com
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 1/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
© BSN 2011
Hak cipta dilindungi undang-undang. Dilarang menyalin atau menggandakan sebagian atau seluruh isi
dokumen ini dengan cara dan dalam bentuk apapun dan dilarang mendistribusikan dokumen ini baik
secara elektronik maupun tercetak tanpa izin tertulis dari BSN
BSN
Gd. Manggala Wanabakti
Blok IV, Lt. 3,4,7,10.
Telp. +6221-5747043
Fax. +6221-5747045
Email: dokinfo@bsn.go.id
www.bsn.go.id
Diterbitkan di Jakarta
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 2/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Daftar isi
Daftar isi…………………………………………………………………………………………………i
Prakata…………………………………………………………………………………………………iii
1 Ruang lingkup……………………………………………………………………………………..1
2 Acuan normatif………………………………..…………………………………………………..1
3 Istilah dan definisi…………………………………………………………………………………1
4 Prinsip ................................................................................................................................ 3
5 Peralatan............................................................................................................................ 3
6 Benda uji ............................................................................................................................ 5
7 Prosedur ............................................................................................................................ 7
8 Perhitungan........................................................................................................................ 7
9 Laporan hasil uji ................................................................................................................. 9
Bibliografi ............................................................................................................................... 13
© BSN 2010 i
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 3/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Content
Contenti………………………………………………………………………………………………...ii
Foreword……………………………………………………………………………………………….iv
1 Scope................................................................................................................................. 2
2 Normative references ........................................................................................................ 2
3 Terms and definitions ........................................................................................................ 2
4 Principle............................................................................................................................. 4
5 Apparatus .......................................................................................................................... 4
6 Test specimens.................................................................................................................. 6
7 Procedure .......................................................................................................................... 8
8 Calculation......................................................................................................................... 8
9 Test report ....................................................................................................................... 10
Bibliography ........................................................................................................................... 14
© BSN 2010 ii
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 4/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Prakata
Standar Nasional
beban lentur Indonesiahasil
ini merupakan (SNI)adopsi
Ubin identik
keramikdengan
– Bagian 4: Penentuan
metode terjemahankuat lentur dan
(bilingual) dari
ISO 10545-4:2004 Ceramic tiles – Part 4: Determination of modulus of rupture and breaking
strength.
SNI ini disusun sesuai dengan ketentuan yang diberikan dalam Pedoman Standardisasi
Nasional (PSN) 03.1, Adopsi Standar Internasional dan Publikasi Internasional lainnya
Bagian 1: Adopsi Standar Internasional menjadi SNI (ISO/IEC Guide 21-1-2005, Regional or
national adoption of international Standards and other International Deliverables – Part 1:
Adoption of International Standard, MOD) dan PSN 08:2007 Penulisan SNI.
Standar ini disusun oleh Panitia Teknis 81-01, Industri Kaca dan Keramik dan telah dibahas
dalam rapat konsensus lingkup panitia teknis di Bandung pada tanggal 17 September 2008.
Hadir dalam rapat tersebut wakil dari pemerintah, produsen, konsumen, pakar akademis dan
peneliti serta instansi teknis terkait lainnya. SNI ini juga telah melalui konsensus nasional
yaitu pemungutan suara (voting) pada tanggal 22 Januari 2010 s.d 22 Februari 2010.
SNI ISO 10545, terdiri dari 17 bagian dengan menggunakan judul secara umum Ubin
keramik :
© BSN 2010 ii i
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 5/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Foreword
The
lenturNational Indonesia
dan beban Standard
lentur is identical(SNI) Ceramic
adoption Ubin keramik
by translation – Bagian
method 4: Penentuan
(bilingual) kuat
of ISO 10545-
4:2004 Ceramic tiles – Part 4: Determination of modulus of rupture and breaking strength.
For this purposed, the following editorial change have been made:
a) dot mark has been changed by comma and vice versa for the number writing,
b) terminology of International Standard has been changed by National Standard and
translated to be national standard.
The SNI was drafted accordance with the rules given in the National Standardization Guide
(PSN 03.1:2007), Adoption of International Standards and Other International Deliverables –
Part 1: Adoption of International Standards into SNI and PSN 08:2007, SNI Writing.
