit tersebut.
Cek bench dari pit sudah melebihi dari topografi sekitar pit
Buatlah DTM dari file pit_ex3_v1.str, Surface > DTM File functions > Create DTM from string file
Untuk memotong kelebihan dari DTM pit_ex3_v1, kita gunakan menu Surfaces > Clip or intersect
DTMs > Line of intersection between DTMs
Garis polygon merah hasil intersect antara DTM topo_ex3 dan DTM pit_ex3_v1
Matikan layer DTM topo_ex3 dan DTM pit_ex3_v1, lalu cek lah polygon hasil intersect nya, jika ada
segment yang berada didalam atau diluar dari polygon utama, maka kita hapus saja segment
tersebut, icon Delete segment.
Pilih segment yang terpisah dari polygon utama hasil intersect topo_ex3 dan pit_ex3_vq, klik pada
segment tersebut.
Setelah kita delete semua segment yang berada diluar atau didalam polygon utama, lalu kita save
file intersect_topo_pit_v1.str
Pada window Select and clip data > Outside the boundary > Apply
Setelah dipilih polygonnya, maka segment dari pit_ex3_v1.str yang berada diluar batas polygon
intersect_topo_pit_v1.str akan terpotong.
Save lah file string pit_ex3_v1 yang telah di clip tadi dengan nama file lain,
Contohnya kita namakan dengan pit_ex3_v1_clip.str, untuk membedakan dengan file pit_ex3_v1.str
yang belum di clip.
Untuk membentuk DTM pit yang sudah di clip, kita harus membuat lagi DTMnya, namun sebelum
itu kita siapkan string gabungan / merge antara file pit_ex3_v1_clip.str dengan file
intersect_topo_pit_v1.str, dengan cara memilih kedua file tersebut sambal menekan tombol Ctr, lalu
drag kedua file tersebut kedalam monitor Surpac.
Buatlah file DTM dari string pit_ex3_v1_clip.str , Surface > DTM File functions > Create DTM from
string file
Pada window Create a DTM from a string file, ketikan atau pilih
Location : pit_ex3_v1_clip ; Object ID : 5
Strings to act as break lines (√) ; Would you like to clip the DTM to boundary after creation? (√) ;
Location : intersect_topo_pit_v1 ; String : 108 > Apply
Selanjutnya kita akan meng clip string topo_ex3.str yang berada didalam string boundary
intersect_topo_pit_v1.str.
Tampilkan dalam layer file string topo_ex3.str dan intersect_topo_pit_v1
Pada window Select and clip data : inside the boundary > Apply
Setelah dipilih polygonnya, maka segment dari topo_ex3.str yang berada didalam batas polygon
intersect_topo_pit_v1.str akan terpotong.
Save lah file string topo_ex3 yang telah di clip tadi dengan nama file lain,
Untuk membuat file DTM topo_ex yang sudah di clip, maka kita siapkan string gabungan / merge
antara file topo_ex3_clip_pit_v1.str dengan file intersect_topo_pit_v1.str, dengan cara memilih
kedua file tersebut sambal menekan tombol Ctr, lalu drag kedua file tersebut kedalam monitor
Surpac.
Buatlah file DTM dari string topo_ex3_clip_pit_v1.str , Surface > DTM File functions > Create DTM
from string file
Pada window Create a DTM from a string file, ketikan atau pilih
Location : topo_ex3_clip_pit_v1 ; Object ID : 1
Strings to act as break lines (√) ; Would you like to clip the DTM to boundary after creation? (√) ;
Location : intersect_topo_pit_v1 ; String : 108 > Apply
Kemudian muncul window Extract contours from a DTM, isikan atau pilih
DTM from which contours will be extracted > Location : topo_ex3; Field to contour : z; Object ID :
1; Trisolation ID : 1
Define contours by > (√) Interval ; Minimum contour = 70 ; Maximum contour = 336 ; Contour
interval = 2
Define the contour string file > Location : topo_ex3_cont ; Define plot enhancement requirements
> (√) Create index contour file ; Location : topo_ex3_cont10 ; Index value = 10
Setelah selesai membuat contour, maka kita lanjutkan untuk membuat waste dump. Dimana waste dump ini
akan digunakan untuk menimbun material overburden atau waste yang tidak bisa digunakan atau dijual.
