PEKERJAAN :
PENGADAAN SPEED BOAT MALUKU
DAN MALUKU UTARA
POKJA :
TAHUN ANGGARAN :
2016
Kepada Yth.:
Pokja : Pengadaan Barang (BPJN IX)
ULP Wilayah Maluku
di-
Ambon
Perihal : Penawaran Pekerjaan Pengadaan Speed Boat Maluku dan Maluku Utara
Penawaran ini sudah memperhatikan ketentuan dan persyaratan yang tercantum dalam
Dokumen Pengadaan untuk melaksanakan pekerjaan tersebut.
Penawaran ini berlaku sejak batas akhir pemasukan dokumen penawaran sampai dengan
tanggal 06 Maret 2016.
Dengan disampaikannya Surat Penawaran ini, maka kami menyatakan sanggup dan akan
tunduk pada semua ketentuan yang tercantum dalam Dokumen Pengadaan.
REKAPITULASI
JUMLAH HARGA
NO URAIAN PEKERJAAN
( Rp )
A PEKERJAAN KONSTRUKSI LAMBUNG KAPAL 828.750.000,00
D MOBILISASI 70.687.500,00
Terbilang : Tiga Milyar Delapan Ratus Lima Puluh Juta Tiga Ratus Dua Puluh Lima Ribu Rupiah
HARI
NO URAIAN PEKERJAAN KET
1-45 46-75 76-100 100-130 131-150 151'175 175-200 200-210
1 Persiapan Pekerjaan :
- Desain Rencana Garis
- Desain Rencana Umum
- Desain Penampang Melintang
2 Pekerjaan Kapal :
- Pembuatan Cetakan
3 Laminasi Bodi Kapal :
- Laminasi Lambung Kapal
- Pembuatan Sekat-Sekat
4 Out Fitting :
- Pemasangan dan Laminasi sekat - sekat
5 Pemasangan Perlengkapan Geladak :
- Pemasangan tutup Palka
6 Pemasangan Sistim dan Mesin :
- Pemasangan Pondasi Mesin
7 Finishing :
- Pengecatan
8 Uji Coba :
- Peluncuran
- Dok. Trial
- Sea Trial
9 Order Barang (Perlengkapan Kapal)
10 Pengepakan dan Pengiriman Barang
11 Pemeriksaan Barang
12 Penyerahan barang ke tempat akhir
210 HARI
JUMLAH WAKTU PELAKSANAAN
KALENDE
R
Speed Boat ini digerakkan oleh mesin jenis Outboard Marine Engine dengan jumlah 2 ( dua ) Unit,
yang dilengkapi juga dengan bilge pump dan lain-lain untuk beroperasi di daerah perairan pantai.
Lambung kapal direncanakan berbentuk hard chine lambung tunggal yang didesain secara khusus agar Speed
Boat ini bisa berlabuh di bibir pantai ( Beaching ) dengan menggunakan sarana trolly.
Lambung ( Hull ) Crew Boat dibuat dari bahan Fiberglass Reinforced Plastic ( FRP ) Type multiaxial, dimana
bahan tersebut mempunyai kelebihan diantaranya; relative murah, ringan, serta mempunyai kekuatan yang
cukup layak menurut peraturan klasifikasi terutama untuk kapal-kapal heavy duty.
Gambaran Umum
Kapal menggunakan konstruksi lambung tunggal (single hull) dengan; Geladak utama menyatu
untuk penumpang serta geladak navigasi untuk ruang kemudi. Speed digerakkan oleh 2 ( dua ) buah mesin
induk dengan jenis Outboard Marine Engine (4-stroke atau mesin yang sudah terstandar gas buang Euro-3).
sedangkan untuk proses pembangunannya, kapal dibangun dengan material utama dari bahan Fibre
Reinforce Plastic (FRP) multi axial dengan lapisan gelcoat pada layer terluar.
