Pada kesempatan ini pula, disampaikan terima kasih yang sebesar-besarnya kepada
seluruh anggota TIM Penyusun Spesifikasi Material Transmisi Utama (MTU) PT PLN
(Persero) yang telah bekerja keras dan meluangkan waktu, tenaga dan pikiran untuk
menyelesaikan Standardisasi Spesifikasi MTU ini. Semoga Allah SWT memberikan pahala
dan berkah-Nya kepada seluruh anggota Tim.
Wassalamualaikum Warahmatullahi Wabarakatuh
Direktur Utama
NUR PAMUDJI
------ BLANK PAGE ------
SK DIR NO. 216.K/DIR/2013 TENTANG STANDARDISASI
SPESIFIKASI MATERIAL TRANSMISI UTAMA (MTU) PT PLN
(PERSERO)
PT PLN (Persero)
DAFTAR ISI
1.7. Spesifikasi PMT 150 kV untuk lebih dari 1 (satu) Bay Kapasitor .......................................... 9
3.11. Spesifikasi CT 275 kV untuk Bay Penghantar dengan Proteksi Differensial ...................... 27
3.12. Spesifikasi CT 275 kV untuk Bay Penghantar dengan Proteksi Rele Jarak ....................... 28
3.15. Spesifikasi CT 500 kV untuk Bay Penghantar dengan Proteksi Differensial ...................... 31
3.16. Spesifikasi CT 500 kV untuk Bay Penghantar dengan Proteksi Rele Jarak ....................... 32
1.1. Pendahuluan........................................................................................................................ 57
2.1. Pendahuluan........................................................................................................................ 72
3.1. Pendahuluan........................................................................................................................ 83
4.1. Pendahuluan........................................................................................................................ 98
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 72,5
7 Rated frequency (Fr) Hz 50
8 - Rated normal current (Ir) A rms > 1250
9 - Rated short-time withstand current (I th) kA rms 25 or 31,5
10 - Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
- Phase to earth, between the phases and across the open breaker gap kV rms ≥ 140
Impulse withstand voltage (at 1,2/50 microsecond)
- Phase to earth, between the phases and across the open breaker gap kV peak ≥ 325
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 25 or 31,5
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV N.A
- circuit breaker open, grounded terminal µV N.A
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage S2
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 65
2. Opening time (trip initiation to contact separation) without current ms ≤ 50
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs ≥6
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
Value of closing resistor Ohm N/A
Insertion time of closing resistor ms N/A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record number of operation per set pcs 3
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per phase µ ohm < 100
38 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
39 Material of insulator Silicone Rubber/Porcelain
40 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 72,5
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms > 1250 or ≥ 2000
9 Rated short-time withstand current (I th) kA rms 25 or 31,5
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
- Phase to earth, between the phases and across the open breaker gap kV rms ≥ 140
Impulse withstand voltage (at 1,2/50 microsecond)
- Phase to earth, between the phases and across the open breaker gap kV peak ≥ 325
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(Not intended for rapid auto reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 25 or 31,5
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms N.A
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV N.A
- circuit breaker open, grounded terminal µV N.A
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage S2
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 1 ( one for three phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 65
2. Opening time (trip initiation to contact separation) without current ms ≤ 50
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Making time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs ≥6
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
Value of closing resistor Ohm N/A
Insertion time of closing resistor ms N/A
34 SF6 Pressure Indicator per set pcs 1
35 Counter to record number of operation per set pcs 1
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per phase µ ohm < 100
Number of switch operations between two inspections for changing the main-contacts
38
:
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
39 Material of insulator Silicone Rubber/Porcelain
40 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
7 Rated voltage (Ur) kV rms 170
8 Rated frequency (Fr) Hz 50
9 Rated normal current (Ir) A rms > 2000 or ≥ 3150
10 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
11 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
12 Rated duration of short circuit s ≥1
13 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open breaker gap kV rms ≥ 325
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open breaker gap kV peak ≥ 750
14 Minimum Creepage distance mm/kV 25 or 31
15 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
16 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20
17 Breaking current under out of phase condition kA rms ≥ 25 % x I th
18 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
19 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV to be mentioned
- circuit breaker open, grounded terminal µV to be mentioned
20 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
23 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
24 Number of interrupters in series per phase pcs 1
25 Number of tripping coils per phase pcs 2
26 Number of closing coils per phase pcs 1
27 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 ( one per phase)
28 Protection level of control cubicle min. IP54
29 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
30 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
31 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 40
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
32 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
34 Discrepancy device Yes
35 Antipumping device Yes
36 Method of controling voltage distribution between break unit N/A
37 Method of Closing control N/A
38 Value of closing resistor Ohm N/A
39 Insertion time of closing resistor ms N/A
40 SF6 Pressure Indicator per pole pcs 1
41 Counter to record number of operation per set pcs 3
42 Seismic acceleration constant consideration g 0,2 or 0,3
43 Leakage rate of SF6 gas per annum % ≤ 0.5
44 Contact resistance across main contacts per phase µ ohm < 80
Number of switch operations between two inspections for changing the main-contacts
45
:
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
47 Material of insulator Silicone Rubber/Porcelain
48 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of designation Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
7 Rated voltage (Ur) kV rms 170
8 Rated frequency (Fr) Hz 50
9 Rated normal current (Ir) A rms > 2000
10 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
11 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
12 Rated duration of short circuit s ≥1
13 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open breaker gap kV rms ≥ 325
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open breaker gap kV peak ≥ 750
14 Minimum Creepage distance mm/kV 25 or 31
15 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(Not intended for rapid auto reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
16 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20
17 Breaking current under out of phase condition kA rms ≥ 25 % x I th
18 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
19 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV to be mentioned
- circuit breaker open, grounded terminal µV to be mentioned
20 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 9
- Mechanical endurance M2
- Restrike performance C2
23 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
24 Number of interrupters in series per phase pcs 1
25 Number of tripping coils per phase pcs 2
26 Number of closing coils per phase pcs 1
27 Operating mechanism :
- Type motor spring
- Number of stored energy operation 1 ( one for three phase)
28 Protection level of control cubicle min. IP54
29 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
30 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
31 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 40
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
32 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
34 Discrepancy device N/A
35 Antipumping device Yes
36 Method of controling voltage distribution between break unit N/A
37 Method of Closing control N/A
38 Value of closing resistor Ohm N/A
39 Insertion time of closing resistor ms N/A
40 SF6 Pressure Indicator per set pcs 1
41 Counter to record number of operation per set pcs 1
42 Seismic acceleration constant consideration g 0,2 or 0,3
43 Leakage rate of SF6 gas per annum % ≤ 0.5
44 Contact resistance across main contacts per phase µ ohm < 80
45 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
47 Material of insulator Silicone Rubber/Porcelain
48 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of designation Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
7 Rated voltage (Ur) kV rms 170
8 Rated frequency (Fr) Hz 50
9 Rated normal current (Ir) A rms ≥ 1250 or ≥ 2000 or ≥ 2500 or ≥ 4000
10 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
11 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
12 Rated duration of short circuit s ≥1
13 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open breaker gap kV rms ≥ 325
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open breaker gap kV peak ≥ 750
14 Minimum Creepage distance mm/kV 25 or 31
15 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(Not intended for rapid auto reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
16 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20
17 Breaking current under out of phase condition kA rms ≥ 25 % x I th
18 Rated capacitive switching currents N/A
19 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV To be mentioned
- circuit breaker open, grounded terminal µV To be mentioned
20 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 9
- Mechanical endurance M2
- Restrike performance C2
23 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
24 Number of interrupters in series per phase pcs 1
25 Number of tripping coils per phase pcs 2
26 Number of closing coils per phase pcs 1
27 Operating mechanism :
- Type motor spring
- Number of stored energy operation 1 ( one for three phase)
28 Protection level of control cubicle min. IP54
29 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
30 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
31 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 40
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
32 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
34 Discrepancy device N/A
35 Antipumping device Yes
36 Method of controling voltage distribution between break unit N/A
37 Method of Closing control N/A
38 Value of closing resistor Ohm N/A
39 Insertion time of closing resistor ms N/A
40 SF6 Pressure Indicator per set pcs 1
41 Counter to record number of operation per set pcs 2
42 Seismic acceleration constant consideration g 0,2 or 0,3
43 Leakage rate of SF6 gas per annum % ≤ 0.5
44 Contact resistance across main contacts per phase µ ohm < 80
45 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
47 Material of insulator Silicone Rubber/Porcelain
48 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type Designation to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 170
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 1250
9 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open breaker gap kV rms ≥ 325
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open breaker gap kV peak ≥ 750
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(Not intended for rapid auto-reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 31,5 or 40 or 50
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV to be mentioned
- circuit breaker open, grounded terminal µV to be mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230/400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 40
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
Value of closing resistor Ohm N/A
Insertion time of closing resistor ms N/A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record number of operation per set pcs 3
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per phase µ ohm < 80
39 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current times to be mentioned
- with rated breaking current times to be mentioned
40 Material of insulator Silicone Rubber/Porcelain
41 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
1.7. Spesifikasi PMT 150 kV untuk lebih dari 1 (satu) Bay Kapasitor
PT PLN (Persero)
TECHNICAL PARTICULAR GUARANTEE
CIRCUIT BREAKER 150 kV
FOR BACK TO BACK CAPACITOR
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 170
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 1250
9 Rated short-time withstand current (I th) kA rms 31,5 or 40 or 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
Phase to earth, between the phases and across the open breaker gap kV rms ≥ 325
Impulse withstand voltage (at 1,2/50 microsecond)
Phase to earth, between the phases and across the open breaker gap kV peak ≥ 750
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(Not intended for rapid auto-reclosing) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms ≥ 31,5 or 40 or 50
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
- Rated inrush making current (I bi) kA peak ≥ 20
- Frequency of inrush current (f bi) Hz 4250
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV to be mentioned
- circuit breaker open, grounded terminal µV to be mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 °C ≤ 65
