Buku ini merupakan Laporan Analisis dan Disain Struktur untuk Gedung Ruko yang
berlokasi di Atambua Kabupaten Belu.
Gedung ini merupakan bangunan dengan fungsi Toko dan Kamar Tidur yang terdiri dari
3 (Tiga) lantai. Tipe konstruksi yang digunakan adalah beton bertulang.
Kami mengucapkan terima kasih kepada semua pihak yang telah memberikan kontribusi
dalam pembuatan laporan ini.
Perencana Struktur
Wahidin Ibrahim, ST
Halaman - i
RESUME DISAIN
I. Data Struktur
Halaman - 1
2. Modal direction (arah getaran eigen)
Modal Direction Factor (MDF)
Note: First two modes 1,2 must be translational (see below)
-------------------------------------------------------
Mode MDF,Dx MDF,Dz MDF,Ry Dominant Movement
-------------------------------------------------------
1 0.791074 0.003519 0.205407 Translational, DX
2 0.016192 0.976223 0.007585 Translational, DZ
3 0.361881 0.020437 0.617682 Rotational, RY
4 0.790579 0.028458 0.180964 Translational, DX
5 0.023658 0.968523 0.007819 Translational, DZ
6 0.016808 0.002851 0.980342 Rotational, RY
7 0.229169 0.000000 0.770831 Rotational, RY
8 0.770638 0.000003 0.229359 Translational, DX
9 0.000001 0.999988 0.000011 Translational, DZ
-------------------------------------------------------
Mode1 = translation Z Ok
Mode2 = translation X Ok
3. Kontribusi masa dalam pembentukan ragam getar bangunan
Modal Effective Mass Factor (EMF)
Note: EMF should be >= 100 Pct (SNI 1726-2019)
--------------------------------------
Mode EMF,Dx EMF,Dz EMF,Ry
--------------------------------------
1 55.0112 0.2925 16.2567 %
2 1.3789 79.2747 0.6108 %
3 26.0116 1.6002 49.3012 %
4 3.6656 0.1098 14.7640 %
5 0.1051 4.2926 0.4939 %
6 0.0501 0.0168 1.5548 %
7 3.1688 0.0000 13.5455 %
8 10.6086 0.0000 3.4728 %
9 0.0000 14.4134 0.0003 %
--------------------------------------
100.0000 100.0000 100.0000 %
--------------------------------------
EMF = 100% > 90% Ok
Halaman - 2
Base Shear Correction Factor, Vz = 1.2840
Dynamic Base Shear, Vd1 = 1.103151E+05 (ABS)
Dynamic Base Shear, Vd2 = 8.800955E+04 (SSR)
Dynamic Base Shear, Vd3 = 8.854636E+04 (CQC)
Static Equivalent, Vs = 8.132607E+04
Percentage of Vd3/Vs, r = 1.0888 = 108.88 %
Pondasi Footplat
1. Dimensi :
a. Type FP1 = BxH = 2.50 x 2.50 m
=t = 0.50 m
b. Type FP2 = BxH = 2.00 x 2.00 m
=t = 0.50 m
c. Type FP3 = BxH = 1.75 x 1.75 m
=t = 0.50 m
d. Type FP3 = BxH = 1.75 x 3.50 m
=t = 0.50 m
2. Tulangan :
a. Type FP1
Tulangan Atas D16 –150 mm
Tulangan Bawah D16 –150 mm
b. Type FP2
Tulangan Atas D16 –150 mm
Tulangan Bawah D16 –150 mm
c. Type FP3
Tulangan Atas D16 –150 mm
Tulangan Bawah D16 –150 mm
d. Type FP4
Tulangan Atas D16 –150 mm
Tulangan Bawah D16 –150 mm
Halaman - 3
Sloof Struktur
1. Dimensi :
a. S1(30X50) ; BxH = 0.30 x 0.40 m
2. Tulangan :
a. S1(30x40)
Balok Struktur
1. Dimensi :
a. B1(35x70) = BxH = 0.30 x 0.60 m
b. B2(30x50) = BxH = 0.30 x 0.45 m
c. B3(20x30) = BxH = 0.20 x 0.30 m
d. Ba(25x40) = BxH = 0.25 x 0.40 m
e. BR(30x45) = BxH = 0.30 x 0.45 m
2. Tulangan :
a. B1(30X60)
POSISI P TUMPUAN LAPANGAN TUMPUAN
Tulangan Atas Ta 6D16 4D16 6D16
Tulangan Bawah Tb 3D16 5D16 3D16
Sengkang S D10-100 D10-150 D10-100
Tul. Pinggang Tp 2D16
b. B2(30X45)
POSISI P TUMPUAN LAPANGAN TUMPUAN
Tulangan Atas Ta 4D16 3D16 4D16
Tulangan Bawah Tb 3D16 3D16 3D16
Sengkang S D10-100 D10-150 D10-100
Tul. Pinggang Tp 2D16
a. B3(20X30)
POSISI P TUMPUAN LAPANGAN TUMPUAN
Tulangan Atas Ta 2D16 2D16 2D16
Tulangan Bawah Tb 2D16 2D16 2D16
Sengkang S D10-100 D10-150 D10-100
Tul. Pinggang Tp ---
b. Ba(25X40)
POSISI P TUMPUAN LAPANGAN TUMPUAN
Tulangan Atas Ta 2D16 2D16 2D16
Tulangan Bawah Tb 2D16 2D16 2D16
Sengkang S D10-100 D10-150 D10-100
Tul. Pinggang Tp ---
c. BR(30X60)
POSISI P TUMPUAN LAPANGAN TUMPUAN
Tulangan Atas Ta 4D16 3D16 4D16
Tulangan Bawah Tb 3D16 3D16 3D16
Sengkang S D10-100 D10-150 D10-100
Tul. Pinggang Tp 2D16
Halaman - 4
Kolom Struktur
I. Kolom Beton
a. Dimensi :
K1(45x45) cm
b. Tulangan :
K1(45x45)
POSISI P TUMPUAN LAPANGAN
Tulangan Pokok Tp 12D19 12D19
Sengkang S D10-75 D10-150
Plat Lantai
Dimensi :
o t = 13 cm
Tulangan :
o t = 13 cm
Tulangan Atas Ø10 – 150 mm
Tulangan Bawah Ø10 – 150 mm
Plat Dak
Dimensi :
o t = 12 cm
Tulangan :
o t = 12 cm
Tulangan Atas Ø10 – 200 mm
Tulangan Bawah Ø10 – 200 mm
Halaman - 5
1. Data Struktur
2. Peraturan Disain
1. SNI-1727-2020, Beban desain minimum dan kriteria terkait untuk bangunan gedung dan
struktur lain
2. SNI-1726-2019, Standar Perencanaan Ketahanan Gempa untuk Struktur Bangunan
Gedung
3. SNI-2847-2019, Tata Cara Perhitungan Struktur Beton untuk Bangunan Gedung
4. SNI-1729-2020, Spesifikasi untuk bangunan gedung baja structural (ANSI/AISC 360-16,
IDT)
5. SNI-7860-2020, Ketentuan seismik untuk bangunan gedung baja Structural (ANSI/AISC
341-16, IDT)
6. SNI-7972-2020, Sambungan terprakualifikasi untuk rangka momen khusus dan menengah
baja pada aplikasi seismic (ANSI/AISC 358-16, IDT)
Halaman - 6
3. Sifat Material
- Concrete Material:
Kolom/Wall : K-250
Balok : K-250
Pelat : K-250
Pilecap : K-250
Sloof : K-250
Tangga : K-250
Non-struktural : K-175
Lantai kerja : K-125
- Steel Material:
Semua Tulangan : U-42, Ulir, D >= 10mm, Fy=4200 kg/cm2
Tulangan polos : U-28, polos, D < 10mm, Fy = 2800 kg/cm2
Baja Profil dan Pelat : BJ-37, Fu=3700 kg/cm2, Fy=2400 kg/cm2
Wiremesh : U-50 (hanya untuk pelat biasa non flat-slab) c. Welding :
Electrode : AWS E-70XX
4. Perhitungan Beban
a. Unit Weight of Materials
Berat sendiri struktur dihitung secara automatis oleh komputer sedangkan beban
tambahan pada balok dan plat diinput manual sesuai peraturan yang berlaku.
Halaman - 7
Gambar 1. Data beban plat lantai
5. Karakteristik Tanah
Sesuai hasil kegiatan penyelidikan tanah pada lokasi dengan data 2 (Tiga) titik
sondir, karakteristik tanah secara umum masuk dalam Kategori TANAH SEDANG
(Kategori Site SD).
