STRUKTUR
Konstruksi Bangunan Gudang Industri
Pabrik Rokok
Alamat :
Desa Sukupuro, Kecamatan jabung, Kabupaten Malang
2023
0
PENDAHULUAN
1. Pendahuluan
Rencana konstruksi bangunan gedung insustri rokok ini terdiri dari 1 lantai dengan
gabungan struktur beton dan baja. Sedangkan konstruksi atapnya menggunakan
konstruksi gable frame baja dengan bentang 30.50m. Bentuk bangunan menyerupai
persegi panjang dengan ukuran 13,14m x 30,50m, dimana dipergunakan sebagai tempat
produksi rokok.
1
2.3.3. Beban
1. Beban Mati
Beban mati pada struktur bangunan ditentukan dengan menggunakan berat jenis
bahan bangunan dengan berdasarkan Peraturan Perencanaan Pembebanan untuk
Rumah dan Gedung 1987 dan unsur-unsur yang diketahui seperti pada denah
arsitektur dan struktur. Beban-beban yang diakibatkan oleh gravitasi yang
bersifat permanen dalam hal ini berat sendiri struktur. Beban mati yang
diperhitungkan adalah :
1. Beton = 2400 kg/m3
2. Baja = 7850 kg/m3
3. Beban Mati (Baja) = 115 kg/m (perhitungan excel)
4. Beban Dinding (Beton) = 330 kg/m , 165 kg/m (perhitungan excel)
2. Beban Hidup
Beban hidup yang diperhitungkan adalah sebagai berikut :
1. Beban Hidup (Baja) = 100 kg/m (Gording)
2. Beban Hidup (Beton) = 100 kg/m2
2023
Data masukan yang diperlukan untuk program Robot Structural Analysis dan spread
sheet Ms. Excell adalah properties penampang, material dan geometri dari struktur.
Kondisi-kondisi pembebanan juga diperlukan sebagai data masukan.
2
Seluruh beban-beban yang diterapkan pada struktur di bagi dalam beberapa kondisi
beban (load condition) dan pada akhir analisis kondisi beban-beban tersebut
dikombinasikan.
3.2.3. Penulangan
3.2.3.1. Balok Sloof
Penulangan lentur balok dihitung secara manual berdasarkan hasil/ output
program Robot Structural Analysis. Gaya geser dari balok dengan daktilitas terbatas
dihitung menurut persamaan berikut : Vu, b = 1.05 (VD,b + VL,b 4.0/K VE,b)
dimana :
VD,b = gaya geser balok akibat beban mati terfaktor
VL,b = gaya geser balik akibat beban hidup terfaktor
VE,b = gaya geser balok akibat beban gempa terfaktor
K = faktor jenis struktur (K > 2)
3.2.4. Kolom
Penulangan longitudinal dan geser dari kolom juga dilakukan dengan bantuan
program Ms. Excell dari Ms. Excell adalah jumlah luas tulangan untuk kolom yang
dibutuhkan. Perhitungan tulangan untuk kolom ini juga didasarkan pada teori
daktilitas terbatas. Momen lentur yang digunakan untuk mencari jumlah tulangan
dihitung menurut persamaan dibawah ini :
dimana :
MD, k = Momen balok akibat beban mati terfaktor
ML, k = Momen balok akibat beban hidup terfaktor
NE, k = gaya aksial balok akibat beban gempa terfaktor
wd = faktor pembebanan dinamis
3.2.5. Analisa Tegangan Baja
Pekerjaan pemeriksaan tegangan batang baja dilakukan oleh alat bantu program Cek
Tegangan Steel Frame Design yang merupakan “post processor” dari Robot
Structural Analysis.
Dengan menggunakan alat bantu ini, gaya-gaya batang yang merupakan hasil output
dari Robot Structural Analysis dijadikan input untuk menentukan tegangan batang
dan rasio tegangan Steel Frame Design. Output dari Steel Frame Design sendiri adalah
rasio tegangan yang merupakan perbandingan antara tegangan yang terjadi dengan
tegangan ijin baja.
4. Pondasi
4.1. Tipe Pondasi
Sesuai dengan data-data tanah, kondisi lingkungan dan engineering judgement, tipe
pondasi yang dipilih untuk struktur utama adalah pondasi footplate biasa.
4.2. Perhitungan Daya Dukung
Daya dukung tanah diasumsikan bedasarkan tabel.
3
PERMODELAN STRUKTUR
DAN PEMBEBANAN
1. Permodelan Struktur
Bangunan konstruksi baja gudang pakis dimodelkan sebagai struktur Open Frame (Struktur
Rangka Pemikul Momen). Dimana struktur terdiri atas rangka yang tersusun atas balok rafter
dan kolom yang menyangga beban dinding, beban angin, dan beban dari atap.
Rafter
Kolom Baja
Kolom Beton
Sloof
4
Gambar. – Frame Section Steel
5
1.2. Permodelan Pondasi
Pondasi footplate dimodelkan berperilaku sebagai jepit sehingga mampu mengekang
translasi dan rotasi searah sumbu lokal 1, 2, dan 3.
Adapun pemodelan sistem pondasi tersebut adalah sebagai berikut :
2. Permodelan Pembebanan
2.1. Permodelan Beban Mati dan Beban Hidup
Beban mati, hidup, dan beban angin juga juga dimodelkan sebagai beban merata
(Uniform load) dengan sepeti gambar berikut ini:
6
7
8
Gambar. – Pemodelan Pembebanan
9
3.2. Output Bending Moment Diagram
Output BDM (Bending Moment Diagram) dapat dilihat pada gambar berikut ini :
10
3.4. Output Normal Force Diagram
Output NFD (Normal ForceDiagram) dapat dilihat pada gambar berikut ini :
Gambar. – Ratio
11
CEK KEKUATAN
STRUKTUR
12
OUTPUT SOFTWARE
ROBOT STRUCTURAL
ANALISYS
Konstruksi Bangunan Gudang Industri
Pabrik Rokok
Alamat :
Jalan. Inspol Suwoto No. 89, RT. 01 RW. 08, Kec. Pisang Candi, Kota Malang, Jawa Timur
TITLE PAGE
Calculation note 3
Section properties 7
Project properties 8
Code combinations 9
Properties - Bars 10
Properties - Materials 11
Nodes 12
Bars 14
Quantity survey 17
Loads 18
Combinations 19
reactions: global extremes 20
displacements: global extremes 21
forces: global extremes 22
stresses: global extremes 23
Calculation note
Project properties: GEDUNG INDUSTRI & PABRIK ROKOK JABUNG
Structure description
Number of nodes: 91
Number of bars: 125
Bar finite elements: 134
Planar finite elements: 0
Volumetric finite elements: 0
No of static degr. of freedom: 384
Cases: 25
Combinations: 16
Excitation direction:
X= 1.000
Y= 0.000
Z= 0.000
Data:
Soil : D
S1 : 0.407
SS : 0.883
Spectrum parameters:
Fa = 1.147 Fv = 1.593
SMS = 1.013 SM1 = 0.649
SDS = 0.675 SD1 = 0.432
To = 0.128 TS = 0.640
TL = 20.000
I = 1.000 R = 8.000
Fundamental period:
Approximated method T = 0.299 (s)
RC frames Ct = 0.016 (0.0466) x = 0.90
Structure range:
Top story Level +7.90
Bottom story Level +4.33
Effective height Hn = 7.90(m)
Base shear
k = 1.000
Cs = 0.084
Cs max = 0.181
Cs min = 0.030
Effective seismic weight W = 51939.95(kG)
Shear force V = 42.99(kN)
Excitation direction:
X= 0.000
Y= 1.000
Z= 0.000
Data:
Soil : D
S1 : 0.407
SS : 0.883
Spectrum parameters:
Fa = 1.147 Fv = 1.593
SMS = 1.013 SM1 = 0.649
SDS = 0.675 SD1 = 0.432
To = 0.128 TS = 0.640
TL = 20.000
I = 1.000 R = 8.000
Fundamental period:
Approximated method T = 0.299 (s)
RC frames Ct = 0.016 (0.0466) x = 0.90
Structure range:
Top story Level +7.90
Bottom story Level +4.33
Effective height Hn = 7.90(m)
Base shear
k = 1.000
Cs = 0.084
Cs max = 0.181
Cs min = 0.030
Effective seismic weight W = 51939.95(kG)
Shear force V = 42.99(kN)
Section properties
Section properties:
C R350x350
WF 250x125x6
B R200x300
C R150x200
B R150x150
Project properties
Project name : GEDUNG INDUSTRI & PABRIK ROKOK JABUNG
Address:
City:
Phase:
Revision no.:
Comment:
Code combinations
Code Combinations
according to the regulation: LRFD ASCE 7-10
Properties - Bars
Section name Bar list AX (mm2) AY (mm2) AZ (mm2) IX (mm4) IY (mm4) IZ (mm4)
Properties - Materials
Nodes
Bars
Node Node Structure
Bar Section Material Length (m) Gamma (Deg) Type
1 2 object
1 1 2 C R350x350 CONCR 4.33 0.0 RC Column Column
2 3 4 C R350x350 CONCR 4.33 0.0 RC Column Column
3 2 5 WF 250x125x6 STEEL 1.30 0.0 Column Bar
4 4 6 WF 250x125x6 STEEL 1.30 0.0 Column Bar
5 5 7 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
6 7 6 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
122 143 7 C R150x200 CONCR 7.90 0.0 RC Column Column
126 151 152 C R150x200 CONCR 6.75 0.0 RC Column Column
127 153 154 C R150x200 CONCR 6.75 0.0 RC Column Column
205 259 260 C R350x350 CONCR 4.33 0.0 RC Column Column
206 261 262 C R350x350 CONCR 4.33 0.0 RC Column Column
207 260 263 WF 250x125x6 STEEL 1.30 0.0 Column Bar
208 262 264 WF 250x125x6 STEEL 1.30 0.0 Column Bar
209 263 265 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
210 265 264 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
211 266 267 C R350x350 CONCR 4.33 0.0 RC Column Column
212 268 269 C R350x350 CONCR 4.33 0.0 RC Column Column
213 267 270 WF 250x125x6 STEEL 1.30 0.0 Column Bar
214 269 271 WF 250x125x6 STEEL 1.30 0.0 Column Bar
215 270 272 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
216 272 271 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
217 273 274 C R350x350 CONCR 4.33 0.0 RC Column Column
218 275 276 C R350x350 CONCR 4.33 0.0 RC Column Column
219 274 277 WF 250x125x6 STEEL 1.30 0.0 Column Bar
220 276 278 WF 250x125x6 STEEL 1.30 0.0 Column Bar
221 277 279 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
222 279 278 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
223 280 281 C R350x350 CONCR 4.33 0.0 RC Column Column
224 282 283 C R350x350 CONCR 4.33 0.0 RC Column Column
225 281 284 WF 250x125x6 STEEL 1.30 0.0 Column Bar
226 283 285 WF 250x125x6 STEEL 1.30 0.0 Column Bar
227 284 286 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
228 286 285 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
229 287 288 C R350x350 CONCR 4.33 0.0 RC Column Column
230 289 290 C R350x350 CONCR 4.33 0.0 RC Column Column
231 288 291 WF 250x125x6 STEEL 1.30 0.0 Column Bar
232 290 292 WF 250x125x6 STEEL 1.30 0.0 Column Bar
233 291 293 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
234 293 292 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
235 294 295 C R350x350 CONCR 4.33 0.0 RC Column Column
236 296 297 C R350x350 CONCR 4.33 0.0 RC Column Column
237 295 298 WF 250x125x6 STEEL 1.30 0.0 Column Bar
238 297 299 WF 250x125x6 STEEL 1.30 0.0 Column Bar
239 298 300 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
240 300 299 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
241 301 302 C R350x350 CONCR 4.33 0.0 RC Column Column
242 303 304 C R350x350 CONCR 4.33 0.0 RC Column Column
243 302 305 WF 250x125x6 STEEL 1.30 0.0 Column Bar
244 304 306 WF 250x125x6 STEEL 1.30 0.0 Column Bar
245 305 307 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
246 307 306 WF 250x125x6 STEEL 6.79 0.0 Beam_Rafte Bar
247 308 309 C R350x350 CONCR 4.33 0.0 RC Column Column
248 310 311 C R350x350 CONCR 4.33 0.0 RC Column Column
249 309 312 WF 250x125x6 STEEL 1.30 0.0 Column Bar
Quantity survey
Length Unit weight Total weight Painting area
Type Number Bar weight (kG)
(m) (kG/m) (kG) (m2)
CONCR
B R150x150 16 3.00 54.16 162.49 2600 28.80
B R150x150 8 3.15 54.16 170.62 1365 15.12
B R150x150 2 3.25 54.16 176.03 352 3.90
B R150x150 1 6.50 54.16 352.07 352 3.90
B R200x300 16 3.00 144.44 433.32 6933 48.00
B R200x300 8 3.15 144.44 454.98 3640 25.20
B R200x300 2 3.25 144.44 469.43 939 6.50
B R200x300 1 6.50 144.44 938.85 939 6.50
C R150x200 4 6.75 72.22 487.48 1950 18.90
C R150x200 1 7.90 72.22 570.53 571 5.53
C R350x350 22 4.33 294.90 1276.90 28092 133.36
Total per sections
B R150x150 27 86.20 54.16 4668.98 4669 51.72
B R200x300 27 86.20 144.44 12450.62 12451 86.20
C R150x200 5 34.90 72.22 2520.46 2520 24.43
C R350x350 22 95.26 294.90 28091.77 28092 133.36
Total 47732 295.71
STEEL
WF 250x125x6 22 1.30 29.02 37.72 830 28.60
WF 250x125x6 22 6.79 29.02 197.03 4335 149.38
Total per sections
WF 250x125x6 44 177.98 29.02 5164.61 5165 177.98
Total 5165 177.98
Loads
Combinations
- Cases: 10to25
Combination Combin
Name Analysis type ation Case nature Definition
s
type
10 (C) COMB1 (BAJA) Linear Combinati ULS dead (1+2)*1.40
11 (C) COMB2 (BAJA) Linear Combinati ULS dead (1+2)*1.20+3*1.60
12 (C) COMB3 (BAJA) Linear Combinati ULS dead (1+2)*1.20+3*1.00
13 (C) COMB4 (BAJA) Linear Combinati ULS dead (1+2)*1.20+7*0.50
14 (C) COMB5 (BAJA) Linear Combinati ULS dead (1+2)*1.20+7*1.00
15 (C) COMB6 (BAJA) Linear Combinati ULS dead (1+2)*0.90+7*1.00
16 (C) (CCOMB7 (BAJA) Linear Combinati ULS dead (1+2)*1.20+(8+3)*1.00
17 (C) (CCOMB8 (BAJA) Linear Combinati ULS dead (1+2)*1.20+(3+9)*1.00
18 (C) COMB9 (BETON Linear Combinati ULS dead (4+5)*1.40
19 (C) COMB10 (BETO Linear Combinati ULS dead (4+5)*1.20+6*1.60
20 (C) COMB11 (BETO Linear Combinati ULS dead (4+5)*1.20+6*1.00
21 (C) COMB12 (BETO Linear Combinati ULS dead (4+5)*1.20+7*0.50
22 (C) COMB13 (BETO Linear Combinati ULS dead (4+5)*1.20+7*1.00
23 (C) COMB14 (BETO Linear Combinati ULS dead (4+5)*0.90+7*1.00
24 (C) (CCOMB15 (BETO Linear Combinati ULS dead (4+5)*1.20+(8+6)*1.00
25 (C) (CCOMB16 (BETO Linear Combinati ULS dead (4+5)*1.20+(6+9)*1.00
Fx/Ax (kPa)
MAX 6220.98
Bar 214
Node 269
Case 11 (C)
MIN -722.33
Bar 263
Node 326
Case 22 (C)
View:2 - Ratio
View - Ratio
1 Level:
⦁ Name : Level +4.33
⦁ Reference level : 0.00 (m)
⦁ Fire rating : 0 (h)
⦁ Environment class : mild
2.2 Geometry:
2.2.1 Rectangular 350.00 x 350.00 (mm)
2.2.2 Height: L = 4.26 (m)
2.2.3 Slab thickness = 0.00 (m)
2.2.4 Beam height = 0.15 (m)
2.2.5 Cover = 30.00 (mm)
2.4 Loads:
0.00 0.00
COMB9 (BETON) 1.4D design 235 1.00 26.92 0.00 -0.00 -0.00 0.21
-0.08 0.09
COMB9 (BETON) 1.4D design 236 1.00 26.92 -0.00 0.00 0.00 0.21
-0.08 0.09
COMB9 (BETON) 1.4D design 241 1.00 26.69 0.00 -0.00 -0.00 -0.01
0.05 0.02
COMB9 (BETON) 1.4D design 242 1.00 26.69 -0.00 0.00 0.00 -0.01
0.05 0.02
COMB9 (BETON) 1.4D design 247 1.00 26.69 0.00 0.00 0.00 -0.01
0.06 0.03
COMB9 (BETON) 1.4D design 248 1.00 26.69 -0.00 -0.00 -0.00 -0.01
0.06 0.03
COMB9 (BETON) 1.4D design 253 1.00 26.75 0.01 0.01 0.01 -0.07
0.11 0.04
COMB9 (BETON) 1.4D design 254 1.00 26.75 -0.01 -0.01 -0.01 -0.07
0.11 0.04
COMB9 (BETON) 1.4D design 259 1.00 25.38 3.25 -1.52 1.34 2.16
-0.99 0.90
COMB9 (BETON) 1.4D design 260 1.00 25.38 -3.25 1.52 -1.34 2.16
-0.99 0.90
COMB10 (BETON) 1.2D+1.6L design 1 1.00 23.49 1.17 -0.62 0.47 -1.85
0.84 -0.77
COMB10 (BETON) 1.2D+1.6L design 2 1.00 23.49 -1.17 0.62 -0.47 -1.85
0.84 -0.77
COMB10 (BETON) 1.2D+1.6L design 205 1.00 22.93 0.01 -0.01 0.00 0.06
-0.09 -0.04
COMB10 (BETON) 1.2D+1.6L design 206 1.00 22.93 -0.01 0.01 -0.00 0.06