- Connection, bolted or equivalent in SF6 °C ≤ 75
- Terminal °C ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230/400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 50
2. Opening time (trip initiation to contact separation) without current ms ≤ 40
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N/A
33 Method of Closing control N/A
Value of closing resistor Ohm N/A
Insertion time of closing resistor ms N/A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record number of operation per set pcs 3
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per phase µ ohm < 80
39 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
40 Material of insulator Silicone Rubber or Porcelain
41 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 300
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 3150
9 Rated short-time withstand current (I th) kA rms 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
- Phase to earth, between the phases kV rms ≥ 395
Impulse withstand voltage (at 1,2/50 microsecond)
- Phase to earth, between the phases kV peak ≥ 1050
Switching withstand voltage (at 250/2500 microsecond)
- Phase to earth and and across the open breaker gap kV peak ≥ 850
- Between the phases kV peak ≥ 1275
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 50
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV to be mentioned
- circuit breaker open, grounded terminal µV to be mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 1
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 /400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 40
2. Opening time (trip initiation to contact separation) without current ms ≤ 30
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms N/A
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms N/A
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit N.A
33 Method of Closing control N.A
Value of closing resistor ohm N.A
Pre Insertion time of closing resistor ms N.A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record number of operation per set pcs 3
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per interrupters at rated current µ ohm < 80
39 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
40 Material of insulator Silicone Rubber/Porcelain
41 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 550
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 3150
9 Rated short-time withstand current (I th) kA rms 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
- Phase to earth, between the phases kV rms ≥ 620
Impulse withstand voltage (at 1,2/50 microsecond)
- Phase to earth, between the phases kV peak ≥ (1550 or 1800)
Switching withstand voltage (at 250/2500 microsecond)
- Phase to earth and and across the open breaker gap kV peak ≥ 1175
- Between the phases kV peak ≥ 1760
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 50
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV To be Mentioned
- circuit breaker open, grounded terminal µV To be Mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 2
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 40
2. Opening time (trip initiation to contact separation) without current ms ≤ 30
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms 2,5
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms 3
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit Capacitor
33 Method of Closing control closing resistor
Value of closing resistor Ohm to be mentioned
Pre Insertion time of closing resistor ms to be mentioned
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record the frequency of fault operation and normal operation pcs 3
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per interrupters at rated current µ ohm < 80
39 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
40 Material of insulator Silicone Rubber/Porcelain
41 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-100 and IEC 62271-1
2 Service condition Outdoor; Tropical area
3 Type of Circuit breaker Live Tank
4 Type of arc quenching medium SF6
5 Number of Phases phase 3
6 Rated voltage (Ur) kV rms 550
7 Rated frequency (Fr) Hz 50
8 Rated normal current (Ir) A rms ≥ 3150
9 Rated short-time withstand current (I th) kA rms 50
10 Rated peak withstand current (I p) kA peak ≥ 2,5 x I th
11 Rated duration of short circuit s ≥1
12 RATED INSULATION LEVEL :
Power frequency withstand voltage, dry for 1 minute
- Phase to earth, between the phases kV rms ≥ 620
Impulse withstand voltage (at 1,2/50 microsecond)
- Phase to earth, between the phases kV peak ≥ (1550 or 1800)
Switching withstand voltage (at 250/2500 microsecond)
- Phase to earth and and across the open breaker gap kV peak ≥ 1175
- Between the phases kV peak ≥ 1760
13 Minimum Creepage distance mm/kV 25 or 31
14 OPERATING SEQUENCE AND OPERATING DUTY
- Nominal Sequence
(rapid auto-reclosing/dead time) O - 0.3s - CO - 180s - CO
- Out of phase O - CO
15 Rated making and breaking current to Normal/Reclose
- Making current kA peak ≥ 2,5 x I th
- Breaking current (symmetrical) kA rms 50
- % dc component % dc > 20
16 Breaking current under out of phase condition kA rms ≥ 25 % x I th
17 Rated capacitive switching currents A rms refer to IEC 62271-100 table 9
18 Radio influence voltage level, measured at 1.1 Ur/√3 at 1 Mhz
- circuit closed to ground µV To be Mentioned
- circuit breaker open, grounded terminal µV To be Mentioned
19 Classes
- Electrical endurance E1
- Transient Recovery Voltage refer to IEC 62271-100 table 26
- Mechanical endurance M2
- Restrike performance C2
20 Temperature rise at :
- Contacts in SF6 K ≤ 65
- Connection, bolted or equivalent in SF6 K ≤ 75
- Terminal K ≤ 65
MECHANISM
Manufacture
Type
21 Number of interrupters in series per phase pcs 2
22 Number of tripping coils per phase pcs 2
23 Number of closing coils per phase pcs 1
24 Operating mechanism :
- Type motor spring
- Number of stored energy operation 3 (one per phase)
25 Protection level of control cubicle min. IP54
26 Supply voltage :
- Control voltage Volt DC 110
- Tripping and closing Coils Volt DC 110
- Motor voltage Volt AC 230 / 400
- Heater Volt AC 230
27 Tolerance range for auxiliary supply voltage
- tripping coil % 85 to 110
- closing coil % 85 to 110
- motor % 85 to 110
28 Mechanical performance
1. Total break time (trip initiation to final arc extinction) ms ≤ 40
2. Opening time (trip initiation to contact separation) without current ms ≤ 30
3. Time interval between opening of interrupters of first and last phase ms ≤4
4. Time interval between opening of interupters of one phase ms 2,5
5. Closing time without current ms ≤ 110
6. Time interval between closure of interrupters of the first and last pole ms ≤ 10
7. Time interval between closure of interrupters of one phase ms 3
8. Time from extinction of main arc to contact make ms ≤ 300
during auto-reclose duty
29 Number of auxiliary contacts (NO/NC) per pole pcs >8
OTHERS
30 Discrepancy device Yes
31 Antipumping device Yes
32 Method of controling voltage distribution between break unit Capacitor
33 Method of Closing control N.A
Value of closing resistor Ohm N.A
Pre Insertion time of closing resistor ms N.A
34 SF6 Pressure Indicator per pole pcs 1
35 Counter to record the frequency of fault operation and normal operation pcs 3
36 Seismic acceleration constant consideration g 0,2 or 0,3
37 Leakage rate of SF6 gas per annum % ≤ 0.5
38 Contact resistance across main contacts per interrupters at rated current µ ohm < 80
39 Number of switch operations between two inspections for changing the main-contacts :
- with rated continuous current to be mentioned
- with rated breaking current to be mentioned
40 Material of insulator Silicone Rubber/Porcelain
41 Minimum clearance in air :
- between phase mm to be mentioned (refer to IEC)
- phase to earth mm to be mentioned (refer to IEC)
- live conductor to ground level mm to be mentioned (refer to IEC)
- live insulator to ground level mm to be mentioned (refer to IEC)
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-102 and IEC 62271-1
2 Type of Designation Horizontal break or Vertical break
3 Service Condition - Outdoor; Tropical area
4 Rated Frequency (F r) Hz 50
5 Rated Voltage (U r) kVrms 72.5
6 Rated Normal Current (I r) A ≥ 1250 or ≥ 2000
7 Rated short time withstand current (I k) kA rms 25 or 31.5
8 Rated duration of short circuit s ≥1
9 Rated peak withstand current (I p) kA peak ≥ 2,5 x Ik
Rated static mechanical loading
10 a. Straight load N refer to IEC 62271-102 table 3
b.Cross load N
Rated values of bus transfer current swicthing capability of
disconnectors
11 0.8 x Ir or max. 1600 A
a.Rated Bus Transfer Current A
b.Rated Bus Transfer Voltage V rms 100
12 Rated values of mechanical endurance for disconnector class min M0 (1000 operating cyles)
13 Number of pole pole 3
14 Radio Interference Voltage µV N.A
INSULATION
Rated lightning impulse withstand voltage (BIL) - at 1,2/50
15
microsecond
- Phase to earth & between phase kVp ≥ 325
- Across Open Swicthing Device and/or isolating distance kVp ≥ 375
16 Power frequency withstand voltage (1 min) :
- phase to earth and between phases kVrms ≥140
- across open swicthing device and /or isolating distance kVrms ≥160
17 Creepage distances mm/kV 25 or 31
18 Minimum clearence in air :
- phase to phase mm 630
- to earth mm 630
GENERAL
19 Type of operating mechanism -
- Main Blade motor drive and manual
- Earthing Blade manual
20 Motor operating voltage (U a) VAC 230 / 400
- Tolerance range for auxilary supply voltage % 85 - 110 x Ua
Total time from initiation of opening operation to isolator in
21 s to be mentioned
fully open position
22 Motor Torque N to be mentioned
23 Contact Resistance µΩ ≤ 100
24 Degrees of Protection for Driving Mechanism Box (IP) IP min. 54
25 Material of enclosure (Mechanism Box) Alumunium / Stainless Steel
26 Poles arrangements: parallel
OTHERS
27 Seismic acceleration constant consideration g 0.2 or 0.3
28 Earthing Switch equipped with interlock system YES (line, pembangkit) or NO (trafo, kapasitor)
Measures to prevent building of bird's nests in the drive
29 YES
housing
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-102 and IEC 62271-1
2 Type of Designation Horizontal break or Vertical break
3 Service Condition - Outdoor; Tropical area
4 Rated Frequency (F r) Hz 50
5 Rated Voltage (U r) kVrms 170
6 Rated Normal Current (I r) A ≥ 2000 or ≥ 3150 or ≥ 4000
7 Rated short time withstand current (I k) kA rms 31.5 or 40 or 50
8 Rated duration of short circuit s ≥1
9 Rated peak withstand current (I p) kA peak ≥ 2,5 x Ik
Rated static mechanical loading
10 a. Straight load N refer to IEC 62271-102 table 3
b. Cross load N
Rated values of bus transfer current swicthing capability of
disconnectors
11
a. Rated Bus Transfer Current A 0.8 x Ir or max. 3200 A
b. Rated Bus Transfer Voltage V rms 100
12 Rated values of mechanical endurance for disconnector class min M0 (1000 operating cyles)
13 Number of pole pole 3
14 Radio Interference Voltage µV to be mentioned
INSULATION
Rated lightning impulse withstand voltage (BIL) - at 1,2/50
15
microsecond
- Phase to earth & between phase kVp ≥ 750
- Across Open Swicthing Device and/or isolating distance kVp ≥ 860
16 Power frequency withstand voltage (1 min) :
- phase to earth and between phases kVrms ≥ 325
- across open swicthing device and /or isolating distance kVrms ≥ 375
17 Creepage distances mm/kV 25 or 31
18 Minimum clearence in air :
- phase to phase mm 1500
- to earth mm 1500
GENERAL
19 Type of operating mechanism -
- Main Blade motor drive and manual
- Earthing Blade manual
20 Motor operating voltage (U a) VAC 230 / 400
- Tolerance range for auxilary supply voltage % 85 - 110 x Ua
Total time from initiation of opening operation to isolator in
21 s to be mentioned
fully open position
22 Motor Torque N to be mentioned
23 Contact Resistance µΩ ≤ 100
24 Degrees of Protection for Driving Mechanism Box (IP) IP min. 54
25 Material of enclosure (Mechanism Box) Alumunium / Stainless Steel
26 Poles arrangements: parallel
OTHERS
27 Seismic acceleration constant consideration g 0.2 or 0.3
YES (line, IBT, pembangkit) or NO (diameter, trafo,
28 Earthing Switch equipped with interlock system
kapasitor)
Measures to prevent building of bird's nests in the drive
29 YES
housing
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-102 and IEC 62271-1
2 Type of Designation Horizontal break or Vertical break
3 Service Condition - Outdoor; Tropical area
4 Rated Frequency (F r) Hz 50
5 Rated Voltage (U r) kVrms 300
6 Rated Normal Current (I r) A ≥ 3150
7 Rated short time withstand current (I k) kA rms 50
8 Rated duration of short circuit s ≥1
9 Rated peak withstand current (I p) kA peak ≥ 2,5 x Ik
Rated static mechanical loading
10 a. Straight load N refer to IEC 62271-102 table 3
b.Cross load N
Rated values of bus transfer current swicthing capability of
disconnectors
11
a.Rated Bus Transfer Current A 0.8 x I r or max. 2520 A
b.Rated Bus Transfer Voltage V rms 100
12 Rated values of mechanical endurance for disconnector class min M0 (1000 operating cyles)
13 Number of pole pole 3
14 Radio Interference Voltage µV to be mentioned
INSULATION
Rated lightning impulse withstand voltage (BIL) - at 1,2/50
15
microsecond
- Phase to earth & between phase kVp ≥ 1050
- Across Open Swicthing Device and/or isolating distance kVp ≥ 1050 (+170)
16 Rated switching impulse withstand voltage
- phase to earth and across open Switching device kVp ≥ 850
- between phases kVp ≥ 1275
- across isolating distance kVp ≥ 700 (+245)
17 Power frequency withstand voltage (1 min) :
- phase to earth and between phases kVrms ≥ 395
- across open swicthing device and /or isolating distance kVrms ≥ 435
18 Creepage distances mm/kV 25 or 31
19 Minimum clearence in air :
- phase to phase mm 2100
- to earth mm 1900
GENERAL
20 Type of operating mechanism -
- Main Blade motor drive and manual
- Earthing Blade manual
21 Motor operating voltage (U a) VAC 230 / 400
- Tolerance range for auxilary supply voltage % 85 - 110 x Ua
Total time from initiation of opening operation to isolator in
22 s to be mentioned