6. Beban Gempa
Respos Spektra (http://rsa.ciptakarya.pu.go.id/2021/)
Halaman - 8
Halaman - 9
Besaran beban gempa:
7. Kombinasi Beban
Struktur harus didisain untuk mampu memikul beban maksimum akibat kombinasi
beban yang disyaratkan dalam peraturan yang berlaku
Halaman - 10
Halaman - 11
8. Pemodelan Struktur
Program Komputer : SANSPRO VER. 5.10 + Drawing Module
Deskripsi : Integrated Structural Analysis and Design System for
Building and General Structures
Model Gedung : Single and Multiple Diapraghms
Model Struktur : 2D and 3D Space Frame
Model Lantai Kaku : Yes
Rigid End Offset : Yes
Inersia Retak Efektif : Yes
Elemen Rangka Portal : 2-node Hermitian 3D Frame Element
Elemen Pelat Lentur : 9-node Quadrilateral Isoparametric Plate Bending Element
3/4-node Discrete Kirchoff Plate Bending Element
4-node Hybrid Formulation Plate Bending Element
3/4-node Assumed Deviatoric Stress Plate Bending Element
Kondensasi Statik : Yes (to get a 3-DOF/Floor Model)
Solusi Persamaan Linear : Variable Column Cholesky Method
Solusi Eigen Value : Subspace Iteration with Lanczos Starting Vector
Solusi Direct Integration : Modified Newmark Method, Wilson-Theta Method, Hilber-
Alpha Method
Metode Analisis : Linear Linear Elastic Dynamic Spectrum Response
Disain Komponen : Concrete Capacity Design for Beam, Column, Shearwall
Halaman - 12
9. Layout Struktur
S1(30X40)
K1(45x45)
Gambar 1. Layout Kolom dan Sloof untuk Lantai No. 0 (Level Lantai I elv. + 0.00)
Halaman - 13
B1(30X60)
B2(30X45)
B3(20X30)
Ba(25X40)
K1(45x45)
Gambar 2. Layout Kolom dan Balok untuk Lantai No. 2 (Level Lantai II elv. + 4.00)
Halaman - 14
Gambar 3. Rencana Plat Lantai untuk Lantai No. 2 (Level Lantai II elv. + 4.00)
Halaman - 15
B1(30X60)
B2(30X45)
B2(25X40)
K1(45X45)
`
Gambar 4. Layout Kolom dan Balok untuk Lantai No. 3 (Level Latai III Elv. + 8.00)
Halaman - 16
Gambar 5. Rencana Plat Lantai No. 3 untuk Lantai No. 3 (Level Lantai III elv. +8.00)
Halaman - 17
B1(30X60)
B2(30X45)
Ba(25X40)
K1(45X45)
Gambar 6. Layout Kolom dan Balok Dak (Level Lantai II Elv. +11.50)
Halaman - 18
Gambar 7. Layout Plat Lantai (Level Lantai II Elv. +11.5)
Halaman - 19
Gambar 8. Model Struktur 3D
Halaman - 20
10. Analisis Struktur
Proses analisis menghasilkan out-put berupa gaya berupa gaya-gaya dalam (M, N dan D),
deformasi lateral dan vertikal serta drift. Analisis struktur dilakukan secara komputerisasi dengan
menggunakan software SANSPRO VER. 5.20 + Drawing Module dengan prosedur sebagai berikut:
Halaman - 21
Evaluasi Kinerja Bangunan
Evaluasi kinerja bangunan lakukan dengan melihat hasil analisis terhadap beberapa syarat
yang ditetapkan dalam Tata Cara Perencanaan Ketahanan Gempa Untuk Struktur Bangunan Gedung
dan Non Gedung SNI 1726;2019 tahun 2019:
1. Periode getar struktur To ≤ Tmax (Dianjurkan untuk menjaga nilai To1 <= 1.4*0.0466*H^0.9 detik
dimana H adalah tinggi total bangunan. Jika To terlalu besar, maka gedung terlalu fleksibel, dan
akan menimbulkan drift/goyangan yang besar, juga beban gempa yang dihasilkan lebih kecil. Hal
ini akan mengakibatkan disain yang tidak konservatif;
Hasil evaluasi To = 0.57434 detik ≤ Tmax = 1.4*0.0466*H^0.9 = 0.66 detik Ok
2. Modal direction (arah getaran eigen) dari 2 mode pertama harus berupa perpindahan (translasi)
dalam arah X dan Y (DX dan DZ). Jika tidak terpenuhi kemungkinan gedung mengalami getaran
torsi (puntir), hal ini tidak baik untuk keamanan gedung, karena disain kapasitas yang digunakan
dilakukan dengan asumsi terjadi getaran translasi;
Hasil evaluasi Mode1 translation Z Ok
Mode2 translation X Ok
3. Pemeriksaan untuk Effective Mass Factor sesuai SNI 1726;2019 kontribusi masa dalam
pembentukan ragam getar bangunan harus >= 100%. Jika tidak terpenuhi kemungkinan yang
terjadi adalah jumlah eigen yang terlibat dalam analisis kurang, atau bangunan mengalami
getaran secara torsi;
Hasil evaluasi EMF = 100% = 100% Ok
4. Persyaratan rasio gaya geser dasar (Base Shear) untuk untuk analisis dinamik (Vd) dan analisis
statik ekivalen (Vs) untuk kedua arah X dan Z harus ≥ 100% hal ini untuk memastikan bahwa
analisis dinamik menyerap sejumlah energi yang sama dengan analisis statik ekivalen. Jika tidak
memenuhi perlu dikalikan dengan besaran factor.
Hasil Evaluasi : Rasio gaya geser dasar untuk arah X dan Z = 100% OK
5. Evaluasi drift yang bertujuan untuk mengetahui besar simpangan antara tingkat. Umumnya drift
yang besar terjadi pada saat bangunan mengalami beban lateral (gempa). Besar drift harus
dibatasi untuk mencegah terjadinya kerusakan dini pada elemen tembok atau dinding pengisi.
Dalam konsep disain bangunan berbasis kinerja, selain selain aspek kekuatan struktur, aspek
kekakuan juga menjadi salah satu indikator penting untuk menjamim kenyamanan pengguna
bangunan.
Hasil Evaluasi Drift antar tingkat OK
6. Evaluasi deformasi vertikal bertujuan untuk mecegah lendutan berlebihan yang dapat merusak
elemen nonstruktural yang berda di bawahnya, seperti tembok, partisis dan ornamen arsitektural
lainnya. Syarat lendutan sebesar L/240.dimana L adalah panjang bentangan balok
Hasil evaluasi deformasi terbesar pada balok lantai II Balkon sebesar -0.528 cm < L/240 =
0,528 cm < 600/240 = 2.5 cm OK
Halaman - 22
Deformasi Titik (DY = cm)
Gambar 10. Nodal Displacements DY Comb 2 untuk Lantai No. 2 (Level Lantai 2 elv. + 4.00)
Halaman - 23
Gambar 11. Nodal Displacements DY Comb 2 untuk Lantai No. 3 (Level Lantai III Elv. + 8.00)
Halaman - 24
Gambar 15. Nodal Displacements DY Comb 2 untuk Plat Atap
Halaman - 25
11. DISAIN ELEMEN STRUKTUR
Disain struktur untuk mendapatkan dimensi akhir dari elemen struktur dan jumlah tulangan
menggunakan input gaya-gaya dalam yang merupakan keluaran hasil analisis elemen struktur.
Proses disain struktur dilakukan secara komputerisasi dengan menggunakan software SANSPRO
VER. 5.10 + Drawing Module. Beberapa metode disain yang digunakan:
1. Luas Tulangan Utama Minimum dan Maksimum
Jikalau tidak diatur secara khusus, semua penampang beton bertulang harus memenuhi
persyaratan tulangan minimum dan maximum berikut ini
Halaman - 26
Dari aspek pendekatan desain, kedua sistem balok ini didesain dengan pendekatan yang
berbeda. Balok anak di desain dengan lebih memperhatikan pengaruh dari beban gravitasi (DL
dan LL) sedangkan bolok induk juga dipengaruhi oleh beban gempa yang bekerja pada kedua
arah utama bangunan. Dalam permodelan ini karena sloof juga dimasukan sebagai komponen
balok pada level lanta I sebagai balok induk, dengan demikian momen akibat gempa
mempengaruhi jumlah tulangan pada stiap section.
5. Disain Kolom Beton
Kolom didisain secara biaksial dimana kapasitas momen uniaksial dihitung dengan cara
kompatibilitas starin dengan constraint :
1. Jumlah gaya horisontal = P = aksial force
2. Momen kapasitas > Mu
Tulangan samping, tulangan atas/bawah, dan keadaan leleh tulangan turut diperhitungkan
secara otomatis. Pencarian garis netral dilakukan dengan cara iterasi yang dihentikan bila step
< 0.00001 cm. Kolom didesain dengan menggunakan pendekatan kolom kuat balok lemah atau
desain kapasitas. Dengan metode ini diharapkan kegagalan bangunan berupa terbentuknya
sendi plastis hanya terjadi pada pangkal-pangkal kolom.
6. Disain Plat
Disain pelat beton dilakukan seperti disain balok persegi dengan tulangan dobel untuk lebar 1
meter. Kontribusi tulangan atas dan bawah, dan pengaruh leleh atau tidaknya tulangan stress
tulangan turut diperhitungkan. Bangunan ini terdapat 2 (dua) jenis pelat, yakni Plat Lantai, Plat
Atap. Plat atap menutupi seluruh area tangga dengan fungsi utama sebagai penutup atap.
Sedangkan pelat lantai memiliki beberapa fungsi sebagai ruang kelas, ruang praktek dan
selasar.
7. Disain Baja
Notasi
Codes Requirements
Design Parameters:
Es = 2.10 E+06 kg/cm2
Halaman - 27
G = 0.81 E+06 kg/cm2
u = 0.30
at = 12 E-06 /deg.cent
Basic Stress :
Jenis Tegangan Leleh Tegangan Dasar
Baja Kg/cm2 Mpa Kg/cm2 Mpa
BJ 34 2100 210 1400 140
BJ 37 2400 240 1600 160
BJ 41 2500 250 1666 167
BJ 44 2800 280 1867 187
BJ 50 2900 290 1933 193
BJ 52 3600 360 2400 240
Tulangan geser = 0.58 x tegangan dasar
Disain Balok
Hasil disain elemen struktur sebagai output dari program SANSPRO VER. 5.20 + Drawing Module
secara lengkap dapat dilihat pada lampiran I
Halaman - 28
12. Disain Pondasi
Umum
Untuk mendapatkan gambaran daya dukung tanah dilakukan penyelidikan tanah
menggunakan alat sondir pada lokasi pekerjaan sebanyak 2 (Dua) titik, dengan gambaran
profil tanah seperti grafik berikut:
Halaman - 29
Beban Disain Pondasi.
Beban untuk disain pondasi diambil dari output reaksi perletakan struktur atas (Output
program) sebagai berikut:
Computer Program SANSPRO V.5.20
Structural Analysis and Design
(C) Nathan Madutujuh, ESRC, 2020
Licensee :
Project :
Model File : D:\TERKAIT\PAKETAN DESAIN\LEDELERO SIKA\SANS STR\SEMINARI LEDELERO RUBAH.MDL
Date : 07/12/2021
Output : Support Reactions
Halaman - 30
Perhitungan Daya Dukung Tanah.
Berdasarkan nilai tahan conus Qc dan besaran nilai reaksi perletakan dari struktur atas (output
program computer) maka direncanakan untuk Gedung ini menggunakan tipe pondasi dangkal
(footplat) yang diletakan pada kedalaman 1 m dari muka tanah asli.
Nilai Qc pada kedalaman 2 m dari data sondir sebesar 90 kg/cm2. Perhitungan daya dukung
tanah menggunakan menggunakan formula L. Herminier, sebagai berikut:
Qall = Qult/SF
Qult = qc/15
dimana:
Qall = daya dukung ijin (kg/cm2)
Qult = daya dukung ultimit (kg/cm2)
qc = tahanan ujung konus pada dasar pondasi.
15 = faktor reduksi
SF = angka keamanan (diambil 2)
Nilai qc titik sondir 1 pada kedalaman 2.00 m sebesar 40 kg/cm2 sehingga:
Qult = 40/15 = 2.60 kg/cm2
Qall = 2.6/2 = 1.3 kg/cm2
Disain Pondasi.
Disain pondasi dilakukan dengan menggunakan prorgam komputer Spread Footing Design For
Windows 1.0 yang merupakan salah satu program pelengkap dari Sans For Windows V.5.20.
