LX-1170
®
SEDM997003
Memperhatikan
□ Seluruh hak cipta. Tidak ada bagian dari manual ini yang boleh direproduksi, disimpan dalam sistem pengambilan, atau dikirim dalam bentuk
apa pun atau dengan cara apa pun elektronik, mekanik, fotokopi, atau sebaliknya, tanpa izin tertulis sebelumnya dari S EIKO EPSON
CORPORATION.
□ Semua upaya telah dilakukan untuk memastikan keakuratan isi manual ini. Namun, jika ada kesalahan yang terdeteksi, SEIKO EPSO N akan
sangat menghargai informasi tersebut.
Umum Perhatikan: Lainnya nama produk yang digunakan di sini hanya untuk tujuan identifikasi dan mungkin merupakan merek dagang atau
merek dagang terdaftar dari pemiliknya masing-masing. EPSON melepaskan setiap dan semua hak dalam merek tersebut.
BAHAYA Menandakan tindakan pencegahan yang, jika diabaikan, dapat mengakibatkan cedera pribadi yang serius atau fatal. Hati -hati harus
dilakukan dalam melakukan prosedur yang didahului oleh BAHAYA Pos.
PERINGATAN Sinyal peringatan yang, jika diabaikan, dapat mengakibatkan kerusakan peralatan.
Tindakan pencegahan yang disebutkan di bawah ini harus selalu diperhatikan ketika melakukan prosedur perbaikan / pemeliharaan .
BAHAYA
1. SELALU MEMUTUSKAN PRODUK DARI SUMBER DAYA DAN PERANGKAT PERIPHERAL MELAKUKAN PROSEDUR PEMELIHARAAN ATAU
PERBAIKAN APA PUN.
2. TIDAK ADA PEKERJAAN YANG HARUS DILAKUKAN DI UNIT OLEH ORANG-ORANG YANG TIDAK SESUAI DENGAN TINDAKAN KESELAMATAN DASAR
SEBAGAI DICTATED UNTUK SEMUA TEKNIK ELEKTRONIK DALAM JALAN KERJA MEREKA.
3. KETIKA MELAKUKAN PENGUJIAN SEBAGAI DICANTI DALAM PANDUAN INI, JANGAN MENGHUBUNGKAN UNIT KE SUMBER DAYA LISTRIK SAMPAI DI
INSTRUKSI UNTUK MELAKUKAN SO. KETIKA KABEL SUPPLY POW ER HARUS DIHUBUNGKAN, GUNAKAN PERHATIAN EKSTRIM DALAM BEKERJA PADA
SUPPLY POW ER DAN KOMPONEN ELEKTRONIK LAINNYA.
4. KETIKA PUTUSAN ATAU PERAKITAN PRODUK, PASTIKAN UNTUK MEMAKAI SARUNG TANGAN UNTUK MENGHINDARI INJURIER DARI BAGIAN LOGAM DENGA N
TEGANGAN SHARP.
PERINGATAN
1. PERBAIKAN PADA PRODUK EPSON HARUS DILAKUKAN SAJA OLEH TEKNIK PERBAIKAN BERSERTIFIKAT EPSON.
2. PASTIKAN BAHW A TEGANGAN SUMBER ADALAH SAMA SEBAGAI TEGANGAN TINGKAT, TERDAFTAR PADA NOMOR SERI / TINGKAT PELAT. JIKA PRODUK
EPSON MEMILIKI PERINGKAT AC PERINGKAT YANG BERBEDA DARI SUMBER DAYA TERSEDIA, JANGAN MENGHUBUNGKANNYA KE SUMBER DAYA.
3. SELALU MEMERIKSA BAHW A PRODUK EPSON TELAH TERPUTUS DARI SUMBER DAYA SEBELUM MENGHAPUS ATAU MENGGANTI PAPAN SIRKUIT
TERCETAK DAN / ATAU CHIPS INDIVIDUAL.
4. UNTUK MEMPERLINDUNGI MIKROPROSESOR DAN SIRKUITRI SENSITIF, GUNAKAN PERALATAN STATIS DISCHARGE, TERSEBUT SEBAGAI STRAPS W RIST
ANTI STATISTIK, KETIKA MENGAKSES KOMPONEN INTERNAL.
5. JANGAN GANTI KOMPONEN FUNGSI SEPENUHNYA DENGAN KOMPONEN YANG TIDAK DIPRODUKSI OLEH EPSON. JIKA IC SUMBE R KEDUA ATAU
KOMPONEN LAINNYA YANG TIDAK TELAH DISETUJUI DIGUNAKAN, MEREKA BISA MENYEBABKAN KERUSAKAN PADA PRODUK EPSON, ATAU BISA
MENGOSONGKAN GARANSI YANG DITAW ARKAN OLEH EPSON.
Tentang Manual Ini
Manual ini menjelaskan fungsi dasar, teori operasi listrik dan mekanik, prosedur perawatan dan perbaikan printer. Instruksi dan prosedur yang termasuk di
sini dimaksudkan untuk teknisi perbaikan berpengalaman, dan perhatian harus diberikan pada tindakan pencegahan pada halaman s ebelumnya.
Revisi:
• Halaman -70 “Pesan peringatan dan hati-hati” ditambahkan.
B 5 April 2001 • Halaman -107 “Peta Alamat EEPROM” ditambahkan.
• Halaman -111 “Tata Letak Komponen” ditambahkan.
• Halaman -124 “Papan C294MAIN-B” ditambahkan.
Revisi:
C 19 April 2001 • Halaman -117 “LX-1170 Diagram Meledak” ditambahkan.
• Halaman -121 "Daftar suku cadang untuk LX-1170" ditambahkan.
ISI
Bab 1 DESKRIPSI PRODUK 1.5.1 ESC / P231 ...........................................................................................................
1.5.2 IBM 2390 Plus Emulasi32 ..................................................................................
1.1 FITUR9 ........................................................................................................................ 1.5.3 Perintah Dua Arah33 ...........................................................................................
1.2 SPESIFIKASI10 ......................................................................................................... 1.5.3.1 Balas Printer Status35 .................................................................................
1.2.1 Pencetakan Spesifikasi10 .................................................................................... 1.5.3.2 Perintah paket36 ..........................................................................................
1.2.2 Kertas Memberi makan14 ................................................................................... 1.6 Inisialisasi ................................................................................................................ 37
1.2.3 Spesifikasi Listrik16 ............................................................................................
1.7 Spesifikasi Kertas ................................................................................................... 38
1.2.4 Kondisi Lingkungan16 ........................................................................................
1.2.5 Keandalan16 ........................................................................................................ 1.8 Spesifikasi Fisik ...................................................................................................... 41
1.2.6 Pita Cartridge16 .................................................................................................. 1.8.1 Spesifikasi Fisik untuk LX-300 + 41 ..................................................................
1.2.7 Keamanan Persetujuan17 ................................................................................... 1.8.2 Spesifikasi Fisik untuk LX-117042 ....................................................................
1.2.8 CE Penandaan17 ................................................................................................. 1.9 Aksesoris.................................................................................................................. 43
1.2.9 Dicetak Area18 ...................................................................................................
1.3 Spesifikasi Antarmuka .......................................................................................... 21 Bab 2 Prinsip Operasi
1.3.1 Antarmuka Paralel (Saluran Maju) 21 ...............................................................
1.3.2 Antarmuka Paralel (Terbalik Saluran) 23.......................................................... 2.1 Gambaran ............................................................................................................... 45
1.3.3 Serial Interface24 ................................................................................................ 2.2 Mekanisme Pencetak ............................................................................................. 46
1.3.4 Antarmuka Seleksi25 .......................................................................................... 2.2.1 Printhead47 ..........................................................................................................