UKURAN UTAMA
Ukuran Pokok Speed / Crew Boat :
Panjang Seluruhnya ( LoA ) : 12.00 meter
Lebar ( B ) : 3.00 meter
Tinggi ( H ) : 1.65 meter
Sarat air (T ) : 0,60 meter
Mesin ( Engine ) : 2 x 250 Hp ( OBM 4 stroke atau mesin yg sudah mempunyai
standar gas buang Euro-3 )
Pembagian Ruangan
a) Ruang Buritan
Ruang buritan terletak dibawah geladak navigasi. Ruangan ini digunakan untuk: Tangki bahan bakar
dengan kapasitas minimal 800 liter.
b) Ruang Navigasi
Ruang kabin kemudi terletak di ruang navigasi yang di pergunakan untuk keperluan navigasi kapal yang
dilengkapi dengan peralatan penunjang navigasi sebagaimana tercantum dalam daftar peralatan
navigasi.
Material
Konstruksi lambung, geladak, dan kabin dibuat dari bahan fiberglass yang dicetak menggunakan
system hand lay-up atau spry lay-up. Pada permukaan luar merupakan lapisan gelcoat yang dicampur
dengan pigment warna, sekaligus berfungsi untuk lebih meningkatkan kekedapan kapal.
Untuk bahan baku FRP pada konstruksi kapal, bahan perekat yang digunakan adalah resin polyester untuk
marine yang umum dignakan untuk pembuatan kapal, dikombinasikan dengan lapisan chopped strand mat
(CSM), yang dikombinasikan dengan kain glass fibre multiaxial/multiaxial fabric (generasi ke-tiga dari WR) :
Keel
12 lapis : 5 x CSM 450
: 7 x DB 830
Bottom
8 lapis : 4 x CSM 450
: 4 x TDB 830
Side Shell
7 lapis : 3 x CSM 450
: 4 x TDB 830
Main Deck
6 lapis : 2 x CSM 450
: 4 x TDB 830
Keterangan :
Keterangan schedule laminasi diatas belum termasuk gelcoat yang wajib tambahkan di
semua lapisan luar dengan tambahan pigmen warna
GC : Gelcoat 400 gr/m2
CSM 450 : Chopped Strand Matt 450 gr/m2
TDB 830 : Tensile Biaxial Fabric 800 gr/m2
Tipe dempul yang digunakan untuk daerah yg berhubungan langsung dengan cuaca luar
adalah Dempul aerosil : Dempul campuran resin dengan tepung aerosil
Lambung
Lambung pada kapal ini adalah lambung sisi ganda guna menambah kekuatan memanjang kapal
serta mengurangi resiko kebocoran, dan juga untuk menambah performa stabilitas kapal (safety buoyancy).
Konstruksi lambung kapal diperkuat dengan penguat-penguat melintang (Frame) dan memanjang kapal
(stringer). Pada bagian bottom dipasang wrang dan side girder serta pada bagian sisinya dipasang side
longitudinal.
Lantai
Lantai speed menggunakan system menyatu sebagai satu kesatuan konstruksi kapal berbahan FRP
yang dicetak dengan perencanaan ketebalan mengacu pada standar klas dari Biro Klasifikasi Indonesia.
Geladak luar pada bagian sisi kapal dilapisi dengan karet anti selip.
Pondasi Mesin
Mesin pada kapal ini menggunakan jenis out board untuk menunjang pencapaian kecepatan kapal
yang telah ditetapkan sehingga pondasi mesin harus dirancang berdasarkan perhitungan kekuatan dorongan
mesin maksimum dan Mesin diikat dengan baut tahan karat.