Data gaya pondasi diperoleh dari analisis gaya yang dihasilkan oleh program Sans For
Windows V.5.20 dan beberapa data-data tambahan yaitu :
Mutu beton (fc’) : 20.5 Mpa
Mutu baja (fy) : 2400
Kedalaman pondasi dari muka tanah : 2,00 m
Daya dukung tanah : 1.3 kg/cm2
Berdasarkan besar beban dan sebaran pada titik pondasi, tipe pondasi footplat direncanakan
untuk 4 ukuran yaitu tipe 1 uk. 2.50x2.50m, tipe 2 dengan uk.2.00x2.00m, tipe 3 uk.1.75x1.75
&Tipe4denganuk.1.75x3.50
Halaman - 31
Gambar 12. Pembangian Tipe Pondasi Footplat
Halaman - 32
HASIL DISAIN PONDASI (OUTPUT PROGRAM KOMPUTER)
TIPE 1
BEBAN :
NU = Nmax = 66375.10000 KG
MUx = Mxmax = 469969.50000 KG.CM
Vux = Vux = 3559.80000 KG
DIMENSI PONDASI :
Panjang (B) = 250 cm
Lembar (H) = 250 cm
Tebal plat (t) = 50 cm
Licensee :
Project :
Job Name :
Foundation Type :
Design Code :
COLUMN/WALL DESIGN:
Halaman - 33
Note: One-way action is assumed.
Licensee :
Project :
Job Name :
Foundation Type :
Design Code :
Halaman - 34
Strength Reduction for Shear = 0.60
COLUMN/WALL DESIGN:
Halaman - 35
Soil Stress, at right side, fx2 = 0.807 kg/cm2
Shear Force, at right side, Vsx = 17243.160 kg
Location of Resultant, xs = 37.710 cm
Moment Force, Msx = 650233.294 kg.cm
Bending Rebar (X-RIGHT) = d16-15.0 cm
Licensee :
Project :
Job Name :
Foundation Type :
Design Code :
COLUMN/WALL DESIGN:
Halaman - 36
Minimum soil stress, q_min = 0.774 kg/cm2
Soil stress at left, q_left = 0.897 kg/cm2 -> OK
Soil stress at right, q_right = 0.774 kg/cm2 -> OK
Halaman - 37
LAMPIRAN 1. Hasil Disain Gedung (*.BTR)
SANSPRO for Windows V.5.20
Building Text Report
Version 1.1, 07 Mar 2002
Last Update: 30 Jan 2020
(C) Nathan Madutujuh, ESRC
PROJECT DATA:
Project :
Location :
Building :
File : D:\TERKAIT\PAKETAN DESAIN\RUKO ATAMBUA\SANS STR\RUKO ATB PA DO ULTI.MDL
Date : 13\08\2022
Licensee :
STRUCTURAL DATA:
Structure Model = 9 : Building1
Structure Material = 1 : Concrete
Structure Type = 0 : DuctileFrame
Design Method = 2 : Capacity
Design Code = 16 : ACI-2019
Steel Design Option = 1 : Linear
Importance Factor I = 1
UNIT SYSTEM:
Unit Type = 0
Unit Name = Modeler
Modulus = kg/cm2
Unit Weight = kg/cm3
Length = cm
Displacement = cm
Force = kg
Moment = kg.cm
Torsion = kg.cm
Stress = kg/cm2
Gravity Accel = cm/s2
ANALYSIS OPTION:
Analysis Method = 3 : Dynamic Spectrum Response
Linearity Model = 1 : Linear Static
Rigid Floor Option = 1
Gravity Acceleration = 981.00000
Condensation Level = 2
P-Delta Effects = 0
P-Delta Ductility Factor = 1.000
#1 Lateral Load Case with Pdelta = 0
#2 Lateral Load Case with Pdelta = 0
Include Slab Thickness for Beam Weight = 0
Use Effective Concrete Inertia = TRUE
Effective Inertia of Concrete Beam, Slab (Percent) = 50.000 25.000
Effective Inertia of Concrete Column (Percent) = 70.000
Effective Inertia of Concrete Shrwal (Percent) = 70.000 35.000
Effective Inertia of Steel Beam, Slab (Percent) = 80.000
Effective Inertia of Steel Column (Percent) = 80.000
Effective Area of Steel Truss (Percent) = 80.000
Use Rigid End Zone for Beam = 0
Stiffness Option for Plane Stress/Strain = 0
Shell FEM Formulation Method = 3
Halaman - 38
2.500 0.025 0.135 0.025
2.600 0.024 0.130 0.024
2.700 0.023 0.125 0.023
2.800 0.023 0.121 0.023
2.900 0.022 0.116 0.022
3.000 0.021 0.113 0.021
3.200 0.020 0.106 0.020
3.400 0.019 0.099 0.019
3.600 0.018 0.094 0.018
3.800 0.017 0.089 0.017
4.000 0.016 0.084 0.016
4.250 0.015 0.079 0.015
4.500 0.014 0.075 0.014
4.750 0.013 0.071 0.013
5.000 0.013 0.068 0.013
5.250 0.012 0.064 0.012
5.500 0.012 0.061 0.012
5.750 0.011 0.059 0.011
6.000 0.011 0.056 0.011
6.250 0.010 0.054 0.010
6.500 0.010 0.052 0.010
6.750 0.009 0.050 0.009
7.000 0.009 0.048 0.009
7.500 0.008 0.045 0.008
8.000 0.008 0.042 0.008
8.500 0.007 0.040 0.007
9.000 0.007 0.038 0.007
9.500 0.007 0.036 0.007
10.000 0.006 0.034 0.006
10.500 0.006 0.032 0.006
11.000 0.006 0.031 0.006
11.500 0.006 0.029 0.006
12.000 0.005 0.028 0.005
Maximum Output and Design Values are taken from All Load Combinations:
Comb Self WgtDead LoadLive Load Earthq-X
1 1.400 1.400 0.000 0.000
2 1.200 1.200 1.600 0.000
3 1.347 1.347 1.000 1.300
4 1.347 1.347 1.000 1.300
5 1.347 1.347 1.000 -1.300
6 1.347 1.347 1.000 -1.300
7 1.347 1.347 1.000 0.390
8 1.347 1.347 1.000 -0.390
9 1.347 1.347 1.000 0.390
10 1.347 1.347 1.000 -0.390
-----------------------------------------------------------------------------------
Beam Elements (Steel: frl,frm,frr,frv,frmx Concrete: nl/nl nm/nm nr/nr sl sr dcr)
Flr Idx s Len Vl Vr Ml Mm Mr Na Tr
-----------------------------------------------------------------------------------
-----------------------------------------------------------------------------------
Beam Elements (Steel: frl,frm,frr,frv,frmx Concrete: nl/nl nm/nm nr/nr sl sr dcr)
Halaman - 39
Flr Idx s Len Vl Vr Ml Mm Mr Na Tr
-----------------------------------------------------------------------------------
1 1 1 400.0 4.268 -4.299 -5.005 0.981 1.421 0.000 0.043 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.89
1 2 1 400.0 4.246 -4.173 -4.944 0.920 1.392 0.000 0.076 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.89
1 3 1 400.0 4.238 -4.181 -4.928 0.922 1.377 0.000 0.083 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.88
1 4 1 400.0 4.252 -4.198 -4.950 0.913 1.412 0.000 0.068 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.89
1 5 1 500.0 4.360 -4.324 -5.354 1.449 -0.188 0.000 0.089 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.93
1 6 1 400.0 4.202 -4.102 -4.895 0.985 1.266 0.000 0.087 | 3/ 3 2/ 2 2/ 2 8.6 8.6 0.94
1 7 1 200.0 7.032 -6.705 -6.081 0.286 5.321 0.000 0.133 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.89
1 8 1 600.0 4.852 -4.924 -6.598 2.086 -1.440 0.000 0.077 | 3/ 3 2/ 2 4/ 4 8.6 8.6 0.95
1 9 1 600.0 4.845 -4.883 -6.528 2.096 -1.411 0.000 0.072 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.96
1 10 1 600.0 4.911 -4.867 -6.702 2.101 -1.191 0.000 0.065 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.97
1 11 1 400.0 4.369 -4.441 -5.210 0.987 1.620 0.000 0.106 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.92
1 12 1 400.0 4.320 -4.326 -5.104 0.914 1.530 0.000 0.084 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.90
1 13 1 400.0 4.308 -4.331 -5.061 0.928 1.526 0.000 0.077 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.90
1 14 1 400.0 4.333 -4.335 -5.115 0.910 1.571 0.000 0.079 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.90
1 15 1 500.0 4.431 -4.397 -5.516 1.459 0.001 0.000 0.075 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.95
1 16 1 400.0 4.296 -4.220 -5.109 0.969 1.427 0.000 0.066 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.90
1 17 1 200.0 7.300 -7.233 -6.322 0.313 5.617 0.000 -0.006 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.95
1 18 1 400.0 2.317 -2.348 -3.624 0.326 2.541 0.000 0.068 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.75
1 19 1 400.0 2.293 -2.242 -3.556 0.268 2.513 0.000 0.072 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
1 20 1 400.0 2.276 -2.253 -3.521 0.265 2.479 0.000 0.079 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
1 21 1 400.0 2.324 -2.239 -3.583 0.290 2.611 0.000 0.074 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.74
1 22 1 500.0 1.983 -1.896 -3.366 0.409 1.699 0.000 0.070 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.69
1 23 1 400.0 2.168 -2.201 -3.368 0.324 2.199 0.000 0.070 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.69
1 24 1 200.0 5.511 -5.729 -5.132 0.185 5.114 0.000 0.079 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.92
1 25 1 400.0 2.284 -2.296 -3.555 0.325 2.476 0.000 0.078 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
1 26 1 400.0 2.260 -2.194 -3.491 0.267 2.448 0.000 0.073 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.72
1 27 1 400.0 2.243 -2.205 -3.456 0.266 2.414 0.000 0.067 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.71
1 28 1 400.0 2.304 -2.179 -3.538 0.293 2.573 0.000 0.075 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
1 29 1 500.0 1.938 -1.887 -3.275 0.391 1.566 0.000 0.056 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.68
1 30 1 400.0 2.119 -2.168 -3.233 0.358 2.139 0.000 0.070 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.67