-0.09 -0.04
COMB10 (BETON) 1.2D+1.6L design 211 1.00 22.88 -0.00 0.00 0.00 0.01
-0.05 -0.03
COMB10 (BETON) 1.2D+1.6L design 212 1.00 22.88 0.00 -0.00 -0.00 0.01
-0.05 -0.03
COMB10 (BETON) 1.2D+1.6L design 217 1.00 22.88 -0.00 0.00 0.00 0.01
-0.04 -0.02
COMB10 (BETON) 1.2D+1.6L design 218 1.00 22.88 0.00 -0.00 -0.00 0.01
-0.04 -0.02
COMB10 (BETON) 1.2D+1.6L design 223 1.00 23.08 0.00 -0.00 -0.00 -0.18
0.07 -0.08
COMB10 (BETON) 1.2D+1.6L design 224 1.00 23.08 -0.00 0.00 0.00 -0.18
0.07 -0.08
COMB10 (BETON) 1.2D+1.6L design 229 1.00 23.28 -0.00 0.00 0.00 -0.00
0.00 0.00
COMB10 (BETON) 1.2D+1.6L design 230 1.00 23.28 0.00 -0.00 -0.00 -0.00
0.00 0.00
COMB10 (BETON) 1.2D+1.6L design 235 1.00 23.08 0.00 -0.00 -0.00 0.18
-0.07 0.08
COMB10 (BETON) 1.2D+1.6L design 236 1.00 23.08 -0.00 0.00 0.00 0.18
-0.07 0.08
COMB10 (BETON) 1.2D+1.6L design 241 1.00 22.88 0.00 -0.00 -0.00 -0.01
0.04 0.02
COMB10 (BETON) 1.2D+1.6L design 242 1.00 22.88 -0.00 0.00 0.00 -0.01
0.04 0.02
COMB10 (BETON) 1.2D+1.6L design 247 1.00 22.88 0.00 0.00 0.00 -0.01
0.05 0.03
COMB10 (BETON) 1.2D+1.6L design 248 1.00 22.88 -0.00 -0.00 -0.00 -0.01
0.05 0.03
COMB10 (BETON) 1.2D+1.6L design 253 1.00 22.92 0.01 0.01 0.01 -0.06
0.09 0.04
COMB10 (BETON) 1.2D+1.6L design 254 1.00 22.92 -0.01 -0.01 -0.01 -0.06
0.09 0.04
COMB10 (BETON) 1.2D+1.6L design 259 1.00 21.28 3.19 -1.48 1.32 1.85
-0.84 0.77
COMB10 (BETON) 1.2D+1.6L design 260 1.00 21.28 -3.19 1.48 -1.32 1.85
-0.84 0.77
COMB11 (BETON) 1.2D+1L design 1 1.00 23.49 1.17 -0.62 0.47 -1.85
0.84 -0.77
COMB11 (BETON) 1.2D+1L design 2 1.00 23.49 -1.17 0.62 -0.47 -1.85
0.84 -0.77
COMB11 (BETON) 1.2D+1L design 205 1.00 22.93 0.01 -0.01 0.00 0.06
-0.09 -0.04
COMB11 (BETON) 1.2D+1L design 206 1.00 22.93 -0.01 0.01 -0.00 0.06
-0.09 -0.04
COMB11 (BETON) 1.2D+1L design 211 1.00 22.88 -0.00 0.00 0.00 0.01
-0.05 -0.03
COMB11 (BETON) 1.2D+1L design 212 1.00 22.88 0.00 -0.00 -0.00 0.01
-0.05 -0.03
COMB11 (BETON) 1.2D+1L design 217 1.00 22.88 -0.00 0.00 0.00 0.01
Date : 30/08/23 Page : 2
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
-0.04 -0.02
COMB11 (BETON) 1.2D+1L design 218 1.00 22.88 0.00 -0.00 -0.00 0.01
-0.04 -0.02
COMB11 (BETON) 1.2D+1L design 223 1.00 23.08 0.00 -0.00 -0.00 -0.18
0.07 -0.08
COMB11 (BETON) 1.2D+1L design 224 1.00 23.08 -0.00 0.00 0.00 -0.18
0.07 -0.08
COMB11 (BETON) 1.2D+1L design 229 1.00 23.28 -0.00 0.00 0.00 -0.00
0.00 0.00
COMB11 (BETON) 1.2D+1L design 230 1.00 23.28 0.00 -0.00 -0.00 -0.00
0.00 0.00
COMB11 (BETON) 1.2D+1L design 235 1.00 23.08 0.00 -0.00 -0.00 0.18
-0.07 0.08
COMB11 (BETON) 1.2D+1L design 236 1.00 23.08 -0.00 0.00 0.00 0.18
-0.07 0.08
COMB11 (BETON) 1.2D+1L design 241 1.00 22.88 0.00 -0.00 -0.00 -0.01
0.04 0.02
COMB11 (BETON) 1.2D+1L design 242 1.00 22.88 -0.00 0.00 0.00 -0.01
0.04 0.02
COMB11 (BETON) 1.2D+1L design 247 1.00 22.88 0.00 0.00 0.00 -0.01
0.05 0.03
COMB11 (BETON) 1.2D+1L design 248 1.00 22.88 -0.00 -0.00 -0.00 -0.01
0.05 0.03
COMB11 (BETON) 1.2D+1L design 253 1.00 22.92 0.01 0.01 0.01 -0.06
0.09 0.04
COMB11 (BETON) 1.2D+1L design 254 1.00 22.92 -0.01 -0.01 -0.01 -0.06
0.09 0.04
COMB11 (BETON) 1.2D+1L design 259 1.00 21.46 3.04 -1.42 1.26 1.85
-0.84 0.77
COMB11 (BETON) 1.2D+1L design 260 1.00 21.46 -3.04 1.42 -1.26 1.85
-0.84 0.77
COMB12 (BETON) 1.2D+0.5W design 1 1.00 23.17 0.88 2.07 1.41 -1.85
0.84 -0.77
COMB12 (BETON) 1.2D+0.5W design 2 1.00 23.59 -1.52 3.01 1.20 -1.85
0.84 -0.77
COMB12 (BETON) 1.2D+0.5W design 205 1.00 23.08 0.35 4.65 2.96 0.06
-0.09 -0.04
COMB12 (BETON) 1.2D+0.5W design 206 1.00 21.81 1.09 2.31 1.82 0.06
-0.09 -0.04
COMB12 (BETON) 1.2D+0.5W design 211 1.00 23.03 0.26 5.09 3.22 0.01
-0.05 -0.03
COMB12 (BETON) 1.2D+0.5W design 212 1.00 21.77 1.12 2.53 1.97 0.01
-0.05 -0.03
COMB12 (BETON) 1.2D+0.5W design 217 1.00 23.02 0.27 5.11 3.24 0.01
-0.04 -0.02
COMB12 (BETON) 1.2D+0.5W design 218 1.00 21.77 1.12 2.57 1.99 0.01
-0.04 -0.02
COMB12 (BETON) 1.2D+0.5W design 223 1.00 23.22 0.27 5.12 3.24 -0.18
0.07 -0.08
COMB12 (BETON) 1.2D+0.5W design 224 1.00 21.97 1.12 2.57 1.99 -0.18
0.07 -0.08
COMB12 (BETON) 1.2D+0.5W design 229 1.00 23.43 0.27 5.11 3.24 -0.00
0.00 0.00
COMB12 (BETON) 1.2D+0.5W design 230 1.00 22.17 1.12 2.57 1.99 -0.00
0.00 0.00
COMB12 (BETON) 1.2D+0.5W design 235 1.00 23.22 0.27 5.12 3.24 0.18
-0.07 0.08
COMB12 (BETON) 1.2D+0.5W design 236 1.00 21.97 1.12 2.57 1.99 0.18
-0.07 0.08
COMB12 (BETON) 1.2D+0.5W design 241 1.00 23.02 0.27 5.11 3.24 -0.01
0.04 0.02
COMB12 (BETON) 1.2D+0.5W design 242 1.00 21.77 1.12 2.57 1.99 -0.01
0.04 0.02
COMB12 (BETON) 1.2D+0.5W design 247 1.00 23.03 0.27 5.09 3.22 -0.01
0.05 0.03
COMB12 (BETON) 1.2D+0.5W design 248 1.00 21.77 1.12 2.54 1.97 -0.01
0.05 0.03
COMB12 (BETON) 1.2D+0.5W design 253 1.00 23.08 0.35 4.69 2.98 -0.06
0.09 0.04
COMB12 (BETON) 1.2D+0.5W design 254 1.00 21.81 1.08 2.33 1.83 -0.06
0.09 0.04
COMB12 (BETON) 1.2D+0.5W design 259 1.00 21.34 2.53 1.53 1.93 1.85
-0.84 0.77
COMB12 (BETON) 1.2D+0.5W design 260 1.00 21.87 -3.22 3.90 1.56 1.85
-0.84 0.77
COMB13 (BETON) 1.2D+1W design 1 1.00 22.84 0.60 4.75 2.85 -1.84
0.84 -0.77
COMB13 (BETON) 1.2D+1W design 2 1.00 23.68 -1.86 5.40 2.50 -1.85
Date : 30/08/23 Page : 3
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
0.84 -0.77
COMB13 (BETON) 1.2D+1W design 205 1.00 23.23 0.70 9.30 5.91 0.06
-0.09 -0.04
COMB13 (BETON) 1.2D+1W design 206 1.00 20.70 2.18 4.60 3.64 0.06
-0.09 -0.04
COMB13 (BETON) 1.2D+1W design 211 1.00 23.17 0.53 10.18 6.44 0.01
-0.05 -0.03
COMB13 (BETON) 1.2D+1W design 212 1.00 20.67 2.25 5.07 3.94 0.01
-0.05 -0.03
COMB13 (BETON) 1.2D+1W design 217 1.00 23.17 0.54 10.23 6.48 0.01
-0.04 -0.02
COMB13 (BETON) 1.2D+1W design 218 1.00 20.66 2.24 5.14 3.98 0.01
-0.04 -0.02
COMB13 (BETON) 1.2D+1W design 223 1.00 23.37 0.54 10.23 6.48 -0.18
0.07 -0.08
COMB13 (BETON) 1.2D+1W design 224 1.00 20.87 2.24 5.14 3.98 -0.18
0.07 -0.08
COMB13 (BETON) 1.2D+1W design 229 1.00 23.57 0.54 10.23 6.48 -0.00
0.00 0.00
COMB13 (BETON) 1.2D+1W design 230 1.00 21.07 2.24 5.14 3.98 -0.00
0.00 0.00
COMB13 (BETON) 1.2D+1W design 235 1.00 23.37 0.54 10.23 6.48 0.18
-0.07 0.08
COMB13 (BETON) 1.2D+1W design 236 1.00 20.87 2.24 5.14 3.98 0.18
-0.07 0.08
COMB13 (BETON) 1.2D+1W design 241 1.00 23.17 0.54 10.23 6.48 -0.01
0.04 0.02
COMB13 (BETON) 1.2D+1W design 242 1.00 20.66 2.24 5.14 3.98 -0.01
0.04 0.02
COMB13 (BETON) 1.2D+1W design 247 1.00 23.17 0.53 10.18 6.44 -0.01
0.05 0.03
COMB13 (BETON) 1.2D+1W design 248 1.00 20.67 2.25 5.08 3.94 -0.01
0.05 0.03
COMB13 (BETON) 1.2D+1W design 253 1.00 23.23 0.70 9.37 5.96 -0.06
0.09 0.04
COMB13 (BETON) 1.2D+1W design 254 1.00 20.70 2.18 4.66 3.67 -0.06
0.09 0.04
COMB13 (BETON) 1.2D+1W design 259 1.00 20.92 2.27 4.36 3.15 1.84
-0.84 0.77
COMB13 (BETON) 1.2D+1W design 260 1.00 21.98 -3.65 6.49 2.60 1.85
-0.84 0.77
COMB14 (BETON) 0.9D+1W design 1 1.00 16.96 0.30 4.91 2.85 -1.38
0.63 -0.58
COMB14 (BETON) 0.9D+1W design 2 1.00 17.80 -1.56 5.25 2.52 -1.38
0.63 -0.58
COMB14 (BETON) 0.9D+1W design 205 1.00 17.50 0.70 9.30 5.91 0.04
-0.07 -0.03
COMB14 (BETON) 0.9D+1W design 206 1.00 14.97 2.19 4.60 3.64 0.05
-0.07 -0.03
COMB14 (BETON) 0.9D+1W design 211 1.00 17.45 0.53 10.18 6.44 0.01
-0.04 -0.02
COMB14 (BETON) 0.9D+1W design 212 1.00 14.95 2.25 5.07 3.94 0.01
-0.04 -0.02
COMB14 (BETON) 0.9D+1W design 217 1.00 17.45 0.54 10.23 6.48 0.01
-0.03 -0.01
COMB14 (BETON) 0.9D+1W design 218 1.00 14.94 2.24 5.14 3.98 0.01
-0.03 -0.01
COMB14 (BETON) 0.9D+1W design 223 1.00 17.60 0.54 10.23 6.48 -0.13
0.05 -0.06
COMB14 (BETON) 0.9D+1W design 224 1.00 15.10 2.24 5.14 3.98 -0.14
0.06 -0.06
COMB14 (BETON) 0.9D+1W design 229 1.00 17.75 0.54 10.23 6.48 0.00
-0.00 -0.00
COMB14 (BETON) 0.9D+1W design 230 1.00 15.25 2.24 5.14 3.98 -0.00
0.00 0.00
COMB14 (BETON) 0.9D+1W design 235 1.00 17.60 0.54 10.23 6.48 0.13
-0.05 0.06
COMB14 (BETON) 0.9D+1W design 236 1.00 15.10 2.24 5.14 3.98 0.13
-0.05 0.06
COMB14 (BETON) 0.9D+1W design 241 1.00 17.45 0.54 10.23 6.48 -0.01
0.03 0.01
COMB14 (BETON) 0.9D+1W design 242 1.00 14.94 2.24 5.14 3.98 -0.01
0.03 0.01
COMB14 (BETON) 0.9D+1W design 247 1.00 17.45 0.53 10.18 6.44 -0.01
0.04 0.02
COMB14 (BETON) 0.9D+1W design 248 1.00 14.95 2.25 5.08 3.94 -0.01
0.04 0.02
COMB14 (BETON) 0.9D+1W design 253 1.00 17.50 0.69 9.37 5.96 -0.04
Date : 30/08/23 Page : 4
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
0.07 0.03
COMB14 (BETON) 0.9D+1W design 254 1.00 14.97 2.18 4.66 3.67 -0.04
0.07 0.03
COMB14 (BETON) 0.9D+1W design 259 1.00 15.48 1.58 4.69 3.13 1.38
-0.63 0.58
COMB14 (BETON) 0.9D+1W design 260 1.00 16.54 -2.96 6.17 2.52 1.39
-0.63 0.58
COMB15 (BETON) 1.2D+1Ex+1L design 1 1.00 22.46 -1.01 7.25 3.95 -1.85
0.85 -0.77
COMB15 (BETON) 1.2D+1Ex+1L design 2 1.00 24.53 -3.35 8.49 3.75 -1.85
0.84 -0.77
COMB15 (BETON) 1.2D+1Ex+1L design 205 1.00 22.67 -0.70 6.84 3.82 0.06
-0.09 -0.04
COMB15 (BETON) 1.2D+1Ex+1L design 206 1.00 23.19 -0.72 6.85 3.82 0.06
-0.09 -0.04
COMB15 (BETON) 1.2D+1Ex+1L design 211 1.00 22.62 -0.70 6.79 3.79 0.01
-0.05 -0.03
COMB15 (BETON) 1.2D+1Ex+1L design 212 1.00 23.14 -0.69 6.79 3.79 0.01
-0.05 -0.03
COMB15 (BETON) 1.2D+1Ex+1L design 217 1.00 22.62 -0.70 6.79 3.80 0.01
-0.04 -0.02
COMB15 (BETON) 1.2D+1Ex+1L design 218 1.00 23.13 -0.70 6.79 3.80 0.01
-0.04 -0.02
COMB15 (BETON) 1.2D+1Ex+1L design 223 1.00 22.82 -0.70 6.87 3.84 -0.18
0.07 -0.08
COMB15 (BETON) 1.2D+1Ex+1L design 224 1.00 23.34 -0.70 6.87 3.84 -0.18
0.07 -0.08
COMB15 (BETON) 1.2D+1Ex+1L design 229 1.00 22.99 -0.70 7.17 4.02 -0.00
0.00 0.00
COMB15 (BETON) 1.2D+1Ex+1L design 230 1.00 23.57 -0.70 7.17 4.02 -0.00
0.00 0.00
COMB15 (BETON) 1.2D+1Ex+1L design 235 1.00 22.78 -0.70 7.21 4.04 0.18
-0.07 0.08
COMB15 (BETON) 1.2D+1Ex+1L design 236 1.00 23.37 -0.70 7.21 4.04 0.18
-0.07 0.08
COMB15 (BETON) 1.2D+1Ex+1L design 241 1.00 22.58 -0.70 7.19 4.03 -0.01
0.04 0.02
COMB15 (BETON) 1.2D+1Ex+1L design 242 1.00 23.17 -0.70 7.19 4.03 -0.01
0.04 0.02
COMB15 (BETON) 1.2D+1Ex+1L design 247 1.00 22.59 -0.70 7.18 4.03 -0.01
0.05 0.03
COMB15 (BETON) 1.2D+1Ex+1L design 248 1.00 23.17 -0.70 7.18 4.03 -0.01
0.05 0.03
COMB15 (BETON) 1.2D+1Ex+1L design 253 1.00 22.63 -0.69 7.13 4.00 -0.06
0.09 0.04
COMB15 (BETON) 1.2D+1Ex+1L design 254 1.00 23.22 -0.71 7.12 3.99 -0.06
0.09 0.04
COMB15 (BETON) 1.2D+1Ex+1L design 259 1.00 20.47 0.89 6.22 4.09 1.85
-0.84 0.77
COMB15 (BETON) 1.2D+1Ex+1L design 260 1.00 22.44 -5.19 9.06 3.62 1.85
-0.85 0.77
COMB16 (BETON) 1.2D+1Ey+1L design 1 1.00 24.13 1.20 -0.64 0.48 -2.13
8.04 3.97
COMB16 (BETON) 1.2D+1Ey+1L design 2 1.00 24.13 -1.20 0.64 -0.48 -2.13
8.04 3.97
COMB16 (BETON) 1.2D+1Ey+1L design 205 1.00 22.91 -0.12 0.22 0.09 -0.81
7.38 4.10
COMB16 (BETON) 1.2D+1Ey+1L design 206 1.00 22.91 0.12 -0.22 -0.09 -0.81
7.38 4.10
COMB16 (BETON) 1.2D+1Ey+1L design 211 1.00 22.88 0.00 0.00 0.00 -0.84
7.39 4.10
COMB16 (BETON) 1.2D+1Ey+1L design 212 1.00 22.88 -0.00 -0.00 -0.00 -0.84
7.39 4.10
COMB16 (BETON) 1.2D+1Ey+1L design 217 1.00 22.88 0.00 -0.00 -0.00 -0.84
7.40 4.10
COMB16 (BETON) 1.2D+1Ey+1L design 218 1.00 22.88 -0.00 0.00 0.00 -0.84
7.40 4.10
COMB16 (BETON) 1.2D+1Ey+1L design 223 1.00 23.02 -0.01 0.01 0.00 -0.99
7.48 4.09
COMB16 (BETON) 1.2D+1Ey+1L design 224 1.00 23.02 0.01 -0.01 -0.00 -0.99
7.48 4.09
COMB16 (BETON) 1.2D+1Ey+1L design 229 1.00 23.28 -0.00 0.00 0.00 -0.77
7.38 4.12
COMB16 (BETON) 1.2D+1Ey+1L design 230 1.00 23.28 0.00 -0.00 -0.00 -0.77
7.38 4.12
COMB16 (BETON) 1.2D+1Ey+1L design 235 1.00 23.13 0.01 -0.01 -0.00 -0.63
7.32 4.14
COMB16 (BETON) 1.2D+1Ey+1L design 236 1.00 23.13 -0.01 0.01 0.00 -0.63
Date : 30/08/23 Page : 5
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
7.32 4.14
COMB16 (BETON) 1.2D+1Ey+1L design 241 1.00 22.87 -0.00 0.00 0.00 -0.86
7.46 4.13
COMB16 (BETON) 1.2D+1Ey+1L design 242 1.00 22.87 0.00 -0.00 -0.00 -0.86
7.46 4.13
COMB16 (BETON) 1.2D+1Ey+1L design 247 1.00 22.88 -0.00 0.00 -0.00 -0.86
7.48 4.14
COMB16 (BETON) 1.2D+1Ey+1L design 248 1.00 22.88 0.00 -0.00 0.00 -0.86
7.48 4.14
COMB16 (BETON) 1.2D+1Ey+1L design 253 1.00 22.93 0.11 -0.16 -0.06 -0.91
7.53 4.15
COMB16 (BETON) 1.2D+1Ey+1L design 254 1.00 22.93 -0.11 0.16 0.06 -0.91
7.53 4.15
COMB16 (BETON) 1.2D+1Ey+1L design 259 1.00 20.82 3.02 -1.40 1.25 1.34
6.43 4.39
COMB16 (BETON) 1.2D+1Ey+1L design 260 1.00 20.82 -3.02 1.40 -1.25 1.34
6.43 4.39
f - load factor
Design forces:
Lower node
N = 17.45 (kN) My = 10.23 (kN*m) Mz = 0.03 (kN*m)
Non-sway structure
lu (m) k k*lu (m)
4.33 1.00 4.33
k*luy/ry = 42.86 > 22.00 Slender column (10-7)
2.5.2 Reinforcement:
3 Material survey:
⦁ Concrete volume = 11.06 (m3)
⦁ Formwork = 126.43 (m2)
1 Ø16 Grade
l=4.22
420 1 4.23 Grade 420 8
29
2 Ø10 Grade
l=1.30
300 T1 Grade 300 27
29
11
A
4.25
4.11
26x15
A-A
Ø10 Grade 300
2 l=1.30
e=15
35
0 Ø16 Grade 420
l=4.22 1
10
35
35
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 350x350 View scale 1/33
Section scale 1/10 Page 1
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
1 Level:
⦁ Name : Level +7.90
⦁ Reference level : 0.00 (m)
⦁ Fire rating : 0 (h)
⦁ Environment class : mild
2.2 Geometry:
2.2.1 Rectangular 150.00 x 200.00 (mm)
2.2.2 Height: L = 7.75 (m)
2.2.3 Slab thickness = 0.00 (m)
2.2.4 Beam height = 0.00 (m)
2.2.5 Cover = 30.00 (mm)
2.4 Loads:
Design forces:
Cross-section in the middle of the column
N = 17.04 (kN) My = 0.30 (kN*m) Mz = -0.01 (kN*m)
Non-sway structure
lu (m) k k*lu (m)
7.90 1.00 7.90
k*luy/ry = 136.83 > 34.00 Slender column (10-7)
2.5.2 Reinforcement:
3 Material survey:
⦁ Concrete volume = 0.23 (m3)
⦁ Formwork = 5.43 (m2)
17
2 60Ø10 Grade 300 l=72
12
11
A
7.75
7.75
59x13
A-A
4Ø13 Grade 420
1 l=7.74
20
60Ø10 Grade 300
4
l=72 2
15 e=13
15
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 150x200 View scale 1.25cm/m