The SNI was prepared by Technical Committee 81-01, Glass and Ceramic Industry and has
been discussed in consensus meeting for Technical Committees in Bandung on 17
September 2008. The meeting was attended by the representatives from government,
producer, consumer, academic expert, researcher, and other related institution. This SNI has
passed national which is the voting conducted on 22 January 2010 until 22 February 2010.
SNI ISO 10545, consists of 17 parts with general title Ceramic tiles:
© BSN 2010 iv
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 6/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
1 Ruang lingku p
Standar Nasional Indonesia ini menetapkan metode uji untuk menentukan kuat lentur dan
beban lentur ubin keramik.
CATATAN ISO 13006 memberikan sifat-sifat yang diperlukan untuk ubin dan informasi berguna
lainnya pada produk tersebut.
2 Acuan normatif
Dokumen acuan berikut sangat diperlukan untuk penggunaan dokumen ini. Untuk acuan
bertanggal, hanya edisi tersebut yang digunakan. Untuk acuan tidak bertanggal, acuan
dengan edisi terakhir yang digunakan (termasuk semua amandemennya).
3.1
beban patah (breaking load)
Fbl
gaya yang diperlukan yang menyebabkan benda uji patah, seperti terbaca pada alat ukur
tekanan
3.2
kekuatan patah (breaking strength)
Fbs
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 7/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
1 Scope
This part of SNI ISO 10545 specifies a test method for determining the modulus of rupture
and breaking strength of all ceramic tiles.
NOTE ISO 13006 provides property requirements for tiles and other useful information on
these products.
2 Normati ve references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
For the purposes of this document, the following terms and definitions apply.
3.1
breaking load
Fbl
Force necessary to cause the test specimen to break, as read from the pressure gauge
3.2
breaking strength
Fbs
Force obtained by multiplying the breaking load by the ratio (span between support
rods)/(width of the test specimen)
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 8/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
3.3
modulus lentur (modulus of rupture)
σ Fbl
nilai yang diperoleh dengan membagi hasil perhitungan kekuatan patah oleh luas pada tebal
4 Prinsip
Penentuan beban patah, kekuatan patah dan modulus lentur ubin dinyatakan oleh gaya
yang bekerja pada laju tertentu di tengah-tengah ubin. Pastikan bahwa titik tumpu harus
kontak dengan permukaan ubin dengan baik.
5 Peralatan
Microwave, infra merah atau sistem pengering lainnya dapat digunakan apabila hasil yang
didapatkan sama.
5.3 Dua batang silin der penumpu, terbuat dari logam, bagian-bagian yang kontak
dengan benda uji terbungkus karet yang mempunyai kekerasan 50 IRHD ± 5 IRHD,,
pengukuran dilakukan sesuai dengan ISO 48.
Satu batang harus berada pada porosnya (lihat Gambar 1) dan batang lainnya harus dapat
sedikit berputar pada porosnya (Lihat Tabel 1 untuk penyesuaian dimensi).
5.4 Batang sil ind er tengah, diameter sama dengan batang-batang penumpu lain (5.3)
dan terbungkus karet yang sama, untuk transmisi beban Fbl. Batang ini juga harus berada
pada porosnya (lihat Gambar 1). (Lihat Tabel 1 untuk penyesuaian dimensi).
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 9/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
3.3
modulus of rupture
σ Fbl
quantity obtained by dividing the calculated breaking strength by the square by the square of
4 Principle
Determination of the breaking load, breaking strength and modulus of rupture of a tile by
applying a force at a specified rate to the centre of the tile, the point of application being in
contact with the proper surface of the tile.
5 Apparatus
Microwave, infrared or other drying systems may be used provided that it has been
determined that equal results are obtained.
5.3 Two cylindrical support rods, made of metal, the parts in contact with the test
specimens being covered with rubber having a hardness of (50 ± 5) IRHD, measured in
accordance with ISO 48.
One rod shall be slightly pivotable (see Figure 1) and the other shall be slightly rotatable
about its own axis. (See Table 1 for relevant dimensions).
5.4 Central cylindrical rod, of the same diameter as the support rods (5.3) and covered
with the same rubber, for transmission of the load Fbl.
This rod shall also be slightly pivotable (see Figure 1). (See Table 1 for relevant dimensions).