1 31 1 200.0 5.493 -5.441 -5.153 0.146 5.058 0.000 0.075 | 3/ 3 2/ 2 3/ 3 8.6 8.6 0.93
1 32 1 600.0 5.161 -5.230 -7.475 2.128 -0.466 0.000 0.062 | 4/ 4 2/ 2 4/ 4 8.6 8.6 0.87
1 33 1 600.0 5.178 -5.157 -7.552 2.072 -0.441 0.000 0.065 | 4/ 4 2/ 2 4/ 4 8.6 8.6 0.86
1 34 1 600.0 5.232 -5.159 -7.641 2.116 -0.207 0.000 0.064 | 4/ 4 2/ 2 4/ 4 8.6 8.6 0.87
1 35 1 600.0 2.299 -2.288 -4.580 0.628 2.231 0.000 0.051 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.94
1 36 1 600.0 2.287 -2.249 -4.536 0.606 2.205 0.000 0.052 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.94
1 37 1 600.0 2.283 -2.307 -4.511 0.592 2.204 0.000 0.064 | 2/ 2 2/ 2 3/ 3 8.6 8.6 0.93
1 38 1 600.0 2.186 -2.145 -4.254 0.608 1.877 0.000 0.058 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.88
1 39 1 600.0 2.155 -2.131 -4.141 0.603 1.808 0.000 0.074 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.85
1 40 1 600.0 2.137 -2.197 -4.087 0.583 1.753 0.000 0.070 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.89
1 41 1 600.0 2.072 -2.038 -3.951 0.569 1.498 0.000 0.075 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.81
1 42 1 600.0 2.027 -2.052 -3.733 0.622 1.448 0.000 0.066 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.79
1 43 1 600.0 2.032 -2.078 -3.782 0.583 1.425 0.000 0.056 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.82
1 44 1 600.0 1.996 -1.987 -3.709 0.582 1.284 0.000 0.064 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.76
1 45 1 600.0 1.968 -1.986 -3.555 0.622 1.268 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.74
1 46 1 600.0 1.971 -2.012 -3.599 0.584 1.244 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.77
1 47 1 600.0 1.973 -1.969 -3.658 0.564 1.198 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.75
1 48 1 600.0 1.942 -1.969 -3.463 0.639 1.207 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
1 49 1 600.0 1.958 -1.985 -3.564 0.574 1.198 0.000 0.060 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.76
1 50 1 600.0 1.996 -1.999 -3.728 0.563 1.264 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.77
1 51 1 600.0 1.962 -1.999 -3.525 0.639 1.267 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.75
1 52 1 600.0 1.991 -2.005 -3.653 0.581 1.312 0.000 0.064 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.77
-----------------------------------------------------------------------------------
Range: Mmax=7.641, Vmax=7.300, Trmax=0.133, Nmin=0.000, Nmax=0.000
-----------------------------------------------------------------------------------
Column Elements (Steel: frl,frm,frr,frv,frmx Concrete: nbt,nbf,spc,ro,dcrx,dcry)
Flr Idx s Len Na Vx Vy Mx My
-----------------------------------------------------------------------------------
1 1 4 0.0 -40.224 3.717 4.065 7.654 7.106 | 10 0 4.7 1.40 1.00
1 2 4 0.0 -54.342 2.707 5.301 8.258 6.133 | 10 0 4.7 1.40 0.16
1 3 4 0.0 -53.850 2.838 4.895 8.814 6.329 | 10 0 4.7 1.40 0.16
1 4 4 0.0 -48.463 3.988 4.605 8.655 7.589 | 10 0 4.7 1.40 1.00
1 5 4 0.0 -47.907 4.872 3.687 7.114 7.910 | 10 0 4.7 1.40 0.15
1 6 4 0.0 -38.152 4.599 4.421 8.093 7.385 | 10 0 4.7 1.40 0.12
1 7 4 0.0 -37.898 4.502 4.385 7.890 7.409 | 10 0 4.7 1.40 0.12
1 8 4 0.0 -35.203 4.480 4.021 7.827 7.426 | 10 0 4.7 1.40 0.11
1 9 4 0.0 -41.465 4.165 4.694 8.566 7.340 | 10 0 4.7 1.40 0.13
1 10 4 0.0 -60.364 4.103 4.030 9.070 7.309 | 10 0 4.7 1.40 0.19
1 11 4 0.0 -57.934 7.105 4.414 9.742 7.944 | 10 0 4.7 1.40 0.15
1 12 4 0.0 -43.851 4.892 6.460 9.402 7.434 | 10 0 4.7 1.40 1.00
1 13 4 0.0 -41.187 3.811 5.027 7.344 6.494 | 10 0 4.7 1.40 0.13
1 14 4 0.0 -40.313 3.914 4.576 8.181 6.715 | 10 0 4.7 1.40 0.13
1 15 4 0.0 -41.226 3.769 4.832 7.109 6.563 | 10 0 4.7 1.40 0.13
1 16 4 0.0 -37.874 3.665 4.391 7.446 6.623 | 10 0 4.7 1.40 0.12
1 17 4 0.0 -40.793 3.886 4.525 7.965 6.778 | 10 0 4.7 1.40 0.13
1 18 4 0.0 -37.704 3.846 4.222 7.929 6.843 | 10 0 4.7 1.40 0.12
1 19 4 0.0 -43.109 5.009 4.041 6.697 8.110 | 10 0 4.7 1.40 0.13
1 20 4 0.0 -35.148 4.837 4.085 6.814 7.993 | 10 0 4.7 1.40 0.11
1 21 4 0.0 -38.737 4.698 4.325 7.216 7.953 | 10 0 4.7 1.40 0.12
1 22 4 0.0 -62.689 4.677 4.781 8.278 7.652 | 10 0 4.7 1.40 0.19
1 23 4 0.0 -63.071 7.275 4.529 9.625 8.714 | 10 0 4.7 1.40 0.16
1 24 4 0.0 -49.958 5.234 6.157 11.486 7.988 | 10 0 4.7 1.40 1.00
1 25 4 0.0 -67.738 4.443 5.776 11.301 6.956 | 10 0 4.7 1.40 0.18
1 26 4 0.0 -80.375 5.981 5.712 10.784 7.917 | 10 0 4.7 1.40 0.22
1 27 4 0.0 -84.399 3.844 5.091 9.605 6.844 | 10 0 4.7 1.40 0.27
1 28 4 0.0 -43.175 3.987 4.317 8.378 6.345 | 10 0 4.7 1.40 0.13
1 29 4 0.0 -48.422 3.996 4.638 7.871 6.068 | 10 0 4.7 1.40 0.15
1 30 4 0.0 -78.647 4.391 5.240 9.679 6.987 | 10 0 4.7 1.40 0.25
1 31 4 0.0 -70.194 5.925 5.824 10.840 7.461 | 10 0 4.7 1.40 0.20
1 32 4 0.0 -61.960 4.230 5.990 11.407 6.812 | 10 0 4.7 1.40 0.16
-----------------------------------------------------------------------------------
Range: Nmin=0.000, Nmax=84.399, Mmax=11.486, Vmax=7.275, Trmax=0.000
-----------------------------------------------------------------------------------
Beam Elements (Steel: frl,frm,frr,frv,frmx Concrete: nl/nl nm/nm nr/nr sl sr dcr)
Flr Idx s Len Vl Vr Ml Mm Mr Na Tr
-----------------------------------------------------------------------------------
Halaman - 40
2 1 3 250.0 4.929 0.903 -4.468 1.346 3.564 0.000 0.076 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.94
2 2 3 250.0 -0.313 -4.267 2.751 2.433 -1.503 0.000 0.130 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.78
2 3 3 300.0 3.573 -1.464 -2.195 2.708 1.850 0.000 0.148 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.57
2 4 3 300.0 0.575 -4.511 1.356 1.071 -3.470 0.000 0.017 | 2/ 2 2/ 2 3/ 2 8.6 8.6 0.94
2 5 3 300.0 4.168 -0.809 -4.187 0.801 0.970 0.000 0.057 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.88
2 6 3 300.0 0.799 -4.178 0.780 0.795 -3.241 0.000 0.116 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.89
2 7 3 300.0 4.351 -0.751 -4.524 0.999 1.360 0.000 0.059 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.95
2 8 3 300.0 1.630 -3.399 1.004 2.643 -0.664 0.000 0.129 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.56
2 9 3 250.0 4.544 0.626 -4.176 1.032 2.817 0.000 0.044 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.88
2 10 3 250.0 -0.457 -4.378 2.034 1.254 -2.620 0.000 0.107 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.80
2 11 3 250.0 4.809 0.883 -4.598 1.088 3.155 0.000 0.074 | 3/ 2 2/ 2 2/ 2 8.6 8.6 0.94
2 12 3 250.0 -0.745 -4.708 2.353 1.235 -3.020 0.000 0.109 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.91
2 13 3 200.0 3.602 0.853 -3.416 0.275 1.592 0.000 0.037 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.72
2 14 3 200.0 -0.866 -3.727 1.097 0.062 -2.567 0.000 0.116 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.78
2 15 3 300.0 3.000 -1.644 -1.671 2.373 1.201 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.50
2 16 3 300.0 0.861 -3.888 0.872 0.889 -2.894 0.000 0.128 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.84
2 17 3 300.0 3.688 -0.936 -3.615 0.635 0.594 0.000 0.056 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.76
2 18 3 300.0 0.977 -3.647 0.439 0.690 -2.706 0.000 0.101 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.74
2 19 3 300.0 3.768 -0.980 -3.815 0.855 0.888 0.000 0.062 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.81
2 20 3 300.0 1.723 -2.931 0.444 2.268 -0.448 0.000 0.120 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.48
2 21 3 200.0 3.192 0.513 -2.785 0.404 1.373 0.000 0.069 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.59
2 22 3 200.0 -0.851 -3.646 0.999 -0.064 -2.636 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.78
2 23 3 200.0 3.562 0.797 -3.236 0.437 1.691 0.000 0.115 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.68
2 24 3 200.0 -1.130 -3.960 1.274 0.023 -2.918 0.000 0.060 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.86
2 25 3 200.0 3.480 0.664 -2.925 0.656 1.860 0.000 0.048 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.62
2 26 3 200.0 -1.013 -3.782 1.482 0.438 -2.475 0.000 0.106 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