PERLENGKAPAN KAPAL
a. PERMESINAN DAN INSTALASI :
Mesin Tempel / Marine Engine 250 HP :2 unit
Filter Bahan Bakar :2 Set
Fuel Indicator Mesin :2 Set
b. PERLENGKAPAN KAPAL :
Remote Kontrol + Cable 15 M :2 set
Sterring hydrolic Kemudi lengkap :1 unit
Steer / Kemudi Outomat :1 Bh
c. PERLENGKAPAN LISTRIK :
Lampu Cabin :1 Set
Lampu Navigasi Merah – Hijau :1 Set
Lampu Sorot :1 Set
Lampu Tiang / Lampu Jangkar :1 Bh
Bilga Pump / Pompa Celup :1 Set
Pannel Saklar :1 Set
Baterray Switch :1 Bh
Generator Set Marine 5000 Watt :1 Bh
Accu (Battery) 12 Volt 150 AH :2 Bh
e. ALAT KESELAMATAN :
Life Jacket : 28 Bh
Life Bouy :2 Bh
Kotak P3K + Obat - Obatan :1 Set
Pemadam Kebakaran Uk. 2,5 Kg :2 Unit
f. PERLENGKAPAN TAMBAT :
Relling Haluan Pipa ss 304 dia 1” :1 Set
Hand Ralling pipa ss 304 dia 1” :2 Set
Tiang Bendera Pipa dia 1” :1 Bh
Cleat SS/ Pengikat Tali 8 “ :4 Set
Fender Fiberglass :1 Set
Jangkar 15 Kg :1 Bh
Tali Jangkar 12 mm : 50 Mtr
Tali tambat 12 mm X 20 m X 2 : 40 Mtr
g. PERLENGKAPAN KAPAL :
Kursi Kemudi :1 buah
Kursi Penumpang : 16 buah
Sofa :2 buah
Meja :1 buah
Marine Toilet + Wastafel :1 set
System Pengisian Bahan Bakar :1 set
System Pipa Udara Bahan Bakar :1 set
System Pengisian Air Tawar :1 set
Jendela Geser ( Kaca Akrilik 5 mm ) :4 set
Jendela Mati Depan ( Kaca Akrilik 5 mm ) :2 set
Showerr :1 buah
Kompor Gas 1 Lobang + Selang Regulator :1 set
Tabung Gas Fortable 3 Kg :1 buah
Dispenser + gallon Air :1 set
Piring, Gelas, Sendiok, Garpu masing2 1 lusin :1 Set
Gantungan Baju :1 Unit
Tempat Tidur, Bantal Guling + Sprey :1 Set
TV LCD 40 “ DVD Player + Handy Cam :1 Set
Tangki BBM Stailessteel 304, 2 mm Cap 700Ltr :1 set
Tangki Air Tawar Cap 300 ltr ( FRP ) :1 set
AC 2 PK :1 Set
AC 1/5 PK :1 Set
HAND RAIL
Railling kapal dibuat dari bahan stainless steel yang dipasang pada bagian Haluan kapal untuk
menambah keamanan dan keselamatan awak kapal maupun penumpang.
HORN
Peralatan kapal ini dipasang diatas ruang kemudi sebagai salah sarana pembantu navigasi kapal
sekaligus sebagai Public Addresor.
SISTEM PERMESINAN
Permesinan Utama
Mesin penggerak utama terletak di buritan kapal dengan spesifikasi jenis :
Jumlah mesin : 2 unit, outboat marine engine
Daya Mesin (Minimal) : 2 x 250 HP
Tipe Mesin : Outboard Marine Engine 4 stroke atau mesin dengan standar emisi
gas buang Euro-3.
Starting : Electric
Ignition : TCI Microcomputer
Bahan bakar : Regular Unleaded ( Minimum pump octane 87 )
Sistem pendingin : Water/Thermostic control
KELISTRIKAN
System kelistrikan kapal menggunakan battery DC 12 V 150 AH, dengan alternator pada mesin
induk untuk keperluan charging.
LAIN-LAIN
Klasifikasi dan Sertifikasi
Konstruksi kapal yang akan dibangun mengikuti peraturan klasifikasi dari Biro Klasifikasi Indonesia
(BKI) Fiberglass 1996 walaupun konstruksi kapal tidak di klass kan, dan peraturan dari pemerintah Indonesia
yang terkait.
DOKUMEN KAPAL
Dokumen kapal yang harus disertakan oleh pembangun kapal saat penyerahan kapal mengacu
pada dokumen standar sebagai berikut :
1. Rencana Umum ( Arragement )
2. Rencana Garis ( Lines Plan )
3. Konstruksi kapal (Melintang, dan Memanjang)
4. Konstruksi Profile Geladak dan Dasar/ Bottom
5. Buku panduan mesin / Manual Book
PENGUJIAN
Semua instalasi harus diuji dan dicoba sesuai dengan program yang telah disetujui untuk
membuktikan bahwa instalasi tersebut memenuhi spesifikasi yang ditetapkan dan sesuai dengan fungsi yang
direncanakan.