Section scale 9.36cm/m Page 1
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
1.1.1 Assumptions
1.1.2 Geometry:
1.1.3 Materials
1.1.4 Loads:
Foundation loads:
Case Nature Group N Fx Fy Mx My
(kN) (kN) (kN) (kN*m) (kN*m)
COMB9 (BETON) 1.4D design ---- 47.71 -0.48 0.73 3.97 4.74
COMB10 (BETON) 1.2D+1.6L design ---- 45.82 -0.41 0.62 4.60 5.38
COMB11 (BETON) 1.2D+1L design ---- 43.97 -0.41 0.62 4.15 4.89
COMB12 (BETON) 1.2D+0.5W design ---- 40.57 0.54 0.62 3.40 6.75
COMB13 (BETON) 1.2D+1W design ---- 40.24 1.50 0.62 3.41 9.43
COMB14 (BETON) 0.9D+1W design ---- 30.02 1.60 0.46 2.56 8.42
Date : 30/08/23 Page : 1
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.94 1.91 0.62 4.15 12.76
COMB16 (BETON) 1.2D+1Ey+1L design ---- 44.61 -0.43 2.35 -3.04 4.86
COMB9 (BETON) 1.4D design ---- 47.71 0.48 0.73 3.97 -4.74
COMB10 (BETON) 1.2D+1.6L design ---- 45.82 0.41 0.62 4.60 -5.38
COMB11 (BETON) 1.2D+1L design ---- 43.97 0.41 0.62 4.15 -4.89
COMB12 (BETON) 1.2D+0.5W design ---- 40.99 1.04 0.62 3.40 -1.67
COMB13 (BETON) 1.2D+1W design ---- 41.08 1.68 0.62 3.40 0.72
COMB14 (BETON) 0.9D+1W design ---- 30.86 1.57 0.47 2.55 1.74
COMB15 (BETON) 1.2D+1Ex+1L design ---- 45.01 2.74 0.62 4.15 2.98
COMB16 (BETON) 1.2D+1Ey+1L design ---- 44.61 0.43 2.35 -3.04 -4.86
COMB9 (BETON) 1.4D design ---- 46.56 -0.00 -0.04 0.11 -0.01
COMB10 (BETON) 1.2D+1.6L design ---- 44.71 -0.00 -0.03 0.09 -0.01
COMB11 (BETON) 1.2D+1L design ---- 42.91 -0.00 -0.03 0.09 -0.01
COMB12 (BETON) 1.2D+0.5W design ---- 40.06 1.26 -0.03 0.09 4.65
COMB13 (BETON) 1.2D+1W design ---- 40.21 2.53 -0.03 0.09 9.30
COMB14 (BETON) 0.9D+1W design ---- 30.24 2.53 -0.03 0.07 9.30
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.65 1.74 -0.03 0.09 6.84
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.89 0.08 1.89 -7.38 0.22
COMB9 (BETON) 1.4D design ---- 46.56 0.00 -0.04 0.11 0.01
COMB10 (BETON) 1.2D+1.6L design ---- 44.71 0.00 -0.03 0.09 0.01
COMB11 (BETON) 1.2D+1L design ---- 42.91 0.00 -0.03 0.09 0.01
COMB12 (BETON) 1.2D+0.5W design ---- 38.79 0.28 -0.03 0.09 2.31
COMB13 (BETON) 1.2D+1W design ---- 37.68 0.56 -0.04 0.09 4.60
COMB14 (BETON) 0.9D+1W design ---- 27.70 0.56 -0.03 0.07 4.60
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.16 1.75 -0.04 0.09 6.85
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.89 -0.08 1.89 -7.38 -0.22
COMB9 (BETON) 1.4D design ---- 46.50 0.00 -0.02 0.06 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.66 0.00 -0.01 0.05 0.00
COMB11 (BETON) 1.2D+1L design ---- 42.86 0.00 -0.01 0.05 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.01 1.38 -0.01 0.05 5.09
COMB13 (BETON) 1.2D+1W design ---- 40.15 2.77 -0.02 0.05 10.18
COMB14 (BETON) 0.9D+1W design ---- 30.19 2.77 -0.01 0.04 10.18
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.60 1.73 -0.01 0.05 6.79
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.86 -0.00 1.90 -7.39 0.00
COMB9 (BETON) 1.4D design ---- 46.50 -0.00 -0.02 0.06 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.66 -0.00 -0.01 0.05 -0.00
COMB11 (BETON) 1.2D+1L design ---- 42.86 -0.00 -0.01 0.05 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 38.75 0.33 -0.01 0.05 2.53
COMB13 (BETON) 1.2D+1W design ---- 37.64 0.65 -0.01 0.05 5.07
COMB14 (BETON) 0.9D+1W design ---- 27.68 0.65 -0.01 0.04 5.07
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.12 1.73 -0.01 0.05 6.79
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.86 0.00 1.90 -7.39 -0.00
COMB9 (BETON) 1.4D design ---- 46.50 0.00 -0.01 0.04 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.65 0.00 -0.01 0.04 0.00
COMB11 (BETON) 1.2D+1L design ---- 42.85 0.00 -0.01 0.04 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.00 1.39 -0.01 0.04 5.11
COMB13 (BETON) 1.2D+1W design ---- 40.15 2.78 -0.01 0.04 10.23
COMB14 (BETON) 0.9D+1W design ---- 30.18 2.78 -0.01 0.03 10.23
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.60 1.73 -0.01 0.04 6.79
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.86 -0.00 1.90 -7.40 -0.00
COMB9 (BETON) 1.4D design ---- 46.50 -0.00 -0.01 0.04 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.65 -0.00 -0.01 0.04 -0.00
COMB11 (BETON) 1.2D+1L design ---- 42.85 -0.00 -0.01 0.04 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 38.75 0.33 -0.01 0.04 2.57
COMB13 (BETON) 1.2D+1W design ---- 37.64 0.67 -0.01 0.04 5.14
COMB14 (BETON) 0.9D+1W design ---- 27.68 0.67 -0.01 0.03 5.14
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.11 1.73 -0.01 0.04 6.79
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.86 0.00 1.90 -7.40 0.00
COMB9 (BETON) 1.4D design ---- 47.23 -0.00 0.07 0.42 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 45.40 -0.00 0.06 0.48 -0.00
COMB11 (BETON) 1.2D+1L design ---- 43.56 -0.00 0.06 0.44 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.63 1.39 0.06 0.36 5.12
COMB13 (BETON) 1.2D+1W design ---- 40.77 2.78 0.06 0.36 10.23
COMB14 (BETON) 0.9D+1W design ---- 30.65 2.78 0.04 0.27 10.23
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.30 1.75 0.06 0.44 6.87
COMB16 (BETON) 1.2D+1Ey+1L design ---- 43.50 0.00 1.96 -6.97 0.01
COMB9 (BETON) 1.4D design ---- 47.23 0.00 0.07 0.42 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 45.40 0.00 0.06 0.48 0.00
COMB11 (BETON) 1.2D+1L design ---- 43.56 0.00 0.06 0.44 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 39.37 0.34 0.06 0.36 2.57
COMB13 (BETON) 1.2D+1W design ---- 38.27 0.67 0.06 0.36 5.14
COMB14 (BETON) 0.9D+1W design ---- 28.15 0.67 0.04 0.27 5.14
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.82 1.75 0.06 0.44 6.87
COMB16 (BETON) 1.2D+1Ey+1L design ---- 43.50 -0.00 1.96 -6.97 -0.01
COMB9 (BETON) 1.4D design ---- 47.96 0.00 0.00 -0.00 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 46.15 0.00 0.00 -0.00 0.00
COMB11 (BETON) 1.2D+1L design ---- 44.26 0.00 0.00 -0.00 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 41.25 1.39 0.00 -0.00 5.11
Date : 30/08/23 Page : 2
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
COMB13 (BETON) 1.2D+1W design ---- 41.40 2.78 0.00 -0.00 10.23
COMB14 (BETON) 0.9D+1W design ---- 31.12 2.78 -0.00 0.00 10.23
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.97 1.82 0.00 -0.00 7.17
COMB16 (BETON) 1.2D+1Ey+1L design ---- 44.26 0.00 1.88 -7.38 0.00
COMB9 (BETON) 1.4D design ---- 47.96 -0.00 0.00 -0.00 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 46.15 -0.00 0.00 -0.00 -0.00
COMB11 (BETON) 1.2D+1L design ---- 44.26 -0.00 0.00 -0.00 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.00 0.34 0.00 -0.00 2.57
COMB13 (BETON) 1.2D+1W design ---- 38.90 0.67 0.00 -0.00 5.14
COMB14 (BETON) 0.9D+1W design ---- 28.62 0.67 0.00 -0.00 5.14
COMB15 (BETON) 1.2D+1Ex+1L design ---- 44.55 1.82 0.00 -0.00 7.17
COMB16 (BETON) 1.2D+1Ey+1L design ---- 44.26 -0.00 1.88 -7.38 -0.00
COMB9 (BETON) 1.4D design ---- 47.23 -0.00 -0.07 -0.42 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 45.40 -0.00 -0.06 -0.49 -0.00
COMB11 (BETON) 1.2D+1L design ---- 43.56 -0.00 -0.06 -0.44 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.63 1.39 -0.06 -0.36 5.12
COMB13 (BETON) 1.2D+1W design ---- 40.77 2.78 -0.06 -0.36 10.23
COMB14 (BETON) 0.9D+1W design ---- 30.65 2.78 -0.04 -0.27 10.23
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.26 1.83 -0.06 -0.44 7.21
COMB16 (BETON) 1.2D+1Ey+1L design ---- 43.61 -0.00 1.84 -7.84 -0.01
COMB9 (BETON) 1.4D design ---- 47.23 0.00 -0.07 -0.42 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 45.40 0.00 -0.06 -0.49 0.00
COMB11 (BETON) 1.2D+1L design ---- 43.56 0.00 -0.06 -0.44 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 39.37 0.34 -0.06 -0.36 2.57
COMB13 (BETON) 1.2D+1W design ---- 38.27 0.67 -0.06 -0.36 5.14
COMB14 (BETON) 0.9D+1W design ---- 28.15 0.67 -0.04 -0.27 5.14
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.85 1.83 -0.06 -0.44 7.21
COMB16 (BETON) 1.2D+1Ey+1L design ---- 43.61 0.00 1.84 -7.84 0.01
COMB9 (BETON) 1.4D design ---- 46.50 -0.00 0.01 -0.05 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.65 -0.00 0.01 -0.04 -0.00
COMB11 (BETON) 1.2D+1L design ---- 42.85 -0.00 0.01 -0.04 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.00 1.39 0.01 -0.04 5.11
COMB13 (BETON) 1.2D+1W design ---- 40.15 2.78 0.01 -0.04 10.23
COMB14 (BETON) 0.9D+1W design ---- 30.18 2.78 0.01 -0.03 10.23
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.56 1.82 0.01 -0.04 7.19
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.85 0.00 1.92 -7.46 0.00
COMB9 (BETON) 1.4D design ---- 46.50 0.00 0.01 -0.05 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.65 0.00 0.01 -0.04 0.00
COMB11 (BETON) 1.2D+1L design ---- 42.85 0.00 0.01 -0.04 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 38.75 0.34 0.01 -0.04 2.57
COMB13 (BETON) 1.2D+1W design ---- 37.64 0.67 0.01 -0.04 5.14
COMB14 (BETON) 0.9D+1W design ---- 27.68 0.67 0.01 -0.03 5.14
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.15 1.82 0.01 -0.04 7.19
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.85 -0.00 1.92 -7.46 -0.00
COMB9 (BETON) 1.4D design ---- 46.50 0.00 0.02 -0.06 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.66 -0.00 0.02 -0.05 0.00
COMB11 (BETON) 1.2D+1L design ---- 42.86 -0.00 0.02 -0.05 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 40.01 1.39 0.02 -0.05 5.09
COMB13 (BETON) 1.2D+1W design ---- 40.15 2.77 0.02 -0.05 10.18
COMB14 (BETON) 0.9D+1W design ---- 30.19 2.77 0.01 -0.04 10.18
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.57 1.82 0.02 -0.05 7.18
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.86 0.00 1.92 -7.48 0.00
COMB9 (BETON) 1.4D design ---- 46.50 -0.00 0.02 -0.06 -0.00
COMB10 (BETON) 1.2D+1.6L design ---- 44.66 0.00 0.02 -0.05 -0.00
COMB11 (BETON) 1.2D+1L design ---- 42.86 0.00 0.02 -0.05 -0.00
COMB12 (BETON) 1.2D+0.5W design ---- 38.75 0.33 0.02 -0.05 2.54
COMB13 (BETON) 1.2D+1W design ---- 37.65 0.65 0.01 -0.05 5.08
COMB14 (BETON) 0.9D+1W design ---- 27.68 0.65 0.01 -0.04 5.08
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.15 1.82 0.01 -0.05 7.18
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.86 -0.00 1.92 -7.48 -0.00
COMB9 (BETON) 1.4D design ---- 46.55 -0.00 0.04 -0.11 0.01
COMB10 (BETON) 1.2D+1.6L design ---- 44.70 -0.00 0.03 -0.09 0.01
COMB11 (BETON) 1.2D+1L design ---- 42.90 -0.00 0.03 -0.09 0.01
COMB12 (BETON) 1.2D+0.5W design ---- 40.06 1.27 0.03 -0.09 4.69
COMB13 (BETON) 1.2D+1W design ---- 40.21 2.55 0.03 -0.09 9.37
COMB14 (BETON) 0.9D+1W design ---- 30.24 2.55 0.03 -0.07 9.37
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.61 1.81 0.03 -0.09 7.13
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.91 -0.06 1.95 -7.53 -0.16
COMB9 (BETON) 1.4D design ---- 46.55 0.00 0.04 -0.11 -0.01
COMB10 (BETON) 1.2D+1.6L design ---- 44.70 0.00 0.03 -0.09 -0.01
COMB11 (BETON) 1.2D+1L design ---- 42.90 0.00 0.03 -0.09 -0.01
COMB12 (BETON) 1.2D+0.5W design ---- 38.79 0.29 0.03 -0.09 2.33
COMB13 (BETON) 1.2D+1W design ---- 37.68 0.57 0.04 -0.09 4.66
COMB14 (BETON) 0.9D+1W design ---- 27.70 0.57 0.03 -0.07 4.66
COMB15 (BETON) 1.2D+1Ex+1L design ---- 43.19 1.81 0.03 -0.09 7.12
COMB16 (BETON) 1.2D+1Ey+1L design ---- 42.91 0.06 1.95 -7.53 0.16
COMB9 (BETON) 1.4D design ---- 45.68 -1.10 -0.73 -3.97 3.94
COMB10 (BETON) 1.2D+1.6L design ---- 43.61 -1.08 -0.62 -4.60 4.52
Date : 30/08/23 Page : 3
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
COMB11 (BETON) 1.2D+1L design ---- 41.94 -1.03 -0.62 -4.15 4.09
COMB12 (BETON) 1.2D+0.5W design ---- 38.74 0.04 -0.62 -3.40 6.21
COMB13 (BETON) 1.2D+1W design ---- 38.33 1.02 -0.62 -3.40 9.04
COMB14 (BETON) 0.9D+1W design ---- 28.54 1.26 -0.46 -2.55 8.20
COMB15 (BETON) 1.2D+1Ex+1L design ---- 40.95 1.23 -0.62 -4.15 11.73
COMB16 (BETON) 1.2D+1Ey+1L design ---- 41.30 -1.02 1.18 -11.42 4.11
COMB9 (BETON) 1.4D design ---- 45.68 1.10 -0.73 -3.97 -3.94
COMB10 (BETON) 1.2D+1.6L design ---- 43.61 1.08 -0.62 -4.60 -4.52
COMB11 (BETON) 1.2D+1L design ---- 41.94 1.03 -0.62 -4.15 -4.09
COMB12 (BETON) 1.2D+0.5W design ---- 39.27 1.64 -0.62 -3.40 -0.78
COMB13 (BETON) 1.2D+1W design ---- 39.39 2.34 -0.62 -3.40 1.81
COMB14 (BETON) 0.9D+1W design ---- 29.60 2.11 -0.47 -2.55 2.66
COMB15 (BETON) 1.2D+1Ex+1L design ---- 42.92 3.29 -0.62 -4.15 3.55
COMB16 (BETON) 1.2D+1Ey+1L design ---- 41.30 1.02 1.18 -11.42 -4.11
Backfill loads:
Case Nature Q1
(kN/m2)
57/ ULS : COMB9 (BETON) 1.4D N=46.50 Mx=0.04 My=-0.00 Fx=-0.00 Fy=-0.01
58/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=0.04 My=-0.00 Fx=-0.00 Fy=-0.01
59/ ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=0.04 My=-0.00 Fx=-0.00 Fy=-0.01
60/ ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=0.04 My=2.57 Fx=0.33 Fy=-0.01
61/ ULS : COMB13 (BETON) 1.2D+1W N=37.64 Mx=0.04 My=5.14 Fx=0.67 Fy=-0.01
62/ ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=0.03 My=5.14 Fx=0.67 Fy=-0.01
63/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.11 Mx=0.04 My=6.79 Fx=1.73 Fy=-0.01
64/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.40 My=0.00 Fx=0.00 Fy=1.90
65/ ULS : COMB9 (BETON) 1.4D N=47.23 Mx=0.42 My=-0.00 Fx=-0.00 Fy=0.07
66/ ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=0.48 My=-0.00 Fx=-0.00 Fy=0.06
67/ ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=0.44 My=-0.00 Fx=-0.00 Fy=0.06
68/ ULS : COMB12 (BETON) 1.2D+0.5W N=40.63 Mx=0.36 My=5.12 Fx=1.39 Fy=0.06
69/ ULS : COMB13 (BETON) 1.2D+1W N=40.77 Mx=0.36 My=10.23 Fx=2.78 Fy=0.06
70/ ULS : COMB14 (BETON) 0.9D+1W N=30.65 Mx=0.27 My=10.23 Fx=2.78 Fy=0.04
71/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.30 Mx=0.44 My=6.87 Fx=1.75 Fy=0.06