1.3.5 Host Pencegahan dari Transfer Data Waktu habis25 ....................................... 2.2.1.1 Bel Function47 ............................................................................................
1.3.6 IEEE1284.4 protokol25 ....................................................................................... 2.2.2 Gerbong Mekanisme48 .......................................................................................
1.4 Operasi ..................................................................................................................... 26 2.2.2.1 Kecepatan tinggi lewati metode50 .............................................................
1.4.1 Panel Kontrol26 .................................................................................................. 2.2.3 Pita Mekanisme50................................................................................................
1.4.1.1 Switches26 .................................................................................................. 2.2.3.1 Pergeseran Pita Tinta Mekanisme50 ..........................................................
1.4.1.2 LED27 2.2.3.2 Mekanisme Mengemudi Pita Warna (Opsi) 50 .........................................
1.4.1.3 Buzzer27 ...................................................................................................... 2.2.4 Celah Platen Mekanisme Penyesuaian52 ...........................................................
1.4.2 Fungsi28 ............................................................................................................... 2.2.5 Umpan Kertas Mekanisme53 ..............................................................................
1.4.2.1 Operasi Biasa28 ........................................................................................... 2.2.5.1 Panjang Halaman Pengukuran54 ...............................................................
1.4.2.2 Operasi di Power-on28............................................................................... 2.2.6 Melepaskan Mekanisme55 ..................................................................................
1.4.2.3 Pengaturan Default28 ................................................................................. 2.2.7 Lain Fungsi Khusus55 .........................................................................................
1.4.2.4 Tawaran. Penyesuaian29............................................................................. 2.2.7.1 Hemat energi mode55 .................................................................................
1.4.3 Kesalahan30 ........................................................................................................ 2.2.7.2 Mode Diam55 ..............................................................................................
1.5 Kode kontrol ........................................................................................................... 31 2.3 Pengoperasian Sirkuit Listrik Prinsip56 .................................................................
2.3.1 Papan Utama Listrik Sirkuit56 ............................................................................
2.3.2 C294PSB / C294PSE Dewan58 ......................................................................... PF Perakitan Motor Penghapusan86 ....................................................
2.3.2.1 Listrik Circuit58 ......................................................................................... 4.2.7.11 Umpan Kertas Mekanisme Pembongkaran87 .....................................
4.2.7.12 Kertas Panduan Penghapusan88 ..........................................................
1
DESKRIPSI PRODUK
LX-300+/1170 Revision C
Dukungan
kertas
Kartrid pita
Penutup pemandu
kertas
Panduan
kertas
Tuas ketebalan Penutup
kertas printer
Tuas pelepas kertas
1.2 SPESIFIKASI Tabel 1-1. Kecepatan Cetak dan Kolom yang Dapat Dicetak
Mode pencetakan Pitch karakter (cpi) Kolom yang dapat Kecepatan
dicetak pencetakan (cps)
1.2.1 Spesifikasi pencetakan Draf terkondensasi 137 (LX-300 +)
17 191
□ Mencetak metode: Impact dot matriks 233 (LX-1170)
□ Tabel karakter dan tipografi: Tabel 1-3. Tabel Karakter dan Tipografi
Tabel karakter Font bitmap
Tabel 1-3. Tabel Karakter dan Tipografi
NLSP Meja miring EPSON Draft
Tabel karakter Font bitmap
Versi: PC 437 (AS, Eropa Standar) EPSON Roman
Versi Meja miring EPSON Draft kapan
Standar PC 437 (AS, Eropa Standar) EPSON Roman EPSON Sans serif
□ Kertas jalur: Manual insertionRear in, atas di luar Pakan umpan traktor (bawah) Kertas kontinu (Satu lembar dan
beberapa bagian)
CSFRear di, atas di luar
Dorong TractorDengar, atas di luar Label
Tarik TractorRear atau bagian bawah, atas di luar
□ Tuas ketebalan kertas:
□ Penspasian baris: 4.23mm (1/6 inci) atau dapat diprogram dengan Tuas ketebalan kertas harus diatur pada posisi yang tepat seperti yang ditunjukkan
penambahan ; di bawah ini.
LX-300 +: 0,118mm (1/216 inci)
LX-1170: 0,059mm (1/432 inci) Tabel 1-5. Tuas Ketebalan Kertas
□ Makan kecepatan: 4.23mm (1/6 inci makan)
LX-300 + 88msec
LX-117063msec Terus Menerus
feed0.76MPS LX-300 LX-1170
(m / dtk) +
[3,0 IPS (inci / detik)] Ketebalan Ketebala Ketebalan Ketebala
Posisi kertas kertas
□ Memasukkan Penyangga Data: 8 Kbyte tuas (inci)
n kertas
(inci)
n kertas
(mm) (mm)
□ Tuas pelepas: Min. Maks. Min. Maks.
Tuas pelepas harus diatur sesuai dengan tabel berikut;
-1 - - - - - -
Tabel 1-4. Lepaskan Lever lebih dari lebih dari
0 (0,0024) (0,0071) (0,0024) (0,0071)
0,06 0,06
Posisi tuas Jalur kertas / Pengumpan Kertas / Media
hingga hingga 0,18
Gesekan Penyisipan manual (belakang) Potong lembaran (Satu lembar dan 0,18
■ Input frequency range:49.5 to 60.5 Hz □ Printhead life:400 million strokes / wire (Black) LX-
300+100 million strokes / wire (Color)
■ Rated current:0.3 A (max. 0.7A)
■ Power consumption:Approx. 23W (ISO/IEC10561 Letter pattern) 1.2.6 Ribbon Cartridge
Energy Star Complaint
□ Type:Fabric
■ Insulation resistance:10M min. Color:Black
(between AC line and chassis, DC 500V) Ribbon life:3 million characters
■ Dielectric strength:AC 1500 Vrms. 1 min. (Draft 10 cpi, 14 dots/character)
(between AC line and chassis) □ Type:Fabric
Color:Black, Magenta, Cyan and Yellow Ribbon
life:
■ Black1 million characters (Draft 10 cpi, 14 dots/character)
■ Magenta0.7 million characters (Draft 10 cpi, 14 dots/character)
1.2.8 CE Marking
230 V & UPS version:
■ Low voltage directive 73/23/EEC:EN60950
■ EMC Directive 89/336/EEC:EN55022 class B
EN61000-3-2
EN61000-3-3
LX-300+ only:EN50082-1
IEC801-2
IEC801-3
IEC801-4
LX-1170 only:EN55024
1.2.9 Printable Area Table 1-6. Printable Area for Cut Sheet
□ Cut sheets Single Sheet Multi Part
TM
Perforatio
n
PrintableArea
PrintableArea
BM
Perforation
PL (Length) Refer to 1.7 "Paper Specifications" PW (Width) Refer to 1.7 "Paper Specifications"
BM
□ BUSY signal is active (HIGH level) under the conditions below: Table 1-12. Connector Pin Assignment and Signals (Forward Channel)
■ In the process of receiving data Signal
Return
Pin No. GND In/Out Functional Description
■ In the condition of being input buffer full Name
Pin
■ In the condition of being -INT signal active (low level) 8 DATA7 26 In bit6
■ During hardware initialization 9 DATA8 27 In bit7:MSB
■ In the condition of being -ERROR or PE signal is active (low level, high This signal (negative pulse) indicates that the
level, respectively) 10 -ACKNLG 28 Out printer has received data and is ready to accept
next one.
