Potential difference between two points can be defined as the work done in moving a unit
charge from one point to another point in an electric field.
Beza keupayaan antara dua titik boleh ditakrifkan sebagai kerja yang dilakukan untuk memindahkan 1
unit cas dari satu titik ke titik lain dalam medan elektrik.
Electromotive force (E.M.F), E is the total energy supplied by a cell to move a unit of
electrical charge from one terminal to the other through the cell and the external circuit.
Daya gerak elektrik (D.G.E), E ialah jumlah kerja yang dilakukan oleh suatu sumber elektrik untuk
menggerakkan 1 coulomb cas menggelilingi litar lengkap.
Part of the cell’s e.m.f is used in the cell to overcome the internal resistance of the cell when
the cell is supplying current to an external load such as a light bulb.
Sebahagian d.g.e sel digunakan dalam sel untuk mengatasi rintangan dalam sel apabila sel
membekalkan arus ke satu beban luar seperti mentol lampu.
Internal resistance, r is the resistance within a cell or source of electricity due to its
electrodes.
Rintangan dalam, r adalah rintangan dalam ssel atau sumber elektrik disebabkan oleh elektrodnya.
42
TO INVESTIGATE THE RELATIONSHIP BETWEEN CURRENT AND POTENTIAL
DIFFERENCE FOR AN OHMIC CONDUCTOR
UNTUK MENYIASAT HUBUNGAN ANTARA ARUS DAN BEZA KEUPAYAAN UNTUK KONDUKTOR
OHM
43
EXAMPLE / CONTOH
1. Figure below shows a simple circuit consisting of a 2 V dry cell with an internal resistance of
0.5 Ω. When the switch is closed, the ammeter reading is 0.4 A. Calculate
Rajah di bawah menunjukkan suatu litar ringkas mengandungi sel kering 2 V dengan rintangan dalam
0.5 Ω. Apabila suis ditutup, bacaan ammeter adalah 0.4 A. Hitung
a) The resistance , R,
Rintangan, R,
b) The voltmeter reading in closed circuit.
Bacaan voltmeter jika litar tertutup.
2. A voltmeter registers a reading of 1.5 V when it is connected directly to a dry cell. When a
resistor, R is connected to the cell, the voltmeter reading decreases to 1.4 V. The current
flowing is 0.2 A. Calculate
Suatu voltmeter menunjukkan bacaan 1.5 V apabila ia disambung terus dengan sel kering. Apabila satu
perintang, R disambung dengan sel, bacaan voltmeter menurun ke 1.4 V. Arus mengalir adalah 0.2 A.
Hitung
a) The internal resistance of the cell, r
Rintangan dalam sel, r
b) The value of R.
Nilai R
44
3. When a battery with an electromotive force, E and internal resistance, r is connected to a 2
Ω resistor, the current flow is 0.6 A. When the 2 Ω resistor is replaced by a 7 Ω resistor, the
current flow is 0.2 A. Calculate
Apabila suatu bateri dengan daya gerak elektrik, E dan rintangan dalam, r disambung kepada perintang
2 Ω, aliran arus adalah 0.6 A. Apabila perintang 2 Ω diganti dengan perintang 7 Ω, aliran arus adalah 0.2
A. Hitung
a) The internal resistance, r
Rintanagn dalam, r
b) The value of E.
Nilai E
4. Three resistors are connected to a 3 V battery as shown in figure below. The internal
resistance of the battery is 1 Ω .What is the voltmeter reading?
Tiga perintang disambung kepada satu bateri 3 V sperti ditunjukkan di rajah bawah. Rintangan dalam
bateri adalah 1 Ω. Berapakah bacaan voltmeter?
45
EXERCISE / Latihan
Paper 1 / Kertas 1
1. The diagram shows a resistor of resistance
4Ω connected to a battery.
Rajah di bawah menunjukkan suatu perintang
dengan rintangan 4 Ω disambung kepada satu
bateri.
46
From the results of the experiment, a graph
of potential difference V against current I is
plotted.
Dari keputusan eksperimen, satu graf beza
keupayaan V melawan arus I diplotkan.