fully open position
23 Motor Torque N to be mentioned
24 Contact Resistance µΩ < 100
25 Degrees of Protection for Driving Mechanism Box (IP) IP min. 54
26 Material of enclosure (Mechanism Box) Alumunium / Stainless Steel
27 Poles arrangements: parallel
OTHERS
28 Seismic acceleration constant consideration g 0.2 or 0.3
29 Earthing Switch equipped with interlock system YES (line, IBT, pembangkit) or NO (diameter)
Measures to prevent building of bird's nests in the drive
30 YES
housing
Manufacturer to be mentioned
Type to be mentioned
1 Standard IEC 62271-102 and IEC 62271-1
Horizontal break or vertical break or Knee or
2 Type of Designation
Panthograph
3 Service Condition - Outdoor; Tropical area
4 Rated Frequency (F r) Hz 50
5 Rated Voltage (U r) kVrms 550
6 Rated Normal Current (I r) A ≥ 3150
7 Rated short time withstand current (I k) kA rms 50
8 Rated duration of short circuit s ≥1
9 Rated peak withstand current (I p) kA peak ≥ 2,5 x Ik
Rated static mechanical loading
10 a. Straight load N refer to IEC 62271-102 table 3
b. Cross load N
Rated values of bus transfer current Switching capability of
disconnectors
11
a. Rated Bus Transfer Current A 0.8 x Ir or max. 2520 A
b. Rated Bus Transfer Voltage V rms 100
12 Rated values of mechanical endurance for disconnector class min M0 (1000 operating cyles)
13 Number of pole pole 3
14 Radio Interface Voltage µV to be mentioned
INSULATION
Rated lightning impulse withstand voltage (BIL) - at 1,2 or
15
50 microsecond
- Phase to earth & between phase kVp ≥ 1550 or ≥ 1800
- Across Open Switching Device and or isolating distance kVp ≥ 1550 (+315) or ≥ 1800
16 Rated switching impulse withstand voltage
- phase to earth and across open Switching device kVp ≥ 1175
- between phases kVp ≥ 1760
- across isolating distance kVp ≥ 900 (+450)
17 Power frequency withstand voltage (1 min) :
- phase to earth and between phases kVrms ≥ 620 or ≥ 710
- Across Open Switching Device and or isolating distance kVrms ≥ 800 or ≥ 890
18 Creepage distances mm or kV 25 or 31
19 Minimum clearence in air :
- phase to phase mm 3100
- to earth mm 2900
GENERAL
20 Type of operating mechanism -
- Main Blade motor drive and manual
- Earthing Blade manual
21 Motor operating voltage (U a) VAC 230 / 400
- Tolerance range for auxilary supply voltage % 85 - 110 x Ua
Total time from initiation of opening operation to isolator in
22 s to be mentioned
fully open position
23 Motor Torque N to be mentioned
24 Contact Resistance at rated current µΩ ≤ 100
25 Degrees of Protection for Driving Mechanism Box (IP) IP min. 54
26 Material of enclosure (Mechanism Box) Alumunium / Stainless Steel
27 Poles arrangements: parallel
OTHERS
28 Seismic acceleration constant consideration g 0.2 or 0.3
YES (line, IBT, pembangkit) or NO (diameter,
29 Earthing Switch equipped with mechanical interlock system
Reaktor)
Measures to prevent building of bird's nests in the drive
30 YES
housing
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest voltage for equipment (Um) kV 72.5
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 25 or 31.5
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 300 or 1000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 2 or 3
17 Ratio
150-300/1 or 500-1000/1 or
Core no. 1 (main protection) A/A
150-300/5 or 500-1000/5
150-300/1 or 500-1000/1 or
Core no. 2 (back up protection) A/A
150-300/5 or 500-1000/5
Core no. 3 (busbar protection) A/A N.A
Core no. 4 (checkzone buspro high impedance) A/A N.A
150-300/1 or 500-1000/1 or
Core no. 5 (bidding meter) A/A
150-300/5 or 500-1000/5
18 Accuracy class :
Core no. 1 (main protection) - class PX
Core no. 2 (back up protection) - 5P20
Core no. 3 (busbar protection) - N.A
Core no. 4 (checkzone buspro high impedance) - N.A
Core no. 5 (bidding meter) - 0.2s
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (main protection) Ohm to be mentioned
Core no. 2 (back up protection) Ohm to be mentioned
Core no. 3 (busbar protection) Ohm N.A
Core no. 4 (checkzone buspro high impedance) Ohm N.A
Core no. 5 (bidding meter) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 (I fault trafo = 1979.5 A) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 3 (I fault = Ith) V N.A
Core no. 4 (I fault = Ith) V N.A
Core no. 5 VA ≥15 (for Isr = 1) or ≥ 35 (for Isr = 5)
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest voltage for equipment (Um) kV 72.5
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 25 or 31.5
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 1000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 2 or 3
17 Ratio
Core no. 1 (main protection) A/A 500-1000/1 or 500-1000/5
Core no. 2 (back up protection) A/A 500-1000/1 or 500-1000/5
Core no. 3 (busbar protection) A/A N.A
Core no. 4 (checkzone buspro high impedance) A/A N.A
Core no. 5 (bidding meter) A/A 500-1000/1 or 500-1000/5
18 Accuracy class :
Core no. 1 (main protection) - 5P20 (distance) or class PX (differential)
Core no. 2 (back up protection) - 5P20
Core no. 3 (busbar protection) - N.A
Core no. 4 (checkzone buspro high impedance) - N.A
Core no. 5 (bidding meter) - 0.2s
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (main protection) Ohm to be mentioned
Core no. 2 (back up protection) Ohm to be mentioned
Core no. 3 (busbar protection) Ohm N.A
Core no. 4 (checkzone buspro high impedance) Ohm N.A
Core no. 5 (bidding meter) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5) (distance)
Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead)) (line
(I fault = Ith) V
current differential)
Core no. 2 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 3 (I fault = Ith) V N.A
Core no. 4 (I fault = Ith) V N.A
Core no. 5 VA ≥ 15 (for Isr = 1) or ≥ 35 (for Isr = 5)
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest voltage for equipment (Um) kV 72.5
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 25 or 31.5
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 2000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 2
17 Ratio
Core no. 1 (OCR) A/A 1000-2000/1 or 1000-2000/5
Core no. 2 (busbar protection) A/A 1000-2000/1 or 1000-2000/5
18 Accuracy class :
Core no. 1 (OCR) - 5P20
Core no. 2 (busbar protection) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (OCR) Ohm to be mentioned
Core no. 2 (busbar protection) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - N.A
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest voltage for equipment (Um) kV 170
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 31.5 or 40 or 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 400
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 3 or 4 or 5
17 Ratio
Core no. 1 (main protection) A/A 50-100/1 or 150-300/1 or 50-100/5 or 150-300/5
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest voltage for equipment (Um) kV 170
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 31.5 or 40 or 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 500 or 2000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 3 or 4 or 5
17 Ratio
200-400/1 or 1000-2000/1 or
Core no. 1 (main protection) A/A
200-400/5 or 1000-2000/5
200-400/1 or 1000-2000/1 or
Core no. 2 (back up protection) A/A
200-400/5 or 1000-2000/5
Core no. 3 (busbar protection) A/A 2000-4000/1 or 2000-4000/5
Core no. 4 (checkzone buspro high impedance/centralized low impedance) A/A 2000-4000/1 or 2000-4000/5
200-400/1 or 1000-2000/1 or
Core no. 5 (bidding meter) A/A
200-400/5 or 1000-2000/5
18 Accuracy class :
Core no. 1 (main protection) - class PX
Core no. 2 (back up protection) - 5P20
Core no. 3 (busbar protection) - class PX
Core no. 4 (checkzone buspro high impedance) - class PX
Core no. 5 (bidding meter) - 0.2s
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (main protection) Ohm to be mentioned
Core no. 2 (back up protection) Ohm to be mentioned
Core no. 3 (busbar protection) Ohm to be mentioned
Core no. 4 (checkzone buspro high impedance) Ohm to be mentioned
Core no. 5 (bidding meter) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 (I fault trafo = 1847.5 A) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 3 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 VA ≥ 15 (for Isr = 1) or ≥ 35 (for Isr = 5)
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or vertical
34 yes
position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 170
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 31.5 or 40 or 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 1600 or 2000 or 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 3 or 4 or 5
17 Ratio
600-1200/1 or 1000-2000/1 or 2000-4000/1 or
Core no. 1 (main protection) A/A
600-1200/5 or 1000-2000/5 or 2000-4000/5
600-1200/1 or 1000-2000/1 or 2000-4000/1 or
Core no. 2 (back up protection) A/A
600-1200/5 or 1000-2000/5 or 2000-4000/5
Core no. 3 (busbar protection) A/A 2000-4000/1 or 2000-4000/5
Core no. 4 (checkzone buspro high impedance/centralized low A/A 2000-4000/1 or 2000-4000/5
600-1200/1 or 1000-2000/1 or 2000-4000/1 or
Core no. 5 (bidding meter) A/A
600-1200/5 or 1000-2000/5 or 2000-4000/5
18 Accuracy class :
Core no. 1 (main protection) - 5P20 (distance) or class PX (differential)
Core no. 2 (back up protection) - 5P20
Core no. 3 (busbar protection) - class PX
Core no. 4 (checkzone buspro high impedance) - class PX
Core no. 5 (bidding meter) - 0.2s
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (main protection) Ohm to be mentioned
Core no. 2 (back up protection) Ohm to be mentioned
Core no. 3 (busbar protection) Ohm to be mentioned
Core no. 4 (checkzone buspro high impedance) Ohm to be mentioned
Core no. 5 (bidding meter) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5) (distance)
Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead)) (line
(I fault = Ith) V
current differential)
Core no. 2 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 3 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 VA ≥ 15 (for Isr = 1) or ≥ 35 (for Isr = 5)
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 170
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 31.5 or 40 or 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 3 or 4
17 Ratio
Core no. 1 (busbar protection) A/A 2000-4000/1 or 2000-4000/5
Core no. 2 (CBF) A/A 2000-4000/1 or 2000-4000/5
Core no. 3 (CCP) A/A 2000-4000/1 or 2000-4000/5
Core no. 4 (meter) A/A 2000-4000/1 or 2000-4000/5
Accuracy class :
18 Core no. 1 (busbar protection) - class PX
Core no. 2 (CBF) - 5P20
Core no. 3 (CCP) - class PX
Core no. 4 (meter) 0.5
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (busbar protection) Ohm to be mentioned
Core no. 2 (CBF) Ohm to be mentioned
Core no. 3 (CCP) Ohm to be mentioned
Core no. 4 (meter) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 3 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 4 VA ≥ 15 (for Isr = 1) or ≥ 35 (for Isr = 5)
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance phase to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 170
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 31.5 or 40 or 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 2
17 Ratio
Core no. 1 (OCR) A/A 2000-4000/1 or 2000-4000/5
Core no. 2 (busbar protection) A/A 2000-4000/1 or 2000-4000/5
18 Accuracy class :
Core no. 1 (OCR) - 5P20
Core no. 2 (busbar protection) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (OCR) Ohm to be mentioned
Core no. 2 (busbar protection) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - N.A
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance phase to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 170
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 31.5 or 40 or 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2,5 x I th
9 Rated primary current (Ipr) A 300
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1 or 5
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 3
17 Ratio
Core no. 1 (OCR) A/A 150-300/1 or 150-300/5
Core no. 2 (busbar protection) A/A 2000-4000/1 or 2000-4000/5
Core no. 3 (busbar protection) A/A 2000-4000/1 or 2000-4000/5
18 Accuracy class :
Core no. 1 (OCR) - 5P20
Core no. 2 (busbar protection) - class PX
Core no. 3 (busbar protection) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (OCR) Ohm to be mentioned
Core no. 2 (busbar protection) Ohm to be mentioned
Core no. 3 (busbar protection) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A or Rlead = 1.16 ohm for Isr = 5 A)
Core no. 1 VA ≥ 20 (for Isr = 1) or ≥ 40 (for Isr = 5)
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance phase to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal or
34 yes
vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 300
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 40
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 1200
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (differential 1) A/A 600-1200/1
Core no. 2 (differential 2) A/A 600-1200/1
Core no. 3 (OCR) A/A 600-1200/1
Core no. 4 (CCP 1) A/A 2000-4000/1
Core no. 5 (CCP 2) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (differential 1) - class PX
Core no. 2 (differential 2) - class PX
Core no. 3 (OCR) - 5P20
Core no. 4 (CCP 1) - class PX
Core no. 5 (CCP 2) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (differential 1) Ohm to be mentioned
Core no. 2 (differential 2) Ohm to be mentioned
Core no. 3 (OCR) Ohm to be mentioned
Core no. 4 (CCP 1) Ohm to be mentioned
Core no. 5 (CCP 2) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (I fault IBT = 4619 A) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 (I fault IBT = 4619 A) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 VA ≥ 20
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal
34 yes
or vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 300
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 40
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 2000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (distance/line current differential 1) A/A 1000-2000/1
Core no. 2 (distance/line current differential 2) A/A 1000-2000/1
Core no. 3 (meter) A/A 1000-2000/1
Core no. 4 (CCP 1) A/A 2000-4000/1
Core no. 5 (CCP 2) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (line current differential 1) - class PX