■ In the self test mode
■ In the adjustment mode This signal’s high level means that the print is
11 BUSY 29 Out
not ready to accept data.
■ In the default-setting mode
This signal’s high level means that the printer is
12 PE 28 Out
□ -ERROR signal is active (low level) under the conditions below: in a state of paper-out error.
■ In the condition of a paper-out error Always at high level when the printer is
■ 13 SLCT 28 Out
powered on.
In the condition of a release lever error
14 -AFXT 30 In Not used.
□ PE signal is active (high level) under the condition below:
31 -INIT 30 In This signal’s negative pulse initializes printer.
■ In the condition of a paper-out error
This signal’s low level means the printer is in a
32 -ERROR 29 Out
Table 1-12. Connector Pin Assignment and Signals (Forward Channel) state of error.
6 DATA5 24 In bit4
NOTE: In/Out shows the direction of signal flow from the printer’s point of view.
7 DATA6 25 In bit5
1.3.2 Parallel Interface (Reverse Channel) Table 1-13. Connector Pin Assignment and Signals (Reverse Channel)
□ Transmission mode:IEEE-1284 nibble mode Return
□ Adaptable connector:See 1.3.1 "Parallel Interface (Forward Channel)" Pin No. Signal Name GND In/Out Functional Description
Pin
□ Synchronization:Refer to the IEEE-1284 specification
1 HostClk 19 In Host clock signal.
□ Handshaking:Refer to the IEEE-1284 specification
Parallel input data to the printer.
2 DATA1 20 In
□ Signal level:IEEE-1284 level 1 device See 1.3.1 bit0:LSB
"Parallel Interface (Forward Channel)"
3 DATA2 21 In bit1
□ Data transmission timing:Refer to the IEEE-1284 specification
4 DATA3 22 In bit2
□ Extensibility request:The printer responds to the extensibility request
5 DATA4 23 In bit3
affirmatively, when the request is 00H or 004H, which means;
6 DATA5 24 In bit4
00H: Request for nibble mode of reverse channel transfer
04H: Request device ID in nibble mode of reverse channel transfer 7 DATA6 25 In bit5
□ Device ID: The printer sends following device ID string when it is requested. 8 DATA7 26 In bit6
Table 1-13. Connector Pin Assignment and Signals (Reverse Channel) Table 1-14. Connector Pin Assignment and Signals
Return
Pin
Pin No. Signal Name GND In/Out Functional Description Signal Name In/Out Functional Description
No.
Pin
2 TXD Out Transmit data.
17 Chassis -- -- Chassis GND.
20 DTR Out Indicates that the printer is ready to receive data or not.
16, 33, Signal GND.
GND -- --
19-30 11 REV Out Connected directly to the DTR signal.
15, 34 NC -- -- Not connected. Request to send. Always SPACE level when the printer
4 RTS Out
is powered on. Pulled up to +12V via 4.7K resistor.
NOTE: The DTR signal is MARK and XOFF code (DC3, 13H) is transmitted
when the rest of the input buffer becomes 256 bytes. The DTR signal is
SPACE and XON code (DC1, 11H) is transmitted when the rest of the
input buffer is regained 256 byte.
Pause On --- --- *The description (.) and (-) in the above shows how the beeper sounds.
(.): Beeper sounds approx. 100ms and interval is approx. 100ms.
Paper out error On On ---
(-): Beeper sounds approx. 500ms and interval is approx. 100ms.
Release lever error On --- ---
*1 Pause (Orange)
-It is on when the printer is paused, and it is off when the printer is not paused.
-It blinks when Micro Adjust is enabled.
*2 Paper Out (Red)
-It is on when the printer is in the Paper out status, and it is off when the printer is out
of this status.
1.4.3 Errors
□ Paper out error:
When the printer fails to feed a sheet, it goes a paper out error.
□ Release lever error:
When release lever position is wrong, it goes a release lever error.
□ Fatal errors:
Carriage control error and Power supply voltage error.
Condensed DC2, SI
Table 1-20. ESC/P2
Double-height ESC w
Classification Operation Command
Double-Strike ESC G, ESC H
General Operation Initialize Printer ESC@
Super-/ Subscript ESC T, ESC S
Unidirectional Printing ESC U
Underline ESC-
CSF Mode Control ESC EM
Spacing Intercharacter Space ESC Space
Paper feeding Form Feed FF
Character handling Character Table ESC t, ESC (t
Line Feed LF
International Character ESC R
ESC 0, ESC 1, ESC 2, ESC3,
Line Spacing
ESC A User-Defined Characters ESC%, ESC &, ESC:
Page format Page Length ESC C, ESC C0, ESC (C Upper Control Codes ESC6, ESC7
1.5.2 IBM 2390 Plus Emulation Table 1-21. IBM 2390 Plus emulation
Classification Operation Command
Table 1-21. IBM 2390 Plus emulation
Font selection Pitch DC 2, ESC P, ESC:
Classification Operation Command
Bold Font ESC E, ESC F
General Operation Nop NUL, DC3
Master Select ESC I
Off Line ESC j
Print Quality ESC [d
Buzzer BEL
Select Font and Pitch ESC [I
Cancellation CAN
Font enhancement Double-Width DC4, SO, ESC SO, ESC W
Select / Deselect DC1, ESC Q
Enlarge and Life Space ESC [@
Initialize Printer ESC [K
Condensed SI, ESC SI
Unidirectional Printing ESC U
Double-Strike ESC G, ESC H
Select Auto Sheet Feeder ESC [F
Super-/ Subscript ESC T, ESC S
Paper feeding Form Feed FF
Underline ESC -
Line Feed,
LF, ESC5
Auto Line Feed Line / Score ESC_
■ Reply Printer Settings:XX[nL][nH][01H][ml]...[mx] Select character table “CT” 02H 00H 00H m1
m1=0 (Table0), 1(Table1)
XX is a string of 2 ASCII characters of defining a feature of the command. Following
[nL][nH] is two byte hexadecimal value that denotes the length of the [00H] and Assign character table “AT” 04H 00H 00H m1 m2 m3
[ml]...[mx] parameters. Last [m1] ... [mx] parameters are used to describe the detailed m1=0(Table0), 1(Table1)
command function and represent printer settings. m2, m3=(ESC/P2 Character Table No.)*4
Table 1-23. Note for Table 1-22 Table 1-25. NLSP ver. only
m2 m3 Character table m2 m3 Character table
m1 set by AT/CT m2 set by AT m3 set by AT
0EH 30H PC866 UKR 29H 00H PC 708
0 0 0
0FH 00H PC869 2AH 00H PC720
1 All parameters that can be set
0DH 20H PCAR_864 7FH 02H ISO 8859-2
*4 m2 and m3 apply to the following ID number. (See Table 1-24 & Table 1-25.)
1BH 00H MAZOWIA 2DH 00H PC771
Table 1-24. Std and NLSP ver.