The internal resistance of the battery is …
Which of the following has the correct Rintangan dalam bateri adalah …
value of the e.m.f and internal resistance of A. 0.20 Ω
the cell? B. 0.40 Ω
Antara berikut yang mana mempunyai nilai yang
betul tentang d.g.e dan rintangan dalam sel?
C. 0.45 Ω
E.m.f. ,E Internal resistance, D. 0.80 Ω
D.g.e. ,E r E. 1.20 Ω
Rintangan dalam, r
A. a b/a 7. The diagram shows a battery of e.m.f 5.0 V
B. a a/b and internal resistance 3.0 Ω connected to
C. b b/a two resistors.
Rajah menunjukkan suatu bateri dengan d.g.e.
D. b a/b 5.0 V dan rintangan dalam 3.0 Ω disambung
kepada dua perintang
5. Voltmeter V has infinite resistance and
ammeter A has negligible resistance. Which
circuit can be used to measure the
electromotive force of a battery?
Voltmeter V mempunyai rintanagn infiniti dan
ammeter A mempunyai rintangan yang boleh
diabaikan. Litar yang mana boleh digunakan
untuk mengukur daya gerak elektrik bateri? What is the voltage across the battery?
A. B. Berapakah voltan merentasi bateri ?
A. 0.75 V
B. 1.75 V
C. 2.5 V
D. 4.25 V
C. D. 8. A cell of e.m.f 12 V and internal resistance
0.4 Ω is connected to a bulb. The current
in the circuit is 5 A. What is the resistance
of the bulb?
Suatu sel dengan d.g.e 12 V dan rintangan
dalam 0.4 Ω disambung kepada satu mentol.
Arus yang mengalir adalah 5 A. berapakah
6. In the circuit of diagram below the reading rintangan mentol?
of the voltmeter is 6.0 V when switch S is A. 1.0 Ω
open. When switch S is closed, the B. 2.0 Ω
voltmeter reads 5.6 V and the ammeter C. 3.0 Ω
reads 0.5 A. D. 4.0 Ω
Di Rajah litar di bawah, bacaan voltmeter adalah
6.0 V apabila suis S dibuka. Apabilia suis S
ditutup, bacaan voltmeter adalah 5.6 V dan
bacaan ammeter adalah 0.5 A.
47
9. The diagram shows an arrangement of 11. Diagram below shows a battery with
resistors being connected to a battery e.m.f., E = 6 V, and internal resistance, r =
having e.m.f of 6 V and internal resistance 2 Ω connected to resistor 12 Ω and R Ω in
of 2 Ω. series.
Rajah menunjukkan susunan perintang Rajah di bawah menunjukkan suatu bateri
disambung kepada bateri yang mempunyai d.g.e dengan d.g.e., E = 6 V dan rintangan dalam, r =
6 V dan rintangan dalam 2 Ω. 2 Ω.
48
EXERCISE / Latihan
Paper 2 – Section A / Kertas 2 – Bahagian A
1. Graph in figure (a) shows graph of potential difference against current for electrical circuit
figure (b).
Graf di rajah (a) menunjukkan graf beza keupayaan melawan arus untuk litar elektrik rajah (b)
………………………………………………………………………………………………………………………………………………………..
b) Calculate the internal resistance of the batteries in the circuit.
Hitung rintangan dalam bateri pada litar di atas.
e) If we connect another resistor parallel to resistor, R the reading of the voltmeter will
decrease. Explain.
Jika kita menyambungkan perintang lain selari dengan perintang, R bacaan voltmeter akan
berkurang. Jelaskan.
………………………………………………………………………………………………………………………………………………………..
……………………………………………………….……………………….………………………………………………………………………
49
2. Figure below shows a simple circuit consisting of 4 dry cells of 1.5 V each and an internal
resistance of 0.5 V each. When the switch is closed the ammeter reading is 1.2A.
Rajah di bawah menunjukkan suatu litar ringkas mengandungi 4 sel kering 1.5 V setiap satu dan
rintangan dalam 0.5 V setiap satu. Apabila suis ditutup, bacaan ammeter adalah 1.2 A.
………………………………………………………………………………………………………………………………………………………..
