003
Sign
Name
Date
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 1/7
1. TUJUAN 1. OBJECTIVE
Memberikan panduan dan standar pekerjaan Provide guidance and standard of work to be
yang harus dilakukan saat melakukan inspeksi performed when conducting inspection and testing
dan pengujian terhadap semua relay proteksi of all protective relays with all devices contained
dengan segala perangkat yang terdapat therein already installed in production by the
didalamnya yang telah dipasang dipanel oleh manufacturer in accordance with the specifications
produksi sesuai dengan spesifikasi yang telah specified in the drawings so that it can be
ditetapkan dalam gambar sehingga dapat ascertained that meet the requirements /
dipastikan yang memenuhi persyaratan / specifications that have been set customer.
spesikasi yang telah ditetapkan pelanggan.
2. SCOPE
2. RUANG LINGKUP
This procedure defines the things that must be
Prosedur ini mendefinisikan hal-hal yang harus
done when performing inspection work and testing
dilakukan saat melakukan pekerjaan inspeksi
of protection relays that have been installed by the
dan pengujian relay proteksi yang telah
production in PT MIM both Local and Import, from
dipasang oleh pihak produksi di PT MIM baik
the beginning of inspection and testing to be sent
yang Lokal maupun Import, dari awal inspeksi
according to the drawings and specifications.
dan pengujian hingga dapat dikirim sesuai
gambar dan spesifikasinya.
3. PROSEDURE 3. PROCEDURE
3.1 Pengecekan Fisik 3.1 Physical Checking
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 2/7
3.2 Pengujian Electrical 3.2 Electrical Testing
1. Perform isolation-resistance tests on each
1. Lakukan isolasi-tes hambatan pada
circuit to the frame / chassis, as specified
setiap rangkaian ke bingkai / casis,
from the manufacturer's published
sesuai yang ditentukan dari data
procedure data which is permitted to test
prosedur yang diterbitkan produsen
the type of solid-state and / or
yang diizinkan untuk test jenis solid-
microprocessor-based relay if there is an
state dan atau relay berbasis
application.
mikroprosesor jika ada aplikasinya.
2. Determine all the required input parameters
2. Menentukan semua parameter input
of the relay.
yang dibutuhkan relay.
a. Specify the sensing mode for the current.
a. Tentukan mode sensing untuk arus.
b. Determine the Phase and / or Ground
b. Tentukan parameter Phase dan atau
Current parameters.
Ground Current.
c. Determine the voltage sensing mode.
c. Tentukan mode sensing tegangan.
d. Determine the sensing ratio transformer.
d. Tentukan transformer rasio sensing.
e. Determine the phase parameter and / or
e. Tentukan parameter phase dan atau
the neutral potential of the transformer
netral potensial transformer rasio
sensing ratio (fundamental voltage) if
sensing (tegangan fundamental) jika
there is an application.
ada apliksinya.
f. Determine Frequency sensing /
f. Tentukan Frekuensi sensing /
operation.
operasional.
g. Determine the temperature sensing type.
g. Tentukan jenis sensing temperatur.
3. Checking targets and indicators.
3. Memeriksa target dan indikator.
a. Determine the pickup and reset of the
a. Tentukan pickup dan reset dari
protective relay target.
target relay proteksi.
b. Verify all diode light / led indicator
b. Memverifikasi semua operasi dioda
operation.
cahaya / led indikator.
c. Set contrast for the layer if there is an
c. Atur kontras untuk layer jika ada
application.
aplikasinya.
3.3 Functional Operation Protection
3.3 Operasi Fungsional Proteksi
All relay tests shall be guided by the guidebooks
Semua pengujian relay harus berpedoman
already issued by the manufacturer in accordance
pada buku panduan yang telah diterbitkan
with the goods. The general method is as follows:
oleh produsen yang sesuai dengan
barangnya. Adapun secara umum
metodenya adalah sebagai berikut:
1. 2/62 Relay Timing
1. 2 / 62 Timing Relay
a. Determine the delay time.
a. Tentukan waktu tunda.
b. Immediate operational verification of contacts
b. Verifikasi sesaat operasional dari
(opening and closing times).
kontak (waktu buka dan tutup).
2. 21 Relay Jarak
2. 21 Distance Relay
a. Tentukan jangkauan maksimum.
a. Specify the maximum range.
b. Tentukan sudut torsi maksimum.
b. Determine the maximum torque angle.
c. Tentukan offset.
c. Determine offset.
d. Plot impedansi lingkaran.
d. Plot the circle impedance.
