DIRECTOR
DIRECTOR
Muhammad Ikhwan Bin Abdul Razif
Wan Mohd Sabri Bin Wan Mohd Noor
Dip. Offshore Engineering
Bach. Hons Accounting
GENERAL MANAGER
Ahmad Hilmi Hanif Bin Abdul Halim
Dip. Production (Tool & Die)
* FAKTOR JISIM
* KETAHANAN YANG TINGGI
* KALIS AIR
* KESESUAIAN
DALAM PELBAGAI KEADAAN
MENGENAI
PVC FOAM BOARD
* BIODEGRASI
* KETAHANAN TERHADAP CUACA
* PENEBAT YANG EFEKTIF
10MM, 15MM,
THICKNESS 20MM, 25MM
CERTIFICATE ISO
Penggunaan
Pemakuan, gam, pengerudian, laluan pemotongan boleh menggunakan alat
biasa.
Kebolehan Mengecat
Disebabkan permukaan yang rata, ia adalah produk yang sangat sesuai untuk
dicat.
Pembersihan
Merupakan produk yang sangat mudah untuk dibersihkan.
Metal Wood
Acrylic GFRC
BAHAN
PEMASANGAN
BAHAN
KEKEMASAN
SOLIDPRO
A High Strength Acrylic Polymer Coating for Concrete
And Metal
DESCRIPTION
SOLIDPRO is a single pack, solvent borne, acrylic resin
based surface sealer and dustproofer for concrete.
When applied to freshly placed concrete. SOLIDPRO
functions as a curing membrane, reducing any
tendency towards drying shrinkage cracks. At the same
time the surface becomes sealed against the ingress of
oils and many aqueous chemical and a hard wearing
floor is produced. When applied to old / aged concrete
floors, SOLIDPRO penetrates into the pore structure
thereby sealing and dust-proofing the surface. Having
excellent adhesion to concrete, SOLIDPRO allows the
application of subsequent paint / coating treatments,
thereby minimizing surface preparation requirements.
BENEFITS
> Ready to use can easily be applied by brush or
roller.
> Good chemical and abrasion resistance.
> Seals and dust proofs the surface.
> Compatible with most substrate finishes.
> Provides easily cleanable floor surfaces.
> Internal and external use. HOW TO USE
> Resistant to ultra violet radiation.
> Excellent adhesion to concrete and masonry Surface Preparation :
A) Old concrete shall be sound and free from oil,
surfaces.
grease, laitance and other contaminates. Previously
> Applicable on aluminium composite panels.
applied paint or curing membrane must be
removed. Wash the floor with a detergent solution
USES followed by clean water, and then allow to dry prior
to sealer application.
As a curing and sealing treatment to new concrete and B) Over new concrete SOLIDPRO may be applied 15
as a sealing and / dust-proofing treatment to old minutes after the final finish.
concrete, to provide a sealed and dust proof surface
with resistance to the ingress of oil and chemical Application :
spillages. As a primer / sealer for subsequent to top A) Over old concrete, apply a coat of SOLIDPRO by
coating. brush or roller, squeegee or spray at a nominal rate
of 8 ~ 10 m² < / litre. Avoid the formation of
Where to Use : Industrial workshops, car parks, puddles of excess material, after a minimum period
warehouses, food preparation areas, garages etc. of 12 hours a second coat shall be applied at a rate
of 12 ~ 14 m² < / litre.
B) Over new concrete apply SOLIDPRO by spray at
PACKING & DOSAGE nominal rate of 6 ~ 8 m² < / litre. Ensure that the
material is applied evenly and avoid the formation
5 liters and 20 litres in aluminium pail, coverage is very of puddles of excess material on the surface. In hot
much dependent on the porosity of the substrate. For or windy conditions a second coat of SOLIDPRO
new concrete apply first coat at the rate of 5 m² < / litre should be applied on following day at a nominal
to eliminate the curing process 2 ~ 3 coats in rate of 8 ~ 10 m² < / litre.
recommended to give perfect sealing / curing and
abrasion resistant for smooth old concrete surface. Cleaning :
Coverage will be 10 ~ 12 m² < / litre. Clean all equipments using thinner.
Drying / Curing :
SOLIDPRO will be tack free in 2 ~ 4 hours and hard dry
after 20 ~ 24 hours in conditions of good ventilation.
BAHAN
FILLER
A ready mixed, easy-to-use multipurpose filler specially formulated to fill cracks
and holes in single application. It has virtually no shrinkage and is smooth and
durable. It is paintable with oil and water-based paints. This water-based filler can
be cleaned up with water easily.
CARA
PEMASANGAN
MS PLATE 25x3.0
CARA
PEMASANGAN
WALLPLUG
DETAIL A
WALLPLUG
M 10 STAINLESS STEEL
M 10 SKRU KONKRIT KELULI TAHAN KARAT
DETAIL A
246
APLIKASI
PVC FOAM BOARD
APLIKASI
PVC FOAM BOARD
APLIKASI
PVC FOAM BOARD
APLIKASI
PVC FOAM BOARD
PVC FOAM BOARD
CUT OUT DEMO
*VOLUMIZED DESIGN
*PATTERN CUT OUT DESIGN
DESIGN PROCESS
01 QUOTATION
PROPOSAL TO
CLIENT 02
DESIGN CHECKING
03 ▶ Template making
▶ Machine drawing
sorting
WANS LEGACY
04
▶ Material
▶ Thickness
▶ Finishes
▶ Design etc.
PRODUCTION
PROCESS
CNC MACHINE
Send drawing to 01
machine
SANDING
02 Cutting process
(duration according to
design)
FINISHING
Process of smoothing 03
surfaces & holes
WRAPPING
▶ Double check panels
04 with drawing
▶ Approval of all
according to specs.
DELIVERY
Wrapping with plastic
sheet to protect the
05
product
INSTALLATION
06 ▶ Transportation
▶ Postage
TOUCH UP
▶ Method of Installation
▶ Attachment or see
07
through
COMPLETE
08 ▶ Filler
▶ Paint
CONTOH PROPOSAL
CONTOH PROPOSAL
PROJEK
SEDANG BERJALAN