……………………………………………………….……………………….………………………………………………………………………
b) Calculate
Hitung
i) The resistance, R
Rintangan, R
50
ELECTRICITY Analysing Electrical Energy and Power
ELEKTRIK Analisa Tenaga Elektrik dan Kuasa
2.5
Some appliance that is made of metal need to use three pin plug with the earth wire
connected from the body of the appliance to the ground to avoid electrical shock to user.
Sesetengah perkakas diperbuat daripada logam perlu menggunakan palam tiga pin dengan wayar bumi
disambung daripada perkakas ke bumi untuk mengelakkan kejutan elektrik kepada pengguna.
The power rating of an appliance denotes the rate at which it consumes electrical energy.
For example, a 2000W hair dryer uses 2000J of electrical energy per second.
Kadar kuasa perkakas menandakan kadar penggunaan tenaga elektrik. Sebagai contoh, pengering
rambut 2000W menggunakan 2000J tenaga elektrik sesaat.
51
Energy Usage / Penggunaan Tenaga
The use of electrical energy must be paid for and the cost depends on the total quantity of
energy consumed in a given period.
Penggunaan tenaga elektrik mesti dibayar dan kos bergantung dengan jumlah kuantiti tenaga
digunakan dalam tempoh yang diberi.
Conversion of energy takes place in an electrical circuit. In the process of conversion, electrical energy
input is converted into the form of energy that is required as output. However, a portion of the energy
output is lost to the surroundings as heat, sound or others.
Penukaran tenaga mengambil tempat dalam litar elektrik. Dalam proses penukaran, tenaga elektrik
input ditukar ke dalam bentuk tenaga yang diperlukan sebagai output. Walau bagaimanapun,
sebahagian tenaga output hilang ke persekitaran sebagai haba, bunyi atau lain.
52
Fuse / Fuis
A fuse is a short piece of thin wire which overheats and melts if current of more than a
certain value flows through it.
Fius adalah wayar nipis yang pendek yang akan jadi terlampau panas dan cair jika arus yang melebihi
nilai tertentu mengalir melaluinya.
A fuse is made of fine tin or lead wire which has a low melting point and low heat capacity.
Fius diperbuat daripada timah halus atau plumbum yang mempunyai takat lebur rendah dan muatan
haba rendah.
The fuse suitable for use in appliance must be slightly higher than the normal current flowing
through the appliance.
Fius yang sesuai untuk digunakan dalam perkakas mesti lebih tinggi berbanding dengan arus normal
yang mengalir melalui perkakas.
Example if the current required for the appliance in normal use is 5.2A, the suitable fuse is
6A fuse.
Contoh jika arus yang diperlukan untuk perkakas dalam penggunaan normal adalah 5.2A, fuis sesuai
adalah fius 6A.
Plugs /Soket
Earth wire is a safety wire that is connected to the metal part of the appliance. If a live wire
touches the metal body of the appliance, a large current would immediately flow to the
earth and breaks the fuse. This will prevent a person from electrocution if he touches the
faulty appliance.
Wayar bumi adalah wayar keselamatan yang disambung kepada bahagian logam perkakas. Jika wayar
bumi menyentuh badan logam perkakas, arus yang tinggi akan mengalir ke bumi serta-merta dan
mencairkan fuis. Ini akan mengelakkan pengguna dari kejutan elektrik jika menyentuh perkakas yang
rosak.
53
Filament Lamp / Lampu Filamen
The filament in a bulb is made of fine coil of tungsten wire. Tungsten is used as it has a high
melting point and high resistivity.
Filamen dalam mentol diperbuat daripada gegelung halus wayar tungsten. Tungsten digunakan kerana
ia mempunyai takat lebur tinggi dan rintangan tinggi
When a current passes through the filament it becomes white hot and light is produced.
Apabila arus mengalir melalui filament, ia menjadi putih panas dan cahaya dihasilkan.
The filament is placed inside a glass bulb filled with argon and nitrogen gas at low pressure.
These inert gases help to prevent the filament from melting at high temperature.
Filamen diletakkan dalam mentol kaca yang berisi dengan gas argon dan nitrogen pada tekanan rendah.