Menjelang tahap penyelesaian, pembangunan kapal, pihak galangan / penjual melaksanakan official sea
trial yang mencakup pengujian dan percobaan antara lain :
Dokumen kapal yang harus disertakan oleh pembangun kapal saat penyerahan kapal mengacu pada
dokumen standar sebagai berikut :
1. Dokumen dan gambar teknis final (as build drawing)
2. Foto bertahap selama proses pembangunan
3. Foto dan video hasil sea trial
4. Buku panduan mesin kapal.
Perusahaan kami adalah distributor untuk materia pembuatan kapal fiberglass yang meliputi :
- Resin Everpol324AR-@ dan Gecoat 3610R
- CSM 300 dan 450 gr/M2
- WR600 dan 800gr/M2
Bersama surat ini memberi Dukungan sepenuhnya untuk ketersediaan barang tersebut di atas kepada :
Untuk mengikuti pelalangan/tenderl yang dilaksanakan oleh Pokja Pengadaan Barang Balai Jalan Nasional IX
(Maluku dan Maluku Utara) Pekerjaan Pengadaan Speed Boat Maluku dan Maluku Utara tahun Anggaran 2016.
Demikian Surat Dukungan ini kami buat dengan sebenarnya untuk dipergunakan oleh CV. DAMAS JAYA dalam
proses tender dimaksud, dengan syarat : Surat Dukkungan ini menjadi Batal apabila CV. DAMAS JAYA ternyata
menggunakan produk lain.
Fiberglass Reinforced
Plasti c Products
CATALOC U E
SOLCTIHM@
'Innovation eornes first'
PT Solchem is a subsidiary of PT Arindo Pacific Chemicals has Wisma Bumiputera 1Oth Floor
become one of the leading resin trading company in Indone- Jl. Jend. Sudirman Kav.75, Jakarta 12910 - Indonesia
sia. Since the beginning, it has been the policy of the company Phone : +62 21 5710864 (Hunting)
to be focused more on the high end products that can bring Fax : +62 21 5712318
more value added to the customers. lt is also central to the Email :support@ptsolchem.com
company's philosophy to have strategic cooperation with both
Website : www.apc.co. id
our suppliers and customers, so that we can best serve their
needs.
FACTORY
MISSION : "We put innovation at the heart of
PT. Solchem in the way we think and act"
Jl. Mercedez Benz No.244
Cn. Putri Bogor 16965, lndonesia
PHILOSOPHY : "We deal honestly with our customers, to Phone : +62 21 8672928 (Hunting)
build a long Iasting business relationships" Fax : +62 21 8670771
The lndustries We Serve
Marine Plywood Transport SERVICE ASSISTANCE :
Building Construction Pipes and re-lining General lndustry Phone : +62 21 86860655
Button
We expert in a range of processing technique OUR REPRESENTATIVES:
.1.
Brush / Spray 1. Bandung 4. Semarang
2. RTM 2. Medan 5. Banjarmasin
3. Vacuum lnfusion 3. Surabaya
p. oz I pr. sor cHFM
F=- ,r:L-/
-
IYi:]'Tit{,}t,#i
ttilt{tr. iti}.
Miscellaneous ltem 14
e ol I pt.soLCHFM
Materials used to assist the catalyst in the drying process
polyester and vinyl ester resin at room temperature.
Cobalt N 8%
Cobalt O B"/o
Honey wax @ 250 leaving the a smooth surface, hard and shiny'
Packaging z 11 oz (3129)/Can,
12 Cans /Box
p. oe I pr. soLCHEM
Kantstik@ C is a polyvinyl alcohol/water based mold release that is clear in color. Kantstik@ C is typically used in
conjunction with another release agenl to provide absolute positive release, especially on new unseasoned molds made
with polyester resins. Kantstik@ C can also be sprayed over polyester Gelcoat or resin used for repair purposed, allowing
the surface to tack free.
Packaging: 1 gallon bottle, 5 gallon pail, 55 gallon drum
Buffaway rM 1000
is our best compound for removal of 600 grit scratches, heavy orange peel and oxidation from polyester tooling and
production Gelcoats. Designed for use with 2400 rpm rotary buffers and wool buffing pads, BuffAwayrM 1000 features
excellent cutting properties, high gloss, and water based formula that gets the iob done with half the product and time
required by traditional cutting compounds.