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 10/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Tabel 1 - Diameter batang penump u, d, ketebalan karet, t, dan bagian ubin yang
menutup sisi batang penumpu l 1
(lihat Gambar 2)
Keterangan gambar:
6 Benda uji
6.1 Pilih benda uji secara acak dari lot yang akan diuji. Apabila memungkinkan, yang
harus diuji adalah ubin utuh. Untuk ubin berukuran sisi-sisinya di atas 300 mm dapat
dilakukan pemotongan dan untuk beberapa yang bentuknya tidak empat persegi panjang,
sehingga dapat dipasang pada alat uji. Benda uji empat persegi panjang yang besar,
dipotong pada bagian tengah, yang merupakan bagian pusat atau titik tengah ubin. Dalam
hal masih meragukan, hasil yang diperoleh dari ubin yang utuh lebih dipilih dari hasil ubin
yang dipotong.
6.2 Jumlah minimal benda uji untuk setiap contoh sesuai Tabel 2.
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 11/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
6 Test specimens
6.1 Select the specimens at random from the lot to be tested. Whenever possible, whole
tiles shall be tested. However, it may be necessary to cut exceptionally large tiles (that is,
those greater than 300 mm in length) and some non-rectangular shapes in order to fit them
in the apparatus. Rectangular test specimens of the largest possible size shall then be cut,
having their centres coinciding with the centres of the tiles. In case of doubt, results obtained
using whole tiles shall always be preferred to results obtained with cut tiles.
6.2 The minimum number of test specimens for each sample is given in Table 2.
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 12/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Dimensi ubin
L Jumlah mini mal benda uji
18 ≤mm
L < 48 10
L ≥ 48 7
7 Prosedur
7.1 Bersihkan semua kotoran partikel yang melekat pada seluruh permukaan ubin depan,
belakang, atas dan bawah benda uji dengan kuas kaku. Keringkan setiap benda uji di dalam
oven (5.1) pada 110 °C ± 5 °C hingga didapatkan berat yang tetap, jika perbedaan antara
dua penimbangan berturut-turut pada interval 24 jam kurang dari 0,1 %. Benda uji dapat
didinginkan dalam oven tertutup atau dalam desikator berisi silika gel atau desikan lainnya
yang sesuai, tapi tidak mengandung asam, sampai tercapai suhu kamar. Benda uji harus
diuji tidak lebih dari 3 jam setelah suhu kamar tercapai.
7.2 Tempatkan benda uji pada batang penumpu (5.3) dengan permukaan yang berglasir
ditempatkan di bagian atas dengan memperhitungkan panjang, l1, benda uji (lihat Tabel 1
dan Gambar 2) melebihi masing-masing batang penumpu.
7.3 Dalam hal ubin yang dapat dibalik, seperti ubin mosaik tak berglasir, tidak masalah sisi
ubin mana yang berada paling atas. Untuk ubin yang diekstrusi, tempatkan benda uji secara
melintang tegak lurus terhadap batang penumpu. Untuk ubin empat persegi panjang
lainnya, tempatkan benda uji sehingga sisi terpanjang, L, berada tepat pada sudut-sudut
batang-batang penumpu.
7.4 Untuk ubin-ubin dengan permukaan bertekstur, tempatkan karet pada lapisan kedua
dengan ketebalan sesuai Tabel 1, pada batang penumpu tengah (5.4) yang menyentuh
permukaan bertekstur.
7.5 Posisi batang penumpu tengah sama jaraknya terhadap dua batang penumpu yang
lain. Pasang beban sehingga laju kenaikan tekanan yang didapat 1 N/(mm 2.s) ± 0,2
N/(mm2.s); laju awal per detik dapat dihitung dari Persamaan (2) di Butir 8. Catat beban
patah Fbl.
8 Perhitungan
Untuk menghitung beban lentur dan modulus lentur hanya digunakan hasil benda uji yang
patah di bagian tengah dengan posisi patahan di area diameter batang penekan. Minimal
lima hasil yang dapat diterima diperlukan untuk menghitung nilai rata-rata (mean).
Jika hasil yang dapat diterima kurang dari lima, contoh uji kedua harus diuji yang terdiri dari
dua kali jumlah ubin semula. Minimal 10 hasil yang dapat diterima digunakan untuk
menghitung nilai rata-rata (average).