Gas ini membantu menghalang filament daripada lebur pada suhu tinggi.
Electric current through the heating element encounters resistance, resulting in heating of
the element.
Arus elektrik mengalir melalui elemen pamanas mengalami rintangan, mengakibatkan elemen jadi
panas.
Nichrome is widely use as heating element because of high resistivity and high melting point.
Nikrom banyak digunakan sebagai elemen pemanas kerana mempunyai rintangan tinggi dan takat lebur
yang tinggi.
54
EXAMPLE / CONTOH
1. Figure below shows three resistors L,M and N connected to a battery with an internal
resistance of 1 Ω. Calculate
Rajah di bawah menunjukkan tiga perintang L, M dan N disambung kepada satu bateri dengan
rintangan dalam 1 Ω. Hitung
a) The ammeter reading,
Bacaan ammeter
b) The energy dissipated by the resistor M
in 2 minutes.
Tenaga dilesapkan oleh perintang M dalam
masa 2 minit.
2. Figure below shows a battery of negligible internal resistance, connected to two lamps X and
Y with power ratings of 12 V, 12 W respectively. The resistance of the filaments of X and Y
are R1 and R2 respectively. Calculate
Rajah di bawah menunjukkan suatu bateri dengan rintangan dalam yang boleh diabaikan, disambung
kepada dua lampu X dan Y dengan kadar kuasa 12V, 12 W masing-masing. Rintanagn filament X dan Y
adalah R1 dan R2 masing-masing. Hitung
a) The ratio I1 : I2
Nisbah I1 : I2
b) The ratio R1:R2
(Assume that resistance does not depend on
temperature)
Nisbah R1 : R2
(Andaikan rintangan tidak bergantung pada suhu)
55
4. Figure below shows a lamp with two filaments P and Q rated at 50 W and 100 W
respectively. The circuit of each filament can be closed independently.
Rajah di bawah menunjukkan suatu lampu dengan dua filament P dan R berkadar pada 50 W dan 100 W
masing-masing. Litar untuk setiap filament boleh ditutup secara berasingan.
a) Why are two filaments connected in parallel?
Mengapakah dua filament disambung secara selari?
b) What is the cost of using the lamp at its brightest for
1 hour? The cost of electricity is 21.8 cents for first
200 units.
Berapakah kos penggunaan lampu itu selama 1 jam? Kos
elektrik adalah 21.8 sen untuk 200 unit yang pertama.
5. An electric motor is used to lift a load of mass 600 g to a height of 5 m in 8 s. If the supply
voltage is 10 V and the flow of current in the motor is 0.6 A, calculate the efficiency of the
motor.
Sebuah motor elektrik digunakkan untuk mengangkat beban berjisim 600g ke ketinggian 5m dalam 8s.
Jika bekalan voltan adalah 10V dan aliran arus dalam motor adalah 0.6A, hitung kecekapan motor itu.
6. A tungsten-filament lamp and a fluorescent lamp, each with a power rating of 40 W, produce
8 W and 38 W of light energy respectively. What is the efficiently of each lamp?
Lampu filament tungsten dan lampu neon, setiap satunya dengan kadar kuasa tercatat 40 W,
menghasilkan 8 W dan 38 W tenaga cahaya masing-masing. Berapakah kecekapan setiap lampu?
56
EXERCISE / Latihan
Paper 1 / Kertas 1
1. A 40 W fluorescent lamp transfer 60 % of 5. An electric motor connected to a 240 V
the electrical energy to light energy. How supply draws a current of 2.5 A from the
much light energy does it emit in two supply when it is lifting a load of 20 kg as
minutes? shown in diagram below.
Suatu lampu neon 40 W memindahkan 60% Suatu motor elektrik disambung kepada satu
tenaga elektrik menjadi tenaga cahaya. bekalan 240 V menggunakan arus 2.5 A dari
Berapakah tenaga cahaya yang ia pancarkan bekalan apabila ia mengangkatkan suatu beban
dalam masa dua minit? 20 kg seperti ditunjukkan di Rajah bawah.