2 27 3 200.0 3.536 0.815 -3.096 0.467 1.781 0.000 0.064 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.65
2 28 3 200.0 -0.650 -3.362 1.337 0.602 -1.896 0.000 0.065 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.58
2 29 3 200.0 3.526 0.705 -2.968 0.666 1.910 0.000 0.111 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.63
2 30 3 200.0 -0.966 -3.737 1.509 0.521 -2.354 0.000 0.058 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.70
2 31 3 300.0 3.048 -1.591 -1.705 2.338 1.244 0.000 0.163 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.49
2 32 3 300.0 0.841 -3.881 0.929 0.936 -2.836 0.000 0.018 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.82
2 33 3 300.0 3.639 -0.985 -3.568 0.598 0.465 0.000 0.061 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.75
2 34 3 300.0 0.997 -3.627 0.334 0.613 -2.747 0.000 0.091 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.75
2 35 3 300.0 3.853 -0.864 -3.830 0.947 1.121 0.000 0.113 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.81
2 36 3 300.0 1.564 -3.079 0.733 2.261 -0.694 0.000 0.071 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.48
2 37 3 200.0 3.521 0.739 -2.962 0.522 1.853 0.000 0.049 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.63
2 38 3 200.0 -0.694 -3.498 1.364 0.631 -1.956 0.000 0.104 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.62
2 39 3 300.0 3.144 -1.483 -1.763 2.427 1.496 0.000 0.112 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.51
2 40 3 300.0 0.711 -3.998 1.201 1.007 -2.958 0.000 0.067 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.84
2 41 3 300.0 3.646 -0.978 -3.648 0.523 0.397 0.000 0.075 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.77
2 42 3 300.0 1.019 -3.605 0.256 0.574 -2.775 0.000 0.073 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.74
2 43 3 300.0 3.886 -0.813 -3.833 1.025 1.237 0.000 0.058 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.81
2 44 3 300.0 1.270 -3.522 0.903 1.916 -1.481 0.000 0.111 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.65
2 45 3 150.0 2.309 0.007 -2.237 -0.291 -0.031 0.000 0.155 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.47
2 46 3 200.0 3.426 0.727 -2.825 0.444 1.745 0.000 0.068 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.60
2 47 3 200.0 -0.753 -3.484 1.315 0.479 -2.123 0.000 0.061 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.63
2 48 3 200.0 3.435 0.678 -2.910 0.500 1.738 0.000 0.106 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.61
2 49 3 200.0 -0.611 -3.368 1.267 0.627 -1.886 0.000 0.044 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.60
2 50 3 300.0 3.082 -1.578 -1.746 2.407 1.337 0.000 0.105 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.51
2 51 3 300.0 0.774 -3.930 1.077 1.005 -2.900 0.000 0.095 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.84
2 52 3 300.0 3.604 -1.020 -3.612 0.593 0.390 0.000 0.092 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.76
2 53 3 300.0 1.065 -3.559 0.219 0.645 -2.699 0.000 0.077 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.74
2 54 3 300.0 3.795 -0.886 -3.757 1.042 1.061 0.000 0.072 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.79
2 55 3 300.0 1.377 -3.514 0.783 1.885 -1.351 0.000 0.121 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.67
2 56 3 150.0 2.320 -0.110 -2.274 -0.241 -0.061 0.000 0.116 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.48
2 57 3 200.0 3.869 0.663 -4.165 0.697 1.816 0.000 0.125 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.88
2 58 3 200.0 -0.432 -3.496 1.245 0.499 -1.846 0.000 0.030 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.64
2 59 3 200.0 3.822 0.772 -4.078 0.588 1.807 0.000 0.106 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.86
2 60 3 200.0 -0.511 -3.527 1.307 0.426 -1.997 0.000 0.059 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.64
2 61 3 200.0 3.951 0.827 -4.239 0.660 1.934 0.000 0.072 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.89
2 62 3 200.0 -0.505 -3.567 1.325 0.525 -1.893 0.000 0.105 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.65
2 63 3 200.0 4.003 1.061 -3.861 0.354 2.062 0.000 0.095 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.82
2 64 3 200.0 -0.531 -3.442 1.599 0.988 -1.463 0.000 0.131 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.53
2 65 3 200.0 2.253 -1.116 -1.655 0.153 0.493 0.000 0.042 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.35
2 66 3 200.0 4.077 1.171 -4.089 0.294 2.060 0.000 0.119 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.86
2 67 3 200.0 -0.255 -3.197 1.537 1.219 -0.948 0.000 0.121 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.44
2 68 3 200.0 1.816 -1.630 -1.082 0.287 0.191 0.000 0.019 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.30
2 69 3 300.0 3.161 -1.671 -2.264 1.975 0.791 0.000 0.147 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.48
2 70 3 300.0 0.870 -3.799 0.534 0.837 -2.888 0.000 0.028 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.84
2 71 3 300.0 3.970 -0.847 -4.250 1.017 1.134 0.000 0.113 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.90
2 72 3 300.0 1.659 -3.206 0.744 2.469 -0.358 0.000 0.074 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.52
2 73 3 150.0 -0.919 -3.523 -0.010 -0.873 -2.288 0.000 0.070 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.80
2 74 3 150.0 -0.950 -3.482 -0.044 -0.918 -2.357 0.000 0.078 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.80
2 75 3 150.0 -0.867 -3.443 -0.030 -0.854 -2.230 0.000 0.085 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.78
2 76 8 300.0 1.779 -0.961 -1.206 0.989 0.505 0.000 0.086 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.38
2 77 8 300.0 0.712 -2.053 0.114 0.524 -1.123 0.000 0.038 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.58
2 78 8 300.0 1.939 -0.815 -1.741 0.405 0.199 0.000 0.012 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.54
2 79 8 300.0 0.830 -1.933 -0.167 0.410 -1.060 0.000 0.026 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.55
2 80 8 300.0 2.015 -0.738 -1.771 0.543 0.445 0.000 -0.004 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.55
2 81 8 300.0 0.896 -1.897 0.061 0.812 -0.725 0.000 0.000 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.52
2 82 8 150.0 1.099 -0.207 -0.999 -0.060 -0.015 0.000 -0.045 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.31
2 83 8 150.0 0.197 -1.109 -0.118 -0.093 -0.497 0.000 0.096 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.32
2 84 8 200.0 1.611 -0.465 -1.557 0.557 0.497 0.000 -0.024 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.49
2 85 8 200.0 0.353 -1.516 0.142 0.381 -0.418 0.000 0.058 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.40
2 86 8 200.0 1.542 -0.336 -1.269 0.384 0.514 0.000 -0.034 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.40
2 87 8 200.0 0.440 -1.437 0.211 0.614 -0.100 0.000 0.009 | 2/ 2 2/ 2 2/ 2 6.1 6.1 0.35
2 88 7 150.0 -2.530 -6.669 -0.847 -2.029 -4.752 0.000 0.363 | 3/ 3 3/ 2 3/ 2 9.8 9.8 0.96
2 89 7 200.0 7.792 1.970 -9.665 2.406 4.884 0.000 0.426 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.96
2 90 7 200.0 -1.544 -7.789 3.513 2.109 -1.518 0.000 0.243 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.87
2 91 7 200.0 7.630 2.153 -8.520 1.967 4.635 0.000 0.303 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.87
2 92 7 200.0 -2.172 -7.576 3.607 2.086 -2.169 0.000 0.235 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.87
2 93 7 200.0 7.713 2.196 -8.744 2.028 4.735 0.000 0.232 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.89
2 94 7 200.0 -2.043 -7.568 3.619 2.180 -1.946 0.000 0.180 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.85
2 95 7 200.0 7.270 1.706 -8.278 2.034 4.253 0.000 0.274 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.83
2 96 7 200.0 -2.170 -7.746 3.150 1.525 -2.727 0.000 0.254 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.97
2 97 7 250.0 9.070 3.017 -11.147 2.367 7.259 0.000 0.240 | 5/ 3 3/ 3 2/ 3 9.8 9.8 0.93
2 98 7 250.0 -2.943 -9.046 5.617 2.663 -4.826 0.000 0.361 | 2/ 3 3/ 3 5/ 3 9.8 9.8 0.93
2 99 7 200.0 10.363 2.520 -11.658 2.185 5.684 0.000 0.499 | 5/ 3 3/ 3 2/ 3 9.8 9.8 0.93