72/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.50 Mx=-6.97 My=0.01 Fx=0.00 Fy=1.96
73/ ULS : COMB9 (BETON) 1.4D N=47.23 Mx=0.42 My=0.00 Fx=0.00 Fy=0.07
74/ ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=0.48 My=0.00 Fx=0.00 Fy=0.06
75/ ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=0.44 My=0.00 Fx=0.00 Fy=0.06
76/ ULS : COMB12 (BETON) 1.2D+0.5W N=39.37 Mx=0.36 My=2.57 Fx=0.34 Fy=0.06
77/ ULS : COMB13 (BETON) 1.2D+1W N=38.27 Mx=0.36 My=5.14 Fx=0.67 Fy=0.06
78/ ULS : COMB14 (BETON) 0.9D+1W N=28.15 Mx=0.27 My=5.14 Fx=0.67 Fy=0.04
79/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.82 Mx=0.44 My=6.87 Fx=1.75 Fy=0.06
80/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.50 Mx=-6.97 My=-0.01 Fx=-0.00 Fy=1.96
81/ ULS : COMB9 (BETON) 1.4D N=47.96 Mx=-0.00 My=0.00 Fx=0.00 Fy=0.00
82/ ULS : COMB10 (BETON) 1.2D+1.6L N=46.15 Mx=-0.00 My=0.00 Fx=0.00 Fy=0.00
83/ ULS : COMB11 (BETON) 1.2D+1L N=44.26 Mx=-0.00 My=0.00 Fx=0.00 Fy=0.00
84/ ULS : COMB12 (BETON) 1.2D+0.5W N=41.25 Mx=-0.00 My=5.11 Fx=1.39 Fy=0.00
85/ ULS : COMB13 (BETON) 1.2D+1W N=41.40 Mx=-0.00 My=10.23 Fx=2.78 Fy=0.00
86/ ULS : COMB14 (BETON) 0.9D+1W N=31.12 Mx=0.00 My=10.23 Fx=2.78 Fy=-0.00
87/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.97 Mx=-0.00 My=7.17 Fx=1.82 Fy=0.00
88/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=44.26 Mx=-7.38 My=0.00 Fx=0.00 Fy=1.88
89/ ULS : COMB9 (BETON) 1.4D N=47.96 Mx=-0.00 My=-0.00 Fx=-0.00 Fy=0.00
90/ ULS : COMB10 (BETON) 1.2D+1.6L N=46.15 Mx=-0.00 My=-0.00 Fx=-0.00 Fy=0.00
91/ ULS : COMB11 (BETON) 1.2D+1L N=44.26 Mx=-0.00 My=-0.00 Fx=-0.00 Fy=0.00
92/ ULS : COMB12 (BETON) 1.2D+0.5W N=40.00 Mx=-0.00 My=2.57 Fx=0.34 Fy=0.00
93/ ULS : COMB13 (BETON) 1.2D+1W N=38.90 Mx=-0.00 My=5.14 Fx=0.67 Fy=0.00
94/ ULS : COMB14 (BETON) 0.9D+1W N=28.62 Mx=-0.00 My=5.14 Fx=0.67 Fy=0.00
95/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=44.55 Mx=-0.00 My=7.17 Fx=1.82 Fy=0.00
96/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=44.26 Mx=-7.38 My=-0.00 Fx=-0.00 Fy=1.88
97/ ULS : COMB9 (BETON) 1.4D N=47.23 Mx=-0.42 My=-0.00 Fx=-0.00 Fy=-0.07
98/ ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=-0.49 My=-0.00 Fx=-0.00 Fy=-0.06
99/ ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=-0.44 My=-0.00 Fx=-0.00 Fy=-0.06
100/ ULS : COMB12 (BETON) 1.2D+0.5W N=40.63 Mx=-0.36 My=5.12 Fx=1.39 Fy=-0.06
101/ ULS : COMB13 (BETON) 1.2D+1W N=40.77 Mx=-0.36 My=10.23 Fx=2.78 Fy=-0.06
102/ ULS : COMB14 (BETON) 0.9D+1W N=30.65 Mx=-0.27 My=10.23 Fx=2.78 Fy=-0.04
103/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.26 Mx=-0.44 My=7.21 Fx=1.83 Fy=-0.06
104/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.61 Mx=-7.84 My=-0.01 Fx=-0.00 Fy=1.84
105/ ULS : COMB9 (BETON) 1.4D N=47.23 Mx=-0.42 My=0.00 Fx=0.00 Fy=-0.07
106/ ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=-0.49 My=0.00 Fx=0.00 Fy=-0.06
107/ ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=-0.44 My=0.00 Fx=0.00 Fy=-0.06
108/ ULS : COMB12 (BETON) 1.2D+0.5W N=39.37 Mx=-0.36 My=2.57 Fx=0.34 Fy=-0.06
109/ ULS : COMB13 (BETON) 1.2D+1W N=38.27 Mx=-0.36 My=5.14 Fx=0.67 Fy=-0.06
110/ ULS : COMB14 (BETON) 0.9D+1W N=28.15 Mx=-0.27 My=5.14 Fx=0.67 Fy=-0.04
111/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.85 Mx=-0.44 My=7.21 Fx=1.83 Fy=-0.06
112/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.61 Mx=-7.84 My=0.01 Fx=0.00 Fy=1.84
113/ ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.05 My=-0.00 Fx=-0.00 Fy=0.01
114/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=-0.04 My=-0.00 Fx=-0.00 Fy=0.01
115/ ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=-0.04 My=-0.00 Fx=-0.00 Fy=0.01
116/ ULS : COMB12 (BETON) 1.2D+0.5W N=40.00 Mx=-0.04 My=5.11 Fx=1.39 Fy=0.01
117/ ULS : COMB13 (BETON) 1.2D+1W N=40.15 Mx=-0.04 My=10.23 Fx=2.78 Fy=0.01
118/ ULS : COMB14 (BETON) 0.9D+1W N=30.18 Mx=-0.03 My=10.23 Fx=2.78 Fy=0.01
119/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.56 Mx=-0.04 My=7.19 Fx=1.82 Fy=0.01
120/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.85 Mx=-7.46 My=0.00 Fx=0.00 Fy=1.92
121/ ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.05 My=0.00 Fx=0.00 Fy=0.01
122/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=-0.04 My=0.00 Fx=0.00 Fy=0.01
123/ ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=-0.04 My=0.00 Fx=0.00 Fy=0.01
124/ ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=-0.04 My=2.57 Fx=0.34 Fy=0.01
125/ ULS : COMB13 (BETON) 1.2D+1W N=37.64 Mx=-0.04 My=5.14 Fx=0.67 Fy=0.01
126/ ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=-0.03 My=5.14 Fx=0.67 Fy=0.01
127/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.15 Mx=-0.04 My=7.19 Fx=1.82 Fy=0.01
128/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.85 Mx=-7.46 My=-0.00 Fx=-0.00 Fy=1.92
129/ ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.06 My=0.00 Fx=0.00 Fy=0.02
130/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.66 Mx=-0.05 My=0.00 Fx=-0.00 Fy=0.02
131/ ULS : COMB11 (BETON) 1.2D+1L N=42.86 Mx=-0.05 My=0.00 Fx=-0.00 Fy=0.02
132/ ULS : COMB12 (BETON) 1.2D+0.5W N=40.01 Mx=-0.05 My=5.09 Fx=1.39 Fy=0.02
133/ ULS : COMB13 (BETON) 1.2D+1W N=40.15 Mx=-0.05 My=10.18 Fx=2.77 Fy=0.02
134/ ULS : COMB14 (BETON) 0.9D+1W N=30.19 Mx=-0.04 My=10.18 Fx=2.77 Fy=0.01
Date : 30/08/23 Page : 5
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
135/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.57 Mx=-0.05 My=7.18 Fx=1.82 Fy=0.02
136/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.48 My=0.00 Fx=0.00 Fy=1.92
137/ ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.06 My=-0.00 Fx=-0.00 Fy=0.02
138/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.66 Mx=-0.05 My=-0.00 Fx=0.00 Fy=0.02
139/ ULS : COMB11 (BETON) 1.2D+1L N=42.86 Mx=-0.05 My=-0.00 Fx=0.00 Fy=0.02
140/ ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=-0.05 My=2.54 Fx=0.33 Fy=0.02
141/ ULS : COMB13 (BETON) 1.2D+1W N=37.65 Mx=-0.05 My=5.08 Fx=0.65 Fy=0.01
142/ ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=-0.04 My=5.08 Fx=0.65 Fy=0.01
143/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.15 Mx=-0.05 My=7.18 Fx=1.82 Fy=0.01
144/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.48 My=-0.00 Fx=-0.00 Fy=1.92
145/ ULS : COMB9 (BETON) 1.4D N=46.55 Mx=-0.11 My=0.01 Fx=-0.00 Fy=0.04
146/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.70 Mx=-0.09 My=0.01 Fx=-0.00 Fy=0.03
147/ ULS : COMB11 (BETON) 1.2D+1L N=42.90 Mx=-0.09 My=0.01 Fx=-0.00 Fy=0.03
148/ ULS : COMB12 (BETON) 1.2D+0.5W N=40.06 Mx=-0.09 My=4.69 Fx=1.27 Fy=0.03
149/ ULS : COMB13 (BETON) 1.2D+1W N=40.21 Mx=-0.09 My=9.37 Fx=2.55 Fy=0.03
150/ ULS : COMB14 (BETON) 0.9D+1W N=30.24 Mx=-0.07 My=9.37 Fx=2.55 Fy=0.03
151/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.61 Mx=-0.09 My=7.13 Fx=1.81 Fy=0.03
152/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.91 Mx=-7.53 My=-0.16 Fx=-0.06 Fy=1.95
153/ ULS : COMB9 (BETON) 1.4D N=46.55 Mx=-0.11 My=-0.01 Fx=0.00 Fy=0.04
154/ ULS : COMB10 (BETON) 1.2D+1.6L N=44.70 Mx=-0.09 My=-0.01 Fx=0.00 Fy=0.03
155/ ULS : COMB11 (BETON) 1.2D+1L N=42.90 Mx=-0.09 My=-0.01 Fx=0.00 Fy=0.03
156/ ULS : COMB12 (BETON) 1.2D+0.5W N=38.79 Mx=-0.09 My=2.33 Fx=0.29 Fy=0.03
157/ ULS : COMB13 (BETON) 1.2D+1W N=37.68 Mx=-0.09 My=4.66 Fx=0.57 Fy=0.04
158/ ULS : COMB14 (BETON) 0.9D+1W N=27.70 Mx=-0.07 My=4.66 Fx=0.57 Fy=0.03
159/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.19 Mx=-0.09 My=7.12 Fx=1.81 Fy=0.03
160/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.91 Mx=-7.53 My=0.16 Fx=0.06 Fy=1.95
161/ ULS : COMB9 (BETON) 1.4D N=45.68 Mx=-3.97 My=3.94 Fx=-1.10 Fy=-0.73
162/ ULS : COMB10 (BETON) 1.2D+1.6L N=43.61 Mx=-4.60 My=4.52 Fx=-1.08 Fy=-0.62
163/ ULS : COMB11 (BETON) 1.2D+1L N=41.94 Mx=-4.15 My=4.09 Fx=-1.03 Fy=-0.62
164/ ULS : COMB12 (BETON) 1.2D+0.5W N=38.74 Mx=-3.40 My=6.21 Fx=0.04 Fy=-0.62
165/ ULS : COMB13 (BETON) 1.2D+1W N=38.33 Mx=-3.40 My=9.04 Fx=1.02 Fy=-0.62
166/ ULS : COMB14 (BETON) 0.9D+1W N=28.54 Mx=-2.55 My=8.20 Fx=1.26 Fy=-0.46
167/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=40.95 Mx=-4.15 My=11.73 Fx=1.23 Fy=-0.62
168/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=41.30 Mx=-11.42 My=4.11 Fx=-1.02 Fy=1.18
169/ ULS : COMB9 (BETON) 1.4D N=45.68 Mx=-3.97 My=-3.94 Fx=1.10 Fy=-0.73
170/ ULS : COMB10 (BETON) 1.2D+1.6L N=43.61 Mx=-4.60 My=-4.52 Fx=1.08 Fy=-0.62
171/ ULS : COMB11 (BETON) 1.2D+1L N=41.94 Mx=-4.15 My=-4.09 Fx=1.03 Fy=-0.62
172/ ULS : COMB12 (BETON) 1.2D+0.5W N=39.27 Mx=-3.40 My=-0.78 Fx=1.64 Fy=-0.62
173/ ULS : COMB13 (BETON) 1.2D+1W N=39.39 Mx=-3.40 My=1.81 Fx=2.34 Fy=-0.62
174/ ULS : COMB14 (BETON) 0.9D+1W N=29.60 Mx=-2.55 My=2.66 Fx=2.11 Fy=-0.47
175/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.92 Mx=-4.15 My=3.55 Fx=3.29 Fy=-0.62
176/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=41.30 Mx=-11.42 My=-4.11 Fx=1.02 Fy=1.18
177/* ULS : COMB9 (BETON) 1.4D N=47.71 Mx=3.97 My=4.74 Fx=-0.48 Fy=0.73
178/* ULS : COMB10 (BETON) 1.2D+1.6L N=45.82 Mx=4.60 My=5.38 Fx=-0.41 Fy=0.62
179/* ULS : COMB11 (BETON) 1.2D+1L N=43.97 Mx=4.15 My=4.89 Fx=-0.41 Fy=0.62
180/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.57 Mx=3.40 My=6.75 Fx=0.54 Fy=0.62
181/* ULS : COMB13 (BETON) 1.2D+1W N=40.24 Mx=3.41 My=9.43 Fx=1.50 Fy=0.62
182/* ULS : COMB14 (BETON) 0.9D+1W N=30.02 Mx=2.56 My=8.42 Fx=1.60 Fy=0.46
183/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.94 Mx=4.15 My=12.76 Fx=1.91 Fy=0.62
184/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=44.61 Mx=-3.04 My=4.86 Fx=-0.43 Fy=2.35
185/* ULS : COMB9 (BETON) 1.4D N=47.71 Mx=3.97 My=-4.74 Fx=0.48 Fy=0.73
186/* ULS : COMB10 (BETON) 1.2D+1.6L N=45.82 Mx=4.60 My=-5.38 Fx=0.41 Fy=0.62
187/* ULS : COMB11 (BETON) 1.2D+1L N=43.97 Mx=4.15 My=-4.89 Fx=0.41 Fy=0.62
188/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.99 Mx=3.40 My=-1.67 Fx=1.04 Fy=0.62
189/* ULS : COMB13 (BETON) 1.2D+1W N=41.08 Mx=3.40 My=0.72 Fx=1.68 Fy=0.62
190/* ULS : COMB14 (BETON) 0.9D+1W N=30.86 Mx=2.55 My=1.74 Fx=1.57 Fy=0.47
191/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=45.01 Mx=4.15 My=2.98 Fx=2.74 Fy=0.62
192/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=44.61 Mx=-3.04 My=-4.86 Fx=0.43 Fy=2.35
193/* ULS : COMB9 (BETON) 1.4D N=46.56 Mx=0.11 My=-0.01 Fx=-0.00 Fy=-0.04
194/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.71 Mx=0.09 My=-0.01 Fx=-0.00 Fy=-0.03
195/* ULS : COMB11 (BETON) 1.2D+1L N=42.91 Mx=0.09 My=-0.01 Fx=-0.00 Fy=-0.03
196/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.06 Mx=0.09 My=4.65 Fx=1.26 Fy=-0.03
197/* ULS : COMB13 (BETON) 1.2D+1W N=40.21 Mx=0.09 My=9.30 Fx=2.53 Fy=-0.03
198/* ULS : COMB14 (BETON) 0.9D+1W N=30.24 Mx=0.07 My=9.30 Fx=2.53 Fy=-0.03
199/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.65 Mx=0.09 My=6.84 Fx=1.74 Fy=-0.03
200/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.89 Mx=-7.38 My=0.22 Fx=0.08 Fy=1.89
201/* ULS : COMB9 (BETON) 1.4D N=46.56 Mx=0.11 My=0.01 Fx=0.00 Fy=-0.04
202/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.71 Mx=0.09 My=0.01 Fx=0.00 Fy=-0.03
203/* ULS : COMB11 (BETON) 1.2D+1L N=42.91 Mx=0.09 My=0.01 Fx=0.00 Fy=-0.03
204/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.79 Mx=0.09 My=2.31 Fx=0.28 Fy=-0.03
205/* ULS : COMB13 (BETON) 1.2D+1W N=37.68 Mx=0.09 My=4.60 Fx=0.56 Fy=-0.04
206/* ULS : COMB14 (BETON) 0.9D+1W N=27.70 Mx=0.07 My=4.60 Fx=0.56 Fy=-0.03
207/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.16 Mx=0.09 My=6.85 Fx=1.75 Fy=-0.04
208/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.89 Mx=-7.38 My=-0.22 Fx=-0.08 Fy=1.89
209/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=0.06 My=0.00 Fx=0.00 Fy=-0.02
210/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.66 Mx=0.05 My=0.00 Fx=0.00 Fy=-0.01
211/* ULS : COMB11 (BETON) 1.2D+1L N=42.86 Mx=0.05 My=0.00 Fx=0.00 Fy=-0.01
212/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.01 Mx=0.05 My=5.09 Fx=1.38 Fy=-0.01
Date : 30/08/23 Page : 6
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
213/* ULS : COMB13 (BETON) 1.2D+1W N=40.15 Mx=0.05 My=10.18 Fx=2.77 Fy=-0.02
214/* ULS : COMB14 (BETON) 0.9D+1W N=30.19 Mx=0.04 My=10.18 Fx=2.77 Fy=-0.01
215/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.60 Mx=0.05 My=6.79 Fx=1.73 Fy=-0.01
216/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.39 My=0.00 Fx=-0.00 Fy=1.90
217/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=0.06 My=-0.00 Fx=-0.00 Fy=-0.02
218/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.66 Mx=0.05 My=-0.00 Fx=-0.00 Fy=-0.01
219/* ULS : COMB11 (BETON) 1.2D+1L N=42.86 Mx=0.05 My=-0.00 Fx=-0.00 Fy=-0.01
220/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=0.05 My=2.53 Fx=0.33 Fy=-0.01
221/* ULS : COMB13 (BETON) 1.2D+1W N=37.64 Mx=0.05 My=5.07 Fx=0.65 Fy=-0.01
222/* ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=0.04 My=5.07 Fx=0.65 Fy=-0.01
223/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.12 Mx=0.05 My=6.79 Fx=1.73 Fy=-0.01
224/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.39 My=-0.00 Fx=0.00 Fy=1.90
225/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=0.04 My=0.00 Fx=0.00 Fy=-0.01
226/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=0.04 My=0.00 Fx=0.00 Fy=-0.01
227/* ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=0.04 My=0.00 Fx=0.00 Fy=-0.01
228/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.00 Mx=0.04 My=5.11 Fx=1.39 Fy=-0.01
229/* ULS : COMB13 (BETON) 1.2D+1W N=40.15 Mx=0.04 My=10.23 Fx=2.78 Fy=-0.01
230/* ULS : COMB14 (BETON) 0.9D+1W N=30.18 Mx=0.03 My=10.23 Fx=2.78 Fy=-0.01
231/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.60 Mx=0.04 My=6.79 Fx=1.73 Fy=-0.01