Euffaway rM 2OO0 is an outstanding polish for the ultimate in surface perfection and gloss. Designed for use with 2400 rpm
rotary buffers and wool or synthetic polishing pads, BuffAw"yTM 2OOO easily removes minor scratches and swirl marks for
a mirror finish on polyester production and tooling Gelcoats. Plus, its water based formula gets the job done with half the
producl and time required by traditional polishes.
Fackaging:2 gallon pail, 5 gallon pail, 55 gallon drum
Gelcoat
Celcoat is a base Polyester Resin orVinyl Ester Resin, a thin layer of FRP
surfaces that are resistant to weather, chemicals and heat. FRP products
are smooth, gloss and good mechanical strength.
CIear Celcoat
- Everpol 3611 R (Ortho Crade)
- Everpol 3610 R (lso Crade, LR Registered)
Color Gelcoat
- White Celcoat, Everpol 3610 Snow White (Spray)
- White Celcoat, Everpol 3610 Snow White (Brush)
- Black Gelcoat, Everpol 3610 Super Black (Spray)
- Black Gelcoat, Everpol 3610 Super BIack (Brush)
- Customize (Red, Blue, Yellow and etc)
Tooling Gelcoat (Vinyl Ester based)
- Everpol 362 T (Black & Red Color)
p az I pr. soLCHEM
Reinforcing material made of strands fiber glass is cut
about 1 inch and tied with polyester powder or emulsion
binder.
Characteristics :
Consistent quality, thickness and rigidity
Easily wetted resin & easily remove air trubbles
Cood mechanical ProPerties
C-Class type for manufacture of CRP pipes, storage tank, Reinforcing material is commonly called the statute fiber
CRP lining or in hand lay-up for improving surface of glass Roving Cloth wovened from roving continuous' Used
Packaging of
lissue Mat/Surfacing Veil : Type of Woven Roving : Packaging:
30 Cr/M2, Width 1 M, EWR 600 (Width 1 m) Net Weight 40 & 50 Kgs/
300 M/Roll EWR 800 (Width 1.24 m) Carton
p. ol I pr. soLCHEM
Reinforcing material, is Fiber Class type with a little use binder
(<1% binder) or almost no use of binders, resin has a Bood absorption,
high mechanical strength and efficient resin.
Multiaxial is a continuous roving are stitched or Combination Roving's
with Mat stitched together.
Drying material used to start the polymerization process of the polyester or vinyl
ester resin from AKPA CHIMICALS (Turkey)
Akperox 42 Ceneral purpose MEKP for curing unsaturated polyester (UP)
resins & vinyl ester resins at room temperature.
Cenerally used together with metal salts as accelerators.
Akperox 460 Ceneral purpose MEKP for curing unsaturated polyester (UP)
resins & vinyl ester resins at room and high temperatures.
Akperox A60G Special MEKP for curing Celcoat Resins at room tempera
ture. Low water content and bring high gloss surface area.
Akperox A6R Phthalate Free type MEKP. lt's used for curing of UP resins at
room and high temperature.
Recommended to be used during production of composite
materials which directly get in contact with human body
such as button, water tank etc in point of Phthalate Free
l:.:j=
specialty. L::==
Akperox ER60 tW MEKP for curing UP resins at room and high temperatures.
Particularly suitable for pipe production and continuous
manufacturing applications such as continuous lamination,
RTM, filament winding & centrifugal casting.
e as I pr soLCHEM
General Purposes (Boat, \dater Tank, Automotive arrd etc)
- Everpol 324 AR- 2 (Thixotropic)
- Everpol C 405 EPA- 1 (Thixotropic)
- Everpol 325 AL (Non Thixotropic)
Putty
- Everpol 380
Packaging : NetWeight22S Kgs/Drum
Pipe Lining
EVERPOL 324VE-P benefits include tow foaming characteristics, high tensile elongation and flexibility for
manipulating the production Iine speeds while producing pipes by continuous and helical filament winding
process.
Skin Coat
EVERPOL 324 VE-SC has excellent blister resistance and significantly reduces the occurrence of print through, to
produce durable moldings with an enhanced surface finish.