3. 24 Volts / Hertz Relay
3. 24 Volts / Hertz Relay
a. Tentukan nilai pickup pada tegangan
a. Determine the pickup value at the frequency
frekuensi.
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 3/7
b. Tentukan frekuensi pickup pada level b. Determine the pickup frequency at the second
tegangan kedua. voltage level.
c. Tentukan waktu tunda. c. Determine the delay time.
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 4/7
9. 46N Negative Sequence Rrelay 9. 46N Negative Sequence Rrelay
a. Tentukan negative sequence batas a. Determine the negative sequence of the alarm
alarm. limit.
b. Tentukan negative sequence batas b. Determine the minimum negative sequence
minimum trip. minimum trip.
c. Tentukan maksimum waktu tunda. c. Specify maximum delay time.
d. Verifikasi dua titik pada (h) 2 t kurva d. Verify two points on (h) 2 t curves
10. 47 Phase Sequence atau Voltage 10. 47 Phase Sequence or Voltage Balance Relay
Balance Relay a. Determine the positive sequence voltage to
a. Tentukan tegangan urutan positif close the normally open contacts.
untuk menutup kontak yang normal b. Determine the positive sequence voltage to
terbuka. open the normally closed contact
b. Tentukan tegangan urutan positif (undervoltage).
untuk membuka kontak normal
tertutup (undervoltage).
c. Memverifikasi urutan negative trip c. Verify negative trip sequence
d. Tentukan waktu tunda untuk d. Determine the delay time to close normally
menutup kontak normal terbuka open contacts with a sudden application of
dengan tiba-tiba aplikasi dari 120 120 percent of the pickup.
persen dari pickup.
e. Tentukan waktu tunda untuk e. Determine the delay time to close the
menutup kontak normal tertutup normal closed contact on the removal
pada tegangan penghapusan ketika voltage when it was previously set to the
sebelumnya diatur ke sistem nilai system voltage value
tegangan
11. 49R Replika Thermal / Overload Relay 11. 49R Thermal Replika / Overload Relay
a. Tentukan waktu tunda pada 300 a. Determine the delay time at 300 percent of the
persen dari pengaturan. settings.
b. Tentukan kedua titik pada kurva b. Determine both points on the operating curve.
operasi. c. Specify pickup.
c. Tentukan pickup.
12. 49T Suhu (RTD) Relay. 12. 49T Temperature (RTD) Relay.
a. Menentukan trip resistansi. a. Determine trip resistance.
b. Tentukan reset resistansi. b. Determine reset resistance.
16. 59 Overvoltage/ Tegangan Lebih Relay 16. 59 Overvoltage / Voltage More Relays
a. Tentukan pickup tegangan lebih. a. Specify more voltage pickup.
b. Tentukan waktu tunda untuk b. Set the delay time to
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 5/7
menutup kontak dengan aplikasi close contact with the app suddenly 120 percent of
tiba-tiba 120 persen dari pickup. the pickup.
20. 67 Directional Kelebihan Arus Relay 20. 67 Directional Overload of Relay Current
a. Menentukan arah pickup minimum a. Determine minimum pickup direction of the unit
unit di sudut torsi maksimum. at maximum torque angle.
b. Tentukan zona penutupan b. Define the closing zone
c. Tentukan maksimum torsi sudut c. Determine maximum angular torque
d. Plot karakteristik operasi d. Plot the operating characteristics
e. Tentukan unit kelebihan arus pickup e. Determine the overcurrent unit of the pickup
f. Tentukan kelebihan arus f. Determine the excess current determines the
menentukan satuan waktu tunda di time unit delay at two points on the time-flow
dua titik pada kurva arus waktu. curve.
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 6/7
24. 87 Differential 24. 87 Differential
a. Tentukan unit operasi pickup. a. Determine the pickup operation unit.
b. Tentukan operasi pengendalian dari b. Determine the control operations of each
masing-masing unit. unit.
c. Tentukan lereng / slope. c. Determine the slope / slope.
d. Menentukan harmonik menahan diri d. Determining harmonic restraint does not trip
tidak trip / harmonic restrain. / harmonic restrain.
e. Tentukan seketika pickup. e. Determine the pickup instantly.
f. Karakteristik operasi plot untuk f. Characteristics of plot operations for each
masing-masing menahan diri tidak refrain are not trip.
trip.
5. Dokumet Terkait
1. IK.QC.E.007_General Inspection Of Panel
2. F.QC.E.001_Verification Of Protection Relay
Procedure Title: Pengujian Relay Proteksi Doc No: PRO.QC.E.003, Rev.0 Page: 7/7