2 100 7 200.0 -1.518 -9.427 4.529 2.999 -2.016 0.000 0.531 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.93
2 101 7 200.0 8.859 -7.213 -8.124 0.231 7.008 0.000 -0.014 | 4/ 3 3/ 3 3/ 3 9.8 9.8 0.92
2 102 7 150.0 -1.394 -5.704 -1.097 -1.554 -3.736 0.000 0.689 | 3/ 3 3/ 2 3/ 2 9.8 9.8 0.74
2 103 7 200.0 9.280 0.618 -10.716 3.281 4.946 0.000 -0.043 | 5/ 3 3/ 3 2/ 3 9.8 9.8 0.90
Halaman - 41
2 104 7 200.0 -0.225 -9.575 3.360 2.887 -0.966 0.000 0.419 | 2/ 3 3/ 3 5/ 3 9.8 9.8 0.89
2 105 7 200.0 9.487 0.863 -10.385 2.750 4.672 0.000 -0.120 | 5/ 3 3/ 3 2/ 3 9.8 9.8 0.89
2 106 7 200.0 -0.609 -9.155 3.504 3.163 -1.073 0.000 0.362 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.94
2 107 7 200.0 7.204 -0.398 -8.775 2.484 2.920 0.000 -0.363 | 4/ 3 3/ 3 2/ 3 9.8 9.8 0.95
2 108 7 200.0 0.713 -6.876 2.039 2.898 0.828 0.000 0.925 | 2/ 3 3/ 3 4/ 3 9.8 9.8 0.86
2 109 7 200.0 6.925 -0.801 -8.264 2.816 2.850 0.000 -0.274 | 4/ 3 3/ 3 2/ 3 9.8 9.8 0.88
2 110 7 200.0 0.590 -7.085 1.822 2.646 0.454 0.000 0.842 | 2/ 3 3/ 3 4/ 3 9.8 9.8 0.94
2 111 7 250.0 7.957 0.297 -10.012 2.721 4.456 0.000 -0.408 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.97
2 112 7 250.0 -0.155 -7.773 3.691 2.993 -1.828 0.000 1.056 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.92
2 113 7 200.0 7.302 -0.094 -9.115 2.515 3.258 0.000 -0.164 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.88
2 114 7 200.0 0.783 -6.734 2.413 2.874 0.874 0.000 1.271 | 2/ 3 3/ 3 3/ 3 9.8 9.8 0.92
2 115 7 200.0 9.843 -9.136 -8.427 0.584 7.644 0.000 0.292 | 4/ 3 3/ 3 4/ 3 9.8 9.8 0.96
2 116 2 600.0 7.674 -8.192 -14.394 3.048 4.201 0.000 0.115 | 4/ 3 2/ 3 5/ 3 10.0 10.0 0.99
2 117 2 300.0 8.969 -2.270 -14.379 5.402 4.328 0.000 0.503 | 4/ 3 3/ 3 2/ 3 10.0 10.0 0.98
2 118 2 300.0 2.067 -9.197 2.824 4.977 0.808 0.000 0.260 | 2/ 3 3/ 3 5/ 3 10.0 10.0 0.91
2 119 2 300.0 10.390 -2.268 -17.114 5.395 4.839 0.000 0.669 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.95
2 120 2 300.0 2.539 -9.468 2.841 7.797 4.326 0.000 0.142 | 2/ 3 3/ 3 5/ 3 10.0 10.0 0.88
2 121 2 600.0 7.309 -8.121 -13.417 2.890 2.991 0.000 0.099 | 4/ 3 2/ 3 5/ 3 10.0 10.0 0.98
2 122 2 300.0 9.562 -0.131 -15.226 5.427 6.887 0.000 0.798 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.95
2 123 2 300.0 -0.477 -10.302 5.039 4.221 -2.681 0.000 0.191 | 2/ 3 3/ 3 5/ 3 10.0 10.0 0.97
2 124 2 300.0 13.552 -0.155 -20.587 5.510 8.200 0.000 0.704 | 6/ 3 3/ 3 2/ 3 10.0 10.0 0.97
2 125 2 300.0 0.944 -12.488 6.920 8.389 0.437 0.000 0.044 | 2/ 3 3/ 3 6/ 3 10.0 10.0 0.87
2 126 2 300.0 10.189 -0.954 -15.324 7.347 8.152 0.000 1.591 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.89
2 127 2 300.0 -0.175 -11.792 5.711 3.787 -3.957 0.000 -0.738 | 2/ 3 3/ 3 6/ 3 10.0 10.0 0.98
2 128 2 300.0 13.821 1.708 -19.631 5.261 10.505 0.000 0.385 | 6/ 3 3/ 3 2/ 3 10.0 10.0 0.94
2 129 2 300.0 -2.218 -14.463 8.270 4.224 -8.685 0.000 0.349 | 2/ 3 3/ 3 7/ 4 10.0 10.0 0.96
2 130 2 300.0 15.782 2.572 -23.594 4.694 11.635 0.000 0.631 | 7/ 4 3/ 3 2/ 4 10.0 10.0 0.97
2 131 2 300.0 -1.229 -14.114 9.978 8.452 -2.974 0.000 0.410 | 2/ 4 3/ 3 6/ 3 10.0 10.0 0.97
2 132 2 300.0 13.354 1.838 -16.639 7.926 13.343 0.000 0.164 | 5/ 3 2/ 3 2/ 4 10.0 10.0 0.96
2 133 2 300.0 -3.374 -15.114 9.953 3.711 -10.932 0.000 0.635 | 2/ 4 3/ 3 7/ 4 10.0 10.0 0.98
2 134 2 300.0 12.718 2.195 -17.820 2.586 8.599 0.000 0.201 | 6/ 3 3/ 3 2/ 3 10.0 10.0 0.98
2 135 2 300.0 -3.059 -10.744 6.963 2.420 -8.568 0.000 0.659 | 2/ 3 3/ 3 5/ 3 10.0 10.0 0.98
2 136 2 300.0 12.197 3.278 -18.188 3.141 10.465 0.000 0.201 | 6/ 3 3/ 3 2/ 3 10.0 10.0 0.98
2 137 2 300.0 -1.978 -10.659 8.533 6.964 -2.402 0.000 0.909 | 2/ 4 3/ 3 5/ 3 10.0 10.0 0.98
2 138 2 300.0 9.737 1.532 -13.021 6.523 10.406 0.000 0.558 | 4/ 2 2/ 3 2/ 3 10.0 10.0 0.93
2 139 2 300.0 -2.703 -11.152 7.443 3.017 -7.211 0.000 0.352 | 2/ 3 3/ 3 5/ 3 10.0 10.0 0.98
2 140 2 300.0 9.285 1.952 -13.845 2.142 6.724 0.000 0.380 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.97
2 141 2 300.0 -1.969 -9.302 5.283 2.120 -7.007 0.000 0.418 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.97
2 142 2 300.0 11.014 2.568 -16.077 3.080 9.219 0.000 0.410 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.95
2 143 2 300.0 -1.544 -9.752 7.617 6.317 -2.173 0.000 0.509 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.92
2 144 2 300.0 12.356 1.440 -14.913 7.206 12.012 0.000 0.557 | 5/ 3 2/ 3 2/ 4 10.0 10.0 0.98
2 145 2 300.0 -2.640 -13.780 9.122 3.753 -9.564 0.000 0.330 | 2/ 4 3/ 3 6/ 3 10.0 10.0 0.97
2 146 2 300.0 9.444 2.170 -14.494 1.629 6.622 0.000 0.350 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.97
2 147 2 300.0 -2.153 -9.419 5.013 1.665 -7.737 0.000 0.432 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.99
2 148 2 300.0 13.424 2.243 -17.684 3.873 10.600 0.000 0.382 | 6/ 3 3/ 3 2/ 3 10.0 10.0 0.96
2 149 2 300.0 -1.668 -12.515 9.026 6.319 -5.539 0.000 0.656 | 2/ 4 2/ 3 5/ 3 10.0 10.0 0.98
2 150 2 150.0 3.071 -3.512 -3.132 -0.843 0.371 0.000 1.114 | 3/ 3 3/ 2 3/ 3 10.0 10.0 0.33
2 151 2 300.0 12.376 1.385 -14.959 7.283 12.028 0.000 0.508 | 5/ 3 2/ 3 2/ 4 10.0 10.0 0.95
2 152 2 300.0 -2.591 -13.810 9.200 3.834 -9.412 0.000 0.419 | 2/ 4 3/ 3 6/ 3 10.0 10.0 0.98
2 153 2 300.0 9.386 2.049 -14.504 1.678 6.427 0.000 0.396 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.97
2 154 2 300.0 -1.953 -9.348 4.927 1.789 -7.316 0.000 0.433 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.98
2 155 2 300.0 13.166 1.942 -17.298 3.987 10.263 0.000 0.349 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.98
2 156 2 300.0 -1.731 -12.622 8.768 5.748 -6.209 0.000 0.628 | 2/ 4 3/ 3 5/ 3 10.0 10.0 0.98
2 157 2 150.0 5.453 -1.323 -5.704 -1.566 0.905 0.000 0.813 | 3/ 2 3/ 2 3/ 3 10.0 10.0 0.51
2 158 2 300.0 12.772 1.000 -15.990 7.615 12.020 0.000 0.546 | 5/ 3 2/ 3 2/ 4 10.0 10.0 0.97
2 159 2 300.0 -2.333 -14.413 8.514 4.161 -8.838 0.000 0.240 | 2/ 4 3/ 3 6/ 3 10.0 10.0 0.98
2 160 2 300.0 10.045 1.558 -15.794 2.808 7.229 0.000 0.474 | 5/ 3 3/ 3 2/ 3 10.0 10.0 0.94
2 161 2 300.0 -1.686 -10.050 4.870 2.699 -6.153 0.000 0.194 | 2/ 3 3/ 3 5/ 3 10.0 10.0 0.92
2 162 2 300.0 13.801 1.542 -19.034 4.504 10.392 0.000 0.379 | 6/ 3 3/ 3 2/ 3 10.0 10.0 0.96
2 163 2 300.0 -1.460 -12.988 8.135 6.098 -5.607 0.000 0.243 | 2/ 4 3/ 3 6/ 3 10.0 10.0 0.97
2 164 2 150.0 5.315 -1.872 -5.333 -1.344 1.145 0.000 0.383 | 3/ 2 3/ 2 3/ 3 10.0 10.0 0.48
2 165 7 150.0 -0.267 -4.342 -1.162 -1.037 -2.478 0.000 -0.472 | 3/ 3 3/ 2 3/ 2 9.8 9.8 0.55
2 166 7 200.0 7.233 -0.442 -9.068 3.008 3.400 0.000 0.929 | 4/ 3 3/ 3 2/ 3 9.8 9.8 0.96
2 167 7 200.0 0.842 -7.161 2.408 2.885 0.944 0.000 -0.273 | 2/ 3 3/ 3 4/ 3 9.8 9.8 0.89
2 168 7 200.0 7.144 -0.283 -8.428 2.537 3.089 0.000 0.893 | 4/ 3 3/ 3 2/ 3 9.8 9.8 0.92
2 169 7 200.0 0.484 -6.905 2.241 2.845 0.546 0.000 -0.324 | 2/ 3 3/ 3 4/ 3 9.8 9.8 0.86
2 170 7 200.0 7.132 -0.316 -8.466 2.567 3.085 0.000 0.783 | 4/ 3 3/ 3 2/ 3 9.8 9.8 0.92
2 171 7 200.0 0.587 -6.841 2.195 2.859 0.663 0.000 -0.330 | 2/ 3 3/ 3 4/ 3 9.8 9.8 0.85
2 172 7 200.0 6.916 -0.612 -8.251 2.569 2.792 0.000 0.893 | 4/ 3 3/ 3 2/ 3 9.8 9.8 0.90
2 173 7 200.0 0.512 -6.948 1.884 2.585 0.315 0.000 -0.112 | 2/ 3 3/ 3 4/ 3 9.8 9.8 0.91
2 174 7 250.0 8.212 0.639 -10.312 2.539 4.704 0.000 0.875 | 5/ 3 3/ 3 2/ 3 9.8 9.8 0.94
2 175 7 250.0 -0.184 -7.630 3.948 3.289 -1.568 0.000 -0.484 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.86
2 176 7 400.0 5.464 -4.405 -7.739 0.835 3.081 0.000 -0.026 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.97
2 177 7 200.0 8.910 -8.752 -7.522 0.699 7.540 0.000 0.074 | 3/ 3 3/ 3 4/ 3 9.8 9.8 0.95
2 178 7 150.0 -2.569 -6.701 -0.813 -2.048 -4.801 0.000 0.445 | 3/ 3 3/ 2 3/ 2 9.8 9.8 0.97
2 179 7 200.0 7.850 2.109 -9.702 2.329 4.947 0.000 0.258 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.96
2 180 7 200.0 -1.638 -7.819 3.573 2.088 -1.633 0.000 0.263 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.87
2 181 7 200.0 7.684 2.297 -8.551 1.910 4.722 0.000 0.213 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.88
2 182 7 200.0 -2.246 -7.602 3.666 2.073 -2.256 0.000 0.318 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.86
2 183 7 200.0 7.704 2.273 -8.719 1.958 4.745 0.000 0.280 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.89