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 13/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
18 ≤mm
L < 48 10
L ≥ 48 7
7 Procedure
7.1 Remove any loosely adhering particles from the back of each test specimen with a stiff
brush. Dry each test specimen in the oven (5.1) maintained at (110 ± 5) °C until constant
mass is reached, i.e. when the difference between two successive weighings at intervals of
24 h is less than 0,1 %. The test specimens may be cooled in the closed oven or in a
desiccator oven silica gel or another suitable desiccant, but not over an acid, until they reach
room temperature. Test specimens shall be tested no later than 3 h after they have reached
room temperature.
7.2 Place a test specimen on the support rods (5.3) with the glazed or proper surface
uppermost so that the test specimen projects by a length l1 (see Table 1 and Figure 2)
beyond each support rod.
7.3 In the case of reversible tiles, such as unglazed ceramic mosaic tiles, it does not matter
which side of the tile is uppermost. For extruded tiles, place the test specimen so that the
projecting ribs are at right angles to the support rods. For all other rectangular tiles, place the
test specimens so that the longer side, L, is at right angles to the support rods.
7.4 For tiles with a relief surface, place a second layer of rubber, of the appropriate
thickness given in Table 1, on the central rod (5.4) in contact with the relief surface.
7.5 Position the central rod equidistant between the support rods. Apply the load evenly in
such a way as to obtain a rate of increase in stress of (1 ± 0,2) N/mm2 per second; the actual
rate per second can be calculated by Equation (2) given in Clause 8. Record the breaking
load Fbl.
8 Calculation
Use only the results for test specimens that break within a central portion of length equivalent
to the diameter of the central rod to calculate the mean breaking strength and the mean
modulus of rupture. A minimum of five acceptable results is necessary to calculate the mean
value.
If there are fewer than five acceptable results, a second sample shall be tested consisting of
twice the number of tiles. A minimum of 10 acceptable results is then required to calculate
the average value.
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 14/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Kekuatan lentur (breaking strength) Fbs, dinyatakan dalam newton (N), dihitung dengan
Persamaan (1)
F bl l2
F bs = (1)
b
Keterangan:
l2 adalah jarak antara dua batang penumpu, dinyatakan dalam milimeter (mm) (lihat Gambar 2);
Modulus lentur σ Fbl, dinyatakan dalam newton per milimeter persegi (N/mm2), dihitung dari
Persamaan (2)
3F bl l2
σ F
bl
= 2
2bh
3F bs
= 2
(2)
2h
Keterangan:
l2 adalah jarak antara dua batang penumpu, dinyatakan dalam milimeter (mm) (lihat Gambar 2);
h adalah ketebalan minimal benda uji, dinyatakan dalam milimeter (mm), diukur setelah diuji
sepanjang sisi yang patah.
Perhitungan modulus lentur didasarkan pada bagian potongan melintang yang empat
persegi panjang. Dalam hal ini, ketebalan sepanjang sisi yang patah bervariasi. Tekstur
yang dangkal, lebih pasti untuk pendekatan.
Hitung rata-rata (mean) kekuatan lentur dan modulus lentur benda uji sebagai hasil rata-rata
(mean) yang dapat diterima.
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 15/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
The breaking strength Fbs, expressed in newtons, is calculated by means of Equation (1)
F bl l2
F bs = (1)
b
where
l2 is the span, expressed in millimetres, between the support rods (see Figure 2);
The modulus of rupture σ Fbl, expressed in newtons per square miilimetre, is calculated by
means of Equation (2)
3F bl l2
σ F
bl
= 2
2bh
3F bs
= 2
(2)
2h
where
l2 is the span, expressed in millimetres, between the support rods (see Figure 2);
h is the minimum thickness of the test specimen, expressed in millimetres, measured after
the test along the broken edge.
Calculate the mean breaking strength and the mean modulus of rupture of the sample as the
mean of the acceptable results.
9 Test report
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 16/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 17/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 18/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Bibliografi
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 19/20
5/24/2018 29087_SNIISO10545-4-2010-slidepdf.com
Bibliography
http://slidepdf.com/reader/full/29087sni-iso-10545-4-2010 20/20