Core no. 2 (line current differential 2) - class PX
Core no. 3 (meter) - 0,5
Core no. 4 (CCP 1) - class PX
Core no. 5 (CCP 2) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (distance/line current differential 1) Ohm to be mentioned
Core no. 2 (distance/line current differential 2) Ohm to be mentioned
Core no. 3 (meter) Ohm to be mentioned
Core no. 4 (CCP 1) Ohm to be mentioned
Core no. 5 (CCP 2) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 VA ≥ 15
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either
34 yes
horizontal or vertical position
3.12. Spesifikasi CT 275 kV untuk Bay Penghantar dengan Proteksi Rele Jarak
PT. PLN (Persero)
TECHNICAL PARTICULAR AND GUARANTEE
275 KV OUTDOOR CURRENT TRANSFORMER for TRANSMISSION LINE BAY WITH DISTANCE RELAY
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 300
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 40
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 2000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (distance) A/A 1000-2000/1
Core no. 2 (distance) A/A 1000-2000/1
Core no. 3 (meter) A/A 1000-2000/1
Core no. 4 (CCP 1) A/A 2000-4000/1
Core no. 5 (CCP 2) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (distance/line current differential 1) - class TPY
Core no. 2 (distance/line current differential 2) - class TPY
Core no. 3 (meter) - 0,5
Core no. 4 (CCP 1) - class PX
Core no. 5 (CCP 2) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (distance/line current differential 1) Ohm to be mentioned
Core no. 2 (distance/line current differential 2) Ohm to be mentioned
Core no. 3 (meter) Ohm to be mentioned
Core no. 4 (CCP 1) Ohm to be mentioned
Core no. 5 (CCP 2) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1
Core no. 2
Core no. 3 VA ≥ 15
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal
34 yes
or vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 300
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA ≥ 40
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (CCP 1A / buspro) A/A 2000-4000/1
Core no. 2 (CCP 2A / buspro) A/A 2000-4000/1
Core no. 3 (CBF) A/A 2000-4000/1
Core no. 4 (CCP 1B) A/A 2000-4000/1
Core no. 5 (CCP 2B) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (CCP 1A / buspro) - class PX
Core no. 2 (CCP 2A / buspro) - class PX
Core no. 3 (CBF) - 5P20
Core no. 4 (CCP 1B) - class PX
Core no. 5 (CCP 2B) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (CCP 1A / buspro) Ohm to be mentioned
Core no. 2 (CCP 2A / buspro) Ohm to be mentioned
Core no. 3 (CBF) Ohm to be mentioned
Core no. 4 (CCP 1B) Ohm to be mentioned
Core no. 5 (CCP 2B) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 VA ≥ 20
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - N.A
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect / Direct type
29 Oil compensation - Corrosion-proof metallic bellow / Gas Cushion
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either
34 yes
horizontal or vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 550
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 600
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (differential 1) A/A 600/1
Core no. 2 (differential 2) A/A 600/1
Core no. 3 (OCR) A/A 600/1
Core no. 4 (CCP 1) A/A 2000-4000/1
Core no. 5 (CCP 2) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (differential 1) - class PX
Core no. 2 (differential 2) - class PX
Core no. 3 (OCR) - 5P20
Core no. 4 (CCP 1) - class PX
Core no. 5 (CCP 2) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (differential 1) Ohm to be mentioned
Core no. 2 (differential 2) Ohm to be mentioned
Core no. 3 (OCR) Ohm to be mentioned
Core no. 4 (CCP 1) Ohm to be mentioned
Core no. 5 (CCP 2) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (I fault IBT = 4619 A) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 (I fault IBT = 4619 A) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 VA ≥ 20
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - N.A
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect type
29 Oil compensation - Corrosion-proof metallic bellow
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal
34 yes
or vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 550
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (line current differential 1) A/A 2000-4000/1
Core no. 2 (line current differential 2) A/A 2000-4000/1
Core no. 3 (meter) A/A 2000-4000/1
Core no. 4 (CCP 1) A/A 2000-4000/1
Core no. 5 (CCP 2) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (line current differential 1) - class PX
Core no. 2 (line current differential 2) - class PX
Core no. 3 (meter) - 0,5
Core no. 4 (CCP 1) - class PX
Core no. 5 (CCP 2) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (line current differential 1) Ohm to be mentioned
Core no. 2 (line current differential 2) Ohm to be mentioned
Core no. 3 (meter) Ohm to be mentioned
Core no. 4 (CCP 1) Ohm to be mentioned
Core no. 5 (CCP 2) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 VA ≥ 15
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect type
29 Oil compensation - Corrosion-proof metallic bellow
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either
34 yes
horizontal or vertical position
3.16. Spesifikasi CT 500 kV untuk Bay Penghantar dengan Proteksi Rele Jarak
PT. PLN (Persero)
TECHNICAL PARTICULAR AND GUARANTEE
500 KV OUTDOOR CURRENT TRANSFORMER for TRANSMISSION LINE BAY WITH DISTANCE RELAY
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 550
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (distance) A/A 2000-4000/1
Core no. 2 (distance) A/A 2000-4000/1
Core no. 3 (meter) A/A 2000-4000/1
Core no. 4 (CCP 1) A/A 2000-4000/1
Core no. 5 (CCP 2) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (distance) - class TPY
Core no. 2 (distance) - class TPY
Core no. 3 (meter) - 0,5
Core no. 4 (CCP 1) - class PX
Core no. 5 (CCP 2) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (distance) Ohm to be mentioned
Core no. 2 (distance) Ohm to be mentioned
Core no. 3 (meter) Ohm to be mentioned
Core no. 4 (CCP 1) Ohm to be mentioned
Core no. 5 (CCP 2) Ohm to be mentioned
20 Rated burden or Knee Point Voltage or Ual (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (Ual) V to be mentioned
Core no. 2 (Ual) V to be mentioned
Core no. 3 VA ≥ 15
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - ≤ FS 10
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect type
29 Oil compensation - Corrosion-proof metallic bellow
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal
34 yes
or vertical position
Manufacturer - to be mentioned
Type - to be mentioned
1 Standards - IEC 61869-1; IEC 61869-2
2 Type of designation - Top Core, Post Type, single phase
3 Service condition Outdoor; Tropical Area
4 Highest votage for equipment (Um) kV 550
5 Rated Frequency (Fr) Hz 50
6 Rated short time thermal current (Ith) kA 50
7 Rated duration of short circuit s ≥1
8 Dynamic withstand current (Idyn) kA ≥ 2.5 x Ith
9 Rated primary current (Ipr) A 4000
10 Rated continuous thermal current (Icth) A 1.2 x Ipr
11 Rated secondary current (Isr) A 1
12 Insulation Medium Paper oil insulated
GENERAL
16 Number of cores - 5
17 Ratio
Core no. 1 (CCP 1A / buspro) A/A 2000-4000/1
Core no. 2 (CCP 2A / buspro) A/A 2000-4000/1
Core no. 3 (CBF) A/A 2000-4000/1
Core no. 4 (CCP 1B) A/A 2000-4000/1
Core no. 5 (CCP 2B) A/A 2000-4000/1
18 Accuracy class :
Core no. 1 (CCP 1A / buspro) - class PX
Core no. 2 (CCP 2A / buspro) - class PX
Core no. 3 (CBF) - 5P20
Core no. 4 (CCP 1B) - class PX
Core no. 5 (CCP 2B) - class PX
19 Secondary resistance (Rct) for protection purpose at 75OC :
Core no. 1 (CCP 1A / buspro) Ohm to be mentioned
Core no. 2 (CCP 2A / buspro) Ohm to be mentioned
Core no. 3 (CBF) Ohm to be mentioned
Core no. 4 (CCP 1B) Ohm to be mentioned
Core no. 5 (CCP 2B) Ohm to be mentioned
20 Rated burden or Knee Point Voltage (on lowest ratio) :
(Rlead = 1.85 ohm for Isr = 1 A)
Core no. 1 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 2 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 3 VA ≥ 20
Core no. 4 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
Core no. 5 (I fault = Ith) V Vk ≥ 2 x (Ifault/Ratio x (Rct + Rlead))
21 Instrument security factor at nominal burden (measuring cores) - N.A
OTHERS
22 Insulator:
- Type Silicone Rubber or Porcelain
- Creepage distance to earth mm/kV 25 or 31
23 CT head housing material Aluminium alloy / Die cast / Mild steel
24 CT base housing material - Aluminium alloy / Die cast / Mild steel
25 Primary terminal - Flexible connection, suitable for plate
Made from corrosion resistant die cast
26 Secondary terminal box - alluminium, min IP54, removable, undrilled,
terminal flange with drainage
27 Earth terminal - one earth terminal
28 Oil level indicator - Indirect type
29 Oil compensation - Corrosion-proof metallic bellow
30 Method of ratio changing - Secondary
31 Capacitance Tap for Measurements of Voltage or Tan Delta Yes
32 Static withstand load class Load class II
33 Seismic condition (according to seismic map ) g ≥ 0.2 or 0.3
CT shall be designed for transport and storage in either horizontal
34 yes
or vertical position
Manufacturer to be mentioned
Type to be mentioned
1. Standard IEC 61869-5
2. Service Condition Outdoor, Tropical area
3. Nominal voltage kV 66 or 70
4. Highest Voltage for equipment (Um) kV 72,5
5. Rated frequency (Fr) Hz 50
6. Rated primary voltage (Upr) kV 66/√3 or 70/√3
7. Rated secondary voltage (Usr) V 100/√3 or 110/√3
GENERAL
10. Rated voltage factor and corresponding rated time, continuous 1,2
11. Rated voltage factor and corresponding rated time, 30 sec. 1,9
12. Dissipation factor of capacitor (tan δ) % ≤0.5
13. Accuracy class :
- for protection 3P
- for instrument and metering 0.2 or 0.5
14. Rated burden :
- for protection VA 30
- for instrument and metering VA 30
- total simultaneous burden VA 60
15. Rated capacitance pF 4000 up to 10000
16. Capacitance tolerance - 5 % to + 10 %
17. Ferro resonance :
- Duration of ferro resonance oscillation s ≤0.5
- Maximum instantaneous error after ferro resonance oscillation % ≤10
18. Suitable for use as coupling capacitor Yes
OTHERS :
19. Insulator material silicone rubber / porcelain
20. Oil compensation corrosion-proof metallic bellow with pressure relief
device
21. Mechanical characteristics :
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads :
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. electromechanical failing load to be mentioned
d) Max. operating load N to be mentioned
22. Oil level indicator Direct type
Made from corrosion resistant die cast alluminium,
23. Secondary terminal box IP54, removable, undrilled, terminal flange with
drainage
24. Earthed terminal one earth terminal
25. Sesmic Condition (Earthquake Factor) g ≥ 0.2 or 0.3
Manufacturer to be mentioned
Type to be mentioned
1. Standard IEC 61869-5
2. Service Condition Outdoor, Tropical area
3. Nominal voltage kV 150
4. Highest Voltage for equipment (Um) kV 170
5. Rated frequency (Fr) Hz 50
6. Rated primary voltage (Upr) kV 150/√3 or 154/√3
7. Rated secondary voltage (Usr) V 100/√3 or 110/√3
GENERAL
10. Rated voltage factor and corresponding rated time, continuous 1,2
11. Rated voltage factor and corresponding rated time, 30 sec. 1,5
12. Dissipation factor of capacitor (tan δ) % ≤0.5
13. Accuracy class :
- for protection 3P
- for instrument and metering 0.2 or 0.5
14. Rated burden :
- for protection VA 15
- for instrument and metering VA 15
- total simultaneous burden VA 30
15. Rated capacitance pF 4000 up to 10000
16. Capacitance tolerance - 5 % to + 10 %
17. Ferro resonance :
- Duration of ferro resonance oscillation s ≤0.5
- Maximum instantaneous error after ferro resonance oscillation % ≤10
18. Suitable for use as coupling capacitor Yes
OTHERS :
19. Insulator material silicone rubber / porcelain
corrosion-proof metallic bellow with pressure relief
20. Oil compensation
device
21. Mechanical characteristics : Suitable for mounting line trap minimum 250 kg
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads :
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. electromechanical failing load to be mentioned
d) Max. operating load N to be mentioned
22. Oil level indicator Direct type
Made from corrosion resistant die cast alluminium,
23. Secondary terminal box IP54, removable, undrilled, terminal flange with
drainage
24. Earthed terminal one earth terminal
25. Sesmic Condition (Earthquake Factor) g ≥ 0.2 or 0.3
Manufacturer to be mentioned
Type to be mentioned
1. Standard IEC 61869-5
2. Service Condition Outdoor, Tropical area
3. Nominal voltage kV 275
4. Highest Voltage for equipment (Um) kV 300
5. Rated frequency (Fr) Hz 50
6. Rated primary voltage (Upr) kV 275/√3
7. Rated secondary voltage (Usr) V 100/√3
GENERAL
10. Rated voltage factor and corresponding rated time, continuous 1,2
11. Rated voltage factor and corresponding rated time, 30 sec. 1,5
12. Dissipation factor of capacitor (tan δ) % ≤0.5
13. Accuracy class :
- for protection 3P
- for instrument and metering 0.2 or 0.5
14. Rated burden :
- for protection VA 15
- for instrument and metering VA 15
- total simultaneous burden VA 30
15. Rated capacitance pF 4000 up to 10000
16. Capacitance tolerance - 5 % to + 10 %
17. Ferro resonance :
- Duration of ferro resonance oscillation s ≤0.5
- Maximum instantaneous error after ferro resonance oscillation % ≤10
18. Suitable for use as coupling capacitor Yes
OTHERS :
19. Insulator material silicone rubber / porcelain
20. Oil compensation corrosion-proof metallic bellow
21. Mechanical characteristics : Suitable for mounting line trap minimum 250 kg
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads :
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. electromechanical failing load to be mentioned
d) Max. operating load N to be mentioned
22. Oil level indicator Direct type
Made from corrosion resistant die cast alluminium,
23. Secondary terminal box IP54, removable, undrilled, terminal flange with
drainage
24. Earthed terminal one earth terminal
25. Sesmic Condition (Earthquake Factor) g ≥ 0.2 or 0.3
Manufacturer to be mentioned
Type to be mentioned