A. 2.88 kJ
B. 3.22 kJ
C. 4.55 kJ
D. 6.33 kJ
57
7. A fluorescent lamp used in a normal 10. Two filament bulbs P and Q are labelled
household has a power of 40 W. If the cost “12 V, 6 W” and “12 V, 24 W “respectively
each unit of electrical energy used is 20 and are connected in parallel to a 12 V
cents, what is the cost of switching on the power supply as shown in the diagram
fluorescent lamp for 20 hours? below.
Lampu neon digunakan dalam rumah biasanya Dua mentol filamen P dan Q dilabelkan “12 V, 6
mempunyai kuasa 40 W. Jika kos unit tenaga W” dan “12 V, 24 W” masing-masing dan
elektrik adalah 20 sen seunit, berapakah kos disambungkan secara selari kepada bekalan
lampu neon itu untuk 20 jam? kuasa 12 V seperti ditunjukkan dalam rajah di
A. 1.6 cents / 1.6 sen bawah.
B. 16 cents / 16 sen
C. RM 1.60
D. RM 16.00
E. RM 160.00
Which observation below is not true?
8. Table below shows the electricity tariff for
Pemerhatian di bawah yang mana tidak benar?
an office.
A. Bulb Q is brighter than bulb P.
Jadual di bawah menunjukkan tariff elektrik
Mentol Q lebih terang daripada mentol P.
untuk sebuah pejabat.
B. The current passing through bulb Q is
Unit of electricity Cost per unit bigger.
Unit elektrik Kos per unit Arus mengalir melalui mentol Q lebih
First 100 unit 23 cents besar.
100 unit pertama 23 sen C. Resistance of bulb P is lower than
Next 500 unit 25 cents that of bulb Q.
500 unit seterusnya 25 sen Rintangan mentol P lebih rendah daripada
Other higher unit 29 cents mentol Q.
Unit lain lebih tinggi 29 sen D. Bulb Q produces more heat per
second than bulb P.
Find the cost of using an air-conditioner of Mentol Q menghasilkan lebih banyak haba
power 2.0 kW for 255 hours. sesaat daripada mentol P.
Cari kos penggunaan penghawa dingin berkuasa
2.0 kW untuk 255 jam. 11. Three bulbs P, Q and R are connected in
A. RM 102.00 B. RM 117.30 series to a12 V battery as shown in
C. RM 125.50 D. RM 127.50 diagram below.
E. RM 135.00 Tiga mentol P, Q dan R disambung secara sesiri
dengan bateri 12 V seperti ditunjukkan di rajah
9. Among the following, which is the main bawah.
characteristic of the heating element in an
electric kettle?
Antara berikut, yang mana adalah ciri utama
elemen pemanas dalam sebuah cerek elektrik?
A. High resistivity Which bulbs are the brightest?
Kerintangan tinggi Mentol yang mana adalah paling terang?
B. Low melting point A. P B. R
Takat lebur rendah
C. Q and R D. All the bulbs have
C. Becomes brittle at high temperature Q dan R the same brightness
Menjadi rapuh pada suhu tinggi
Semua mentol
D. Readily oxidized at high temperature mempunyai kecerahan
Mudah teroksida pada suhu tinggi yang sama.
58
12. Three resistors with resistance of 5 Ω, 10 13. Four resistors are connected as shown in
Ω and 15 Ω are connected to a D.C supply diagram below.
as shown in diagram below. Empat perintang disambung seperti ditunjukkan
Tiga perintang dengan rintangan 5 Ω, 10 Ω dan di rajah bawah.
15 Ω disambung kepada satu bekalan A.T
seperti ditunjukkan pada rajah bawah
The current passing through the ammeter When the switch is closed, which resistor
is 3 A. What is the power dissipated by the will dissipate heat at the highest rate?
5 Ω resistor? Apabile suis ditutup, perintang yang mana akan
Arus mengalir melalui ammeter adalah 3 A. melesapkan haba pada kadar yang paling
Berapakah kuasa dilesapkan oleh perintang 5Ω? tinggi?