Buatlah layer baru, Layers > New , pada window Create a new layer Name : bound_wd_plan
Buatlah layer baru, Layers > New , pada window Create a new layer Name : wd_ex3_v1
Kita mulai digitasi dari level yang agak bawah dulu, yaitu level 150
Enter / Change digitizer point attributes, String # = 11 ; Z = 150
Kita mulai digitasi pada level 170 m, bagian bawah dari waste dump.
Pada window Set the design gradient Unit : angle ; Gradient = 40 ; Angel units : decimal degrees >
Apply
Dalam hal ini kita buat kearah bawah dulu, atau kearah toe waste dump
Pada window Expand segment by bench height, Bench Height = 5 ; Limiting elevation = -9999 ; Z
direction : down ; Horizontal direction : expand > Apply
Pada window Expand Segment by Berm Width, Default berm width = 10 ; Berm gradient (%) = 0 ;
Horizontal direction : expand
Selanjutnya kita buat kaki toe paling bawah dari waste dump ini, sampai toe nya dibawah permukaan
tanah, icon Expand segment by bench height
Untuk itu kita coba expand sampai 15 m kearah bawah, Bench height = 15 ; Limiting elevation -9999
; Z direction : down ; Horizontal direction : expand
Setelah toe waste dump paling bawah selesai, kita lanjutkan kearah atas.
Untuk itu kita coba expand by bench height kearah atas, Bench height = 5 ; Limiting elevation 9999
; Z direction : up ; Horizontal direction : contract > Apply
Minetech Indonesia Page 97
Tutorial Surpac 6 – Pit & Dump Design 2020
Setelah naik bench, lanjutkan berm, dengan expand segment by berm width
Pada window Expand Segment by Berm Width, Default berm width = 25 ; Berm gradient (%) = 0 ;
Horizontal direction : contract
Selanjutnya kita buatkan file DTM nya, menu Surface > DTM file function > Create DTM from string
file
Selanjutnya kita potong pertemuan antara DTM wd_ex3_v1.dtm dengan DTM topo_ex3.dtm
Kita clip file string waste dumpnya, Edit > Trim > Clip by selected segment
Pada window Select and clip data : Outside the boundary > Apply
Save lah file waste dump hasil clip, Layers > Save layer
Pada window Save File, kita bedakan namanya menjadi File name : wd_ex3_v1_clip.str > Apply
Kita reset graphic window Surpac, drag lah file intersect_topo_wd_ex3_v1.str dan wd_ex3_v1_clip
Lalu kita save lagi file nya, Layers > Save layer
Pada window Create a DTM from a string file, ketikan atau pilih
Location : wd_ex3_ v1_clip ; Object ID : 6
Strings to act as break lines (√) ; Would you like to clip the DTM to boundary after creation? (√) ;
Location : intersect_topo_wd_ex3_v1 ; String : 109 > Apply
Kita coba clip lagi file DTM topo_ex3.dtm dengan file string wd_ex3_v1_clip.str Dari menu Edit >
Trim > Clip by selected segment
Pada window Select and clip data : inside the boundary > Apply
Save file kedua segment hasil intersect topo tersebut menjadi file baru, window Save File ; File name
: intersect_topo_pit_v1_wd_v1.str > Apply
Buatlah DTM topo_ex3 yang sudah di clip oleh pit_ex3_v1 dan wd_ex3_v1
Pada window Create a DTM from a string file, ketikan atau pilih
Location : topo_ex3_clip_pit_v1_wd_v1 ; Object ID : 1
Strings to act as break lines (√) ; Would you like to clip the DTM to boundary after creation? (√) ;
Location : intersect_topo_pit_v1_wd_v1 ; String : 109 > Apply