1. Standard IEC 61869-5
2. Service Condition Outdoor, Tropical area
3. Nominal voltage kV 500
4. Highest Voltage for equipment (Um) kV 550
5. Rated frequency (Fr) Hz 50
6. Rated primary voltage (Upr) kV 500/√3
7. Rated secondary voltage (Usr) V 100/√3
GENERAL
10. Rated voltage factor and corresponding rated time, continuous 1,2
11. Rated voltage factor and corresponding rated time, 30 sec. 1,5
12. Dissipation factor of capacitor (tan δ) % ≤0.5
13. Accuracy class :
- for protection 3P
- for instrument and metering 0.2 or 0.5
14. Rated burden :
- for protection VA 15
- for instrument and metering VA 15
- total simultaneous burden VA 30
15. Rated capacitance pF 4000 up to 10000
16. Capacitance tolerance - 5 % to + 10 %
17. Ferro resonance :
- Duration of ferro resonance oscillation s ≤0.5
- Maximum instantaneous error after ferro resonance oscillation % ≤10
18. Suitable for use as coupling capacitor Yes
OTHERS :
19. Insulator material silicone rubber / porcelain
20. Oil compensation corrosion-proof metallic bellow
21. Mechanical characteristics :
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads :
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. electromechanical failing load to be mentioned
d) Max. operating load N to be mentioned
22. Oil level indicator Direct type
Made from corrosion resistant die cast alluminium,
23. Secondary terminal box IP54, removable, undrilled, terminal flange with
drainage
24. Earthed terminal one earth terminal
25. Sesmic Condition (Earthquake Factor) g ≥ 0.2 or 0.3
5.1. Spesifikasi LA 70 kV
PT PLN (PERSERO)
TECHNICAL PARTICULAR GUARANTEE
LIGHTNING ARRESTER 70 kV
Manufacturer to be mentioned
Type to be mentioned
IEC 60099-4;
1 Standard
IEC 60099-5
2 Service condition Outdoor, Tropical area
3 Type of Designation Post type, metal oxide, gapless
4 Type of housing Silicon Rubber / Porcelain
5 Frequency (Fr) Hz 50
6 Highest system voltage kV 72,5
7 System neutral connection non effective
8 Rated voltage (Ur) kV 72
9 Maximum Continuous Operating Voltage/MCOV (Uc) kV 57 up to 59
10 Class of Arrester 2
11 Rated nominal discharge current (8/20 us) (In) kA 10
12 Short circuit capability (for Arrester Housing) kA rms ≥ 40
13 Maximum Residual Voltage
- lightning impulse (wave 8/20 us) < 3.3 * Ur
- steep current impulse (front time 1 us) < 3.7 * Ur
- switching impulse (front time 30 us) < 2.6 * Ur
14 Electric strength of housing (at sea level)
- impulse withstand voltage (wave 1.2/50 us) kVp 325
- switching withstand voltage kVp NA
15 Creepage distance phase to earth according to IEC 60815 mm/Kv 25 or 31
GENERAL
16 Mechanical characteristics :
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. permissible static and dynamic pull N to be mentioned
17 Total height mm to be mentioned
18 Total weight kg to be mentioned
OTHER
provided with counter, time &
19 Counter arrester (required per phase) -
magnitude surge current recording
20 Leakage current monitor (required per phase) - analog
21 Maximum Leakage current mA to be mentioned
22 Seismic condition g 0.2 or 0.3
23 Corona Ring to be mentioned
24 Grading Ring to be mentioned
25 Low Voltage insulator base support Yes
Manufacturer to be mentioned
Type to be mentioned
IEC 60099-4;
1 Standard
IEC 60099-5
2 Service condition Outdoor, Tropical area
3 Type of Designation Post type, metal oxide, gapless
4 Type of housing Silicon Rubber / Porcelain
5 Rated Frequency (Fr) Hz 50
6 Highest system voltage kV 170
7 System neutral connection Solid (effective)
8 Rated voltage (Ur) kV 132 / 138
9 Maximum Continuous Operating Voltage/MCOV (Uc) kV 104 up to 112
10 Class of Arrester 3
11 Rated nominal discharge current (8/20 us) (In) kA 10
12 Short circuit capability (for Arrester Housing) kA rms ≥ 50
13 Maximum Residual Voltage
- lightning impulse (wave 8/20 us) < 3.3 * Ur
- steep current impulse (front time 1 us) < 3.7 * Ur
- switching impulse (30/60 us) < 2.6 * Ur
14 Electric strength of housing (at sea level)
- impulse withstand voltage (wave 1.2/50 us) kVp 750
- switching withstand voltage kVp NA
15 Creepage distance phase to earth according to IEC 60815 mm/Kv 25 or 31
GENERAL
16 Mechanical characteristics :
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. permissible static and dynamic pull N to be mentioned
17 Total height mm to be mentioned
18 Total weight kg to be mentioned
OTHER
provided with counter, time &
19 Counter arrester (required per phase) -
magnitude surge current recording
20 Leakage current monitor - analog
21 Maximum Leakage current mA to be mentioned
22 Seismic condition g 0.2 or 0.3
23 Corona Ring to be mentioned
24 Grading Ring to be mentioned
25 Low Voltage insulator base support Yes
Manufacturer to be mentioned
Type to be mentioned
IEC 60099-4;
1 Standard
IEC 60099-5
2 Service condition Outdoor, Tropical area
3 Type of Designation Post type, metal oxide, gapless
4 Type of housing Silicon Rubber / Porcelain
5 Frequency (Fr) Hz 50
6 Highest system voltage kV 300
7 System neutral connection Solid (effective)
8 Rated voltage (Ur) kV 240
9 Maximum Continuous Operating Voltage/MCOV (Uc) kV 190 up to 195
10 Class of Arrester min 3
11 Rated nominal discharge current (8/20 us) (In) kA min 10
12 Short circuit capability (for Arrester Housing) kA rms ≥ 50
13 Maximum Residual Voltage
- lightning impulse (wave 8/20 us) < 2.8 * Ur
- steep current impulse (front time 1 us) < 3.1 * Ur
- switching impulse (front time 30 us) < 2.3 * Ur
14 Electric strength of housing (at sea level)
- impulse withstand voltage (wave 1.2/50 us) kVp 1050
- switching withstand voltage kVp 850
15 Creepage distance phase to earth according to IEC 60815 mm/Kv 25 or 31
GENERAL
16 Mechanical characteristics :
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. permissible static and dynamic pull N to be mentioned
17 Total height mm to be mentioned
18 Total weight kg to be mentioned
OTHER
provided with counter, time &
19 Counter arrester (required per phase) -
magnitude surge current recording
20 Leakage current monitor - analog
21 Maximum Leakage current mA to be mentioned
22 Seismic condition g 0.2 or 0.3
23 Corona Ring Yes
24 Grading Ring Yes
25 Low Voltage insulator base support Yes
Manufacturer to be mentioned
Type to be mentioned
IEC 60099-4;
1 Standard
IEC 60099-5
2 Service condition Outdoor, Tropical area
3 Type of Designation Post type, metal oxide, gapless
4 Type of housing Silicon Rubber / Porcelain
5 Frequency (Fr) Hz 50
6 Highest system voltage kV 550
7 System neutral connection Solid (effective)
8 Rated voltage (Ur) kV 444
9 Maximum Continuous Operating Voltage/MCOV (Uc) kV 350 up to 360
10 Class of Arrester min 4
11 Rated nominal discharge current (8/20 us) (In) kA 20
12 Short circuit capability (for Arrester Housing) kA rms ≥ 50
13 Maximum Residual Voltage
- lightning impulse (wave 8/20 us) < 2.8 * Ur
- steep current impulse (front time 1 us) < 3.1 * Ur
- switching impulse (front time 30 us) < 2.3 * Ur
14 Electric strength of housing (at sea level)
- impulse withstand voltage (wave 1.2/50 us) kVp min 1550
- switching withstand voltage kVp 1175
15 Creepage distance phase to earth according to IEC 60815 mm/Kv 25 or 31
GENERAL
16 Mechanical characteristics :
a) Average mechanical breaking load N to be mentioned
b) Minimum failing loads
- tensile loads N to be mentioned
- torsional loads Nm to be mentioned
- cantilever loads N to be mentioned
- compressive loads N to be mentioned
c) Max. permissible static and dynamic pull N to be mentioned
17 Total height mm to be mentioned
18 Total weight kg to be mentioned
OTHER
provided with counter, time &
19 Counter arrester (required per phase) -
magnitude surge current recording
20 Leakage current monitor (required per phase) - analog
21 Maximum Leakage current mA to be mentioned
22 Seismic condition g 0.2 or 0.3
23 Corona Ring Yes
24 Grading Ring Yes
25 Low Voltage insulator base support Yes
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi busbar) Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- Incoming busbar A 2000
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. ≥1
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) - Minimum IP 4X
14 Insulation medium - air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar - 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Partitions and shutter of metalclad switchgear & controlgear Galvanized steel & earthed
21 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm refer to IAC complied
- other section mm refer to IAC complied
22 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
23 Heater with temperature control set To be mentioned (power and range temperature)
C. 20 KV CURRENT TRANSFORMER
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Standard IEC 60044-1
4 Type of design Post Type, single phase, indoor
5 Nominal voltage kV 20
6 Rated voltage (Ur) kV 24
7 Rated Frequency (Fr) Hz 50
8 Rated short time thermal current (Ith) kA 25
9 Rated duration of short circuit s ≥1
10 Dynamic withstand current (Idyn) kA 2,5 x Ith
D. 20 KV VOLTAGE TRANSFORMER
1 Manufacturer To be mentioned
2 Type To be mentioned
3 Standard IEC 60044-2
4 Type of design Indoor
5 Rated voltage (Ur) kV 24
6 Minimum Rated voltage factor 1,2 Continuous and 1,9 - 30 s
7 Rated Frequency Hz 50
8 Ratio, class, rated output :
a) for metering
- ratio V 20.000:√3 / 100:√3
- class - 0.2
- burden VA ≥ 30
b) for protection
- ratio V 20.000:√3 / 100:√3
- class - 3P
- burden VA 25
9 Rated lightning impulse withstand voltage (Up) kV 125
10 Power frequency withstand voltage (Ud) kV 50
E. PROTECTION RELAY
1 - Three-phase over current and Earth Fault (50, 50N, 51, 51N) Yes
2 - Under Frequncy relay (81U) Yes or No
3 - Under Voltage relay (27) Yes or No
G. ENERGY METER
1 Manufacturer To be mentioned
2 Type Digital kWh & kVARh meter, 3P 4W
3 Class of meter 0.2s
4 Rated input :
- current from 20 kV measurement A 5
- voltage from 20 kV VT V 100:√3
5 Quantity to be measured & recorded :
- sending Wh & Watt Yes
- receiving Wh & Watt Yes
- sending VARh & VAR Yes
- receiving VARh & VAR Yes
- sending VAh & VA Yes
- receiving VAh & VA Yes
6 Quantity to be measured :
- voltage kV Yes
- phase current A Yes
- power factor Yes
- frequency Hz Yes
7 Energy recording interval (programmable) minutes 1, 5, 10, 15, 20, 30 and 60
8 Tariff calculation mode functions Minimum 3 required
9 Rated operating conditions :
- rated auxiliary supply voltage Vdc 110 ± 10%
- temperature range °C 0 - 50
- humidity range %RH 20 - 90
10 Port communication comply to IEC 61850 Modem completed with optical wire port or RS485 or RJ45
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi busbar) Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- Outgoing busbar A ≥ 630
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. ≥1
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Partitions and shutter of metalclad switchgear & controlgear Galvanized steel & earthed
21 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm refer to IAC complied
- other section mm refer to IAC complied
22 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
23 Heater with temperature control set To be mentioned (power and range temperature)
C. 20 KV CURRENT TRANSFORMER
1 Manufacturer To be mentioned
2 Type To be mentioned
3 Standard IEC 60044-1
4 Type of design Post Type, single phase, indoor
5 Nominal voltage kV 20
6 Rated voltage (Ur) kV 24
7 Rated Frequency (Fr) Hz 50
8 Rated short time thermal current (Ith) kA 20 or 25
9 Rated duration of short circuit s ≥1
10 Dynamic withstand current (Idyn) kA 2,5 x Ith
11 Ratio, class, rated output :
a) for O/C and E/F protection :
- ratio A 100-200/5 or 300-600/5 or 400-800/5
- class - 5P20
- burden VA ≥ 15
b) for metering :
- ratio A 100-200/5 or 300-600/5 or 400-800/5
- class - 0,5
- Instrument security factor ≤ FS 10
- burden VA 10 or 15
12 Insulation temperature class (resin) minimum class E
E. PROTECTION RELAY
1 - Three-phase over current and Earth Fault (50, 50N, 51, 51N) Yes
2 - Directional relay (67/67N) Yes or No
3 - Auto-reclose (79) Yes or No
4 - Under voltage relay (27) Yes or No
G. ENERGY METER
1 Manufacturer To be mentioned
2 Type Digital kWh & kVARh meter, 3P 4W
3 Class of meter
- Incoming class 0.2s
- Outgoing class 0.5
4 Rated input :
- current from 20 kV measurement A 5
- voltage from 20 kV VT V 100:√3
5 Quantity to be measured & recorded :
- sending Wh & Watt Yes
- receiving Wh & Watt Yes
- sending VARh & VAR Yes
- receiving VARh & VAR Yes
- sending VAh & VA Yes
- receiving VAh & VA Yes
6 Quantity to be measured :
- voltage kV Yes
- phase current A Yes
- power factor Yes
- frequency Hz Yes
7 Energy recording interval (programmable) minutes 1, 5, 10, 15, 20, 30 and 60
8 Tariff calculation mode functions Minimum 3 required
9 Rated operating conditions :
- rated auxiliary supply voltage Vdc 110 ± 10%
- temperature range °C 0 - 50
- humidity range %RH 20 - 90
10 Port communication comply to IEC 61850 Modem completed with optical wire port or RS485 or RJ45
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current A ≥ 2000
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. ≥1
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Partitions and shutter of metalclad switchgear & controlgear Galvanized steel & earthed
21 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm refer to IAC complied
- other section mm refer to IAC complied
22 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
23 Heater with temperature control set To be mentioned (power and range temperature)
C. 20 KV CURRENT TRANSFORMER
1 Manufacturer To be mentioned
2 Type To be mentioned
3 Standard IEC 60044-1
4 Type of design Post Type, single phase, indoor
5 Nominal voltage kV 20
6 Rated voltage (Ur) kV 24
7 Rated Frequency (Fr) Hz 50
8 Rated short time thermal current (Ith) kA 25
9 Rated duration of short circuit s ≥1
10 Dynamic withstand current (Idyn) kA 2,5 x Ith
11 Ratio, class, rated output :
a) for O/C and E/F protection :
- ratio A 1000-2000/5
- class - 5P20
- burden VA ≥ 15
b) for metering :
- ratio A 1000-2000/5
- class - 0,5
- Instrument security factor ≤ FS 10
- burden VA 10 or 15
Insulation temperature class (resin) minimum class E