Fireguard
Everpol 324 VE-FC gives outstanding fire protection to FRP laminates which are accidentally exposed to direct
flaming. lt is also suitable as a fire-retardant coating on wood and other slightly porous surfaces. However, due
to lack of adhesion after intumescences, it is not suitable for use on metals.
p. ot I pr.sorcHEM
1. A repositionable, high strength adhesive spray compatible
with Celcoat, barrier-coat, glass fiber matting and fiber glass
laminates.
2. Fully compatible with polyester and vinyl ester resins.
1
J. Does not compromise the mechanical performance of
laminates, even if used in higher quantities than actually
required.
4. Does not compromise or inhibit the correct polymerization
of resins.
5. Does not weaken the degree of interlaminar adhesion
between the different layers of a laminate.
6. Contains a blue colorant which makes it possible to assess
and regulate the quantity Aerofix 3
7. Applied, with the color disappearing during polymerization.
Packaging:
Aerofix 3 is available in aerosols (500m1 spray cans).
1. Perforated release film combined with knitted infusion A high strength, high elongation bagging film for low
mesh by gluing. temperature vacuum bagging Applications. A multilayer
2. This new system allows the material to be cut into co-extruded product with excellent resistance to polyester,
different widths and complex forms. The adhesive is vinyl ester and epoxy resins. VACFILM 400Y is available
spread over the entire surface. on large width and is ideal for use in the production of
3. This process offers many possible combinations wind energy structures and marine.
including drainage flow variables.
Note : VACFILM 400Y is not suitable for use in autoclave cure
cycles.
PHYSICAL PROPERTIES
lnfusion mesh Release film PHYSICAL PROPERTIES Method
INFUPLY2 = vil A.2200 Max. Use Temperature 150"C rso 3146
Material PE PE Color Yellow
Maximum use temperature 100"c - 120'c Elongation at break 4OOoh (*1ooh) ASTM D8B2
12A"C Tensile strength at break 40N/mm2 (t]0%) ASTM DBB2
Color Blue Orange Yield 509 : 19.08m2/kg lnternal
Weight 15O{m2 659 :14.66m2/kg
759 :12.90m2/kg,
Packaging : 50 m/Roll, Width 4.6 m
e og I .r. sorcurit,t
Economic low cost vacuum bag sealant tape. Excellent Porous nylon release fabric. Heat set and scoured. Can
tack. Ideally suited to debulking operations at ambient be used directly against larninates or bond lines. No need
to clean: surface where secondary bonding, painting or
temperatures and high temperature envelope bagging
finishing is required. lmparts a relatively .-orrc" *eiue
applications. Material compatible with most substrates pattern upon removal from the laminate. Release from
(including composite tools) and film materials. most commercial resin systems. Available with a red tracer
For optimum results, tape must be allowed to cool to line spaced every 30mm for ease of identification on the
ambient before stripping from mould surfaces. cured laminate. Due to natural affinity between phenols
and nylons this material is not recommended for use with
phenolic resin or prepreg or used at temperatures higher
PHYSICAT PROPERTITS
then 180"C.
Maximum Use Temperature 90"c
Color Black
PHYSICAT PROPERTIES
Solids 100% Material
Flammability Not flammable but PA
combustible Maximum Cure Temperature 1 BO"C
Treatment Heat set and scoured
Fabric Weight (nominal) BO{m2
PACKAGING:
Color White with red tracer
Roll size 3mm x 12mm x 15m
Release agent None
Standard box contents 22 rolls
PACKAGING:
Standard sizes 1.52m x l00m
TT
TS10 = 10mm OD.
PHYSICAL PROPERTIES
.l
Maximum temperature 60"C TS14 = 14mm OD.
Assembly widths 75 & 100 mm.
Total combination width =
Membrane width + 2x15 mm
Rolls 100m (Other dimensions on
request)
P lo I pr. sorcHru
lnfusion Flose & lnfusion Spiral
Hose'bring resin and vacuum from PE with the
temperature resistance up to 150oC
A22OO is a low cost, very ftexitrle release film which is ideal for resin infusion processing. Colored opaque orange to
allow resin front to be monitored during infusion plus aiding complete removal whilst de Bagging. Suitable for use with
epoxy, polyester and vinyl ester resins although we strongly advise that a test piece is produced prior to committing to a
full scale infusion in order to determine compatibility and performance meet desired standards.