232/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.40 My=-0.00 Fx=-0.00 Fy=1.90
233/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=0.04 My=-0.00 Fx=-0.00 Fy=-0.01
234/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=0.04 My=-0.00 Fx=-0.00 Fy=-0.01
235/* ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=0.04 My=-0.00 Fx=-0.00 Fy=-0.01
236/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=0.04 My=2.57 Fx=0.33 Fy=-0.01
237/* ULS : COMB13 (BETON) 1.2D+1W N=37.64 Mx=0.04 My=5.14 Fx=0.67 Fy=-0.01
238/* ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=0.03 My=5.14 Fx=0.67 Fy=-0.01
239/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.11 Mx=0.04 My=6.79 Fx=1.73 Fy=-0.01
240/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.40 My=0.00 Fx=0.00 Fy=1.90
241/* ULS : COMB9 (BETON) 1.4D N=47.23 Mx=0.42 My=-0.00 Fx=-0.00 Fy=0.07
242/* ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=0.48 My=-0.00 Fx=-0.00 Fy=0.06
243/* ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=0.44 My=-0.00 Fx=-0.00 Fy=0.06
244/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.63 Mx=0.36 My=5.12 Fx=1.39 Fy=0.06
245/* ULS : COMB13 (BETON) 1.2D+1W N=40.77 Mx=0.36 My=10.23 Fx=2.78 Fy=0.06
246/* ULS : COMB14 (BETON) 0.9D+1W N=30.65 Mx=0.27 My=10.23 Fx=2.78 Fy=0.04
247/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.30 Mx=0.44 My=6.87 Fx=1.75 Fy=0.06
248/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.50 Mx=-6.97 My=0.01 Fx=0.00 Fy=1.96
249/* ULS : COMB9 (BETON) 1.4D N=47.23 Mx=0.42 My=0.00 Fx=0.00 Fy=0.07
250/* ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=0.48 My=0.00 Fx=0.00 Fy=0.06
251/* ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=0.44 My=0.00 Fx=0.00 Fy=0.06
252/* ULS : COMB12 (BETON) 1.2D+0.5W N=39.37 Mx=0.36 My=2.57 Fx=0.34 Fy=0.06
253/* ULS : COMB13 (BETON) 1.2D+1W N=38.27 Mx=0.36 My=5.14 Fx=0.67 Fy=0.06
254/* ULS : COMB14 (BETON) 0.9D+1W N=28.15 Mx=0.27 My=5.14 Fx=0.67 Fy=0.04
255/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.82 Mx=0.44 My=6.87 Fx=1.75 Fy=0.06
256/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.50 Mx=-6.97 My=-0.01 Fx=-0.00 Fy=1.96
257/* ULS : COMB9 (BETON) 1.4D N=47.96 Mx=-0.00 My=0.00 Fx=0.00 Fy=0.00
258/* ULS : COMB10 (BETON) 1.2D+1.6L N=46.15 Mx=-0.00 My=0.00 Fx=0.00 Fy=0.00
259/* ULS : COMB11 (BETON) 1.2D+1L N=44.26 Mx=-0.00 My=0.00 Fx=0.00 Fy=0.00
260/* ULS : COMB12 (BETON) 1.2D+0.5W N=41.25 Mx=-0.00 My=5.11 Fx=1.39 Fy=0.00
261/* ULS : COMB13 (BETON) 1.2D+1W N=41.40 Mx=-0.00 My=10.23 Fx=2.78 Fy=0.00
262/* ULS : COMB14 (BETON) 0.9D+1W N=31.12 Mx=0.00 My=10.23 Fx=2.78 Fy=-0.00
263/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.97 Mx=-0.00 My=7.17 Fx=1.82 Fy=0.00
264/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=44.26 Mx=-7.38 My=0.00 Fx=0.00 Fy=1.88
265/* ULS : COMB9 (BETON) 1.4D N=47.96 Mx=-0.00 My=-0.00 Fx=-0.00 Fy=0.00
266/* ULS : COMB10 (BETON) 1.2D+1.6L N=46.15 Mx=-0.00 My=-0.00 Fx=-0.00 Fy=0.00
267/* ULS : COMB11 (BETON) 1.2D+1L N=44.26 Mx=-0.00 My=-0.00 Fx=-0.00 Fy=0.00
268/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.00 Mx=-0.00 My=2.57 Fx=0.34 Fy=0.00
269/* ULS : COMB13 (BETON) 1.2D+1W N=38.90 Mx=-0.00 My=5.14 Fx=0.67 Fy=0.00
270/* ULS : COMB14 (BETON) 0.9D+1W N=28.62 Mx=-0.00 My=5.14 Fx=0.67 Fy=0.00
271/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=44.55 Mx=-0.00 My=7.17 Fx=1.82 Fy=0.00
272/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=44.26 Mx=-7.38 My=-0.00 Fx=-0.00 Fy=1.88
273/* ULS : COMB9 (BETON) 1.4D N=47.23 Mx=-0.42 My=-0.00 Fx=-0.00 Fy=-0.07
274/* ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=-0.49 My=-0.00 Fx=-0.00 Fy=-0.06
275/* ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=-0.44 My=-0.00 Fx=-0.00 Fy=-0.06
276/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.63 Mx=-0.36 My=5.12 Fx=1.39 Fy=-0.06
277/* ULS : COMB13 (BETON) 1.2D+1W N=40.77 Mx=-0.36 My=10.23 Fx=2.78 Fy=-0.06
278/* ULS : COMB14 (BETON) 0.9D+1W N=30.65 Mx=-0.27 My=10.23 Fx=2.78 Fy=-0.04
279/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.26 Mx=-0.44 My=7.21 Fx=1.83 Fy=-0.06
280/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.61 Mx=-7.84 My=-0.01 Fx=-0.00 Fy=1.84
281/* ULS : COMB9 (BETON) 1.4D N=47.23 Mx=-0.42 My=0.00 Fx=0.00 Fy=-0.07
282/* ULS : COMB10 (BETON) 1.2D+1.6L N=45.40 Mx=-0.49 My=0.00 Fx=0.00 Fy=-0.06
283/* ULS : COMB11 (BETON) 1.2D+1L N=43.56 Mx=-0.44 My=0.00 Fx=0.00 Fy=-0.06
284/* ULS : COMB12 (BETON) 1.2D+0.5W N=39.37 Mx=-0.36 My=2.57 Fx=0.34 Fy=-0.06
285/* ULS : COMB13 (BETON) 1.2D+1W N=38.27 Mx=-0.36 My=5.14 Fx=0.67 Fy=-0.06
286/* ULS : COMB14 (BETON) 0.9D+1W N=28.15 Mx=-0.27 My=5.14 Fx=0.67 Fy=-0.04
287/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.85 Mx=-0.44 My=7.21 Fx=1.83 Fy=-0.06
288/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=43.61 Mx=-7.84 My=0.01 Fx=0.00 Fy=1.84
289/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.05 My=-0.00 Fx=-0.00 Fy=0.01
290/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=-0.04 My=-0.00 Fx=-0.00 Fy=0.01
Date : 30/08/23 Page : 7
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
291/* ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=-0.04 My=-0.00 Fx=-0.00 Fy=0.01
292/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.00 Mx=-0.04 My=5.11 Fx=1.39 Fy=0.01
293/* ULS : COMB13 (BETON) 1.2D+1W N=40.15 Mx=-0.04 My=10.23 Fx=2.78 Fy=0.01
294/* ULS : COMB14 (BETON) 0.9D+1W N=30.18 Mx=-0.03 My=10.23 Fx=2.78 Fy=0.01
295/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.56 Mx=-0.04 My=7.19 Fx=1.82 Fy=0.01
296/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.85 Mx=-7.46 My=0.00 Fx=0.00 Fy=1.92
297/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.05 My=0.00 Fx=0.00 Fy=0.01
298/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.65 Mx=-0.04 My=0.00 Fx=0.00 Fy=0.01
299/* ULS : COMB11 (BETON) 1.2D+1L N=42.85 Mx=-0.04 My=0.00 Fx=0.00 Fy=0.01
300/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=-0.04 My=2.57 Fx=0.34 Fy=0.01
301/* ULS : COMB13 (BETON) 1.2D+1W N=37.64 Mx=-0.04 My=5.14 Fx=0.67 Fy=0.01
302/* ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=-0.03 My=5.14 Fx=0.67 Fy=0.01
303/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.15 Mx=-0.04 My=7.19 Fx=1.82 Fy=0.01
304/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.85 Mx=-7.46 My=-0.00 Fx=-0.00 Fy=1.92
305/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.06 My=0.00 Fx=0.00 Fy=0.02
306/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.66 Mx=-0.05 My=0.00 Fx=-0.00 Fy=0.02
307/* ULS : COMB11 (BETON) 1.2D+1L N=42.86 Mx=-0.05 My=0.00 Fx=-0.00 Fy=0.02
308/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.01 Mx=-0.05 My=5.09 Fx=1.39 Fy=0.02
309/* ULS : COMB13 (BETON) 1.2D+1W N=40.15 Mx=-0.05 My=10.18 Fx=2.77 Fy=0.02
310/* ULS : COMB14 (BETON) 0.9D+1W N=30.19 Mx=-0.04 My=10.18 Fx=2.77 Fy=0.01
311/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.57 Mx=-0.05 My=7.18 Fx=1.82 Fy=0.02
312/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.48 My=0.00 Fx=0.00 Fy=1.92
313/* ULS : COMB9 (BETON) 1.4D N=46.50 Mx=-0.06 My=-0.00 Fx=-0.00 Fy=0.02
314/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.66 Mx=-0.05 My=-0.00 Fx=0.00 Fy=0.02
315/* ULS : COMB11 (BETON) 1.2D+1L N=42.86 Mx=-0.05 My=-0.00 Fx=0.00 Fy=0.02
316/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.75 Mx=-0.05 My=2.54 Fx=0.33 Fy=0.02
317/* ULS : COMB13 (BETON) 1.2D+1W N=37.65 Mx=-0.05 My=5.08 Fx=0.65 Fy=0.01
318/* ULS : COMB14 (BETON) 0.9D+1W N=27.68 Mx=-0.04 My=5.08 Fx=0.65 Fy=0.01
319/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.15 Mx=-0.05 My=7.18 Fx=1.82 Fy=0.01
320/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.86 Mx=-7.48 My=-0.00 Fx=-0.00 Fy=1.92
321/* ULS : COMB9 (BETON) 1.4D N=46.55 Mx=-0.11 My=0.01 Fx=-0.00 Fy=0.04
322/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.70 Mx=-0.09 My=0.01 Fx=-0.00 Fy=0.03
323/* ULS : COMB11 (BETON) 1.2D+1L N=42.90 Mx=-0.09 My=0.01 Fx=-0.00 Fy=0.03
324/* ULS : COMB12 (BETON) 1.2D+0.5W N=40.06 Mx=-0.09 My=4.69 Fx=1.27 Fy=0.03
325/* ULS : COMB13 (BETON) 1.2D+1W N=40.21 Mx=-0.09 My=9.37 Fx=2.55 Fy=0.03
326/* ULS : COMB14 (BETON) 0.9D+1W N=30.24 Mx=-0.07 My=9.37 Fx=2.55 Fy=0.03
327/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.61 Mx=-0.09 My=7.13 Fx=1.81 Fy=0.03
328/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.91 Mx=-7.53 My=-0.16 Fx=-0.06 Fy=1.95
329/* ULS : COMB9 (BETON) 1.4D N=46.55 Mx=-0.11 My=-0.01 Fx=0.00 Fy=0.04
330/* ULS : COMB10 (BETON) 1.2D+1.6L N=44.70 Mx=-0.09 My=-0.01 Fx=0.00 Fy=0.03
331/* ULS : COMB11 (BETON) 1.2D+1L N=42.90 Mx=-0.09 My=-0.01 Fx=0.00 Fy=0.03
332/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.79 Mx=-0.09 My=2.33 Fx=0.29 Fy=0.03
333/* ULS : COMB13 (BETON) 1.2D+1W N=37.68 Mx=-0.09 My=4.66 Fx=0.57 Fy=0.04
334/* ULS : COMB14 (BETON) 0.9D+1W N=27.70 Mx=-0.07 My=4.66 Fx=0.57 Fy=0.03
335/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=43.19 Mx=-0.09 My=7.12 Fx=1.81 Fy=0.03
336/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=42.91 Mx=-7.53 My=0.16 Fx=0.06 Fy=1.95
337/* ULS : COMB9 (BETON) 1.4D N=45.68 Mx=-3.97 My=3.94 Fx=-1.10 Fy=-0.73
338/* ULS : COMB10 (BETON) 1.2D+1.6L N=43.61 Mx=-4.60 My=4.52 Fx=-1.08 Fy=-0.62
339/* ULS : COMB11 (BETON) 1.2D+1L N=41.94 Mx=-4.15 My=4.09 Fx=-1.03 Fy=-0.62
340/* ULS : COMB12 (BETON) 1.2D+0.5W N=38.74 Mx=-3.40 My=6.21 Fx=0.04 Fy=-0.62
341/* ULS : COMB13 (BETON) 1.2D+1W N=38.33 Mx=-3.40 My=9.04 Fx=1.02 Fy=-0.62
342/* ULS : COMB14 (BETON) 0.9D+1W N=28.54 Mx=-2.55 My=8.20 Fx=1.26 Fy=-0.46
343/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=40.95 Mx=-4.15 My=11.73 Fx=1.23 Fy=-0.62
344/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=41.30 Mx=-11.42 My=4.11 Fx=-1.02 Fy=1.18
345/* ULS : COMB9 (BETON) 1.4D N=45.68 Mx=-3.97 My=-3.94 Fx=1.10 Fy=-0.73
346/* ULS : COMB10 (BETON) 1.2D+1.6L N=43.61 Mx=-4.60 My=-4.52 Fx=1.08 Fy=-0.62
347/* ULS : COMB11 (BETON) 1.2D+1L N=41.94 Mx=-4.15 My=-4.09 Fx=1.03 Fy=-0.62
348/* ULS : COMB12 (BETON) 1.2D+0.5W N=39.27 Mx=-3.40 My=-0.78 Fx=1.64 Fy=-0.62
349/* ULS : COMB13 (BETON) 1.2D+1W N=39.39 Mx=-3.40 My=1.81 Fx=2.34 Fy=-0.62
350/* ULS : COMB14 (BETON) 0.9D+1W N=29.60 Mx=-2.55 My=2.66 Fx=2.11 Fy=-0.47
351/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=42.92 Mx=-4.15 My=3.55 Fx=3.29 Fy=-0.62
352/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=41.30 Mx=-11.42 My=-4.11 Fx=1.02 Fy=1.18
1.2.1 Assumptions
1.2.2 Soil:
Date : 30/08/23 Page : 8
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
sandy clays
• Soil level: 0.00 (m)
• Unit weight:2082.40 (kG/m3)
• Unit weight of solid: 2732.75 (kG/m3)
• Internal friction angle: 20.0 (Deg)
• Cohesion: 86.18 (kPa)
1.3 RC design
1.3.1 Assumptions
Shear
Spread footing:
bottom:
top:
Column pier:
Longitudinal reinforcement A = 1225.00 (mm2) A min. = 1225.00 (mm2)
A = 2 * (Asx + Asy)
Asx = 252.57 (mm2)Asy = 359.93 (mm2)
2.3.2 Pier
Longitudinal reinforcement
Dowels
Longitudinal reinforcement
8 Grade 420 16 l = 1.38 (m) e = 1*-0.14 + 1*0.01 + 2*0.13 + 1*0.01
2 Material survey:
⦁ Concrete volume = 0.70 (m3)
⦁ Formwork = 2.08 (m2)
3 1 -20
20
Ø16 Grade 420 Ø10 Grade 300
l=1.38 5 6 l=1.38
3x10
30
4
13x10 -55
58
75
5
Ø10 Grade 420 Ø10 Grade 420
Ø10 Grade 420 Ø10 Grade 420
1 l=1.68 4 l=1.68 3 l=1.68 2 l=1.68
e=10 e=10 e=10 e=10
1.50
13x10
13x10
1.50
35
X 0 Y-Y
75
58
13x10 -20
20
Ø16 Grade 420 Ø10 Grade 300
2 l=1.38 5 6 l=1.38
3x10
30
75 75 -55
58 35 58
5
1.50 Ø10 Grade 420 Ø10 Grade 420 Ø10 Grade
Ø10 Grade
420 420
2 l=1.68 3 l=1.68 4 1 l=1.68
l=1.68
e=10 e=10 e=10 e=10
1.50
Pos. Reinforcement Code Shape Steel Number Pos. Reinforcement Code Shape Steel Number
1 Ø10 Grade 420 l=1.68 T17 Grade 420 14 4 Ø10 Grade 420 l=1.68 T17 Grade 420 14
11
11
11
11
1.46 1.46
41
16
2 Ø10 Grade 420 l=1.68 T17 Grade 420 14 5 Ø16 Grade 420 l=1.38 Grade 420 8
11
11
1.46
85
31
3 Ø10 Grade 420 l=1.68 T17 Grade 420 14 6 Ø10 Grade 300 l=1.38 T1 Grade 300 4
11
11
1.46
31
11
1.1.1 Assumptions
1.1.2 Geometry:
1.1.3 Materials
1.1.4 Loads:
Foundation loads:
Case Nature Group N Fx Fy Mx My
(kN) (kN) (kN) (kN*m) (kN*m)
COMB9 (BETON) 1.4D design ---- 37.40 -0.02 0.00 0.00 0.33
COMB10 (BETON) 1.2D+1.6L design ---- 37.18 -0.01 0.00 0.00 0.37
COMB11 (BETON) 1.2D+1L design ---- 35.26 -0.01 0.00 0.00 0.34
COMB12 (BETON) 1.2D+0.5W design ---- 33.01 0.10 0.01 -0.01 0.56
COMB13 (BETON) 1.2D+1W design ---- 33.96 0.21 0.01 -0.02 0.84
COMB14 (BETON) 0.9D+1W design ---- 25.95 0.21 0.01 -0.02 0.77
Date : 30/08/23 Page : 1
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
COMB15 (BETON) 1.2D+1Ex+1L design ---- 35.98 0.34 0.00 0.00 1.21
COMB16 (BETON) 1.2D+1Ey+1L design ---- 35.27 -0.01 0.23 -1.45 0.33
COMB9 (BETON) 1.4D design ---- 38.50 0.00 -0.00 0.01 0.00
COMB10 (BETON) 1.2D+1.6L design ---- 38.20 0.00 -0.00 0.01 0.00
COMB11 (BETON) 1.2D+1L design ---- 36.25 0.00 -0.00 0.01 0.00
COMB12 (BETON) 1.2D+0.5W design ---- 32.84 0.12 0.00 0.00 0.29
COMB13 (BETON) 1.2D+1W design ---- 32.68 0.23 0.00 -0.00 0.57
COMB14 (BETON) 0.9D+1W design ---- 24.43 0.23 0.00 -0.00 0.57
COMB15 (BETON) 1.2D+1Ex+1L design ---- 36.25 0.37 -0.00 0.01 0.90
COMB16 (BETON) 1.2D+1Ey+1L design ---- 36.28 -0.00 0.57 -2.51 -0.00
COMB9 (BETON) 1.4D design ---- 37.40 0.02 0.00 0.00 -0.33
COMB10 (BETON) 1.2D+1.6L design ---- 37.18 0.01 0.00 0.00 -0.37
COMB11 (BETON) 1.2D+1L design ---- 35.26 0.01 0.00 0.00 -0.34
COMB12 (BETON) 1.2D+0.5W design ---- 30.54 0.12 0.00 0.00 -0.01
COMB13 (BETON) 1.2D+1W design ---- 29.03 0.23 0.00 0.00 0.27
COMB14 (BETON) 0.9D+1W design ---- 21.01 0.23 -0.00 0.00 0.34
COMB15 (BETON) 1.2D+1Ex+1L design ---- 34.54 0.37 0.00 -0.00 0.54
COMB16 (BETON) 1.2D+1Ey+1L design ---- 35.27 0.01 0.23 -1.45 -0.33