E. PROTECTION RELAY
1 Synchro check (25) Yes
2 Three-phase over current and Earth Fault (50, 50N, 51, 51N) Yes
3 Port communication comply to IEC 61850 Modem completed with optical wire port or RS485 or
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- section busbar A ≥ 2000
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. ≥1
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Partitions and shutter of metalclad switchgear & controlgear Galvanized steel & earthed
21 Minimum thickness of steel sheet :
- front panel for energy meter and others mounted mm refer to IAC complied
- other section mm refer to IAC complied
22 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
23 Heater with temperature control set To be mentioned (power and range temperature)
C. 20 KV CURRENT TRANSFORMER
1 Manufacturer To be mentioned
2 Type To be mentioned
3 Standard IEC 60044-1
4 Type of design Post Type, single phase, indoor
5 Nominal voltage kV 20
6 Rated voltage (Ur) kV 24
7 Rated Frequency (Fr) Hz 50
8 Rated short time thermal current (Ith) kA 25
9 Rated duration of short circuit s 3
10 Dynamic withstand current (Idyn) kA 2,5 x Ith
E. PROTECTION RELAY
1 Three-phase over current and Earth Fault (50, 50N, 51, 51N) Yes
2 Port communication comply to IEC 61850 Modem completed with optical wire port or RS485 or
G. ENERGY METER
1 Manufacturer To be mentioned
2 Type Digital kWh & kVARh meter, 3P 4W
3 Class of meter 0.5
4 Rated input :
- current from 20 kV measurement A 5
- voltage from 20 kV VT V 100:√3
5 Quantity to be measured & recorded :
- sending Wh & Watt Yes
- receiving Wh & Watt Yes
- sending VARh & VAR Yes
- receiving VARh & VAR Yes
- sending Vah & VA Yes
- receiving Vah & VA Yes
6 Quantity to be measured :
- voltage kV Yes
- phase current A Yes
- power factor Yes
- frequency Hz Yes
7 Energy recording interval (programmable) minutes 1, 5, 10, 15, 20, 30 and 60
8 Tariff calculation mode functions Minimum 3 required
9 Rated operating conditions :
- rated auxiliary supply voltage Vdc 110 ± 10%
- temperature range °C 0 - 50
- humidity range %RH 20 - 90
10 Port communication comply to IEC 61850 Modem completed with optical wire port or RS485 or
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi busbar) Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- Riser busbar A ≥ 2000
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. ≥1
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm refer to IAC complied
- other section mm refer to IAC complied
21 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
22 Heater with temperature control set To be mentioned (power and range temperature)
PT PLN (Persero)
TECHNICAL PARTICULAR AND GUARANTEE
PHBTM BUS RISER BUSBAR
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi busbar) Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- Riser busbar A ≥ 2000
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. ≥1
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm refer to IAC complied
- other section mm refer to IAC complied
21 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
22 Heater with temperature control set To be mentioned (power and range temperature)
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi busbar) Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- VT/LA busbar A ≥ 630
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. 3
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
20 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm 2.5
- other section mm refer to IAC complied
21 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
22 Heater with temperature control set to be mentioned (power and range temperature)
B. 20 KV VOLTAGE TRANSFORMER
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Standard IEC 60044-2
4 Type of design Indoor
5 Rated voltage (Ur) kV 24
6 Minimum Rated voltage factor 1,2 Continuous and 1,9 - 30 s
7 Rated Frequency Hz 50
8 Ratio, class, rated output :
a) for metering
- ratio V 20.000:√3 / 100:√3
- class - 0.2
- burden VA ≥ 30
b) for protection
- ratio V 20.000:√3 / 100:√3
- class - 3P
- burden VA 25
9 Rated lightning impulse withstand voltage (Up) kV 125
10 Power frequency withstand voltage (Ud) kV 50
C. DISCONNECTOR SWITCH
1 Manufacturer To be mentioned
2 Type To be mentioned
4 Standard IEC 60265
6 Rated voltage kV 24
7 Rated nominal current A ≥ 630
8 Rated lightning impuls withstand voltage kV 125
9 Rated short-time withstand current (Ik) kA 25
10 Making capacity kA 2,5 x Ik
11 Rated frequency Hz 50
12 Interrupting medium SF6 or Vacuum
13 Mechanism type manual
14 Mechanical endurance M2 (5.000 times)
D. PROTECTION RELAY
1 Under Frequncy relay (81U) Yes or No
2 Under Voltage relay (27) Yes or No
3 Port communication comply to IEC 61850 Modem completed with optical wire port or RS485 or RJ45
F. FUSE
F.1 FUSE-BASE
1 Manufacturer To be mentioned
2 Rated voltage kV 24
3 Rated current A ≥ 100
F.2 FUSE-LINK
1 Manufacturer To be mentioned
2 Type of designation Indoor, limiting current
3 Rated voltage kV 24
4 Rated current A 6
A. 20 KV SWITCHGEAR
1 Manufacturer to be mentioned
2 Type to be mentioned
3 Type of designation (tempat pemasangan dan konfigurasi busbar) Indoor metal clad and single busbar
4 Standard IEC 62271-200
5 Rated voltage (Ur) kV 24
6 Rated lightning impuls withstand voltage (Up) kV 125
7 Rated power frequency withstand voltage (Ud) kV 50
8 Rated frequency Hz 50
9 Rated normal current
- Main busbar A ≥ 2000
- local service busbar A ≥ 630
10 Rated short-time withstand current ( I k ) kA 25
11 Rated duration of short circuit sec. 3
12 Rated peak withstand current ( I p ) kA 2,5 x I k
13 Degrees of protection (IP) Minimum IP 4X
14 Insulation medium air
15 Busbar system :
Material Copper with heatshrink
Main busbar at upper side mm2 to be mentioned
Terminal for Busbar Cable at lower side mm2 to be mentioned
Earthing busbar mm2 to be mentioned
16 Number of phase busbar 3
17 Auxiliary supply
Rated supply voltage of closing and opening devices Vdc 110
Rated supply voltage of control circuit (aux, relay) Vdc 110
Rated supply voltage of auxiliary (heater) Vac 230
18 Loss of service continuity catagory (LSC) LSC2B
19 Internal arc classification (IAC) kA-1sec AFLR 25
21 Minimum thickness of steel sheet :
- front panel for relay, energy meter and others mounted mm 2.5
- other section mm refer to IAC complied
22 Dimension of switchgear cubicle :
- width mm to be mentioned
- depth mm to be mentioned
- height mm to be mentioned
23 Heater with temperature control set To be mentioned (power and range temperature)
B. DISCONNECTOR SWITCH
1 Manufacturer To be mentioned
2 Type To be mentioned
4 Standard IEC 60265
6 Rated voltage kV 24
7 Rated nominal current A ≥ 630
8 Rated lightning impuls withstand voltage kV 125
9 Rated short-time withstand current (Ik) kA 25
10 Making capacity kA 2,5 x Ik
11 Rated frequency Hz 50
12 Interrupting medium SF6 or Vacuum
13 Mechanism type manual
14 Mechanical endurance M2 (5.000 times)
C. FUSE
C.1 FUSE-BASE
1 Manufacturer To be mentioned
2 Rated voltage kV 24
3 Rated current A ≥ 100
C.2 FUSE-LINK
1 Manufacturer To be mentioned
2 Type of designation Indoor, limiting current
3 Rated voltage kV 24
4 Rated current A 40 or 50 or 63
Bab 1
1.2.1 Manufacturer
Merupakan nama pabrikan dan tempat dimana peralatan diproduksi.
Contoh : ABB Jerman, SIEMENS China, ALSTOM India
1.2.2 Type
Merupakan kode tipe peralatan yang diproduksi dimana kode type peralatan
tersebut harus sesuai dengan type test peralatan yang dilampirkan. Selain itu kode
type ini akan memudahkan identifikasi peralatan, baik untuk kepentingan
operasional dan pemeliharaan.
Contoh : GL 330, LTB 170 dll.
1.2.3 Standards
Merupakan acuan baku yang digunakan sebagai referensi dalam
penentuan/perhitungan nilai setiap variabel.
Standar umum untuk MTU yang digunakan adalah IEC 62271-1:2007-10 ED.1
Standar khusus untuk peralatan Pemutus tenaga yang digunakan adalah IEC
62271-100:2008-4 ED.02
1.2.4 Service condition
Menjelaskan tentang lokasi pemasangan dan kondisi lingkungan, dalam hal ini
dipersyaratkan mampu digunakan :
Outdoor, digunakan di luar ruangan, harus tahan terhadap sinar matahari (UV), air
hujan, angin dan debu.
Tropical Area, memiliki ketahanan terhadap iklim tropis (sesuai dengan iklim
Indonesia).
Contoh Pemilihan:
Nilai Ir ditentukan oleh user sesuai dengan kebutuhan sistem dimana peralatan
pemutus tenaga akan dipasang dan kesesuian dengan mass product manufacturer
yang tersedia di pasaran.
Pilihan yang ada adalah 1250A, 1600A, 2000A, 2500A, 3150A, dan 4000A.
Contoh cara menentukan nilai Ir
Misalnya dibutuhkan PMT untuk trafo 150/20 kV kapasitas 60 MVA, maka
Kebutuhan arus nominal = 60.000 kVA / (150 kV * √3) = 231 A
Kapasitas trafo 150 kV yang terpasang dan digunakan di PLN mempunyai
keragaman kapasitas antara lain 10 MVA, 20 MVA, 30 MVA, 50 MVA, 60 MVA,
100 MVA, 250 MVA dan 500 MVA dapat disederhanakan dengan pertimbangan
kemudahan penyediaan material dalam operasional penyediaan tenaga listrik dan
ketersediaan pasar secara masal sehingga mendapatkan material optimal serta
efisien maka dipilih rating arus untuk trafo 150 kV dengan berbagai kapasitas trafo
sebesar 2000 Ampere.
Contoh lain jika dibutuhkan PMT untuk penghantar dengan konduktor 2 x 435 mm2,
di mana kemampuan hantar arus nominalnya adalah 2 x 780 A maka dipilih PMT
dengan rating arus sebesar 1600 A.
1.2.11 Rated Short Time Withstand Current (Ith)
Kemampuan peralatan dialiri arus rms (simetris) maksimum selama durasi tertentu
tanpa mengalami kerusakan.
Nilai dipilih berdasarkan hasil studi tingkat arus hubung singkat di Gardu Induk di
mana peralatan tersebut akan dipasang serta dengan mempertimbangkan
perkembangan sistem. Dalam hal ini dipilih 25 kA dan 31,5 kA untuk 70 kV,
31.5kA, 40 kA, 50 kA untuk 150 kV, 50 kA untuk 275 kV dan 500 kV.
Pemilihan kemampuan maksimum arus hubung singkat dalam speksifikasi tertulis
25 kA or 31,5 kA or 40 kA or 50 kA, kata “or” menunjukkan angka tersebut hanya
dapat dipilih salah satu sesuai dengan kebutuhan sistem.
1.2.12 Rated Peak Withstand Current (Ip)
Kemampuan peralatan dialiri arus asimetris maksimum yang berhubungan dengan
komponen dc dari sistem. Dalam hal ini, nilai Ip ditetapkan berdasarkan IEC
62271-1, besarannya adalah 2.5 x kemampuan arus hubung singkat simetris (Ith)
Contoh : untuk Ith = 40 kA, maka Ip = 2,5 x 40 kA = 100 kA
1.2.13 Rated Duration of Short Circuit
Durasi waktu dimana peralatan tersebut harus dapat bertahan dengan arus hubung
singkat simetris (Ith), dimana waktu tersebut mengakomodir kecepatan dan
kemampuan peralatan sistem pengaman dalam meng-isolir gangguan tanpa
merusak peralatan (durasi Ith > fault time clearance)
1.2.14 Rated Insulation Level; Power Frequency Withstand Voltage, Dry for 1
minute
Menyatakan tegangan tegangan lebih maksimal akibat power frequency yang
dapat diterima sistem isolasi pemutus tenaga dalam periode 1 menit tanpa
menyebabkan kerusakan.
Contoh : 325 kVrms untuk sistem 150 kV.
1.2.15 Rated Insulation Level; Impulse Withstand Voltage
Menyatakan tentang ketahanan peralatan terhadap tegangan lebih akibat impuls
petir dengan bentuk gelombang 1,2/50 µs, dalam hal ini peralatan disesuaikan
dengan tegangan sistem dimana peralatan tersebut terpasang.
Contoh : 750 kVpeak untuk sistem 150 kV.
1.2.16 Minimum Creepage Distance
Menyatakan jarak rambat minimal aliran listrik pada permukaan isolator sehingga
ketahanan isolasi tetap terjaga. Pemilihan jarak rambat minimal disesuaikan
dengan rating tegangan dan tingkat polusi dimana peralatan tersebut dipasang.
Jarak rambat isolasi dapat dipilih berdasarkan tingkat polusi di daerah di mana
peralatan GI tersebut terpasang, menurut IEC standar tingkat polusi dapat dibagi
menjadi medium, heavy dan very heavy, dalam hal ini dengan pertimbangan
Indonesia berapa di daerah dengan tingkat kelembaban dan polusi tinggi maka,
dipilih heavy (25 mm/kV) dan very heavy (31 mm/kV). Khusus untuk isolator jenis
very heavy (31 mm/kV) digunakan di GI dengan tingkat polusi berat seperti GI
dekat pantai, dekat pabrik kimia, atau dekat pabrik semen. Sedangkan untuk GI
yang tidak berada di lokasi tersebut dapat menggunakan isolator jenis heavy (25
mm/kV).
Pemilihan jarak rambat minimal dalam speksifikasi tertulis 25 mm/kV or 31 mm/kV,
kata “or” menunjukkan angka tersebut hanya dapat dipilih salah satu sesuai
dengan kebutuhan sistem.
Contoh : untuk peralatan dengan rated voltage (Ur) 170 kV yang terpasang pada
daerah dengan tingkat polusi tinggi, maka minimum jarak rambat isolasi yang
diperlukan adalah 4250 mm sehingga minimum creepage distance dipilih 25
mm/kV.
1.2.17 Operating Sequence and Operating Duty
Menyatakan kemampuan peralatan Pemutus Tenaga (PMT) untuk melakukan
siklus pembukaan dan penutupan kontak PMT baik secara single phasa maupun 3
phasa dalam periode tertentu tanpa mengalami kerusakan.
Contoh : O – 300 ms – CO – 180 s – CO
reclose dalam 300 ms setelah PMT terbuka, hal ini mempertimbangkan dead time
SPAR (single pole auto reclose) adalah 800 ms
- Out of phase
Adalah siklus kerja PMT yang dipengaruhi oleh kemampuan penyimpanan energi
penggerak PMT. Siklus ini dipilih O – CO (open – close open) dimana PMT
diharapkan setelah terbuka/trip dapat masuk kembali (reclose) dan dapat trip
kembali jika gangguan permanen.
1.2.18 Rated Making and Breaking Current to Normal/Reclose
- Making current
Adalah kemampuan PMT untuk dialiri arus saat PMT menutup/close dimana timbul
arus puncak yang dapat mencapai 2,5 x Ith.
- %dc Component
Adalah kemampuan PMT memutus aliran listrik di mana terdapat dc komponen
pada sistem, persyaratan ini diperlukan karena PMT harus dapat memutus aliran
listrik pada saat masih terdapat komponen dc di sistem. Untuk menghitung %dc,
dapat menggunakan rumus IEC 62271-100 tahun 2008 hal 137.
%dc = 100 x e-(Top+Tr)/ζ
dengan penghantar 500 kV karena pada sistem 500 kV dikenal dengan ada arus
pengisian saluran (Line Charging) akibat efek kapasitansi saluran. Dalam hal ini
digunakan closing resistor.
- Value Of Closing Resistor
Menyatakan besarnya nilai closing resistor yang digunakan
- Pre Insertion Time Of Closing Resistor
Menyatakan waktu closing resistor bekerja membagi tegangan.