2 184 7 200.0 -2.064 -7.536 3.614 2.145 -2.002 0.000 0.370 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.84
2 185 7 200.0 7.279 1.809 -8.265 1.968 4.291 0.000 0.203 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.83
2 186 7 200.0 -2.294 -7.806 3.218 1.438 -2.939 0.000 0.312 | 2/ 3 3/ 3 4/ 2 9.8 9.8 0.91
2 187 7 250.0 9.400 3.354 -11.538 2.308 7.651 0.000 0.208 | 5/ 3 3/ 3 2/ 3 9.8 9.8 0.96
2 188 7 250.0 -2.918 -8.935 5.991 3.147 -4.312 0.000 0.683 | 2/ 3 3/ 3 5/ 3 9.8 9.8 0.97
2 189 7 200.0 5.287 0.265 -8.036 1.327 1.974 0.000 1.089 | 4/ 2 3/ 3 2/ 3 9.8 9.8 0.95
2 190 7 200.0 0.903 -4.199 1.389 2.404 1.936 0.000 -0.362 | 2/ 3 3/ 3 3/ 3 9.8 9.8 0.65
2 191 7 200.0 7.738 -7.510 -6.833 0.544 6.913 0.000 -0.018 | 3/ 3 3/ 3 3/ 3 9.8 9.8 0.92
-----------------------------------------------------------------------------------
Range: Mmax=23.594, Vmax=15.782, Trmax=1.591, Nmin=0.000, Nmax=0.000
-----------------------------------------------------------------------------------
Column Elements (Steel: frl,frm,frr,frv,frmx Concrete: nbt,nbf,spc,ro,dcrx,dcry)
Flr Idx s Len Na Vx Vy Mx My
-----------------------------------------------------------------------------------
2 1 4 0.0 -30.855 3.278 5.550 3.038 7.018 | 10 0 4.7 1.40 1.00
2 2 4 0.0 -43.000 3.087 4.986 11.323 6.092 | 10 0 4.7 1.40 1.00
2 3 4 0.0 -42.444 3.200 4.614 8.065 6.163 | 10 0 4.7 1.40 0.12
2 4 4 0.0 -39.146 3.507 4.977 11.153 7.322 | 10 0 4.7 1.40 1.00
2 5 4 0.0 -39.506 4.357 4.457 10.318 8.853 | 10 0 4.7 1.40 1.00
2 6 4 0.0 -35.363 4.315 4.758 7.590 9.048 | 10 0 4.7 1.40 1.00
2 7 4 0.0 -36.236 4.261 5.176 12.147 8.924 | 10 0 4.7 1.40 1.00
2 8 4 0.0 -29.771 4.073 5.158 3.077 8.184 | 10 0 4.7 1.40 1.00
Halaman - 42
2 9 4 0.0 -29.599 3.994 5.041 2.819 8.087 | 10 0 4.7 1.40 1.00
2 10 4 0.0 -36.381 4.080 5.005 11.764 8.414 | 10 0 4.7 1.40 1.00
2 11 4 0.0 -35.933 4.148 4.706 7.138 8.578 | 10 0 4.7 1.40 1.00
2 12 4 0.0 -34.799 4.466 4.690 11.081 8.028 | 10 0 4.7 1.40 1.00
2 13 4 0.0 -26.791 4.139 4.794 11.317 8.317 | 10 0 4.7 1.40 1.00
2 14 4 0.0 -32.896 4.087 4.526 8.372 8.305 | 10 0 4.7 1.40 0.10
2 15 4 0.0 -33.055 4.017 4.715 10.863 8.223 | 10 0 4.7 1.40 0.10
2 16 4 0.0 -26.870 3.969 4.734 3.385 8.061 | 10 0 4.7 1.40 1.00
2 17 4 0.0 -32.374 4.349 5.527 3.233 8.864 | 10 0 4.7 1.40 1.00
2 18 4 0.0 -43.116 4.848 5.201 12.021 10.647 | 10 0 4.7 1.40 1.00
2 19 4 0.0 -37.887 4.798 4.835 9.411 10.474 | 10 0 4.7 1.40 1.00
2 20 4 0.0 -29.587 4.440 5.168 12.184 9.060 | 10 0 4.7 1.40 1.00
2 21 4 0.0 -53.155 4.307 5.499 12.738 7.338 | 10 0 4.7 1.40 1.00
2 22 4 0.0 -79.007 3.872 4.867 9.610 6.765 | 10 0 4.7 1.40 0.25
2 23 4 0.0 -73.218 4.474 5.089 8.917 5.784 | 10 0 4.7 1.40 0.23
2 24 4 0.0 -50.838 4.408 4.639 5.152 6.546 | 10 0 4.7 1.40 1.00
2 25 4 0.0 -47.147 4.587 4.418 6.843 9.269 | 10 0 4.7 1.40 0.13
2 26 4 0.0 -61.448 4.288 5.758 10.094 8.378 | 10 0 4.7 1.40 0.18
2 27 4 0.0 -71.708 5.011 5.648 10.497 7.901 | 10 0 4.7 1.40 0.21
2 28 4 0.0 -52.237 5.317 5.425 12.120 9.069 | 10 0 4.7 1.40 1.00
2 29 4 0.0 -37.515 4.133 5.300 11.140 8.009 | 10 0 4.7 1.40 1.00
2 30 4 0.0 -52.442 3.635 5.806 11.833 7.301 | 10 0 4.7 1.40 0.14
2 31 4 0.0 -46.958 3.520 5.876 11.541 7.130 | 10 0 4.7 1.40 0.13
2 32 4 0.0 -32.001 3.769 4.987 6.772 7.715 | 10 0 4.7 1.40 1.00
-----------------------------------------------------------------------------------
Range: Nmin=0.000, Nmax=79.007, Mmax=12.738, Vmax=5.876, Trmax=0.000
-----------------------------------------------------------------------------------
Beam Elements (Steel: frl,frm,frr,frv,frmx Concrete: nl/nl nm/nm nr/nr sl sr dcr)
Flr Idx s Len Vl Vr Ml Mm Mr Na Tr
-----------------------------------------------------------------------------------
3 1 3 200.0 3.556 0.769 -1.644 1.906 3.296 0.000 0.045 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.70
3 2 3 200.0 -1.034 -3.814 2.600 1.664 -1.352 0.000 0.070 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.71
3 3 3 300.0 3.073 -1.564 -1.878 1.873 0.820 0.000 0.095 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.40
3 4 3 300.0 0.912 -3.734 0.643 0.832 -2.714 0.000 0.010 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.76
3 5 3 300.0 3.686 -0.938 -3.449 0.873 0.778 0.000 0.030 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.73
3 6 3 300.0 0.841 -3.783 0.664 0.763 -2.865 0.000 0.046 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.78
3 7 3 300.0 3.844 -0.800 -3.813 0.815 0.920 0.000 0.039 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.80
3 8 3 300.0 1.547 -3.094 0.704 1.944 -1.037 0.000 0.032 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.41
3 9 3 200.0 3.366 0.581 -1.660 1.714 2.905 0.000 0.102 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.61
3 10 3 200.0 -1.107 -3.889 2.175 1.119 -1.958 0.000 0.034 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.61
3 11 3 200.0 1.949 -0.718 -1.584 -0.080 -0.043 0.000 0.011 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.33
3 12 3 200.0 3.097 0.390 -1.425 1.716 2.626 0.000 0.027 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.55
3 13 3 200.0 -0.887 -3.637 1.951 1.079 -1.735 0.000 0.080 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.55
3 14 3 200.0 1.929 -0.706 -1.558 -0.071 -0.053 0.000 0.021 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.33
3 15 7 200.0 6.270 0.790 -5.701 1.778 3.456 0.000 0.863 | 3/ 2 3/ 3 2/ 3 9.8 9.8 0.72
3 16 7 200.0 -0.747 -6.216 2.832 1.738 -1.943 0.000 -0.580 | 2/ 3 3/ 3 3/ 2 9.8 9.8 0.70
3 17 7 200.0 4.498 -3.756 -3.729 0.029 2.306 0.000 0.007 | 3/ 3 3/ 3 3/ 3 9.8 9.8 0.47
3 18 2 300.0 9.154 0.380 -11.456 4.079 6.994 0.000 -0.586 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.82
3 19 2 300.0 -0.966 -9.763 5.640 2.623 -6.428 0.000 0.719 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.95
3 20 2 300.0 9.032 0.462 -12.097 2.506 5.542 0.000 -0.249 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.91
3 21 2 300.0 -0.472 -9.012 4.722 2.480 -5.830 0.000 0.776 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.90
3 22 2 300.0 9.589 0.750 -12.817 2.718 6.232 0.000 -0.334 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.96
3 23 2 300.0 -0.373 -9.128 5.663 3.919 -4.244 0.000 0.878 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.83
3 24 7 200.0 9.117 2.758 -7.706 2.705 6.490 0.000 0.213 | 3/ 2 2/ 3 2/ 3 9.8 9.8 0.97
3 25 7 200.0 -3.140 -9.597 5.133 1.948 -4.840 0.000 0.366 | 2/ 3 2/ 3 4/ 2 9.8 9.8 0.94
3 26 7 200.0 4.221 -2.376 -4.249 -0.388 2.465 0.000 -0.007 | 3/ 3 3/ 2 3/ 3 9.8 9.8 0.53
3 27 7 200.0 7.110 2.807 -6.671 2.289 5.600 0.000 0.228 | 3/ 2 3/ 3 2/ 3 9.8 9.8 0.84
3 28 7 200.0 -3.137 -7.528 4.249 1.622 -3.596 0.000 0.215 | 2/ 3 3/ 3 3/ 2 9.8 9.8 0.91
3 29 7 200.0 4.205 -3.254 -3.711 -0.010 2.113 0.000 0.024 | 3/ 3 3/ 2 3/ 3 9.8 9.8 0.47
3 30 7 200.0 6.228 0.690 -5.642 1.868 3.445 0.000 -0.559 | 3/ 2 3/ 3 2/ 3 9.8 9.8 0.71
3 31 7 200.0 -0.792 -6.323 2.813 1.686 -2.040 0.000 0.913 | 2/ 3 3/ 3 3/ 2 9.8 9.8 0.73
3 32 7 200.0 4.942 -4.269 -3.858 0.201 2.208 0.000 0.111 | 3/ 3 3/ 3 3/ 3 9.8 9.8 0.48
3 33 2 300.0 7.960 -0.959 -10.484 3.204 4.090 0.000 0.320 | 3/ 2 3/ 3 2/ 3 10.0 10.0 0.94
3 34 2 300.0 0.781 -8.155 3.408 2.856 -3.569 0.000 0.001 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.98
3 35 2 300.0 8.527 -0.728 -11.694 2.929 4.197 0.000 0.298 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.81
3 36 2 300.0 1.166 -7.934 3.652 4.254 -1.594 0.000 -0.009 | 2/ 3 3/ 3 3/ 2 10.0 10.0 0.92
3 37 2 300.0 6.101 0.359 -8.995 3.492 5.186 0.000 1.102 | 3/ 2 3/ 3 2/ 3 10.0 10.0 0.81
3 38 2 300.0 -0.918 -6.889 3.721 1.908 -3.543 0.000 -0.622 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.98
3 39 2 300.0 8.736 1.430 -12.124 3.089 6.822 0.000 0.402 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.89
3 40 2 300.0 -1.716 -9.034 5.425 2.552 -6.196 0.000 -0.129 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.98
3 41 2 300.0 9.580 1.957 -13.943 2.633 7.299 0.000 0.517 | 4/ 2 3/ 3 2/ 3 10.0 10.0 0.95
3 42 2 300.0 -1.336 -8.816 6.165 4.285 -3.892 0.000 -0.208 | 2/ 3 3/ 3 4/ 2 10.0 10.0 0.83
3 43 2 600.0 6.042 -6.608 -8.421 2.755 -1.436 0.000 0.027 | 3/ 3 2/ 3 3/ 2 10.0 10.0 0.87