*5 m1=0 to 7 only
m2 m3 Character table m2 m3 Character table
<Remote commands>
00H 00H Italic 19H 00H BRASCII
01H 00H PC437 1AH 00H Abicomp Table 1-26. Bi-Directional Commands
03H 00H PC850 7FH 01H ISO Latin1 Function Code/ Parameter Save
07H 00H PC860 23H 00H Roman8 Set page length “PG” 05H 00H 00H p1 p2 m1 m2
p1=0(Continuous paper), p2=0(Rear),
08H 00H PC863 2CH 00H PC858 p1=1(CSF), p2=0(bin1)
09H 00H PC865 1DH 0FH ISO 8859-15 p1=2(Manual insertion), p2=0(rear)
O
-Page legth=m1+256*m2,
18H 00H PC861 0.118mm (1/216inch)
648 (76.2mm(3inch)) <= m1+256*m2 <=
4752(558.8mm(22 inch))
Table 1-25. NLSP ver. only
Set Top margin “TP” 05H 00H 00H p1 p1 m1 m2
m2 m3 Character table m2 m3 Character table
p1=0(Continuous paper), p2=0(Rear),
01H 10H PC437 Greek 1CH 00H Code MJK p1=1(CSF), p2=0(bin1)
p1=2(Manual insertion), p2=0(rear)
05H 00H PC853 1DH 07H ISO 8859-7 O
-Top margin=m1+256*m2,
0.118mm (1/216inch)
06H 00H PC855 1FH 00H ISO Latin 1T
36 (4.2mm) <= m1+256*m2 <= 288 (8.5mm +
0AH 00H PC852 20H 00H Bulgaria 25.4mm(1inch))
0BH 00H PC857 21H 00H Hebrew 7 Turn unidirectional mode on/ “PD” 02H 00H 00H m1
O
off m1=0(Bi-d.), 1(Uni-d.)
0CH 00H PC862 22H 00H Hebrew 8
Turn auto tear-off on/off “TO” 02H 00H 00H m1
0DH 00H PC864 24H 00H PC 774 O
m1=0(off), 1(on)
0EH 00H PC866 25H 00H Estonia Turn auto line feed on/off “LF” 02H 00H 00H m1
O
0EH 20H PC866 LAT. 28H 00H PC APTEC m1=0(off), 1(on)
Inquire starting date/month/ “SD” 01H 00H 01H In the idle state “04”
year “@BDC” SP “PS” CR LF “SD:” <nn1> <nn2> -
In the pose state “05”
<nn3>“;” FF
Continuous paper (rear) “0000” Device ID request “di” 01H 00H 01H
Continuous paper (bottom) “0001” Device ID reply (*1) “@EJL” SP “ID” CR LF <Device ID string> FF
Cut sheet (rear) “0200” State-Reply request “st” 01H 00H 01H
CSF Single bin “0100” State-Reply (*2) “@BDC” SP “ST” CR LF <printer status string> FF
“XX:;” FF
□ characteristic status code No support command
(XX is the command string being invalid.)
Table 1-30. Characteristic Status Code NOTE: (*1) The reply string is as same as BDC-ID Reply.
location size type Refer to NOTE: (*2) The reply string is as same as BDC-ST Reply.
Structure version +0 2bytes “02” fixed -
1.6 Initialization
□ Power-on initialization
The initialization of this level is activated by power-on or cold-reset command
(remote RS command).
This initialization is;
■ to initialize the printer mechanism.
■ to execute Operator initialization.
□ Operator initialization
The initialization of this level is activated by -INT signal (negative pulse).
This initialization is;
■ to clear the all buffers of data.
■ to cancel the download character definition.
■ to make the printer stand-by state, if no errors occur.
■ to execute Software initialization.
□ Software initialization
The initialization of this level is activated by the control code ESC@.
This initialization is;
■ to clear the unprinted data.
■ to make the printer’s setting defaults.
□ Cut sheet (single sheet, not multi part) Table 1-33. Cut Sheet (Multi part)
Minimum Maximum
Table 1-32. Cut Sheet (single sheet, not multi part)
(inch) (3.9) (10.1)
Manual insertion CSF single-bin Width
(mm) 100 (257)
Minimum Maximum Minimum Maximum (inch) (3.9) (14.3)
Length
(3.9) (10.1) (7.2) (8.5) (mm) 100 (364)
(inch)
Width
(mm) 100 257 182 216 Copies 1 original + 4 copies
(inch) (3.9) (14.3) (10.1) (14.0) Total (inch) (0.0047) (0.015)
Length
(mm) 100 364 257 356 Thickness (mm) 0.12 0.39
(inch) (0.0025) (0.0055) (0.0028) (0.0055) Weight (one
Thickness (g/m2) 52 90
(mm) 0.065 0.14 0.07 0.14 sheet of
(lb.) (14) (24)
multipart)
(g/m2) 52 90 64 90
Weight
(lb.) (14) (24) (18) (24) Plain paper, Reclaimed paper
Quality
Not curled, not folded, not crumpled.
Plain paper, Reclaimed paper Plain paper, Reclaimed paper
Quality Not curled, not folded, not Not curled, not folded, not Jointing Line glue at the top or one side of form.
crumpled crumpled
NOTE: Printing on reclaimed paper is available only under normal
NOTE: Printing on reclaimed paper is available only under normal temperature and humidity conditions.
temperature and humidity conditions.
Table 1-34. Envelope Table 1-35. Continuous Paper (Single sheet and Multi Part)
Minimum Maximum Rear Entry Bottom Entry
□ Labels
63.5 mm (2.5 inch) min.
Table 1-36. Continuous Paper with Labels
Rear Entry Bottom Entry
23.8 mm
Min. Max. Min. Max. (15/16inch) Label
min.
Label size --- See the figure below.
NOTE: Continuous paper with labels should be inserted from the bottom
entrance.
1.9 Accessories
Table 1-38. Enclosed Parts
Enclosed Items Quantity
User's manual 1
Driver disk 1
2
OPERATINGPRINCIPLES
LX-300+/1170 Revision C
2.1 Overview
LX-300+/1170 consists of the printer mechanism and electric circuit boards.
Printer
Power Supply Main Board Mechanism
Board C294MAIN/
C294PSB/PSE C294MAIN-B
Panel
Board
C294PNL
□ Circuit board
■ Main (control circuit):C294MAIN(LX-300+)
C294MAIN-B Board(LX-300+/LX-1170)
■ Power:C294PSB / C294PSE Board
■ Panel:C294PNL Board
Release detector
Release mechanism
Timing belt
Adjust lever
Carriage motor
Ribbon
2.2.1 Printhead
The table below shows the printhead specifications.
CR MOTOR
This printer uses stepping motor for CR motor. Open loop control switches the phases
according to the setting period and this mechanism enables the carriage to move until the
appointed position. The table below is the CR motor specifications..
Table 2-3. CR Motor Specifications
Item Specification
Motor type 2-phase/200-pole hybrid stepping motor
Coil resistance 5.7 ±10% (25°C)
Control method Bi-polar drive
Phase drive 2-2 phase, 1-2 phase, W1-2 phase
Drive voltage 36.75 ±1.75 V
Minimum Resolution:
CR feed pitch
0.212 mm (1/120”) (1-2 phase, 2 pass)
The printer mechanism initializes when the power is applied or when recovering from The following is PG_SW specification.
the energy saving mode.