1.2.37 SF6 Pressure Indicator per Pole
Menyatakan PMT harus menyediakan indikator tekanan SF6 pada setiap Pole
1.2.38 Counter To Record The Frequency Of Fault Operation And Normal
Operation
Menyatakan jumlah counter untuk mencatat setiap operasi PMT baik beroperasi
saat gangguan atau saat manuver normal.
1.2.39 Seismic Acceleration Constant Consideration
Menyatakan tingkat ketahanan PMT terhadap gempa. Berdasarkan peta
kerawanan gempa maka dipertimbangkan tingkat kerawanan gempa di lokasi
gardu induk, maka dipilih 0.2 g untuk kondisi dengan kekuatan gempa hingga 6
SR, dan 0.3 g untuk daerah dengan kekuatan gempa hingga 9 SR.
Pemilihan tingkat ketahanan PMT terhadap gempa dalam speksifikasi tertulis 0.2 g
or 0.3 g, kata “or” menunjukkan angka tersebut hanya dapat dipilih salah satu
sesuai dengan kebutuhan sistem.
1.2.40 Leakage Rate of SF6 Gas per Annum
Menyatakan tingkat kebocoran SF6 per annum yang dijinkan untuk setiap intrupter
1.2.41 Contact Resistance Across Main Contacts Per Interrupters At Rated Current
Menyatakan besarnya tahanan main kontak yang dijinkan, hal ini penting karena
tahanan kontak yang tinggi dapat menimbulkan panas yang akan merubah sifat
SF6 yang dalam waktu lama akan menyebabkan kerusakan pada kontak dan nilai
ini sangat berguna untuk pemeliharaan dan assement PMT
1.2.42 Number Of Switch Operations Between Two Inspections For Changing The
Main-Contacts :
Menyatakan jumlah operasi PMT yang ijinkan antara satu pemeriksaan dengan
pemeriksaan berikutnya yang berguna untuk menentukan waktu overhaul PMT
untuk mengganti kontak utama.
- With Rated Continuous Current
Jumlah kerja PMT saat manuver dengan arus normal
- With Rated Breaking Current
Jumlah kerja PMT saat memutus arus gangguan
Tabel 1.1
Klasifikasi PMT Berdasarkan Letak PMT untuk Penghantar, Diameter, Kapasitor dan Kopel
PMT
PMT
PMT
PMT
PMT PMT
PMT PMT
Tabel 1.1
Klasifikasi PMT Berdasarkan Letak PMT untuk Penghantar, Diameter, Kapasitor dan Kopel
(lanjutan)
No Klasifikasi PMT Letak PMT
PMT
PMT
PMT
PMT
9 Bay Kapasitor 70 kV
dan 150 kV
PMT
PMT
PMT
PMT
Tabel 3.2
Daftar Simbol
No Peralatan Simbol
7 LA (Lightning Arrester)
8 Kapasitor
9 Busbar
11 Pembangkit
Bab 2
2.2.1. Manufacturer
Merupakan nama pabrikan dan tempat dimana peralatan diproduksi.
Contoh : ABB Jerman, SIEMENS China, ALSTOM India, GAE Indonesia, dll.
2.2.2. Type
Merupakan kode tipe peralatan yang diproduksi dimana kode type peralatan
tersebut harus sesuai dengan type test peralatan yang dilampirkan. Selain itu kode
type ini akan memudahkan identifikasi peralatan, baik untuk kepentingan
operasional dan pemeliharaan.
Dalam speksifikasi tertulis to be mentioned, kata “to be mentioned” menunjukkan
Pabrikan wajib menuliskan tipe peralatan yang ditawarkan.
Contoh : SDAT 170.
2.2.3. Standards
Merupakan acuan baku yang digunakan sebagai referensi dalam
penentuan/perhitungan nilai setiap variabel.
Standar yang digunakan dalam menyusun spesifikasi ini adalah IEC standar
dengan pertimbangan:
Standar digunakan secara luas di dunia
Peralatan di yang terpasang di lingkungan PT PLN (Persero) mayoritas
menggunakan IEC standar
Sesuai dengan kebutuhan O&M di lingkungan PT PLN (Persero)
Standar khusus untuk peralatan Pemisah yang digunakan adalah IEC 62271-102
Standard umum untuk switchgear adalah IEC 60071-1
Penulisan dalam spesifikasi 230/400 Vac, mempunyai arti bahwa motor pengerak
dapat digerakkan menggunakan sumber ac satu fasa 220 Vac atau tiga fasa 380
Vac. Tanda “/” menyatakan bahwa pabrikan dapat menyediakan motor pengerak
dengan spesifikasi satu fasa atau tiga fasa atau kedua-duanya.
2.2.23. Total Time From Initiation Of Opening Operation To Isolator In Fully Open
Position
Menjelaskan berapa waktu yang dibutuhkan mulai dari kontak diinisiasi hingga tuas
PMS terbuka penuh, hal ini diperlukan untuk mengetahui kapan peralatan yang
terhubung ke PMS tersebut sudah aman. Dalam hal ini masing-masing diminta
untuk mengisi batasan yang dibutuhkan.
Motor Torque
Menjelaskan kebutuhan torsi motor yang diperlukan untuk menggerakkan tuas
pisau pemisah
gardu induk, maka dipilih 0.2 g untuk kondisi dengan kekuatan gempa hingga 6
SR, dan 0.3 g untuk daerah dengan kekuatan gempa hingga 9 SR.
Pemilihan tingkat ketahanan PMT terhadap gempa dalam speksifikasi tertulis 0.2 g
or 0.3 g, kata “or” menunjukkan angka tersebut hanya dapat dipilih salah satu
sesuai dengan kebutuhan sistem.
Tabel 2.1
Klasifikasi PMT Berdasarkan Letak PMS Untuk Penghantar, Diameter, Kapasitor dan Kopel
Tabel 2.1
Klasifikasi PMT Berdasarkan Letak PMS Untuk Penghantar, Diameter, Kapasitor dan Kopel
(lanjutan)
Klasifikasi PMS Letak PMS
No
Bay Kapasitor 70 kV
6
dan 150 kV yaitu PMS
yang yang berfungsi
memisahkan kapasitor
dengan PMT bay PMS
kapasitor.
PMS KOPEL
Tabel 2.2
Daftar Simbol
No Peralatan Simbol
7 LA (Lightning Arrester)
8 Kapasitor
9 Busbar
11 Pembangkit
Bab 3
3.2.1. Manufacturer
Merupakan nama pabrikan dan tempat di mana peralatan diproduksi.
Contoh : ABB Sweden, TRENCH Italy, ALSTOM France, dan lain-lain.
3.2.2. Type
Merupakan kode tipe peralatan yang diproduksi di mana kode type peralatan
tersebut harus sesuai dengan type test peralatan yang dilampirkan. Selain itu kode
type ini akan memudahkan identifikasi peralatan, baik untuk kepentingan
operasional dan pemeliharaan.
Dalam speksifikasi tertulis to be mentioned, kata “to be mentioned” menunjukkan
Pabrikan wajib menuliskan tipe peralatan yang ditawarkan.
Contoh : OSKF 170
3.2.3. Standards
Merupakan acuan baku yang digunakan sebagai referensi dalam
penentuan/perhitungan nilai setiap variabel.
Standar yang digunakan dalam menyusun spesifikasi ini adalah IEC standar
dengan pertimbangan:
• standar digunakan secara luas di dunia
• peralatan yang terpasang di lingkungan PT PLN (Persero) mayoritas
menggunakan IEC standar
• sesuai dengan kebutuhan O&M di lingkungan PT PLN (Persero)
Standar khusus untuk peralatan trafo arus yang digunakan adalah IEC 61869-1;
IEC 61869-2
pada GI 70 dan 150 kV yang lama, khusus untuk GI 150 kV di Jawa Timur yang
dibangun dengan pinjaman dari Jepang.
1. Keperluan proteksi,
2. Keperluan metering.
Untuk kondisi tertentu yang memerlukan checkzone busbar protection maka dapat
ditambahkan 1 core lagi.
Pemilihan jumlah core dalam speksifikasi CT tertulis 3 or 4 or 5, kata “or”
menunjukkan angka tersebut hanya dapat dipilih salah satu sesuai dengan
kebutuhan sistem. 3 core dipilih jika sistem hanya membutuhkan CT untuk proteksi
utama, proteksi cadangan dan meter transaksi. 4 core dipilih jika sistem proteksi GI
dilengkapi dengan busbar protection tipe low impedance sedang 5 core jika
menggunakan busbar protection tipe high impedance atau centralized low
impedance.
Contoh :
T/R bay double busbar untuk KTT, dipilih 4 core
- Core ke-1 untuk main protection
- Core ke-2 untuk backup protection
- Core ke-3 untuk busbar protection
- Core ke-4 untuk bidding meter
3.2.19. Ratio
Menyatakan perbandingan arus primer dan sekunder dari trafo arus, dipilih dengan
pertimbangan :
1. Arus nominal dari peralatan yang diproteksi/diukur,
2. Daerah kerja sesuai dengan kurva hysteresis,
3. Kelas akurasi,
4. Pengembangan sistem,
5. Manajemen material dan kemudahan penggantian.
Tabel 3.1 Penentuan Ratio Primer CT Bay Trafo 150/70 kV, 70/20 kV
Tegangan Trafo
No. In Trafo (A) Ratio Primer Dipilih – Ipr (A)
Trafo (kV) (MVA)
1 70/20 10 82.5
2 70/20 15 123.7 150 - 300
3 70/20 30 247.4
4 150/70 60 494.9
500 - 1000
5 150/70 100 824.8
Tegangan Trafo
No. In Trafo (A) Ratio Primer Dipilih – Ipr (A)
Trafo (kV) (MVA)
1 150/20 10 38
50 - 100
2 150/20 20 77
3 150/20 30 115
4 150/20 50 192 150 - 300
5 150/20 60 231
Tabel 3.3 Penentuan Ratio Primer CT Bay Trafo IBT 150/70 kV, 275/150 kV, 500/150
kV
Tegangan Trafo
No. I Trafo (A) Ratio Primer Dipilih – Ipr (A)
Trafo (kV) (MVA)
1 150/70 30 115
2 150/70 60 231 200 - 400
3 150/70 100 385
4 275/150 250 962
1000 - 2000
5 500/150 500 1925
Tipe Konduktor
No. I (A) Ratio Primer Dipilih – Ipr (A)
(mm2)
lebih besar dari yang dipersyaratkan. Kata”(distance)” berarti jenis rele proteksi
yang digunakan.
Arus Nominal CT : 1 A
Rlead : 3.08 Ohm/km
Jarak CT dg Relai/Meter : 0.3 km
Burden Relai : 5 VA
Burden Meter : 10 VA
Burden yang diperlukan : 15.924 VA
Burden+safety factor : 19.11 VA
Burden CT : 20 VA
Vk adalah batas tegangan jenuh CT, merupakan parameter untuk kelas PX,
dihitung pada ratio terendah, nilainya berbanding lurus dengan Rct, dan dihitung
sesuai :
Di mana:
Ifault: arus hubung singkat maksimum yang melewati CT
Ratio: perbandingan antara arus primer dan sekunder CT
Rct : Resistansi dari belitan CT
Rlead : Resistansi kabel kontrol dari CT hingga ke rele proteksi di panel rele
Pemilihan tingkat akurasi untuk CT dalam speksifikasi CT tertulis untuk main
protection adalah 5P20 (distance) or class PX (differential), kata “or” menunjukkan
angka tersebut hanya dapat dipilih salah satu sesuai dengan rele proteksi yang
digunakan
Contoh :
Bay trafo 150/20 kV 60 MVA yang tersambung dengan busbar yang memiliki
tingkat arus hubung singkat (SCL) sistem sebesar 40 kA, memerlukan CT class PX
dengan ratio 150 - 300 / 1, Rct = 3 ohm, R lead = 1.85 ohm maka :
3.2.24. Insulator
Isolasi antara tegangan primer ke struktur/tanah.
Pemilihan isolator dilakukan dengan mempertimbangkan :
1. Kemampuan isolasi
2. Kemampuan mekanik
3. Tingkat polusi
4. Teknologi bahan isolator
Type
Sehingga dipilih untuk bahan isolator menggunakan porcelain atau silicone rubber.
(Pemilihan silicone rubber, material harus tahan terhadap sinar ultra violet).
Pemilihan jenis material isolasi luar CT dalam speksifikasi tertulis Silicone
Rubber/Porcelain, kata “Silicone Rubber/Porcelain” menunjukkan material tersebut
dapat dipilih salah satu oleh pabrikan untuk ditawarkan sesuai dengan teknologi
yang telah dikuasai oleh pabrikan.
Creepage distance
Creepage distance adalah jarak isolasi CT dari fasa ke tanah, dipilih berdasarkan
tingkat polusi di lokasi. Untuk daerah dengan tingkat polusi ringan sampai berat
dipilih 25 mm/kV, sedangkan untuk daerah dengan tingkat polusi sangat berat
dipilih 31 mm/kV.
Pemilihan jarak rambat minimal dalam speksifikasi tertulis 25 mm/kV or 31 mm/kV,
kata “or” menunjukkan angka tersebut hanya dapat dipilih salah satu sesuai
dengan kebutuhan sistem.
Contoh :
Untuk daerah GI dekat dengan pabrik semen dipilih creepage distance 31 mm/kV.