COMB9 (BETON) 1.4D design ---- 60.92 -2.36 -0.00 -0.00 7.40
COMB10 (BETON) 1.2D+1.6L design ---- 65.61 -2.63 -0.00 -0.00 9.78
COMB11 (BETON) 1.2D+1L design ---- 60.59 -2.40 -0.00 -0.00 8.49
COMB12 (BETON) 1.2D+0.5W design ---- 53.25 -1.91 -0.01 0.01 6.63
COMB13 (BETON) 1.2D+1W design ---- 54.29 -1.81 -0.01 0.02 6.91
COMB14 (BETON) 0.9D+1W design ---- 41.24 -1.30 -0.01 0.02 5.33
COMB15 (BETON) 1.2D+1Ex+1L design ---- 61.48 -2.07 -0.00 -0.00 9.32
COMB16 (BETON) 1.2D+1Ey+1L design ---- 60.57 -2.40 0.30 -1.38 8.49
COMB9 (BETON) 1.4D design ---- 60.92 2.36 -0.00 -0.00 -7.40
COMB10 (BETON) 1.2D+1.6L design ---- 65.61 2.63 -0.00 -0.00 -9.78
COMB11 (BETON) 1.2D+1L design ---- 60.59 2.40 -0.00 -0.00 -8.49
COMB12 (BETON) 1.2D+0.5W design ---- 50.52 2.14 -0.00 -0.00 -6.05
COMB13 (BETON) 1.2D+1W design ---- 48.83 2.25 -0.00 -0.00 -5.76
COMB14 (BETON) 0.9D+1W design ---- 35.77 1.74 -0.00 -0.00 -4.18
COMB15 (BETON) 1.2D+1Ex+1L design ---- 59.70 2.73 -0.00 -0.00 -7.66
COMB16 (BETON) 1.2D+1Ey+1L design ---- 60.57 2.40 0.30 -1.38 -8.49
Backfill loads:
Case Nature Q1
(kN/m2)
37/ ULS : COMB13 (BETON) 1.2D+1W N=48.83 Mx=-0.00 My=-5.76 Fx=2.25 Fy=-0.00
38/ ULS : COMB14 (BETON) 0.9D+1W N=35.77 Mx=-0.00 My=-4.18 Fx=1.74 Fy=-0.00
39/ ULS : COMB15 (BETON) 1.2D+1Ex+1L N=59.70 Mx=-0.00 My=-7.66 Fx=2.73 Fy=-0.00
40/ ULS : COMB16 (BETON) 1.2D+1Ey+1L N=60.57 Mx=-1.38 My=-8.49 Fx=2.40 Fy=0.30
41/* ULS : COMB9 (BETON) 1.4D N=37.40 Mx=0.00 My=0.33 Fx=-0.02 Fy=0.00
42/* ULS : COMB10 (BETON) 1.2D+1.6L N=37.18 Mx=0.00 My=0.37 Fx=-0.01 Fy=0.00
43/* ULS : COMB11 (BETON) 1.2D+1L N=35.26 Mx=0.00 My=0.34 Fx=-0.01 Fy=0.00
44/* ULS : COMB12 (BETON) 1.2D+0.5W N=33.01 Mx=-0.01 My=0.56 Fx=0.10 Fy=0.01
45/* ULS : COMB13 (BETON) 1.2D+1W N=33.96 Mx=-0.02 My=0.84 Fx=0.21 Fy=0.01
46/* ULS : COMB14 (BETON) 0.9D+1W N=25.95 Mx=-0.02 My=0.77 Fx=0.21 Fy=0.01
47/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=35.98 Mx=0.00 My=1.21 Fx=0.34 Fy=0.00
48/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=35.27 Mx=-1.45 My=0.33 Fx=-0.01 Fy=0.23
49/* ULS : COMB9 (BETON) 1.4D N=38.50 Mx=0.01 Fy=-0.00
50/* ULS : COMB10 (BETON) 1.2D+1.6L N=38.20 Mx=0.01 Fy=-0.00
51/* ULS : COMB11 (BETON) 1.2D+1L N=36.25 Mx=0.01 Fy=-0.00
52/* ULS : COMB12 (BETON) 1.2D+0.5W N=32.84 Mx=0.00 My=0.29 Fx=0.12 Fy=0.00
53/* ULS : COMB13 (BETON) 1.2D+1W N=32.68 Mx=-0.00 My=0.57 Fx=0.23 Fy=0.00
54/* ULS : COMB14 (BETON) 0.9D+1W N=24.43 Mx=-0.00 My=0.57 Fx=0.23 Fy=0.00
55/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=36.25 Mx=0.01 My=0.90 Fx=0.37 Fy=-0.00
56/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=36.28 Mx=-2.51 Fy=0.57
57/* ULS : COMB9 (BETON) 1.4D N=37.40 Mx=0.00 My=-0.33 Fx=0.02 Fy=0.00
58/* ULS : COMB10 (BETON) 1.2D+1.6L N=37.18 Mx=0.00 My=-0.37 Fx=0.01 Fy=0.00
59/* ULS : COMB11 (BETON) 1.2D+1L N=35.26 Mx=0.00 My=-0.34 Fx=0.01 Fy=0.00
60/* ULS : COMB12 (BETON) 1.2D+0.5W N=30.54 Mx=0.00 My=-0.01 Fx=0.12 Fy=0.00
61/* ULS : COMB13 (BETON) 1.2D+1W N=29.03 Mx=0.00 My=0.27 Fx=0.23 Fy=0.00
62/* ULS : COMB14 (BETON) 0.9D+1W N=21.01 Mx=0.00 My=0.34 Fx=0.23 Fy=-0.00
63/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=34.54 Mx=-0.00 My=0.54 Fx=0.37 Fy=0.00
64/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=35.27 Mx=-1.45 My=-0.33 Fx=0.01 Fy=0.23
65/* ULS : COMB9 (BETON) 1.4D N=60.92 Mx=-0.00 My=7.40 Fx=-2.36 Fy=-0.00
66/* ULS : COMB10 (BETON) 1.2D+1.6L N=65.61 Mx=-0.00 My=9.78 Fx=-2.63 Fy=-0.00
67/* ULS : COMB11 (BETON) 1.2D+1L N=60.59 Mx=-0.00 My=8.49 Fx=-2.40 Fy=-0.00
68/* ULS : COMB12 (BETON) 1.2D+0.5W N=53.25 Mx=0.01 My=6.63 Fx=-1.91 Fy=-0.01
69/* ULS : COMB13 (BETON) 1.2D+1W N=54.29 Mx=0.02 My=6.91 Fx=-1.81 Fy=-0.01
70/* ULS : COMB14 (BETON) 0.9D+1W N=41.24 Mx=0.02 My=5.33 Fx=-1.30 Fy=-0.01
71/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=61.48 Mx=-0.00 My=9.32 Fx=-2.07 Fy=-0.00
72/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=60.57 Mx=-1.38 My=8.49 Fx=-2.40 Fy=0.30
73/* ULS : COMB9 (BETON) 1.4D N=60.92 Mx=-0.00 My=-7.40 Fx=2.36 Fy=-0.00
74/* ULS : COMB10 (BETON) 1.2D+1.6L N=65.61 Mx=-0.00 My=-9.78 Fx=2.63 Fy=-0.00
75/* ULS : COMB11 (BETON) 1.2D+1L N=60.59 Mx=-0.00 My=-8.49 Fx=2.40 Fy=-0.00
76/* ULS : COMB12 (BETON) 1.2D+0.5W N=50.52 Mx=-0.00 My=-6.05 Fx=2.14 Fy=-0.00
77/* ULS : COMB13 (BETON) 1.2D+1W N=48.83 Mx=-0.00 My=-5.76 Fx=2.25 Fy=-0.00
78/* ULS : COMB14 (BETON) 0.9D+1W N=35.77 Mx=-0.00 My=-4.18 Fx=1.74 Fy=-0.00
79/* ULS : COMB15 (BETON) 1.2D+1Ex+1L N=59.70 Mx=-0.00 My=-7.66 Fx=2.73 Fy=-0.00
80/* ULS : COMB16 (BETON) 1.2D+1Ey+1L N=60.57 Mx=-1.38 My=-8.49 Fx=2.40 Fy=0.30
1.2.1 Assumptions
1.2.2 Soil:
sandy clays
• Soil level: 0.00 (m)
• Unit weight:2082.40 (kG/m3)
• Unit weight of solid: 2732.75 (kG/m3)
• Internal friction angle: 20.0 (Deg)
• Cohesion: 86.18 (kPa)
1.3 RC design
1.3.1 Assumptions
Shear
Spread footing:
bottom:
top:
A'sx = 0.00 (mm2/m)
A'sy = 0.00 (mm2/m)
Column pier:
Longitudinal reinforcement A = 300.00 (mm2)A min. = 300.00 (mm2)
A = 2 * (Asx + Asy)
Asx = 76.52 (mm2) Asy = 73.48 (mm2)
Along X axis:
9 Grade 420 10 l = 1.12 (m) e = 1*-0.40 + 8*0.10
Along Y axis:
9 Grade 420 10 l = 1.12 (m) e = 1*-0.40 + 8*0.10
Top:
Along X axis:
9 Grade 420 10 l = 1.12 (m) e = 1*-0.40 + 8*0.10
Along Y axis:
9 Grade 420 10 l = 1.12 (m) e = 1*-0.40 + 8*0.10
2.3.2 Pier
Longitudinal reinforcement
Dowels
Longitudinal reinforcement
8 Grade 420 13 l = 1.13 (m) e = 1*-0.04 + 1*0.01 + 1*0.06 + 1*0.01
2 Material survey:
⦁ Concrete volume = 0.31 (m3)
⦁ Formwork = 1.34 (m2)
20
Ø13 Grade 420 Ø10 Grade 300
3 1 l=1.14 5 6 l=68
2x10
30
-55
8x10
4
43
50
5
Ø10 Grade
Ø10 Grade
420 420 Ø10 Grade
Ø10 Grade
420 420
4 1 l=1.12
l=1.12 3 2 l=1.12
l=1.12
e=10 e=10 e=10 e=10
1.00
8x10
8x10
1.00
15
X 0 Y-Y
50
43
8x10
2 -20
20
Ø13 Grade 420 Ø10 Grade 300
l=1.14 5 6 l=68
2x10
50 50
30
-55
40 20 40
1.00
5
Ø10 Grade 420 Ø10 Grade 420
Ø10 Grade
Ø10 Grade
420 420
3 l=1.12 2 l=1.12 4 l=1.12
1 l=1.12
e=10 e=10 e=10 e=10
1.00
Pos. Reinforcement Code Shape Steel Number Pos. Reinforcement Code Shape Steel Number
1 Ø10 Grade 420 l=1.12 T17 Grade 420 9 4 Ø10 Grade 420 l=1.12 T17 Grade 420 9
11
11
11
11
90 90
40
14
2 Ø10 Grade 420 l=1.12 T17 Grade 420 9 5 Ø13 Grade 420 l=1.14 Grade 420 8
11
11
90
63
16
3 Ø10 Grade 420 l=1.12 T17 Grade 420 9 6 Ø10 Grade 300 l=68 T1 Grade 300 3
11
11
90
11
11
1 Level:
⦁ Name : Level +0.00
⦁ Reference level : 4.33 (m)
⦁ Fire rating : 0 (h)
2.2 Geometry:
2.2.1 Span Position L.supp. L R.supp.
(m) (m) (m)
P1 Span 0.35 2.65 0.35
Span length: Lo = 3.00 (m)
Section from 0.00 to 2.65 (m)
200.00 x 300.00 (mm)
without left slab
without right slab
-30
-20
-10
10
20
30
40
[m]
50
0 5 10 15 20 25 30
Bending Moment ULS: Mu Mu,rd fi*Mn
20
[kN]
15
10
-5
-10
-15
[m]
-20
0 5 10 15 20 25 30
Shear Force ULS: Vu Vu,rd fi*(Vc+Vs) fi*Vn
400
200
200
400
[m]
600
0 5 10 15 20 25 30
Reinforcement Area for Bending: As/As' Ast,red As,min As,des Ast
1500
[mm2/m]
1000
500
500
1000
[m]
1500
0 5 10 15 20 25 30
Reinforcement Area for Shear: Av Av,min Av,hang
2.4.5 Deflections
d(L) - initial live-load deflection
d(D) - initial dead-load deflection
d(LS) - initial sustained live-load deflection
d(LT) - total sustained live-load deflection
d(LT),lim - allowable deflection
-0.015
[m]
-0.01
-0.005
0.005
0.01
[m]
0.015
0 5 10 15 20 25 30
Deflections: d_s(D+LS) d_l(D+LS) d_s(D+L) d(LT) d(LT),lim
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
0.35 9.62 0.00
0.48 8.71 0.00
0.78 6.53 0.00
1.08 4.36 0.00
1.38 2.18 0.00
1.68 0.00 0.00
1.98 -2.18 0.00
2.28 -4.36 0.00
2.58 -6.53 0.00
2.88 -8.71 0.00
3.00 -9.62 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
3.35 9.62 0.00
3.48 8.71 0.00
3.78 6.53 0.00
4.08 4.36 0.00
4.38 2.18 0.00
4.68 0.00 0.00
4.98 -2.18 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
6.35 9.62 0.00
6.48 8.71 0.00
6.78 6.53 0.00
7.08 4.36 0.00
7.38 2.18 0.00
7.68 0.00 0.00
7.98 -2.18 0.00
8.28 -4.36 0.00
8.58 -6.53 0.00
8.88 -8.71 0.00
9.00 -9.62 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
9.35 9.62 0.00
9.48 8.71 0.00
9.78 6.53 0.00
10.08 4.36 0.00
10.38 2.18 0.00
10.68 0.00 0.00
10.98 -2.18 0.00
11.28 -4.36 0.00
11.58 -6.53 0.00
11.88 -8.71 0.00
12.00 -9.62 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
12.35 10.16 0.00
12.49 9.15 0.00
12.81 6.86 0.00
13.12 4.57 0.00
13.44 2.29 0.00
13.75 0.00 0.00
14.07 -2.29 0.00
14.38 -4.57 0.00
14.70 -6.86 0.00
15.01 -9.15 0.00
15.15 -10.16 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
15.50 10.16 0.00
15.64 9.15 0.00
15.96 6.86 0.00
16.27 4.57 0.00
16.59 2.29 0.00
16.90 0.00 0.00
17.22 -2.29 0.00
17.53 -4.57 0.00
17.85 -6.86 0.00
18.16 -9.15 0.00
18.30 -10.16 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
Date : 30/08/23 Page : 7
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
21.65 9.62 0.00
21.78 8.71 0.00
22.08 6.53 0.00
22.38 4.36 0.00
22.68 2.18 0.00
22.98 0.00 0.00
23.28 -2.18 0.00
23.58 -4.36 0.00
23.88 -6.53 0.00
24.18 -8.71 0.00
24.30 -9.62 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
24.65 9.62 0.00
24.78 8.71 0.00
25.08 6.53 0.00
25.38 4.36 0.00
25.68 2.18 0.00
25.98 0.00 0.00
26.28 -2.18 0.00
26.58 -4.36 0.00
26.88 -6.53 0.00
27.18 -8.71 0.00
27.30 -9.62 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
27.65 9.62 0.00
27.78 8.71 0.00
28.08 6.53 0.00
28.38 4.36 0.00
28.68 2.18 0.00
28.98 0.00 0.00
29.28 -2.18 0.00
29.58 -4.36 0.00
29.88 -6.53 0.00
30.18 -8.71 0.00
30.30 -9.62 0.00
2.6 Reinforcement:
2.6.1 P1 : Span from 0.35 to 3.00 (m)
Longitudinal reinforcement:
⦁ bottom (Grade 420)
2 13 l = 1.33 from 2.34 to 1.01
⦁ support (Grade 420)
2 13 l = 1.21 from 0.03 to 0.03
Transversal reinforcement:
⦁ main (Grade 300)
stirrups 20 10 l = 0.98
e = 1*0.00 + 19*0.14 (m)
Longitudinal reinforcement:
⦁ bottom (Grade 420)
2 13 l = 1.33 from 29.64 to 28.31
⦁ support (Grade 420)
2 13 l = 1.68 from 26.64 to 28.31
2 13 l = 1.22 from 29.63 to 30.62
Transversal reinforcement:
⦁ main (Grade 300)
stirrups 20 10 l = 0.98
e = 1*-0.00 + 19*0.14 (m)
3 Material survey:
⦁ Concrete volume = 1.84 (m3)
⦁ Formwork = 23.87 (m2)
-33
0.0
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
A 420
Ø13 Grade B 2 Ø13 Grade
l=1.32
420 1 1.33 Grade 420 2
4.33 3 l=1.21
99
3 Ø13 Grade
l=1.21
420 18 Grade 420 2
26
Ø13 Grade 420
V1 2 l=1.32 P1 V2
0.0
66
19x14
35 2.65 35
A-A B-B
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 2
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 1
Pos. ReinforcementCode Shape Steel Number
1.99
26
0.0
66
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
5 Ø13 Grade
l=1.32
420 1 1.33 Grade 420 2
66
19x14
35 2.65 35
C-C D-D
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 5
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 2
Pos. ReinforcementCode Shape Steel Number
26
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
E F 6 Ø13 Grade
l=1.32
420 1 1.33 Grade 420 2
4.33
66
19x14
35 2.65 35
E-E F-F
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 6
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 3
Pos. ReinforcementCode Shape Steel Number
26
0.0
66
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
8 Ø13 Grade
l=1.68
420 1 1.68 Grade 420 2
66
19x14
35 2.65 35
G-G H-H
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 7
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 4
Pos. ReinforcementCode Shape Steel Number
26
0.0
70
1 Ø10 Gradel=98
300 T1 Grade 300 21
16
11
10 Ø13 Grade
l=1.71
420 1 1.71 Grade 420 2
70
20x14
35 2.80 35
I-I J-J
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.40 9
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 5
Pos. ReinforcementCode Shape Steel Number
2.10
26
0.0
70
1 Ø10 Gradel=98
300 T1 Grade 300 21
16
11
27
13 Ø13 Grade
l=1.40
420 1 1.40 Grade 420 2
14 Ø13 Grade
l=1.71
420 1 1.71 Grade 420 2
Ø13 Grade 420 Ø13 Grade 420
V6 11 l=30.58 13 l=1.40 P6 V7
15 Ø13 Grade
l=1.75
420 1 1.75 Grade 420 2
0.0
70
20x14
35 2.80 35
K-K L-L
Ø13 Grade 420
l=1.75 15
Ø13 Grade 420 Ø13 Grade 420
l=31.08 12 l=31.08 12
Ø10 Grade 300 Ø10 Grade 300
30
30
l=98 1 l=98 1
Ø13 Grade 420 Ø13 Grade 420
l=30.58 11 l=30.58 11
Ø13 Grade 420
20 l=1.40 13 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 6
Pos. ReinforcementCode Shape Steel Number
26
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
M N 16 Ø13 Grade
l=1.32
420 1 1.33 Grade 420 2
4.33
66
19x14
35 2.65 35
M-M N-N
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 16
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 7
Pos. ReinforcementCode Shape Steel Number
26
0.0
66
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
18 Ø13 Grade
l=1.68
420 1 1.68 Grade 420 2
66
19x14
35 2.65 35
O-O P-P
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 17
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 8
Pos. ReinforcementCode Shape Steel Number
26
0.0
66
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
20 Ø13 Grade
l=1.68
420 1 1.68 Grade 420 2
66
19x14
35 2.65 35
Q-Q R-R
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 19
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 9
Pos. ReinforcementCode Shape Steel Number
1.98
26
0.0
66
1 Ø10 Gradel=98
300 T1 Grade 300 20
16
11
S 420
Ø13 Grade T Ø13 Grade 420 21 Ø13 Grade
l=1.32
420 1 1.33 Grade 420 2
22 l=1.68 23 l=1.22 4.33
22 Ø13 Grade
l=1.68
420 1 1.68 Grade 420 2
26
23 Ø13 Grade
l=1.22
420 18 Grade 420 2
99
Ø13 Grade 420
W0 21 l=1.32 P10 W1
0.0
66 19x14
35 2.65 35
S-S T-T
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.32 21
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:25
Section scale 1:10 Page 10
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
1 Level:
⦁ Name : Level +0.00
⦁ Reference level : 4.33 (m)
⦁ Fire rating : 0 (h)