Table 2-9. PG_SW Detector Specifications
□ Color mechanism initialization
Item Specification
Color mechanism initialization shifts color mechanism for the black ink area to
be at the home position. Color mechanism initialization shifts the carriage at the Method Mechanical contact method
same time to prevent the ribbon from hanging on the printhead. Switching rate 0.6 to 1.0 mA, 5 VD±5%
When the buffer is cleared or when the printer is under the pause condition, the • PG=0: close
Switching mode
color mechanism initializes and waits for the next printing command. • PG=0-4: open
This mechanism is to adjust the distance between the platen and the printhead (platen
gap) according to the paper thickness. Carriage guide shaft
The following is the components of the LX-300+/1170 platen gap adjustment mechanism Carriage
and its explanation. (Refer to Refer to Figure 2-5.) Parallelism adjust
bushing Parallelism adjust
□ Carriage:Mounts the printhead. bushing
PG_SW
□ Carriage guide shaft:Shifts the carriage horizontally.
□ Adjust lever and Parallelism adjust bushing:
Installed at the both ends of the carriage guide
shaft
□ Platen gap detector (PG_SW)
Carriage guide shaft is eccentric toward the adjust lever rotating center. Due to this, when
rotating the adjustment lever back and forth, the printhead shifts toward and against the
Printer mechanism
platen to adjust the platen gap. When printing on thick paper such as postcards and
Printhead
envelops, set the adjust lever over the 1st level. PG detector shifts the printer to the copy Platen gap
Adjust lever
mode from the printing mode. Printing speed will be lowered but it prevents wire from Platen
breaking off.
Carriage
2.2.6 Release Mechanism The table below shows the release detector specifications.
This mechanism switches the flow of PF motor driving forth between to the friction feed Table 2-13. Release Detector Specifications
and to the tractor feed. Item Specification
Method Mechanical contact method
Compression spring Tractor gear Switching rate 0.6 to 1.0 mA, 5 VD±5%
Plain • Friction: open
washer Switching mode
Release lever • Tractor: close
Paper Release detector
advance
reduction
2.2.7 Other Special Functions
gear
2.2.7.1 Energy saving mode
This function saves electric consumption when the printer is in the standby mode. This
mode turns hold current of PF motor, CR motor and CS motor OFF.
PF motor
2.3 Electrical Circuit Operating Principles □ C294 MAIN Board Block Diagram
Control
Panel
HP
sensor
RPE
Sensor
Release Sensor
BPE
Sensor
PG
Sensor
NOTE: *: Core voltage of CPU and G/A is 3.3V and it is generated by the
regulator IC on the MAIN board form +5VDC.
3
TROUBLESHOOTING
LX-300+/1170 Revision C
This chapter describes how to troubleshoot problems when any problems occurred to the
printer. Refer to troubleshooting flowcharts in this chapter to identify a defective part and
an appreopreate repair for it. Initialization
Check
■ Never touch printhead and any motors right after printing since
WARNING Check performance by self-
they are highly heated.
check function.
■ When disassembling the printer, be sure to disconnect the
power cable and remove the interface cable.
Does any
trouble occur?
■ Be sure to use specified tools for servicing to maintain the
CAUTION
quality.
■ Make sure to apply specified oil, grease and glue.
■ Perform adjustment as specified. Identify problems from
symptoms.
Perform
maintenance.
Troubleshooting Overview 61
LX-300+/1170 Revision C
Troubleshooting Troubleshooting 62
LX-300+/1170 Revision C
Troubleshooting Troubleshooting 63
LX-300+/1170 Revision C
Table 3-3. Control Panel LED Does Not Light On. Table 3-5. When Power is Applied, the Printer Becomes Fatal Error.
Cause Check Point Y/N Solution Cause Check Point Y/N Solution
Check the electric circuit and CR motor harness is Is CR motor harness
Blowout of a fuse on Is a fuse on the power
YES printer mechanism. If there is no not connected CN10 connected NO Connect it properly.
the power board. board blew out?
short circuit, replace the fuse. properly. properly?
Are connectors CR motor is defective. - - Replace the CR motor.
Connector is not
connected to the
connected to the NO Replace the power board. HP detector harness is Is HP detector
power board NO Connect it properly.
power board. not connected harness CN3
properly?
properly connected properly?
Power switch is Is conductivity of the HP detector is
YES Replace the power board. - - Replace the HP detector.
defective. switch is OK?
defective.
Are +5VDC and Power board is Is power voltage
Power board is NO Replace the power board.
+35VDC OK when NO Replace the power board. defective. normal?
defective.
the power is on?
Replace the main board and printer
Power board and the - - -
Is CN8 connected mechanism.
main board are not NO Connect CN8 properly.
properly?
connected properly. Table 3-6. Self Test Print is Abnormal.
Main board is Cause Check Point Y/N Solution
- - Replace the main board.
defective.
Any of CN3 to CN12
Control panel harness Is the harness of the Are all connectors
is not connected to NO Connect them properly.
is not connected control panel NO Connect the harness properly. connected properly?
the main board
properly. connected properly? properly.
Control panel board Printhead driver is
- - Replace the main board.
or harness is - - Replace the control panel. defective.
defective. Are rows aligned
properly when bi-
Table 3-4. Printer Mechanism Does Not Operate. Bi-d is not correct.
directional printing
NO Adjust Bi-D.
Cause Check Point Y/N Solution is proceeded?
Any of CN3 to CN12 Is there any dot
Are all connectors Printhead is defective. YES Replace the printhead.
is not connected to NO Connect them properly. missing?
connected properly?
the main board
Head FFC is not
properly.
connected properly or - YES Replace the head FFC.
Main board is broken.
- - Replace the main board.
defective.
Is printing too light /
Printer mechanism is YES Adjust the platen gap.
- - Replace the printer mechanism. Platen gap is not weak?
defective.
correct. Is there any dirt on
YES Adjust the platen gap.
printed documents?
Ribbon mask is Is there any dirt on
YES Replace the ribbon mask.
defective. printed documents?
Troubleshooting Troubleshooting 64
LX-300+/1170 Revision C
Table 3-6. Self Test Print is Abnormal. Table 3-9. Printing Operation is Abnormal When it is On-Line.
Cause Check Point Y/N Solution (Self-Test is Normal.)
Ribbon mechanism is Is ribbon advanced Cause Check Point Y/N Solution
NO Replace the ribbon mechanism parts.
defective. properly?
Check the initial
Printer mechanism is Initial setting is setting with the Reset the setting or use the EEPROM
- - Replace the printer mechanism. NO
defective. wrong. default setting. Is it clear to reset setting to the default.
OK?
Table 3-7. Paper Feed is Abnormal. Interface cable is
Cause Check Point Y/N Solution Are cables connected
not connected NO Connect them properly.
properly?
RPE detector or BPE NO Replace the sensor. properly.
Check the sensors.
detector is defective or Interface cable is
Is there any Check the connection to the main - - Replace the interface cable.
not connected YES defective.
abnormality? board.
properly.
Main board is
- - Replace the main board.
Switch the release defective.
lever. Is the paper Replace the printer mechanism or
Paper switching NO Firmware is Is the firmware
loading direction check the connection. NO Replace the firmware.
mechanism is defective. version latest?
switched?
defective.
Can the release lever Replace the release sensor or
NO
be switched? check the connection.
When the power is
Printer mechanism
off, can the printer
paper loading Replace the printer mechanism or
feed paper by NO
mechanism is paper loading mechanism parts.
rotating the platen
defective.
knob manually?
PF motor is defective. Is PF motor normal? NO Replace the PF motor.