1. Penggunaan.
2. Tegangan sistem di mana CT akan terpasang
3. Letak peralatan yang akan diproteksi atau diukur.
Berdasarkan pertimbangan tersebut kalsifikasi dapat dibagi menjadi:
3.3.7. Klasifikasi CT Berdasarkan Letak Peralatan Yang Akan Diproteksi atau Diukur
CT dapat diklasifikasi juga berdasarkan letak peralatan yang diukur atau diproteksi,
klasifikasi berdasarkan letak ini sangat berpengaruh karena harus
mempertimbangkan kemampuan CT dilewati arus nominal, jangan sampai CT
menjadi bottle-neck jika dipilih nominal CT lebih kecil dari nominal peralatan yang
diukur atau diproteksi. Untuk itu CT dapat dapat diklasifikasikan menjadi: CT untuk
Trafo, Kopel, IBT, Kapasitor, Diameter dan penghantar, pada Tabel 3.6 dan 3.7
akan diperlihatkan penempatan CT sesuai letaknya.
Tabel 3.6
Klasifikasi CT Berdasarkan Letak CT Untuk Trafo
No Klasifikasi CT Letak CT
CT CT
CT CT
3 Bay IBT 150/70 kV 150 kV 70 kV
CT CT
4 Bay IBT 275/150 kV 275 kV 150 kV
CT CT
CT CT
Tabel 3.7
Klasifikasi CT Berdasarkan Letak CT Untuk Penghantar, Diameter, Kapasitor dan Kopel
No Klasifikasi CT Letak CT
1 Bay Penghantar 70 kV
dan 150 kV
CT
CT
CT
CT
Tabel 3.8
Daftar Simbol
No Peralatan Simbol
7 LA (Lightning Arrester)
8 Kapasitor
9 Busbar
11 Pembangkit
Bab 4
Capacitor Voltage Transformer (CVT) adalah salah satu jenis Trafo Tegangan yang
bersifat kapasitif terdiri dari rangkaian seri 2 (dua) kapasitor atau lebih yang
berfungsi sebagai pembagi tegangan dari tegangan tinggi ke tegangan rendah pada
primer, selanjutnya tegangan pada satu kapasitor ditransformasikan mengunakan
trafo tegangan yang lebih rendah agar diperoleh tegangan sekunder
4.2.1. Manufacturer
Merupakan nama pabrikan dan tempat di mana peralatan diproduksi.
Contoh : ABB Sweden, TRENCH Italy, ALSTOM India, dan lain-lain.
4.2.2. Type
Merupakan kode tipe peralatan yang diproduksi di mana kode type peralatan
tersebut harus sesuai dengan type test peralatan yang dilampirkan. Selain itu kode
type ini akan memudahkan identifikasi peralatan, baik untuk kepentingan
operasional dan pemeliharaan.
Contoh : OTCF 170 SR.
4.2.3. Standards
Merupakan acuan baku yang digunakan sebagai referensi dalam
penentuan/perhitungan nilai setiap variabel.
Standar yang digunakan dalam menyusun spesifikasi ini adalah IEC standar
dengan pertimbangan:
• standar digunakan secara luas di dunia
• peralatan yang terpasang di lingkungan PT PLN (Persero) mayoritas
menggunakan IEC standar
• sesuai dengan kebutuhan O&M di lingkungan PT PLN (Persero)
Standar khusus untuk peralatan CVT yang digunakan adalah IEC 61869-5
Nominal frekuensi sistem di mana peralatan trafo arus akan beroperasi. Dalam hal
ini adalah nominal frekuensi sistem PLN, yaitu 50 Hz.
dengan kekuatan gempa hingga 9 SR. Pemilihan tingkat ketahanan PMT terhadap
gempa dalam speksifikasi tertulis 0.2 g or 0.3 g, kata “or” menunjukkan angka
tersebut hanya dapat dipilih salah satu sesuai dengan kebutuhan system
4.3. Pemilihan CVT (Capacitor Voltage Transformer)
Pemilihan CVT dapat dilakukan dengan pertimbangan kebutuhan yang disesuaikan
dengan kegunaannya, yaitu:
1. Penggunaan.
2. Tegangan sistem di mana CVT akan terpasang
3. Letak peralatan yang akan diproteksi atau diukur.
Berdasarkan pertimbangan tersebut kalsifikasi dapat dibagi menjadi:
4.3.5. Klasifikasi CVT Berdasarkan Letak Peralatan Yang Akan Diproteksi atau
Diukur
CVT dapat diklasifikasi juga berdasarkan letak peralatan yang diukur atau
diproteksi. Untuk itu CVT dapat dapat diklasifikasikan menjadi: CVT untuk
SUTT/SUTET, Kopel, IBT dan Kapasitor, pada Tabel 4.1 dan 4.2 akan
diperlihatkan penempatan CVT sesuai letaknya.
Tabel 4.1
Klasifikasi CVT Berdasarkan Letak CVT untuk
SUTT, SUTET, Pembangkit, IBT, Kapasitor dan Kopel
CVT
CVT CVT
CVT CVT
CVT
CVT
CVT
Tabel 4.2
Daftar Simbol
No Peralatan Simbol
7 LA (Lightning Arrester)
8 Kapasitor
9 Busbar
11 Pembangkit
Bab 5
5.2.1. Manufacturer
Merupakan nama pabrikan dan tempat dimana peralatan diproduksi.
Contoh : ABB Jerman, SIEMENS China, ALSTOM India, GAE Indonesia dll.
5.2.2. Type
Merupakan kode tipe peralatan yang diproduksi dimana kode type peralatan
tersebut harus sesuai dengan type test peralatan yang dilampirkan. Selain itu kode
type ini akan memudahkan identifikasi peralatan, baik untuk kepentingan
operasional dan pemeliharaan.
Contoh : PEXLIM P-X, 3EL2 132 - 3PM31 - 4xxx
5.2.3. Standards
Merupakan acuan baku yang digunakan sebagai referensi dalam
penentuan/perhitungan nilai setiap variabel.
Standar yang digunakan dalam menyusun spesifikasi ini adalah IEC standar
dengan pertimbangan:
standar digunakan secara luas di dunia
peralatan di yang terpasang di lingkungan PT PLN (Persero) mayoritas
menggunakan IEC standar
bekerja, bekerja, bekerja…. II-107
PT PLN (Persero)
Di mana :
Nilai konstanta 1.05 adalah faktor safety yang dipilih sebagai pertimbangan nilai
tegangan yang mampu ditahan oleh arrester dalam periode waktu terbatas (IEC
60099-5).
Us = tegangan nominal sistem (kV)
Nilai yang diperoleh dipilih sesuai tabel IEC 60099-4 Ed-2.2 yang telah ditentukan.
Table 5.1
Step of rated voltages
kV r.m.s. kV r.m.s.
3 - 30 1
30 - 54 3
54 - 96 6
96 - 288 12
288 - 396 18
396 - 756 24
NOTE Other values of rated voltage may be accepted, provided they are
multiples of 6.
Sumber: IEC 60099-4 Ed 2.2
Contoh : untuk tegangan nominal sistem (Us) = 150 kV dari hasil perhitungan
diperoleh Ur = 128 kV, dari tabel 2 IEC 60099-4 dipilih Ur = 132 kV.
Di mana:
Ur = rated voltage arrester
Contoh : untuk rated voltage (Ur) = 132 kV maka MCOV arrester adalah 106 kV
diterima, sehingga Pabrikan akan mengisi suatu nilai yang masih dalam range
tersebut. .
a
In some countries it is customary to classify arresters as follows:
Contoh:
Tegangan nominal sistem 500 kV dan SUTET 500 kV melewati daerah kerapatan
petir (Ng = 16 sambaran per km2 per tahun) dan besar arus maksimum rata-rata
20 kA maka dipilih class 4.
Pemilihan nominal discharge current, dapat ditentukan dengan mengetahui berapa
maksimum arus petir yang mengenai langsung ke konduktor akibat kegagalan
bekerja, bekerja, bekerja…. II-111
PT PLN (Persero)
30 – 132 2,6 – 3,1 2,3 – 2,8 2,0 – 2,3 2,6 – 3,7 2,3 – 3,3 2,0 – 2,6
144 – 342 2,6 – 3,1 2,3 – 2,8 2,0 – 2,3 2,6 – 3,7 2,3 – 3,3 2,0 – 2,6
360 - 756 2,6 – 3,1 2,3 – 2,8 2,0 – 2,3 2,6 – 3,1 2,3 – 2,8 2,0 – 2,3
NOTE . The table gives the range of maximum residual voltage normally available. Low value refer
normally to arresters with high line discharge class and vice versa.
Sumber: IEC 60099-4 Ed-2.2
Bab 6
5.4.1. Manufacturer
Merupakan nama pabrikan yang memproduksi PHBTM 20 kV.
Contoh : PLN-Indonesia
5.4.2. Type
Merupakan kode tipe PHBTM dari pabrikan yang memproduksi peralatan tersebut.
Kode ini akan memudahkan identifikasi peralatan, baik yang akan dipasang
maupun yang sudah terpasang.
Contoh : PGC-24
5.4.3. Standards
Merupakan acuan baku yang digunakan sebagai referensi dalam
penentuan/perhitungan nilai setiap variabel.
Standar PHBTM yang digunakan adalah IEC 62271-200.
a b c d.1
d.2 e f g
CATATAN
Gambar 6-1. merupakan diagram satu garis secara umum, detail komponen yang
digunakan (relay, kWh meter, watt meter Dll.) disesuaikan kebutuhan di Gardu
Induk.
a. Panel Incoming
Digunakan sebagai penerima energi listrik dari trafo tenaga GI sisi 20 kV dan
disalurkan ke busbar utama.
b. Panel Outgoing
5.4.24. Ratio CT
Pemilihan rasio berdasarkan batas kesalahan CT dengan mempertimbangkan
besar arus sekunder 5 A dan besar arus primer yang akan mengalir.
Ratio : Rasio CT
Rct : Resistans CT [ohm]
Rlead : Total resistans beban CT [ohm]
Untuk proteksi arus lebih dipilih kelas proteksi 5P20 artinya pada arus gangguan
sebesar 20 kali arus primer dengan beban sesuai burden pengenal maka batas
kesalahan komposit sebesar 5%.
5.4.29. Burden VT
Pemilihan burden diperhitungkan sesuai jumlah VA alat ukur dan penghantar yang
digunakan, nilai burden pada batas kesalahan (akurasi) ditentukan dengan kondisi:
25% sampai 100% burden pengenal
80% sampai 120% tegangan pengenal
DAFTAR ISTILAH
No Istilah Penjelasan
1 GI Gardu Induk
2 Trafo tenaga Power Transformer, adalah alat yang transformasikan tegangan dari
tegangan tinggi ke tegangan rendah atau sebaliknya, yang termasuk
trafo tenaga adalah trafo 150/20 kV dan 70/20 kV
4 PMT Pemutus tenaga atau Circuit Breaker (CB), alat ini berfungsi untuk
memutus aliran arus dengan memisahkan kontak dalam ruang
tertutup, sebagai pemadam busur listrik dan isolasi dalam ruang
tertutup digunakan SF6, udara bertekanan atau Vacum
5 PMS Pemisah atau Disconnecting Switch (DS), alat ini berfungsi untuk
mengisolasi aliran listrik dengan cara memisahkan kontak, sebagai
pemadam busur listrik digunakan udara biasa
DAFTAR ISTILAH
(lanjutan)
No Istilah Penjelasan
13 Live Tank Intrupter berada dalam selungkup isolasi baik porcelain maupun
polymer yang berdiri dan berhubungan langsung terhadap bagian
yang bertegangan
14 Intrupter Selubung tempat kontak antara dua bagian yang bertegangan atau
salah satunya bertegangan berada yang berisolasi vacuum atau SF6
17 Creepage Jarak aman suatu peralatan di mana arus listrik yang merambat pada
Distance isolasi tidak menimbulkan hubung singkat.
18 SPAR Single Pole Auto Reclose, Reclose kembali satu fasa saat terjadi
PMT trip satu fasa.
19 Tripping Coil Coil yang bekerja mengerakkan mekanik PMT untuk trip.
20 Closing Coil Coil yang bekerja mengerakkan mekanik PMT untuk closed.
27 Top Core Istilah ini ada di CT yang berarti inti belitan dari CT berada di bagian
atas konstruksi CT
DAFTAR ISTILAH
(lanjutan)
No Istilah Penjelasan
28 Bottom Core Istilah ini ada di CT yang berarti inti belitan dari CT berada di bagian
bawah konstruksi CT
30 Low Impedance Istilah di proteksi busbar menggunakan rele differential yang bekerja
membandingkan arus masuk dan arus keluar sama (hukum kirchoff)
dengan prinsip impedansi kecil.
31 High Impedance Istilah di proteksi busbar menggunakan rele differential yang bekerja
membandingkan arus masuk dan arus keluar sama (hukum kirchoff)
dengan prinsip impedansi besar.
32 Auxiliary Current Trafo arus bantu, yang bekerja mentraformasikan arus sekunder
Transformer yang perbandingannya tidak besar, misalnya trafo 5 A ke1 A
33 OCR Over Current Relay, rele arus lebih yang bekerja jika terjadi hubung
singkat maka arus hubung singkatnya melebihi setting rele maka rele
akan bekerja pada waktuy yang sudah ditentukan.
34 GFR Ground Fault Relay, rele arus lebih tanah yang bekerja jika terjadi
hubung singkat tanah
35 Distance Relay Adalah rele proteksi yang bekerja dengan membanding impedansi
gangguan yang terbaca oleh rele dengan setting impedansi di rele.
36 Shielding Failure Kegagalan perlindungan dari kawat tanah (ground wire), sehingga
petir langsung menyampar ke konduktor)
DAFTAR ISTILAH
(lanjutan)
No Istilah Penjelasan
44 VT/LA busbar PHBTM yang berisi trafo tegangan dan lightning arrester tegangan
menengah