A. 5W A. R1
B. 10 W B. R2
C. 15 W C. R3
D. 20 W D. R4
E. 40 W
59
EXERCISE / Latihan
Paper 2 – Section A / Kertas 2 – Bahagian A
1. Figure below shows an immersion heater rated as 240 V, 2kW.
Rajah di bawah menunjukkan suatu pemanas rendam berkadar 240 V, 2kW.
a) Explain what is meant by the label “240 V, 2kW” of the immersion heater.
Jelaskan apa yang dimaksudkan oleh label “240 V, 2 kW” pemanas rendam.
……………………………………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………………………………
b) The heating element of the immersion heater is nichrome. Give a reason why nichrome
is used.
Elemen pemanas untuk pemanas rendam adalah nikrom. Mengapakah nikrom digunakkan.
……………………………………………………………………………………………………………………………………………………………
……………………………………………………………………………………………………………………………………………………………
c) If the immersion heater is connected to a 240 V supply, calculate the current that passes
through the immersion heater.
Jika pemanas rendam disambung kepada suatu bekalan 240 V, hitung arus yang mengalir melalui
pemanas rendam.
e) If the immersion heater is connected to a 110 V supply, what will be the heating power
of the immersion heater?
Jika pemanas rendam disambung dengan suatu bekalan 110 V, berapakah kuasa pemanasan
pemanas rendam?
60
2. Diagram below shows the typical electrical wiring system in a house.
Rajah di bawah menunjukkan sistem pendawaian elektrik tipikal dalam sebuah rumah.
a)
i) State whether the lighting circuit is connected in parallel or in series.
Nyatakan sama ada litar lampu disambung secara selari atau sesiri.
………………………………………………………………….…………………………………………………………………………
ii) State the main difference between the lighting circuit and the power circuit.
Nyatakan perbezaan utama antara litar lampu dan litar kuasa.
………………………………………………………………….…………………………………………………………………………
……………………………………………………………………………………………….……………………………………………
b) An electric iron is labelled “240 V, 2kW”.
Seterika elektrik dilabel “240 V, 2 kW”.
i) Calculate the current flowing through the iron when it is used.
Hitung arus yang mengalir melalui seterika apabila digunakan.
ii) You are provided with the following fuses: 5 A, 8 A, 13 A, 20 A. which fuse is
suitable to be used in the circuit of the electric iron? Explain your answer.
Anda dibekalkan dengan fuis berikut: 5 A, 8 A, 13 A, 20 A. Fuis yang man sesuai untuk
digunakan dalam litar seterika elektrik? Jelaskan jawapan anda.
………………………………………………………………….…………………………………………………………………………
……………………………………………………………………………………………….……………………………………………
………………………………………………………………….…………………………………………………………………………
iii) Give the name of the metal which is usually used to construct the heating
element of the iron.
Berikan nama logam yang sering digunakan untuk membina elemen pemanasan seterika.
………………………………………………………………….…………………………………………………………………………
61
Electrical Appliance Power ratings Number of units Time used/per day
Perkakas elektrik Kadar kuasa Nombor unit Masa penggunaan /
Setiap hari
Filament lamp 80 W 4 10
Lampu filamen
Fridge 400 W 1 12
Peti sejuk
Television 500 W 1 8
Televisyen
Kettle 2 kW 1 2
Cerek
c) The above table shows that the number of units and the duration of use of each electrical
appliance in a house per day. The tariff and the rates of electrical energy charges are shown
in the table below.
Jadual di atas menunjukkan bilangan unit dan tempoh penggunaan setiap perkakas elektrik dalam
sebuah rumah setiap hari. Caj tarif dan kadar tenaga elektrik ditunjukkan di jadual di bawah.
62
EXERCISE / Latihan
Paper 2 – Section B & C / Kertas 2 – Bahagian B & C
1. Diagram below shows two types of plug for the electric kettle that can be connected to the
electric supply. Diagram (a) uses a two pin plug, while diagram (b) uses a three pin plug with
an earth wire.
Rajah di bawah menunjukkan dua jenis soket untuk cerek elektrik yang boleh disambung kepada bekalan
elektrik. Rajah (a) menggunakan soket dua pin, manakala Rajah (b) menggunakan soket tiga pin dengan
wayar bumi.