2.2 Geometry:
2.2.1 Span Position L.supp. L R.supp.
(m) (m) (m)
P1 Span 0.35 2.88 0.20
Span length: Lo = 3.15 (m)
Section from 0.00 to 2.88 (m)
200.00 x 300.00 (mm)
without left slab
without right slab
-30
-20
-10
10
20
30
40
[m]
50
0 2 4 6 8 10 12
Bending Moment ULS: Mu Mu,rd fi*Mn
100
[kN]
80
60
40
20
-20
-40
-60
-80
[m]
-100
0 2 4 6 8 10 12
Shear Force ULS: Vu Vu,rd fi*(Vc+Vs) fi*Vn
600
[mm2]
400
200
200
400
[m]
600
0 2 4 6 8 10 12
Reinforcement Area for Bending: As/As' Ast,red As,min As,des Ast
1500
[mm2/m]
1000
500
500
1000
[m]
1500
0 2 4 6 8 10 12
Reinforcement Area for Shear: Av Av,min Av,hang
2.4.5 Deflections
d(L) - initial live-load deflection
d(D) - initial dead-load deflection
d(LS) - initial sustained live-load deflection
d(LT) - total sustained live-load deflection
d(LT),lim - allowable deflection
-0.02
-0.01
0.01
0.02
[m]
0.03
0 2 4 6 8 10 12
Deflections: d_s(D+LS) d_l(D+LS) d_s(D+L) d(LT) d(LT),lim
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
0.35 10.16 0.00
0.49 9.15 0.00
0.81 6.86 0.00
1.12 4.57 0.00
1.44 2.29 0.00
1.75 -0.00 0.00
2.07 -2.29 0.00
2.38 -4.57 0.00
2.70 -6.86 0.00
3.01 -9.15 0.00
3.23 -10.71 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
3.43 17.51 0.00
3.98 14.46 0.00
4.63 10.84 0.00
5.28 7.23 0.00
5.93 3.61 0.00
6.58 -0.00 0.00
7.23 -3.61 0.00
7.88 -7.23 0.00
8.53 -10.84 0.00
9.18 -14.46 0.00
9.73 -17.51 0.00
ULS SLS
Abscissa Vu,max. Vu,max.
(m) (kN) (kN)
9.93 10.71 0.00
10.14 9.15 0.00
10.46 6.86 0.00
10.77 4.57 0.00
11.09 2.29 0.00
11.40 -0.00 0.00
11.72 -2.29 0.00
12.03 -4.57 0.00
Date : 30/08/23 Page : 4
Autodesk Robot Structural Analysis Professional 2019
Author: MOCHAMMAD AVI FEBRIANSYAH File: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG.rtd
Address: Project: GEDUNG INDUSTRI & PABRIK ROKOK
JABUNG
2.6 Reinforcement:
2.6.1 P1 : Span from 0.35 to 3.23 (m)
Longitudinal reinforcement:
⦁ bottom (Grade 420)
2 13 l = 1.44 from 2.51 to 1.07
⦁ support (Grade 420)
2 13 l = 1.27 from 0.03 to 0.03
Transversal reinforcement:
⦁ main (Grade 300)
stirrups 24 10 l = 0.98
e = 1*0.00 + 23*0.13 (m)
3 Material survey:
⦁ Concrete volume = 0.79 (m3)
⦁ Formwork = 10.42 (m2)
16
11
-33
0.0
2 Ø13 Grade
l=1.44
420 1 1.44 Grade 420 2
A Grade 420 B
4.33 3 Ø13
l=1.27 3 Ø13 Grade
l=1.27
420 18
1.05
Grade 420 2
26
Ø13 Grade 420
V1 2 l=1.44P1 V2
0.0
72
23x13
35 2.88 20
A-A B-B
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.44 2
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:50
Section scale 1:10 Page 1
Pos. ReinforcementCode Shape Steel Number
26
1 Ø10 Gradel=98
300 T1 Grade 300 50
16
11
4.73
-92
0.0
4 Ø13 Grade
l=13.08
420 1 13.08 Grade 420 2
C 420 Ø13 Grade 420 D
4.337 Ø13 Grade
l=2.49 5 l=13.58 7
Ø13 Grade 420
l=2.49 5 Ø13 Grade
l=13.58
420 17
13.11
Grade 420 2
27
6 Ø13 Grade
l=3.15
420 1 3.15 Grade 420 2
1.57
0.0
49x13
20 6.30 20
C-C D-D
Ø13 Grade 420
l=2.49 7
Ø13 Grade 420 Ø13 Grade 420
l=13.58 5 l=13.58 5
Ø10 Grade 300 Ø10 Grade 300
30
30
l=98 1 l=98 1
Ø13 Grade 420 Ø13 Grade 420
l=13.08 4 l=13.08 4
Ø13 Grade 420
20 l=3.15 6 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:50
Section scale 1:10 Page 2
Pos. ReinforcementCode Shape Steel Number
26
1 Ø10 Gradel=98
300 T1 Grade 300 22
16
11
2.15
0.0
8 Ø13 Grade
l=1.44
420 1 1.44 Grade 420 2
E F Ø13 Grade 4204.33 26
9 9 Ø13 Grade
l=1.27
420 18 Grade 420 2
1.05
l=1.27
0.0
72
21x14
20 2.88 35
E-E F-F
30
l=98 1 l=98 1
Ø13 Grade 420
l=1.44 8
20 20
GEDUNG INDUSTRI & PABRIK ROKOK JABUNG Section 200x300 View scale 1:50
Section scale 1:10 Page 3
Autodesk Robot Structural Analysis Professional 2019
GENERAL
Connection no.: 1
Connection name: Frame knee
Structure node: 326
Structure bars: 261, 263
GEOMETRY
COLUMN
Section: WF 250x125x6
Bar no.: 261
= -90.0 [Deg] Inclination angle
hc = 250.000 [mm] Height of column section
bfc = 125.000 [mm] Width of column section
twc = 6.000 [mm] Thickness of the web of column section
tfc = 9.000 [mm] Thickness of the flange of column section
rc = 8.000 [mm] Radius of column section fillet
Ac = 3697.000 [mm2] Cross-sectional area of a column
4
Ixc = 39600000.000 [mm ] Moment of inertia of the column section
Material: STEEL
fyc = 248211.34 [kPa] Resistance
BEAM
Section: WF 250x125x6
Bar no.: 263
= 19.5 [Deg] Inclination angle
hb = 250.000 [mm] Height of beam section
bf = 125.000 [mm] Width of beam section
= 19.5 [Deg] Inclination angle
twb = 6.000 [mm] Thickness of the web of beam section
tfb = 9.000 [mm] Thickness of the flange of beam section
rb = 8.000 [mm] Radius of beam section fillet
rb = 8.000 [mm] Radius of beam section fillet
Ab = 3697.000 [mm2] Cross-sectional area of a beam
Ixb = 39600000.000 [mm4] Moment of inertia of the beam section
Material: STEEL
fyb = 248211.34 [kPa] Resistance
BOLTS
The shear plane passes through the UNTHREADED portion of the bolt.
d= 15.875 [mm] Bolt diameter
Class = A307 Bolt class
FtRd = 58.99 [kN] Tensile resistance of a bolt
nh = 2 Number of bolt columns
nv = 3 Number of bolt rows
h1 = 50.750 [mm] Distance between first bolt and upper edge of front plate
Horizontal spacing ei = 70.000 [mm]
Vertical spacing pi = 60.000;60.000 [mm]
PLATE
hp = 430.000 [mm] Plate height
bp = 125.000 [mm] Plate width
tp = 20.000 [mm] Plate thickness
Material: SN400
fyp = 235000.00 [kPa] Resistance
LOWER STIFFENER
wd = 125.000 [mm] Plate width
tfd = 12.000 [mm] Flange thickness
hd = 140.000 [mm] Plate height
twd = 8.000 [mm] Web thickness
ld = 300.000 [mm] Plate length
= 40.4 [Deg] Inclination angle
Material: SN400
fybu = 235000.00 [kPa] Resistance
COLUMN STIFFENER
Upper
hsu = 232.000 [mm] Stiffener height
bsu = 59.500 [mm] Stiffener width
thu = 8.000 [mm] Stiffener thickness
Material: SN400
fysu = 235000.00 [kPa] Resistance
Lower
hsd = 232.000 [mm] Stiffener height
bsd = 59.500 [mm] Stiffener width
thd = 8.000 [mm] Stiffener thickness
Material: SN400
fysu = 235000.00 [kPa] Resistance
FILLET WELDS
aw = 5.000 [mm] Web weld
af = 7.000 [mm] Flange weld
aw = 5.000 [mm] Web weld
as = 5.000 [mm] Stiffener weld
afd = 5.000 [mm] Horizontal weld
MATERIAL FACTORS
M0 = 1.00 Partial safety factor [2.2]
M1 = 1.00 Partial safety factor [2.2]
M2 = 1.25 Partial safety factor [2.2]
M3 = 1.25 Partial safety factor [2.2]
LOADS
Ultimate limit state
Case: 11: COMB2 (BAJA) 1.2D+1.6L (1+2)*1.20+3*1.60
Mb1,Ed = 3.99 [kN*m] Bending moment in the right beam
Vb1,Ed = 7.60 [kN] Shear force in the right beam
Nb1,Ed = -6.52 [kN] Axial force in the right beam
Mc1,Ed = 3.99 [kN*m] Bending moment in the lower column
Vc1,Ed = 6.52 [kN] Shear force in the lower column
Nc1,Ed = -7.60 [kN] Axial force in the lower column
RESULTS
BEAM RESISTANCES
COMPRESSION
Ab = 3697.000 [mm2] Area EN1993-1-1:[6.2.4]
Ncb,Rd = Ab fyb / M0
Ncb,Rd = 917.64 [kN] Design compressive resistance of the section EN1993-1-1:[6.2.4]
SHEAR
Avb = 2765.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
Vcb,Rd = Avb (fyb / 3) / M0
Vcb,Rd = 396.24 [kN] Design sectional resistance for shear EN1993-1-1:[6.2.6.(2)]
Vb1,Ed / Vcb,Rd ≤ 1,0 0.02 < 1.00 verified (0.02)
BENDING - PLASTIC MOMENT (WITHOUT BRACKETS)
Wplb = 317000.000 [mm3] Plastic section modulus EN1993-1-1:[6.2.5.(2)]
Mb,pl,Rd = Wplb fyb / M0
Mb,pl,Rd = 78.68 [kN*m] Plastic resistance of the section for bending (without stiffeners) EN1993-1-1:[6.2.5.(2)]
BENDING ON THE CONTACT SURFACE WITH PLATE OR CONNECTED ELEMENT
Wpl = 813494.880 [mm3] Plastic section modulus EN1993-1-1:[6.2.5]
Mcb,Rd = Wpl fyb / M0
Mcb,Rd = 201.92 [kN*m] Design resistance of the section for bending EN1993-1-1:[6.2.5]
FLANGE AND WEB - COMPRESSION
Mcb,Rd = 201.92 [kN*m] Design resistance of the section for bending EN1993-1-1:[6.2.5]
hf = 392.611 [mm] Distance between the centroids of flanges [6.2.6.7.(1)]
Fc,fb,Rd = Mcb,Rd / hf
Fc,fb,Rd = 514.30 [kN] Resistance of the compressed flange and web [6.2.6.7.(1)]
WEB OR BRACKET FLANGE - COMPRESSION - LEVEL OF THE BEAM BOTTOM FLANGE
Bearing:
= 19.5 [Deg] Angle between the front plate and the beam
= 40.4 [Deg] Inclination angle of the bracket plate
beff,c,wb = 138.545 [mm] Effective width of the web for compression [6.2.6.2.(1)]
2
Avb = 1645.000 [mm ] Shear area EN1993-1-1:[6.2.6.(3)]
= 0.87 Reduction factor for interaction with shear [6.2.6.2.(1)]
com,Ed = 12646.88 [kPa] Maximum compressive stress in web [6.2.6.2.(2)]
= 19.5 [Deg] Angle between the front plate and the beam
kwc = 1.00 Reduction factor conditioned by compressive stresses [6.2.6.2.(2)]
Fc,wb,Rd1 = [ kwc beff,c,wb twb fyb / M0] cos() / sin( - )
Fc,wb,Rd1 = 383.10 [kN] Beam web resistance [6.2.6.2.(1)]
Buckling:
dwb = 216.000 [mm] Height of compressed web [6.2.6.2.(1)]
p = 0.95 Plate slenderness of an element [6.2.6.2.(1)]
= 0.83 Reduction factor for element buckling [6.2.6.2.(1)]
Fc,wb,Rd2 = [ kwc beff,c,wb twb fyb / M1] cos() / sin( - )
Fc,wb,Rd2 = 319.16 [kN] Beam web resistance [6.2.6.2.(1)]
Final resistance:
Fc,wb,Rd,low = Min (Fc,wb,Rd1 , Fc,wb,Rd2)
Fc,wb,Rd,low = 319.16 [kN] Beam web resistance [6.2.6.2.(1)]
COLUMN RESISTANCES
WEB PANEL - SHEAR
Mb1,Ed = 3.99 [kN*m] Bending moment (right beam) [5.3.(3)]
Mb2,Ed = 0.00 [kN*m] Bending moment (left beam) [5.3.(3)]
Vc1,Ed = 6.52 [kN] Shear force (lower column) [5.3.(3)]
Vc2,Ed = 0.00 [kN] Shear force (upper column) [5.3.(3)]
z= 326.636 [mm] Lever arm [6.2.5]
Vwp,Ed = (Mb1,Ed - Mb2,Ed) / z - (Vc1,Ed - Vc2,Ed) / 2
Vwp,Ed = 8.96 [kN] Shear force acting on the web panel [5.3.(3)]
Avs = 1645.000 [mm2] Shear area of the column web EN1993-1-1:[6.2.6.(3)]
Avc = 1645.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
ds = 402.000 [mm] Distance between the centroids of stiffeners [6.2.6.1.(4)]
Mpl,fc,Rd = 0.63 [kN*m] Plastic resistance of the column flange for bending [6.2.6.1.(4)]
Mpl,stu,Rd = 0.47 [kN*m] Plastic resistance of the upper transverse stiffener for bending [6.2.6.1.(4)]
Mpl,stl,Rd = 0.47 [kN*m] Plastic resistance of the lower transverse stiffener for bending [6.2.6.1.(4)]
Vwp,Rd = 0.9 ( Avs*fy,wc ) / (3 M0) + Min(4 Mpl,fc,Rd / ds , (2 Mpl,fc,Rd + Mpl,stu,Rd + Mpl,stl,Rd) / ds)
Vwp,Rd = 217.63 [kN] Resistance of the column web panel for shear [6.2.6.1]
Vwp,Ed / Vwp,Rd ≤ 1,0 0.04 < 1.00 verified (0.04)
WEB - TRANSVERSE COMPRESSION - LEVEL OF THE BEAM BOTTOM FLANGE
Bearing:
twc = 6.000 [mm] Effective thickness of the column web [6.2.6.2.(6)]
beff,c,wc = 160.547 [mm] Effective width of the web for compression [6.2.6.2.(1)]
Avc = 1645.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
= 0.83 Reduction factor for interaction with shear [6.2.6.2.(1)]
com,Ed = 12939.61 [kPa] Maximum compressive stress in web [6.2.6.2.(2)]
kwc = 1.00 Reduction factor conditioned by compressive stresses [6.2.6.2.(2)]
As = 952.000 [mm2] Area of the web stiffener EN1993-1-1:[6.2.4]
Fc,wc,Rd1 = kwc beff,c,wc twc fyc / M0 + As fys / M0
Fc,wc,Rd1 = 422.57 [kN] Column web resistance [6.2.6.2.(1)]
Buckling:
dwc = 216.000 [mm] Height of compressed web [6.2.6.2.(1)]
p = 1.02 Plate slenderness of an element [6.2.6.2.(1)]
= 0.79 Reduction factor for element buckling [6.2.6.2.(1)]
s = 5.84 Stiffener slenderness EN1993-1-1:[6.3.1.2]
s = 1.00 Buckling coefficient of the stiffener EN1993-1-1:[6.3.1.2]
Fc,wc,Rd2 = kwc beff,c,wc twc fyc / M1 + As s fys / M1
Fc,wc,Rd2 = 380.54 [kN] Column web resistance [6.2.6.2.(1)]
Final resistance:
Fc,wc,Rd,low = Min (Fc,wc,Rd1 , Fc,wc,Rd2)
Fc,wc,Rd = 380.54 [kN] Column web resistance [6.2.6.2.(1)]
WEB - TRANSVERSE COMPRESSION - LEVEL OF THE BEAM TOP FLANGE
Bearing:
twc = 6.000 [mm] Effective thickness of the column web [6.2.6.2.(6)]
beff,c,wc = 154.348 [mm] Effective width of the web for compression [6.2.6.2.(1)]
Avc = 1645.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
= 0.84 Reduction factor for interaction with shear [6.2.6.2.(1)]
com,Ed = 12939.61 [kPa] Maximum compressive stress in web [6.2.6.2.(2)]
kwc = 1.00 Reduction factor conditioned by compressive stresses [6.2.6.2.(2)]
As = 952.000 [mm2] Area of the web stiffener EN1993-1-1:[6.2.4]
Fc,wc,Rd1 = kwc beff,c,wc twc fyc / M0 + As fys / M0
Fc,wc,Rd1 = 417.16 [kN] Column web resistance [6.2.6.2.(1)]
Buckling:
dwc = 216.000 [mm] Height of compressed web [6.2.6.2.(1)]
p = 1.00 Plate slenderness of an element [6.2.6.2.(1)]
= 0.80 Reduction factor for element buckling [6.2.6.2.(1)]
s = 5.84 Stiffener slenderness EN1993-1-1:[6.3.1.2]
s = 1.00 Buckling coefficient of the stiffener EN1993-1-1:[6.3.1.2]
Fc,wc,Rd2 = kwc beff,c,wc twc fyc / M1 + As s fys / M1
Fc,wc,Rd2 = 378.56 [kN] Column web resistance [6.2.6.2.(1)]
Final resistance:
Fc,wc,Rd,upp = Min (Fc,wc,Rd1 , Fc,wc,Rd2)
Fc,wc,Rd,upp = 378.56 [kN] Column web resistance [6.2.6.2.(1)]
WELD RESISTANCE
Aw = 8224.364 [mm2] Area of all welds [4.5.3.2(2)]
Awy = 4690.000 [mm2] Area of horizontal welds [4.5.3.2(2)]
Awz = 3534.364 [mm2] Area of vertical welds [4.5.3.2(2)]
Iwy = 171935522.978 [mm4] Moment of inertia of the weld arrangement with respect to the hor. axis [4.5.3.2(5)]
max=max = -4202.58 [kPa] Normal stress in a weld [4.5.3.2(6)]
= = -3845.49 [kPa] Stress in a vertical weld [4.5.3.2(5)]
II = 2149.72 [kPa] Tangent stress [4.5.3.2(5)]
w = 0.80 Correlation coefficient [4.5.3.2(7)]
[max2 + 3*(max2)] ≤ fu/(w*M2) 8405.15 < 360000.00 verified (0.02)
2 2 2
[ + 3*( +II )] ≤ fu/(w*M2) 8544.89 < 360000.00 verified (0.02)
≤ 0.9*fu/M2 4202.58 < 259200.00 verified (0.02)
CONNECTION STIFFNESS
twash = 4.000 [mm] Washer thickness [6.2.6.3.(2)]
hhead = 12.000 [mm] Bolt head height [6.2.6.3.(2)]
hnut = 15.875 [mm] Bolt nut height [6.2.6.3.(2)]
Lb = 50.938 [mm] Bolt length [6.2.6.3.(2)]
k10 = 6.221 [mm] Stiffness coefficient of bolts [6.3.2.(1)]
STIFFNESSES OF BOLT ROWS
Nr hj k3 k4 k5 keff,j keff,j hj keff,j hj2
Sum 838.340 258827.621
1 356.636 2.114 4.566 47.022 1.144 408.024 145515.872
2 296.636 1.086 2.346 23.631 0.645 191.394 56774.180
3 236.636 1.819 3.929 39.335 1.010 238.922 56537.569
keff,j = 1 / (∑35 (1 / ki,j)) [6.3.3.1.(2)]
zeq = ∑j keff,j hj2 / ∑j keff,j hj
zeq = 308.738 [mm] Equivalent force arm [6.3.3.1.(3)]
keq = ∑j keff,j hj / zeq
keq = 2.715 [mm] Equivalent stiffness coefficient of a bolt arrangement [6.3.3.1.(1)]
2
Avc = 1645.000 [mm ] Shear area EN1993-1-1:[6.2.6.(3)]
= 1.00 Transformation parameter [5.3.(7)]
z= 308.738 [mm] Lever arm [6.2.5]
k1 = 2.025 [mm] Stiffness coefficient of the column web panel subjected to shear [6.3.2.(1)]
k2 = Stiffness coefficient of the compressed column web [6.3.2.(1)]
Sj,ini = E zeq2 / ∑i (1 / k1 + 1 / k2 + 1 / keq) [6.3.1.(4)]
Sj,ini = 22105.61 [kN*m] Initial rotational stiffness [6.3.1.(4)]
= 1.00 Stiffness coefficient of a connection [6.3.1.(6)]
Sj = Sj,ini / [6.3.1.(4)]
Sj = 22105.61 [kN*m] Final rotational stiffness [6.3.1.(4)]
Connection classification due to stiffness.