PF motor driver is
- - Replace the main board.
defective.
Troubleshooting Troubleshooting 65
LX-300+/1170 Revision C
WARNING When repairing the unit, make sure to turn the printer off and plug
off the power cable except when this manual specifies to keep the
power on.
Troubleshooting Troubleshooting 66
LX-300+/1170 Revision C
Troubleshooting Troubleshooting 67
LX-300+/1170 Revision C
Troubleshooting Troubleshooting 68
CHAP TE R
4
DISASSEMBLY AND
ASSEMBLY
LX-300+/1170 Revision C
See the precautions given under the handling “WARNING” and “CAUTION” in the Needle-nose pliers B740400100
following column when disassembling or assembling the product. Nipper B740500100
■ Disconnect the power cable before disassembling or assembling Tweezers B741000100
WARNING
the printer.
■ Never touch the printer right after it finishes printing, for the Soldering bit B740200100
printhead is highly heated. E ring holder #2.5 B740800400
■ If you need to work on the printer with power applied, strictly
follow the instructions in this manual. + driver No.2 B743800200
■ Always wear gloves for disassembly and reassembly to avoid Box driver (opposite side distance: 7mm) B741700200
iujury from sharp metal edges.
Thickness gauge B776702201
■ To protect sensitive microprocessors and circuitry, use static
discharge equipment, such as anti-static wrist straps, when
accessing internal components. NOTE: All tools are available in market.
■ Use only recommended tools for disassembling, assembling or Table 4-2. Recommended Tools-2
CAUTION
adjusting the printer. Device Specification
■ Observe the specified torque when tightening screws.
Multimeter -
■ Apply lubricants and adhesives as specified.
■ Make the specified adjustments when you disassemble the Oscilloscope 50MHz
printer.
(See Chapter 5 for details.) NOTE: Only component level repairing service requires oscilloscope.
■ When performing an adjustment, follow the method described
in this manual.
4.1.3 Service Checks After Repair Table 4-4. Check List for Repaired Printer
Category Component Item to Check Check
Before returning the printer back to the user, use the check list below to confirm the
quality of the repaired printer. Version Up ROM version Latest ROM version ________ □OK □NG
Ink ribbon Is ribbon removed? □OK □NG
Table 4-4. Check List for Repaired Printer Transportation Are all the relevant parts included in
accessories □OK □NG
Category Component Item to Check Check the shipment?
Is dot missing? □OK □NG
Printhead
Are any wires broken? □OK □NG
Does carriage move smoothly?
□CR movement is not noisy?
□OK □NG
□CR mechanism is not dirty?
Carriage
□CR mechanism is not oily?
mechanism
Is the CR motor assembly at the
correct temperature? □OK □NG
(Not overheating?)
Is paper advancing smoothly?
□PF movement is not noisy?
□OK □NG
□PF mechanism is not dirty?
Printer Paper feed
□PF mechanism is not oily?
Mechanism mechanism
Is the PF motor assembly at the correct
temperature? □OK □NG
(Not overheating?)
Are all the types of paper fed
□OK □NG
smoothly?
Paper path Does the tractor feed paper smoothly? □OK □NG
Is the paper path clear of obstructions? □OK □NG
Is the platen free of damage? □OK □NG
Ribbon mask Is the ribbon mask free of distortion? □OK □NG
Test printing Is the test printing successful? □OK □NG
Online
Is the online printing successful? □OK □NG
printing
Is the platen gap adjusted correctly? □OK □NG
Printhead
Is Bi-d adjustment value correct? □OK □NG
Adjustment
Have all user changeable settings been
Initial setting □OK □NG
reset to the default value?
4.2 Disassembly and Assembly The figure below is the disassembly flowchart for main component.
This section explains the disassembly and assembly of Product Name. Unless otherwise
specified, assembly can be done in the reverse order of the disassembly procedure. START
Anything that service person should pay attention to is described under “Check Point”.
Any adjustment required after assembly is described under “Adjustment”.
4.2.2 "Upper Housing 4.2.1 "Printhead
When you have to remove parts that are not described in this chapter, refer to the exploded Removal" Removal"
diagram on Appendix of this manual.
CAUTION
■ Read 4.1.1 "Precautions" before start disassembling the printer. 4.2.3 "Printer Mechanism 4.2.4 "Board Assembly
■ Remove ink ribbon and paper before disassembling the printer. Removal" and Panel Removal"
CAUTION Check if the printer is powered off before removing the printhead.
ADJUSTMENT When the printhead is replaced, perform the platen gap adjustment.
REQUIRED
CPB (3x10)
4.2.3 Printer Mechanism Removal LX-1170: Remove 4 screws with washer (C.B.B., (W(13), 3x14 F/ZN)
securing the printer mechanism to the lower housing.
1. Remove the upper housing. (See 4.2.2 "Upper Housing Removal".) See Figure 4-4 below.
2. LX-300+: Remove 3 screws (C.B.P., Tite, 3x10 F/ZN;Torque 0.78-0.98
N.M.) securing the upper shield plate to the lower housing.
LX-1170: Remove 4 screws (C.B.P., Tite, 3x10 F/ZN; Torque 0.78-0.98 N.M.)
and 2 screws (C.B.S., Screw, 3x4 F/Zn;Torque 0.78-0.98 N.M.)
securing the upper shield plate to the lower housing.
3. Remove the shield cover.
C.B.P., Tite, 3x10 F/ZN) C.B.B., (W(13), 3x14 F/ZN
Upper Shield Plate C.B.B., (W(13), 3x14 F/ZN
C.B.B., (W(13), 3x14 F/ZN
Printer Mechanism
5. Lift the printer mechanism a little bit and remove harnesses from the main
board assembly.
Printer Mechanism
Main Board Assembly
4.2.4 Board Assembly and Panel Removal 4.2.5 C294MAIN/MAIN-B Board Assembly Removal
1. Remove the upper housing. (See 4.2.2 "Upper Housing Removal".) 1. Remove the upper housing. (See 4.2.2 "Upper Housing Removal".)
2. Remove the panel FFC from the connector of panel board assembly. 2. Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)
3. Remove 3 screws (C.B.P., Tite, 3x10 F/ZN; Torque 0.78-0.98 N.M.) securing 3. LX-1170: Remove 1 screw (C.B.P., Tite, 3x10 F/ZN; Torque 0.78-0.98 N.M.)
the panel board assembly to the lower housing. and the right grounding plate.
4. Remove the panel board assembly from the lower housing. Grounding Plate, Right
CN13
Grounding Cable
CN12
5. Remove the power cable (CN1) connecting to the Power Supply board assembly.
CN8 Remove the power switch from the lower housing.
6. Remove the harness connecting the Power Supply board assembly to the main
Main Board Assembly C.B.P., Tite, 3x10 F/ZN
board assembly. (CN8 of the main board assembly)
Press one edge of CN8 in order to remove or install the harness.
Figure4-7. C294MAIN Board Assembly Removal 7. Remove 4 screws (C.B.P., Tite, 3x10 F/ZN; Torque 0.78-0.98 N.M.) securing
the Power Supply board assembly to the lower housing.
8. Remove the Power Supply board assembly.
START
CBP (3x10) P/S Board Assembly C.B.P., Tite, 3x10 F/ZN 4.2.7.5 "RPE Sensor 4.2.7.7 "HP Sensor
Removal" Removal"
Figure4-9. C294 Power Supply Board Assembly Removal
Gear, 34
dis20_a
Base Frame 4. Rotate right and left bushing, 11 and remove them off from the right / left frame.