Two pin plug for the electric kettle Three pin plug for the electric kettle
Palam dua pin untuk cerek elektrik Palam tiga pin untuk cerek elektrik
Diagram (a) Diagram (b)
Rajah (a) Rajah (b)
a)
i) Explain where the earth wire is connected.
Jelaskan di mana wayar bumi disambungkan.
Earth wire is connected to the metal body of the electrical appliance
and to the ground.
Wayar bumi disambung kepada badan logam perkakas elektrik dan bumi.
ii) Based on diagram (a) and diagram (b), explain the disadvantages of using a two
pin plug as compared with a three pin plug with an earth wire.
Berdasarkan Rajah (a) dan Rajah (b), jelaskan keburukan menggunakan palam dua pin
berbandingkan dengan palam tiga pin dengan wayar bumi.
In two pin-plug appliances there is no earth wire. If the live wire
touches the metal body of the appliance, the metal body can becomes
the live wire. If a person touches the metal body the current will
pass through the body to the ground and the person may electrocute.
Soket dua pin tiada wayar bumi. Jika wayar hidup bersentuhan dengan
badan logam perkakas, badan logam akan menjadi wayar hidup. Jika
seorang menyentuh badan logam arus akan mengalir melalui badan ke bumi
dan orang itu akan tercedera.
Three pin-plugs have earth wire. With the earth wire, any current on
the metal body will flow to the ground through the earth wire. When
a person touches the metal body, the human body has higher
resistance than the wire, hence current will choose to flow through
the earth wire and the person will be save.
Soket tiga pin mempunyai wayar bumi. Dengan wayar bumi, sebarang arus
pada badan logam akan mengalir ke bumi melalui wayar bumi. Apabila
seorang menyentuh badan logam, badan manusia akan mempunyai rintangan
yang lebih tinggi berbanding wayar, oleh itu, arus akan memilih untuk
mengalir melalui wayar bumi dan orang itu akan terselamat.
63
b) Describe how efficiency of an electric kettle and a heating coil can be compared.
Jelaskan bagaimana kecekapan cerek elektrik dan gegelung pemanasan boleh dibandingkan.
A kettle and heating coil of the same power is used.
Cerek dan gegelung pemanasan dengan kuasa yang sama digunakan.
Same amount of water and initial temperature is used to be heated up
Jumlah air dan suhu awal yang sama digunakan untuk pemanasan.
The time taken to boil the water by the kettle and heating coil is
recorded.
Masa digunakan untuk mendidihkan air oleh cerek dan gegelung pemanas
direkodkan.
The appliance that needs a longer time to boil the water is less effective
because more energy loss.
Perkakas yang memerlukan masa yang lebih panjang untuk mendidihkan air
adalah kurang cekap kerana lebih banyak kehilangan tenaga.
64
c) Table below shows a list of electrical appliances that are used in a house.
Jadual di bawah menunjukkan senarai perkakas elektrik yang digunakan dalam sebuah rumah.
Electrical appliance Condition Time of usage
Perkakas elektrik Keadaan Masa penggunaan
Light Filament type 7:00 pm – 2:00 pm
Lampu Jenis filamen
65
2. Diagram below shows the essential components of an oven. The two heating elements are
connected in parallel to a 240 V mains socket. The resistance of each heating element is 100
Ω. The connecting wires to the heating element have a total resistance of 0.01 Ω.
Rajah di bawah menunjukkan komponen penting untuk sebuah ketuhar. Dua elemen pemanasan
disambung secara selari dengan soket utama 240 V. Rintangan untuk setiap elemen pemanasan adalah
100 Ω. Wayar penyambung ke elemen pemanasan mempunyai jumlah rintangan 0.01 Ω.
a)
i) Define the term resistance
Tentukan istilah rintangan
The resistance R is the ratio of the potential difference V to the
current I.
Rintangan R adalah nisbah beza keupayaan V dengan arus I.
ii) Explain why the heating element becomes much hotter than the wires
connecting to the main supply.
Jelaskan mengapa elemen pemanasan menjadi lebih panas berbanding wayar disambung
kepada bekalan utama.
The heating element has much higher resistance than the connecting
wires. A higher resistance wire produces more heat.