PHYSICAL PROPERTIES
Value Method
Material PE
PACK'AGING:
Standard thickness 250
Standard perforation P31 (See details on the perforations
Standard widths 0.1m, 1.30m and 1.45m
Everpol 324 A-VlP is a ortho based polyester resin Everpol 324Va-l is a base vinyl ester resin designed for vacuum
designed for vacuum infusion system, promoted, non wax infusion system, promoted, non wax and non-thixotropic with
and non-thixotropic good heat resistance, weatherability, and mechanical strength
than Unsaturated Polyester Resin {UPR).
Properties: Properties :
p tt I n.soLCHEM
Styrene is used to make various copolymers used in coatings, adhesives,
elastomers, and materials structural. Most of the styrene monomer substitu-
tion allows the incorporation of specific functional groups to in the polymer,
Styrene is unique because it is one of the few monomers which undergo fb-''"* ^--.<:
Ji-:
-
polymerizationwith the mechanism radical, cationic, or anionic.Styrene, iG!""=" >e-,rr"".ru
also known as vinyl benzene and phenyl ethane, an organic compound with
chemical formula C6H5CH=CH2.
Styrene is a precursor and a copolymer of polystyrene. To the field of FRP
is used as a solvent for the manufacture of resins polyester and vinyl
ester resin and as a diluents.
Packaging :
p tz I n.soLCHEM
FRP Scissors are special scissorsfor cutting FRP glass fiber,
carbon fiber and Kevlar reinforcemenl from Sheffield
England. Very simple, easy for cutting for more large
th i ckness
Type:
Kevlar/Aramid Shear 1 0"
Class Fibre Shear 10"
Carbon Fiber 10"
Technical Features:
Blade Diameter 70 mm with carbide counter blade
Blade Speed 750 revolutions/min
Cutting working depth 20 mm circa
Weight with package 2000 g
Electrical cable length 1,5 meter
Temperature 0 - 550C
Humidity 10' 95% without condensate
p. ts I pr. soLCHEM
WEST & SENIOR LIMITED have manufactured liquid,
powder & paste dispersions for both Pigments and
additives for over 50 years. h.'iagooiia Ivor1.. Pale Cleen ir,la*illa frea*r
1 KgiTin # t
5 KgslTin
Br'i-sht Bhre h{Lrli}{tay Blus French Blue Treffic Blue Oxfor'd Blue
25 Kgs/Pail - -
ffiffi ffi
l{i;rlor* Ler:rol G..ldea Yelltu T:lgerine Brilliml Recl
r. tt I n.soLCHEM
SURAT DUKUNGAN DISTRIBUTOR
Nomor : 010/ YWL-SD/I/2016
Sehubungan dengan penyediaan GPS pada Pelaksanaan pelelangan pekerjaan Pengadaan SPPED BOAT
MALUKU DAN MALUKU UTARA yang dilaksanakan oleh Pokja Pengadaan Barang Balai Jalan Nasional IX
(Maluku dan Maluku Utara) di Ambon Tahun Anggaran 2016.
Surat dukungan ini dikeluarkan untuk produk yang kami jual/tawarkan, dan kami menjamin bahwa
barang/produk dimaksud adalah telah memenuhi persyaratan spesifikasi teknis dalam dokumen
pengadaan.
Surat Dukungan Pengadaan ini BATAL dengan sendirinya dan tidak berlaku lagi apabila :
1. Yang diberi dukungan mendapat pesanan tersebut diatas, tetapi kemudian menyerahkan/
menjual barang/kendaraan bukan dari dealer/distributor kami kepada proyek yang
bersangkutan dan segala akibat karenanya bukan menjadi tanggungjawab pemberi dukungan.
2. Jika diberi dukungan dalam menawarkan harga lebih rendah dari harga yang telah ditentukan
atau ditawarkan pemberi dukungan.
Demikian Surat Dukungan ini kami buat untuk dapat dipergunakan sebagaimana yang ditentukan atau
ditawarkan oleh pemberi Dukungan.
Hormat Kami
PT. YU WON LCD,
Dengan Hormat,
Sebagai tempat usaha/galangan pembuatan kapal fiberglass, dengan ini memberi dukungan
sepenuhnya kepada :
Untuk mengikuti Pelalangan Paket Pekerjaan Pengadaan Speed Boat Maluku dan Maluku Utara
yang dilaksanakan oleh Pokja tersebut di atas tahun anggaran 2016.