5. Remove the platen.
Figure4-11. CR Motor Assembly Removal
Bushing, 11
Right frame
4. Remove the CR shaft grounding plate from the base frame on the left side of the
printer.
PG adjust lever
CR guide shaft
Carriage unit
7.Remove the carriage unit along with the CR guide shaft and PG adjust lever from the
printer mechanism.
Left frame
ADJUSTMENT When the carriage unit is replaced, perform Bi-D adjustment.
REQUIRED
Base frame
Right frame
5. Rotate the right and left parallelism adjust bushing and remove them from
respective frame.
6. Release the PG adjust lever hook, connecting to the left frame.
Gear, 13.2
Paper guide
HP sensor (black)
Base frame
Hook Hook
PG sensor (white)
3. Remove the harness from the sensor (blue). 4.2.7.10 PF Motor Assembly Removal
Release lever position sensor (blue)
1. Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)
2. Remove the platen grounding wire from the platen.
3. Remove 1 screw (C.B.P., Tite, 3x10 F/ZN; Torque 0.59-0.78 N.M.) securing the
PF motor assembly to the right frame.
4. Remove 1 hook at the right frame securing the PF motor assembly to the right frame
and remove the PF motor assembly.
CAUTION When installing the release lever position sensor, be sure to insert it
between the release lever and the right frame.
CHECK When installing the PF motor assembly to the right frame, be careful
POINT to align the position marking pin and motor bracket position
marking hole.
4.2.7.11 Paper Feed Mechanism Disassembly 5.Remove the combination gear, 8.5, 25.2 from the right frame.
Gear, 27.5
CHECK When installing the release lever, be sure to align the marking on the Figure4-24. Paper Feed Mechanism Disassembly
POINT release lever with the marking on the release shaft.
4.Release the hook of the right frame securing the gear, 27.5 and remove the gear, plain
washer 5.2x0.3x10 and the compression spring, 1.18.
4.2.7.12 Paper Guide Removal 8. Release 1 hook at the left frame securing the base frame and remove it by pulling it
to the rear.
1. Remove the printer mechanism. (See 4.2.3 "Printer Mechanism Removal".)
2. Remove the platen. (See 4.2.7.2 "Platen Removal".)
3. Remove the carriage unit. (See 4.2.7.3 "Carriage Unit Removal".)
Base frame
4. Remove the HP sensor. (See 4.2.7.7 "HP Sensor Removal".) Hook at the left frame
dis25_a
Figure4-26. Left Frame Removal
9. Release 1 hook securing the paper guide to the lower paper guide and remove the
paper guide along with the release shaft by pulling it to the left.
5
ADJUSTMENT
LX-300+/1170 Revision C
5.1 Overview
This chapter explains the adjustment required after disassembling the printer. START
Adjustment Overview 89
LX-300+/1170 Revision C
5.1.2 Bi-D Adjustment 5. LX-300+: Load and run the adjustment program “Q80A12V.bas”.
Input “Q80A12V” and press ENTER. Then input “run”.
Adjustment programs here for LX-300+ and LX-1170 are originally used for LX-1170f: Load and run the adjustment program “U10A00V.bas”.
production line. Bi-D adjustment is required in the following cases. Input “U10A00V” and press ENTER. Then input “run” and press ENTER.
Go to step 7.
□ Main board assembly is replaced.
□ Printer mechanism is replaced.
□ Printer mechanism is removed.
Follow the steps below for the platen gap adjustment.
1. Connect the printer and the host computer by parallel interface cable.
2. Turn on the PC and the printer.
3. Set FF paper to the printer.
4. Insert FD that contains the adjustment program and click “GWBASIC.EXE” in
the disk to execute GWBASIC. The following DOS prompt screen appears.
6. LX-300+: The application select screen appears. Input “G” to select “GWBASIC”.
LX-1170: Not applicable.
Adjustment Overview 90
LX-300+/1170 Revision C
7. The program will ask you the production line No. Ignore it and press ENTER. 8. LX-300+: Printer 9/24 pin select screen appears. Use and key to shift “>” mark to
LX-300+: After pressing ENTER, input “1”(model number) to select LX- the left of “(1) 9 pin” and press ENTER to select 9 pin printer.
300+. LX-1170: After pressing ENTER, go to step 8.
Adjustment Overview 91
LX-300+/1170 Revision C
9. The destination setting menu appears. Perform settings referring to Table 5-3, Table 5-3. Destination Setting List
“Destination Setting List,” on page 92.
EUL
(MIDDLE EAST)
EAL DEFSTD
ESP
EHK
LX-1170
EUR NLSP
Conti NLSP
EUL NLSP
(220V)
The destination settings are as follows.Use and key or and key to shift
EUL (120V) DEFSTD
“>” mark to the left of the appropriate destination and press ENTER to select
destination. RUSSIA RISSIAN
LX-300+
EAI
USASTD
EAI (Latin)
EURO
EUL (SCANDINAVIA)
EFS
EURSTD
EIS,
EIB
EDG
EDG(NLSP) NLSP
Adjustment Overview 92
LX-300+/1170 Revision C
10. When you select the destination, the select menu below appears. Use and key to 12. “Main MENU” appears. Use and key or and key to shift “>” mark to the left
shift “>” mark to the left of “Out Going” and press ENTER. of “(1) Bi-D Adjust” and press ENTER.
11. LX-300+: On the next screen, you can input the number of printing columns per
one movement of the carriage. Since the carriage width of LX-300+ is 13. The printing mode select menu for Bi-D adjustment appears. Use and key to
80, select the printing mode and use and key to select Bi-D setting.
use and key to shift “>” mark to the left of “(1) 80 column” and Then press ENTER. If you press the SPACE bar, the fallowing printing pattern will
press ENTER. printed (Refer to Figure 5-2).
LX-1170: Not applicable. Go to step 12.
Adjustment Overview 93
LX-300+/1170 Revision C
14. The following printing pattern which shows each mode number and current Bi- 17. By changing the VRO value, adjust the Bi -D. Repeat step 14 to 17 until the value
D values will be printed. “A” becomes within the range below. Refer to Table 5-4, “Bi-D Adjustment Setting
Value,” on page 95 for appropriate Bi-D value.
W○d¤0
15. At step14, if you press the SPACE bar, the Bi-D pattern for the selected mode
will be printed. For example, if you select Mode 0= VRO 0, the pattern below
will be printed.
W○d¤1&4
16. At step14, if you select Mode1=VRO 0 and press the SPACE bar, (1) Bi-D
printing patter will be printed. If Model 4=0, (2) will be printed.
(1)
(²) 0K
Adjustment Overview 94
LX-300+/1170 Revision C
Adjustment Overview 95
CHAP TE R
6
MAINTENANCE
Product Name Revision C
Use neutral detergent or diluted alcohol to clean the dirt on the outside. Vacuum dust or a 6-2 Teeth of Gears at the left frame G-26 1/2 grain of rice
small piece of papers inside the printer. 6-3 3 places on the 3 shafts of the right frame G-26 1 grain of rice
6-6 Paper guide from the back side at 4 places G-26 1 grain of rice
6-9 Touching parts of the 2 sides of the base frame. G-26 40mm x 2 places
Table 6-1. Lubricants NOTE: Lubrication must be applied during the re-assembly process.