Elemen pemanasan mempunyai rintangan yang lebih tinggi berbanding
dengan wayar penyambung. Wayar dengan rintanagn tinggi menghasilkan
lebih banyak haba.
iii) Explain why the temperature of the heating element becomes steady soon after
the oven is switched on.
Jelaskan mengapa suhu elemen pemanasan menjadi stabil sebaik saja selepas ketuhar
dihidupkan.
The heating element is coiled wire which has a large surface area to
help dissipate heat to the surroundings.
Elemen pemanasan adalah gegelung wayar yang mempunyai luas permukaan
yang lebih besar untuk membantu melesapkan haba ke persekitaran.
When the heat produced per second by the heating element is equal
to the heat loss per second from the surface of the heating element,
the temperature of the heating element is constant.
Apabila haba dihasilkan per saat oleh elemen pemanasan adalah bersamaan
dengan kehilangan haba per saat dari permukaan elemen pemanasan, suhu
elemen pemanasan adalah malar.
66
b) You are supplied with 5 different resistance wires. The physical characteristic of the 5
wires P, Q, R, S and T are listed in table below.
Anda dibekalkan dengan 5 wayar dengan rintangan berbeza. Ciri fiikal 5 wayar P, Q, R, S dan T
disenaraikan di jadual di bawah.
i) Use the information in table above for the suitability of each of the physical
characteristic of the resistance wires to be used as the heating element of the
oven.
Menggunakan informasi di jadual di atas untuk kesesuaian untuk setiap ciri fizikal wayar
berintangan untuk digunakan sebagai elemen pemanasan ketuhar.
ii) Which resistance wire is the most suitable to be used as the heating element in
the oven and why?
Wayar berintangan yang mana paling sesuai untuk digunakan sebagai elemen pemanasan
dalam ketuhar dan kenapa?
The most suitable is S, as it has a low density, high melting point,
reasonably high resistively and is highly resistance to rust.
Paling susuai adalah S, ia mempunyai ketumpat rendah, takat lebur tinggi,
kerintangan tinggi yang munasabah dan kerintangan berkarat tinggi.
67
c) The electrical circuit diagram for the heating elements of the oven is as shown in
diagram below.
Rajah litar elektrik untuk elemen pemanasan ketuhar ditunjukkan di Rajah bawah.
i) Calculate the current flowing through the fuse when the oven is in use.
Hitung arus mengalir melalui fuis apabila ketuhar digunakan.
4.8 A
ii) Which of the fuses in table below is the most suitable to be used in circuit above.
Explain your answers.
Fuis yang mana di jadual bawah adalah paling sesuai untuk digunakan dalam litar di atas.
Jelaskan jawapan anda.
Fuses / Fuis 1A 3A 5A 10 A 13 A
The fuse used must have a current rating slightly higher than the
normal current in the circuit. 5 A is too near t0 4.8 A, 13 A is too
high. The most suitable is 10 A.
Fuis digunakan mesti mempunyai kadar arus lebih tinggi berbanding
dengan arus yang diperlukan dalam litar. 5 A terlalu dekat dengan 4.8 A,
13 A terlalu tinggi. Paling sesuai adalah 10 A.
68
3. A person wants to install new lamps in his house. Table below shows the characteristics of
four different kinds of lamps.
Seorang ingin memasang lampu yang baru dalam rumah dia. Jadual di bawah menunjukkan ciri-ciri
empat jenis lampu yang berbeza.
Explain the suitability of each characteristic table above and hence determine which lamp is
the most suitable to be used. Justify your answer.
Jelaskan kesesuaian setiap ciri jadual di atas dan oleh itu tentukan lampu yang mana paling sesuai untuk
digunakan. Jelaskan jawapan anda.
The most suitable lamp is compact fluorescent lamp. Although it has high purchase
price, compact fluorescent lamp has low power rating, higher energy efficiency and
long lifespan.
Lampu yang paling sesuai adalah lampu pendarfluor padat. Walaupun ia mempunyai harga
pembelian tinggi, lampu pendarfluor padat mempunyai kadar kuasa yang rendah, kecekapan
tenaga yang tinggi dan jangka hayat yang panjang.
69