EFENDI MASRI
Direktur
DATA PERSONALIA (TENAGA AHLI/TEKNIS)
PELAKSANA
2 SALEH UMAR 17/11/1967 STM 5 Tahun Konstruksi & Kekuatan Kapal Terlampir
LAPANGAN
ADMINISTRASI_
3 RUDY KIAT 06/01/1986 S M A 4 Tahun Administrasi Terlampir
KEUANGAN
1 Mesin Listrik (Ganseth) 1 Unit 10 Kva Honda 2011 Baik Ambon MILIK
2 Peralatan Tukang Kayu & Fiber 1 Set MAKITA/MAKTEC 2013 Baik Ambon MILIK
I. Material Langsung
770.065.000 96.258.125 866.323.125 22,5 96.258.125 962.581.250
(Bahan Baku)
II. Peralatan
1.848.156.000 231.019.500 2.079.175.500 54,0 231.019.500 2.310.195.000
(Barang Jadi)
76,5
A. Sub Total Barang 2.618.221.000 327.277.625 2.945.498.625 327.277.625 3.272.776.250
JASA
13,5
III. Jasa Umum 57.754.875 462.039.000 519.793.875 57.754.875 577.548.750
13,5
B. Sub Total Jasa 57.754.875 462.039.000 519.793.875 57.754.875 577.548.750
C. TOTAL BIAYA
2.675.975.875 789.316.625 3.465.292.500 90,0 385.032.500 3.850.325.000
(A+B)
A. DATA ADMINISTRASI
B. IZIN USAHA
1 Akta Pendirian CV
a. Nomor Akte : 13
b. Tanggal : 26 Februari 2004
c. Nama Notaris : ROSDIANA ELY, SH
2 Akta Perubahan Terakhir
a. Nomor Akte : 02
b. Tanggal : 04 Mei 2010
c. Nama Notaris : ROSDIANA ELY, SH
E. PENGURUS
Jabatan Dalam
No Nama No. KTP
Badan Usaha
2. Direksi/Pengurus Perusahaan
Jabatan Dalam
No Nama No. KTP
Badan Usaha
F. DATA KEUANGAN
1. Susunan Kepemilikan Saham (untuk PT)/Susunan Persero (untuk CV/Firma)
3. PPn :
Pengalama
Tahun
Tgl/Bln/ Thn Tingkat Jabatan Dalam n Profesi/
No Nama Sertifikat/
Lahir Pendidikan Pekerjaan Kerja keahlian
Ijazah
(tahun)
VERONIKA Perencanaan
1 14/02/1974 S1 Site Manager 4 Tahun Terlampir
TEHUBIJULUW, ST Kapal
Administrasi_
3 RUDY KIAT 06/01/1986 S M A 4 Tahun Administrasi Terlampir
Keuangan
H. Data Fasilitas/Peralatan/Perlengkapan
Status
Jenis Fasilitas/ Kapasitas
Merk & Tahun Kondi Lokasi Kepemilikan
No. Peralatan/ Jumlah atau
tipe Pembuatan si Sekarang /Dukungan
Perlengkapan output
Sewa
1 Mesin Listrik (Ganseth) 1 Unit 10 Kva Honda 2011 Baik Ambon MILIK
J. Dukunga Keuangan
Nama Bank : PT. Bank Maluku Cab. Utama Ambon
Nomor : KCU/02/003/I/2016
Tanggal : 06 Januari 2016
Nilai : Rp. 398.997.500,- (Tiga Ratus Sembilan Puluh Delapan Juta Sembilan Ratus
Sembilan Puluh Tujuh Ribu Lima Ratus Rupiah
Demikian Data Perusahaan ini saya buat dengan sebenarnya dan penuh rasa tanggung jawab.
Jika dikemudian hari ditemui bahwa data/dokumen yang saya sampaikan tidak benar dan ada
pemalsuan, maka saya dan badan usaha yang saya wakili bersedia dikenakan sanksi
administratif, sanksi pencantuman dalam Daftar Hitam, gugatan secara perdata, dan/atau
pelaporan secara pidana kepada pihak berwenang sesuai dengan ketentuan peraturan
perundang-undangan.