3 44 7 400.0 2.149 -2.005 -3.245 0.473 1.862 0.000 0.038 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.41
3 45 7 400.0 2.031 -1.803 -2.890 0.302 1.744 0.000 0.068 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.36
3 46 7 400.0 2.003 -1.849 -2.858 0.293 1.665 0.000 0.097 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.36
3 47 7 400.0 2.115 -1.793 -3.002 0.356 1.968 0.000 0.037 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.38
3 48 7 500.0 1.761 -1.792 -2.818 0.316 0.534 0.000 0.426 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.35
3 49 7 600.0 1.971 -1.949 -3.536 0.555 0.437 0.000 0.104 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.44
3 50 7 600.0 1.831 -1.972 -2.758 0.784 0.373 0.000 0.062 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.40
3 51 7 600.0 1.900 -2.027 -3.111 0.628 0.434 0.000 0.086 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.46
3 52 7 400.0 2.145 -2.122 -3.220 0.497 1.869 0.000 0.198 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.40
3 53 7 400.0 1.965 -1.960 -2.794 0.280 1.575 0.000 0.106 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.35
3 54 7 400.0 1.926 -1.998 -2.673 0.322 1.541 0.000 0.074 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.35
3 55 7 400.0 2.068 -1.898 -2.927 0.337 1.855 0.000 0.063 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.37
3 56 7 500.0 1.741 -1.854 -2.758 0.324 0.490 0.000 -0.033 | 3/ 3 2/ 3 3/ 3 9.8 9.8 0.37
-----------------------------------------------------------------------------------
Range: Mmax=13.943, Vmax=9.763, Trmax=1.102, Nmin=0.000, Nmax=0.000
-----------------------------------------------------------------------------------
Column Elements (Steel: frl,frm,frr,frv,frmx Concrete: nbt,nbf,spc,ro,dcrx,dcry)
Flr Idx s Len Na Vx Vy Mx My
-----------------------------------------------------------------------------------
3 1 4 0.0 -6.294 1.216 2.493 3.678 3.454 | 10 0 4.7 1.40 1.00
3 2 4 0.0 -5.399 0.254 2.493 5.557 0.143 | 10 0 4.7 1.40 1.00
3 3 4 0.0 -5.465 0.275 2.061 4.169 0.129 | 10 0 4.7 1.40 1.00
3 4 4 0.0 -6.230 1.218 2.161 5.181 3.428 | 10 0 4.7 1.40 1.00
3 5 4 0.0 -4.540 2.251 1.022 3.989 5.216 | 10 0 4.7 1.40 1.00
3 6 4 0.0 -4.581 2.257 1.467 3.790 5.318 | 10 0 4.7 1.40 1.00
Halaman - 43
3 7 4 0.0 -4.505 2.146 1.451 3.761 5.132 | 10 0 4.7 1.40 1.00
3 8 4 0.0 -4.503 2.231 1.247 4.953 4.752 | 10 0 4.7 1.40 1.00
3 9 4 0.0 -4.626 2.049 1.261 5.031 4.993 | 10 0 4.7 1.40 1.00
3 10 4 0.0 -4.606 2.162 1.211 2.805 5.215 | 10 0 4.7 1.40 1.00
3 11 4 0.0 -4.821 2.364 1.713 4.091 5.212 | 10 0 4.7 1.40 1.00
3 12 4 0.0 -4.866 2.219 1.493 5.557 5.025 | 10 0 4.7 1.40 1.00
3 13 4 0.0 -23.915 2.248 5.325 10.990 6.242 | 10 0 4.7 1.40 1.00
3 14 4 0.0 -33.174 2.450 3.800 7.347 6.682 | 10 0 4.7 1.40 1.00
3 15 4 0.0 -37.256 1.998 3.863 7.472 6.587 | 10 0 4.7 1.40 1.00
3 16 4 0.0 -27.831 1.889 4.372 1.659 5.688 | 10 0 4.7 1.40 1.00
3 17 4 0.0 -29.353 2.945 3.374 3.830 4.731 | 10 0 4.7 1.40 1.00
3 18 4 0.0 -37.499 3.427 4.728 7.007 2.902 | 10 0 4.7 1.40 1.00
3 19 4 0.0 -34.868 3.828 4.283 8.049 2.879 | 10 0 4.7 1.40 1.00
3 20 4 0.0 -25.608 3.477 5.067 11.220 4.311 | 10 0 4.7 1.40 1.00
3 21 4 0.0 -18.711 1.990 4.115 9.704 4.446 | 10 0 4.7 1.40 1.00
3 22 4 0.0 -27.360 1.762 4.225 8.750 4.253 | 10 0 4.7 1.40 0.08
3 23 4 0.0 -24.398 1.781 4.518 8.045 4.527 | 10 0 4.7 1.40 0.08
3 24 4 0.0 -16.026 1.828 3.393 4.367 4.671 | 10 0 4.7 1.40 1.00
-----------------------------------------------------------------------------------
Range: Nmin=0.000, Nmax=37.499, Mmax=11.220, Vmax=5.325, Trmax=0.000
-----------------------------------------------------------------------------------
Beam Elements (Steel: frl,frm,frr,frv,frmx Concrete: nl/nl nm/nm nr/nr sl sr dcr)
Flr Idx s Len Vl Vr Ml Mm Mr Na Tr
-----------------------------------------------------------------------------------
4 1 7 200.0 -0.103 -1.264 0.553 0.306 -0.562 -0.140 0.207 | 2/ 3 2/ 3 3/ 2 9.8 9.8 0.11
4 2 7 200.0 -0.004 -1.183 0.402 0.258 -0.514 -0.190 -0.025 | 2/ 3 2/ 3 3/ 2 9.8 9.8 0.10
4 3 7 200.0 0.130 -0.891 0.234 0.217 -0.393 -0.007 -0.009 | 2/ 3 2/ 3 3/ 2 9.8 9.8 0.08
4 4 7 200.0 3.134 0.958 -2.577 0.793 2.155 -1.267 0.568 | 3/ 2 2/ 3 2/ 3 9.8 9.8 0.34
4 5 7 200.0 -1.063 -3.237 1.716 0.721 -1.670 -1.270 -0.292 | 2/ 3 2/ 3 3/ 2 9.8 9.8 0.36
4 6 7 200.0 0.710 -1.043 -0.369 0.088 -0.521 -0.049 -0.271 | 3/ 2 3/ 3 3/ 2 9.8 9.8 0.09
4 7 2 300.0 4.211 0.612 -3.957 1.776 3.794 -2.076 -0.347 | 3/ 2 2/ 3 2/ 3 10.0 10.0 0.38
4 8 2 300.0 -1.300 -3.489 3.121 0.763 -3.412 -2.090 0.689 | 2/ 3 2/ 3 3/ 2 10.0 10.0 0.41
4 9 2 600.0 1.882 -2.008 -1.960 1.107 -1.142 -0.805 0.028 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.21
4 10 2 300.0 6.343 1.161 -5.679 2.827 6.116 -2.129 0.114 | 3/ 2 2/ 3 2/ 3 10.0 10.0 0.59
4 11 2 300.0 -2.399 -4.835 5.000 1.039 -4.920 -2.138 -0.126 | 2/ 3 2/ 3 3/ 2 10.0 10.0 0.58
4 12 7 400.0 1.193 -1.057 -1.287 0.230 -0.006 -1.360 -0.049 | 3/ 2 2/ 3 3/ 2 9.8 9.8 0.17
4 13 7 400.0 1.268 -1.011 -1.434 0.244 0.148 -0.985 0.014 | 3/ 2 2/ 3 3/ 3 9.8 9.8 0.19
4 14 2 600.0 2.087 -1.762 -2.969 0.744 -0.919 -1.427 0.013 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.28
4 15 2 600.0 1.784 -2.016 -1.782 0.994 -1.551 -1.274 -0.012 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.23
4 16 7 400.0 1.278 -1.085 -1.414 0.292 0.208 -0.717 0.008 | 3/ 2 2/ 3 3/ 3 9.8 9.8 0.18
4 17 2 600.0 2.292 -1.578 -3.833 0.529 -0.556 -1.480 0.020 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.36
4 18 2 600.0 1.765 -2.056 -1.701 1.029 -1.583 -1.453 0.015 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.24
4 19 2 600.0 2.014 -1.917 -2.587 0.876 -0.978 -1.171 0.013 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.24
4 20 2 600.0 1.908 -1.983 -2.139 1.000 -1.165 -1.022 0.006 | 3/ 2 2/ 3 3/ 2 10.0 10.0 0.22
4 21 3 200.0 2.242 0.552 -1.170 0.839 1.903 -0.006 0.007 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.40
4 22 3 200.0 -0.809 -2.522 1.440 0.539 -1.404 0.002 -0.010 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.40
4 23 3 200.0 1.451 0.000 -1.451 -0.260 0.000 0.000 0.000 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.31
4 24 3 300.0 2.503 -1.862 -0.967 1.515 0.034 -0.021 -0.014 | 2/ 2 2/ 2 2/ 2 8.6 8.6 0.32
-----------------------------------------------------------------------------------
Range: Mmax=6.116, Vmax=6.343, Trmax=0.689, Nmin=-0.002, Nmax=2.138
-----------------------------------------------------------------------------------
Column Elements (Steel: frl,frm,frr,frv,frmx Concrete: nbt,nbf,spc,ro,dcrx,dcry)
Flr Idx s Len Na Vx Vy Mx My
-----------------------------------------------------------------------------------
4 1 4 0.0 -5.044 0.460 1.234 0.980 0.544 | 10 0 4.7 1.40 1.00
4 2 4 0.0 -7.220 0.408 0.417 1.345 0.503 | 10 0 4.7 1.40 1.00
4 3 4 0.0 -6.935 0.434 0.309 1.376 0.347 | 10 0 4.7 1.40 1.00
4 4 4 0.0 -5.068 0.420 1.542 4.296 0.608 | 10 0 4.7 1.40 1.00
4 5 4 0.0 -5.302 0.757 1.936 5.187 1.170 | 10 0 4.7 1.40 1.00
4 6 4 0.0 -6.507 1.134 0.253 1.022 1.750 | 10 0 4.7 1.40 1.00
4 7 4 0.0 -9.615 1.576 0.986 3.353 2.723 | 10 0 4.7 1.40 1.00
4 8 4 0.0 -12.134 1.411 2.857 4.456 2.014 | 10 0 4.7 1.40 1.00
4 9 4 0.0 -9.371 1.571 2.574 3.520 3.265 | 10 0 4.7 1.40 1.00
4 10 4 0.0 -8.744 1.743 1.029 2.699 5.176 | 10 0 4.7 1.40 1.00
4 11 4 0.0 -6.796 1.332 0.243 1.159 4.214 | 10 0 4.7 1.40 1.00
4 12 4 0.0 -5.493 0.858 1.763 4.646 2.523 | 10 0 4.7 1.40 1.00
-----------------------------------------------------------------------------------
Range: Nmin=0.000, Nmax=12.134, Mmax=5.187, Vmax=2.857, Trmax=0.000
PROJECT DATA:
Project :
Building : Analisis dan Disain Struktur
File :
Date :
Halaman - 44
Minimum Thickness (2-way slab with edge beams, no drop panel, U-39 = Lmin/33 = 9.09 cm
Maximum Deflection due to Live Load = Ln/360 = 8.33 mm
Maximum Deflection due to Total Load = Ln/240 = 12.50 mm
Spn,short=d10-240,Spn,long=d10-240,Sup,short=d10-240,Sup,long=d10-240
Halaman - 45
STATUS of f0 : f0 >= fn -> OK
Spn,short=d10-240,Spn,long=d10-240,Sup,short=d10-240,Sup,long=d10-240
Spn,short=d10-240,Spn,long=d10-240,Sup,short=d10-240,Sup,long=d10-240
Halaman - 46
LAMPIRAN 3. Data Sondir
Halaman - 47