Type Name Quantity Availability Part No. For lubrication points, refer to the following figures.
Maintenance Maintenance 97
Product Name Revision C
Spur
Spur Gear,
Gear, 13.2 Figure 6-3. Shafts at the Right Frame Assembly
13.2
RD ratchet
Maintenance Maintenance 98
Product Name Revision C
Set the paper guide assembly upside Figure 6-7. Tractor Assembly
down and lubricate at the touching part
Release shaft
of the PF roller assembly with the
Paper guide assy. release shaft. (4 places)
Paper guide assembly: The picture at the left is the back of the
G-26, 1 grain of rice Oil Pad printhead.
1. Set the oil dispenser 0.30ml.
2. Lubricate O-2 on the Oil pad.
Oil pad:
O-2, 0.28-0.32 cc
Note: Make sure that the setting of the oil
Figure 6-6. Paper Guide Assembly dispenser is correct.
Maintenance Maintenance 99
Product Name Revision C
Move the carriage around the center, Lubricate G-26 on the installing shaft of
then lubricate G-26 on the touching the Combination Gear, 17.5, 27 of the
parts of the 2 sides of the frame. right frame.
7
APPENDIX
LX-300+/1170 Revision C
CN3 HP Detector 2
CN7 PG Detector 2
CN9 Printhead 12
CN10 CR Motor 4
CN11 PF Motor 4
Table 7-4. Connector Pin Assignments - CN5 Table 7-8. Connector Pin Assignments - CN9
Pin I/O Signal Name Function Pin I/O Signal Name Function
7 - +5V +5VDC
8 - +5V +5VDC
Table 7-10. Connector Pin Assignments - CN11 Table 7-12. Connector Pin Assignments - CN13
Pin I/O Signal Name Function
Pin I/O Signal Name Function
6 O LED1 LED1
1 O PFA Paper feed motor phase A
7 I SW1 Switch 1
2 O PFA Paper feed motor phase A
8 - GND Signal ground
3 O PFB Paper feed motor phase B
9 - GND Signal ground
4 O PFB Paper feed motor phase B
10 I SW2 Switch 2
Table 7-11. Connector Pin Assignments - CN12 11 I SW3 Switch 3
Pin I/O Signal Name Function 12 I SW4 Switch 4
1 - VH +35VDC
2 - CS/HOLD +5VDC
3 - +5V +5VDC
8 - GP Signal ground
1 - +5V +5VDC
2 O LED5 LED5
3 O LED4 LED4
4 O LED3 LED3
5 O LED2 LED2
7.2 EEPROM Address Map Table 7-13. EEPROM Address Map (continued)
QPIT Factory
Address Explanation Setting
This section provides the EEPROM address map. Settings Settings
Area1
NOTE: The data of two or more byte are assigned as lower byte to lower address
and higher byte to higher address. 0: PC43721: Code MJK
*1: The data are fixed by each printer hardware in the factory. The data 1: PC85022: Bulgaria
should not be changed afterwards. 2: PC86023: Estonia
3: PC86324: PC774
Table 7-13. EEPROM Address Map 4: PC86525: IC8859-2
5: PC86126: PC866LAT
QPIT Factory
Address Explanation Setting 6: BRASCII27: PC866UKR
Settings Settings
7: Abicomp28: Hebrew 7
Area 0
8: ISO Latin 129: Hebrew 8
00H- 9: Roman 830: PC862
Reserved 00H 00H
03H 10: PC437Greek 31: PCAPTEC
Table 7-13. EEPROM Address Map (continued)Table 7-13. EEPROM Address Map (continued)
QPIT Factory QPIT Factory
Address Explanation Setting Address Explanation Setting
Settings Settings Settings Settings
26H,27 Reserved 3AH,
0000H 0000H Reserved 0000H 0000H
H 3BH
36H,
Reserved 0000H 0000H
37H
Table 7-13. EEPROM Address Map (continued)Table 7-13. EEPROM Address Map (continued)
QPIT Factory QPIT Factory
Address Explanation Setting Address Explanation Setting
Settings Settings Settings Settings
Software b0: Software 3 to 30 (by 0.1 sec.), 00H: 3 sec. 00H 00H
4DH Tear-off wait time
(0:ESC/P 1:IBM 2381 Plus) (same as default) (3 sec.) (3 sec.)
0 slash b1: 0 slash (0: off1: on) -432 to +432 (-25.4mm(-1inch) to
Buzzer 4EH, Tear-off adjustment
b2: Buzzer (0: on 1:off) 0mm +25.4mm (inch), by 0000H 0000H
4FH value
---- b3: Reserved 0.0588mm (1/432 inch))
45H 00H 00H
Auto CR b4: Auto CR(IBM) (0: off1:
on) 0: 19200 bps
Table 7-13. EEPROM Address Map (continued)Table 7-13. EEPROM Address Map (continued)
QPIT Factory QPIT Factory
Address Explanation Setting Address Explanation Setting
Settings Settings Settings Settings
57H Reserved 00H 00H 0: Table2
6DH IBM character table 00H 00H
1: Table1
Refer to Appendix E. I/F timing
58H *ACK timing data 00H 01H
data 0: Table2
6DH IBM character table 00H 00H
*ACK timing data 1: Table1
59H (complement of 00H 00H 6EH Fatal Error 00H 00H
58H)
0: 80 columns
5AH, 6FH Printable column 01H 01H
Reserved 0000H 0000H 1: 136 columns
5BH
Area 3
-144 to -72, 0: -72 (4.2mm)
5CH, TOF Minimum
When it is bigger than -72, the 00H 00H Vp adjustment
5DH value 70H *1 *1
value is considered as -72. value
Component layouts for each electric circuit board are shown as follows.
C○mp○n¤nt ‘id¤ ‘○ld¤r¤d ‘id¤
C294PNL BOARD
180
109
570 105
124
127
111
451 127(126/for EAI)
128 127
127 127
128
127 127
127 127
127
115
127
103 127
190 450
320 300
200
123
118
132
127
117
132
120
125
116
129
100 131
106
400
102
117
401
320 400
200
102
LX-300+No.01 Rev.0110202
Figure 7-7. LX-300+ Exploded Diagram 1
554
512
544 510
528 555
558
520
577
501
651
518 529
530
524
543 650
559
579
517 539 535
514 545
576 502
537 540 571
531 581
536 567
563
538 534 542 566
565
533
532
562
561 506 531 590
564 559
559
503 569
575
560 568 514
574
578511
515
581
581
580
573
504
581
581 581
LX-300+No.02 Rev.0110202
547
105 550 180
107
519
109
550
550
549
550
119
119
300 200
119
128
119
126
111
451 119 128 119
119 119
100
129 400
401 400
500 130
119
539 529
592 535
514
538
543
571
502
559 569
514
651 568 564
511 515
560 503
124 "SHEET,PROTECT,L"
126 "SHEET,PROTECT,R"
129 "C.B.B-TITE(P(13)),3X14,F/ZN"
180 "GUIDE,STACKER"
552 "FRAME,TR,RIGHT"
553 "FRAME,TR,LEFT"
554 "TRACTOR,LEFT"
555 "TRACTOR,RIGHT"
556 "SHAFT,TR,DRIVE"
557 "SHAFT,TR,GUIDE"
559 DAMPER
560 "FRAME,BASE"
563 "SHEET,CABLE,HEAD"
564 "GEAR,34"
569 "HARNESS,RELEASE"