Sj,rig = 9328.05 [kN*m] Stiffness of a rigid connection [5.2.2.5]
Sj,pin = 583.00 [kN*m] Stiffness of a pinned connection [5.2.2.5]
Sj,ini Sj,rig RIGID
WEAKEST COMPONENT:
COLUMN FLANGE - TENSION
REMARKS
Distance of bolts from an edge is too large. 259.250 [mm] > 120.000 [mm]
GENERAL
Connection no.: 2
Connection name: Beam-Beam
Structure node: 328
Structure bars: 263, 264
GEOMETRY
LEFT SIDE
BEAM
Section: WF 250x125x6
Bar no.: 263
= -160.5 [Deg] Inclination angle
hbl = 250.000 [mm] Height of beam section
bfbl = 125.000 [mm] Width of beam section
twbl = 6.000 [mm] Thickness of the web of beam section
tfbl = 9.000 [mm] Thickness of the flange of beam section
rbl = 8.000 [mm] Radius of beam section fillet
Abl = 3697.000 [mm2] Cross-sectional area of a beam
Ixbl = 39600000.000 [mm4] Moment of inertia of the beam section
Material: STEEL
fyb = 248211.34 [kPa] Resistance
RIGHT SIDE
BEAM
Section: WF 250x125x6
Bar no.: 264
= -19.5 [Deg] Inclination angle
hbr = 250.000 [mm] Height of beam section
bfbr = 125.000 [mm] Width of beam section
twbr = 6.000 [mm] Thickness of the web of beam section
tfbr = 9.000 [mm] Thickness of the flange of beam section
rbr = 8.000 [mm] Radius of beam section fillet
Abr = 3697.000 [mm2] Cross-sectional area of a beam
Ixbr = 39600000.000 [mm4] Moment of inertia of the beam section
Material: STEEL
fyb = 248211.34 [kPa] Resistance
BOLTS
The shear plane passes through the UNTHREADED portion of the bolt.
d= 15.875 [mm] Bolt diameter
Class = A307 Bolt class
FtRd = 58.99 [kN] Tensile resistance of a bolt
nh = 2 Number of bolt columns
nv = 5 Number of bolt rows
h1 = 50.750 [mm] Distance between first bolt and upper edge of front plate
Horizontal spacing ei = 70.000 [mm]
Vertical spacing pi = 35.000;35.000;70.000;35.000 [mm]
PLATE
hpr = 430.000 [mm] Plate height
bpr = 125.000 [mm] Plate width
tpr = 20.000 [mm] Plate thickness
Material: SN400
fypr = 235000.00 [kPa] Resistance
LOWER STIFFENER
wrd = 125.000 [mm] Plate width
tfrd = 10.000 [mm] Flange thickness
hrd = 140.000 [mm] Plate height
twrd = 6.000 [mm] Web thickness
lrd = 300.000 [mm] Plate length
d = 8.0 [Deg] Inclination angle
Material: SN400
fybu = 235000.00 [kPa] Resistance
FILLET WELDS
aw = 5.000 [mm] Web weld
af = 7.000 [mm] Flange weld
afd = 5.000 [mm] Horizontal weld
MATERIAL FACTORS
M0 = 1.00 Partial safety factor [2.2]
M1 = 1.00 Partial safety factor [2.2]
M2 = 1.25 Partial safety factor [2.2]
M3 = 1.25 Partial safety factor [2.2]
LOADS
Ultimate limit state
Case: 11: COMB2 (BAJA) 1.2D+1.6L (1+2)*1.20+3*1.60
Mb1,Ed = -2.55 [kN*m] Bending moment in the right beam
Nb1,Ed = -7.84 [kN] Axial force in the right beam
RESULTS
BEAM RESISTANCES
COMPRESSION
Ab = 3697.000 [mm2] Area EN1993-1-1:[6.2.4]
Ncb,Rd = Ab fyb / M0
Ncb,Rd = 917.64 [kN] Design compressive resistance of the section EN1993-1-1:[6.2.4]
BENDING - PLASTIC MOMENT (WITHOUT BRACKETS)
3
Wplb = 317000.000 [mm ] Plastic section modulus EN1993-1-1:[6.2.5.(2)]
Mb,pl,Rd = Wplb fyb / M0
Mb,pl,Rd = 78.68 [kN*m] Plastic resistance of the section for bending (without stiffeners) EN1993-1-1:[6.2.5.(2)]
BENDING ON THE CONTACT SURFACE WITH PLATE OR CONNECTED ELEMENT
3
Wpl = 708441.499 [mm ] Plastic section modulus EN1993-1-1:[6.2.5]
Mcb,Rd = Wpl fyb / M0
Mcb,Rd = 175.84 [kN*m] Design resistance of the section for bending EN1993-1-1:[6.2.5]
FLANGE AND WEB - COMPRESSION
Mcb,Rd = 175.84 [kN*m] Design resistance of the section for bending EN1993-1-1:[6.2.5]
hf = 395.436 [mm] Distance between the centroids of flanges [6.2.6.7.(1)]
Fc,fb,Rd = Mcb,Rd / hf
Fc,fb,Rd = 444.68 [kN] Resistance of the compressed flange and web [6.2.6.7.(1)]
WEB OR BRACKET FLANGE - COMPRESSION - LEVEL OF THE BEAM BOTTOM FLANGE
Bearing:
= 19.5 [Deg] Angle between the front plate and the beam
= 8.0 [Deg] Inclination angle of the bracket plate
beff,c,wb = 126.438 [mm] Effective width of the web for compression [6.2.6.2.(1)]
Avb = 1645.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
= 0.89 Reduction factor for interaction with shear [6.2.6.2.(1)]
com,Ed = 0.00 [kPa] Maximum compressive stress in web [6.2.6.2.(2)]
kwc = 1.00 Reduction factor conditioned by compressive stresses [6.2.6.2.(2)]
Fc,wb,Rd1 = [ kwc beff,c,wb twb fyb / M0] cos() / sin( - )
Fc,wb,Rd1 = 357.14 [kN] Beam web resistance [6.2.6.2.(1)]
Buckling:
dwb = 216.000 [mm] Height of compressed web [6.2.6.2.(1)]
p = 0.90 Plate slenderness of an element [6.2.6.2.(1)]
= 0.86 Reduction factor for element buckling [6.2.6.2.(1)]
Fc,wb,Rd2 = [ kwc beff,c,wb twb fyb / M1] cos() / sin( - )
Fc,wb,Rd2 = 307.55 [kN] Beam web resistance [6.2.6.2.(1)]
Final resistance:
Fc,wb,Rd,low = Min (Fc,wb,Rd1 , Fc,wb,Rd2)
Fc,wb,Rd,low = 307.55 [kN] Beam web resistance [6.2.6.2.(1)]
CONNECTION STIFFNESS
twash = 4.000 [mm] Washer thickness [6.2.6.3.(2)]
hhead = 12.000 [mm] Bolt head height [6.2.6.3.(2)]
hnut = 15.875 [mm] Bolt nut height [6.2.6.3.(2)]
Lb = 50.938 [mm] Bolt length [6.2.6.3.(2)]
k10 = 6.221 [mm] Stiffness coefficient of bolts [6.3.2.(1)]
STIFFNESSES OF BOLT ROWS
Nr hj k3 k4 k5 keff,j keff,j hj keff,j hj2
Sum 2461.252 390863.441
1 210.975 35.188 4.596 969.673 204577.060
2 175.975 20.677 3.884 683.503 120279.621
3 105.975 20.677 3.884 411.617 43621.242
4 70.975 13.785 3.270 232.079 16471.894
5 35.975 34.412 4.569 164.380 5913.624
5
keff,j = 1 / (∑3 (1 / ki,j)) [6.3.3.1.(2)]
zeq = ∑j keff,j hj2 / ∑j keff,j hj
zeq = 158.807 [mm] Equivalent force arm [6.3.3.1.(3)]
keq = ∑j keff,j hj / zeq
keq = 15.498 [mm] Equivalent stiffness coefficient of a bolt arrangement [6.3.3.1.(1)]
2
Sj,ini = E zeq keq [6.3.1.(4)]
Sj,ini = 78152.37 [kN*m] Initial rotational stiffness [6.3.1.(4)]
= 1.00 Stiffness coefficient of a connection [6.3.1.(6)]
Sj = Sj,ini / [6.3.1.(4)]
Sj = 78152.37 [kN*m] Final rotational stiffness [6.3.1.(4)]
Connection classification due to stiffness.
Sj,rig = 9328.05 [kN*m] Stiffness of a rigid connection [5.2.2.5]
Sj,pin = 583.00 [kN*m] Stiffness of a pinned connection [5.2.2.5]
Sj,ini Sj,rig RIGID
WEAKEST COMPONENT:
BEAM WEB - TENSION
REMARKS
Distance of bolts from an edge is too large. 204.250 [mm] > 120.000 [mm]
Bolts vertical spacing is too small. 35.000 [mm] < 37.125 [mm]
GENERAL
Connection no.: 3
Connection name: Fixed column base
Structure node: 323
Structure bars: 261
GEOMETRY
COLUMN
Section: WF 250x125x6
Bar no.: 261
Lc = 1.30 [m] Column length
= 0.0 [Deg] Inclination angle
hc = 250.000 [mm] Height of column section
bfc = 125.000 [mm] Width of column section
twc = 6.000 [mm] Thickness of the web of column section
tfc = 9.000 [mm] Thickness of the flange of column section
rc = 8.000 [mm] Radius of column section fillet
Ac = 3697.000 [mm2] Cross-sectional area of a column
Iyc = 39600000.000 [mm4] Moment of inertia of the column section
Material: STEEL
fyc = 248211.34 [kPa] Resistance
fuc = 399896.05 [kPa] Yield strength of a material
COLUMN BASE
lpd = 325.000 [mm] Length
bpd = 325.000 [mm] Width
tpd = 10.000 [mm] Thickness
Material: SS400
fypd = 235000.00 [kPa] Resistance
fupd = 360000.00 [kPa] Yield strength of a material
ANCHORAGE
The shear plane passes through the UNTHREADED portion of the bolt.
Class = A307 Anchor class
fyb = 248211.26 [kPa] Yield strength of the anchor material
fub = 413685.44 [kPa] Tensile strength of the anchor material
d= 19.050 [mm] Bolt diameter
As = 285.161 [mm2] Effective section area of a bolt
Av = 285.023 [mm2] Area of bolt section
nH = 2 Number of bolt columns
nV = 2 Number of bolt rows
Horizontal spacing eHi = 100.000 [mm]
Vertical spacing eVi = 80.000 [mm]
Anchor dimensions
L1 = 55.000 [mm]
L2 = 640.000 [mm]
L3 = 50.000 [mm]
L4 = 95.000 [mm]
Washer
lwd = 40.000 [mm] Length
bwd = 50.000 [mm] Width
twd = 10.000 [mm] Thickness
STIFFENER
ws = 300.000 [mm] Width
hs = 250.000 [mm] Height
ts = 20.000 [mm] Thickness
d1 = 20.000 [mm] Cut
d2 = 20.000 [mm] Cut
MATERIAL FACTORS
M0 = 1.00 Partial safety factor
M2 = 1.25 Partial safety factor
C = 1.50 Partial safety factor
SPREAD FOOTING
L= 350.000 [mm] Spread footing length
B= 350.000 [mm] Spread footing width
H= 6400.000 [mm] Spread footing height
Concrete
Class CONCR Fc24
fck = 24000.00 [kPa] Characteristic resistance for compression
Grout layer
tg = 10.000 [mm] Thickness of leveling layer (grout)
fck,g = 12000.00 [kPa] Characteristic resistance for compression
Cf,d = 0.30 Coeff. of friction between the base plate and concrete
WELDS
ap = 3.000 [mm] Footing plate of the column base
as = 4.000 [mm] Stiffeners
LOADS
Case: 16: COMB7 (BAJA) 1.2D+1Ex+1L (1+2)*1.20+(8+3)*1.00
Nj,Ed = -6.05 [kN] Axial force
Vj,Ed,y = 0.02 [kN] Shear force
Vj,Ed,z = -5.40 [kN] Shear force
Mj,Ed,y = -5.20 [kN*m] Bending moment
Mj,Ed,z = 0.02 [kN*m] Bending moment
RESULTS
COMPRESSION ZONE
COMPRESSION OF CONCRETE
fcd = 16000.00 [kPa] Design compressive resistance EN 1992-1:[3.1.6.(1)]
fj = 11487.18 [kPa] Design bearing resistance under the base plate [6.2.5.(7)]
c = tp (fyp/(3*fj*M0))
c= 26.114 [mm] Additional width of the bearing pressure zone [6.2.5.(4)]
beff = 61.227 [mm] Effective width of the bearing pressure zone under the flange [6.2.5.(3)]
leff = 177.227 [mm] Effective length of the bearing pressure zone under the flange [6.2.5.(3)]
2
Ac0 = 10851.121 [mm ] Area of the joint between the base plate and the foundation EN 1992-1:[6.7.(3)]
Ac1 = 38150.000 [mm2] Maximum design area of load distribution EN 1992-1:[6.7.(3)]
Frdu = Ac0*fcd*(Ac1/Ac0) ≤ 3*Ac0*fcd
Frdu = 325.54 [kN] Bearing resistance of concrete EN 1992-1:[6.7.(3)]
j = 0.67 Reduction factor for compression [6.2.5.(7)]
fjd = j*Frdu/(beff*leff)
fjd = 20000.40 [kPa] Design bearing resistance [6.2.5.(7)]
2
Ac,n = 54665.333 [mm ] Bearing area for compression [6.2.8.2.(1)]
2
Ac,y = 22098.834 [mm ] Bearing area for bending My [6.2.8.3.(1)]
Ac,z = 22098.834 [mm2] Bearing area for bending Mz [6.2.8.3.(1)]
Fc,Rd,i = AC,i*fjd
Fc,Rd,n = 1093.33 [kN] Bearing resistance of concrete for compression [6.2.8.2.(1)]
Fc,Rd,y = 441.99 [kN] Bearing resistance of concrete for bending My [6.2.8.3.(1)]
Fc,Rd,z = 441.99 [kN] Bearing resistance of concrete for bending Mz [6.2.8.3.(1)]
COLUMN FLANGE AND WEB IN COMPRESSION
CL = 1.00 Section class EN 1993-1-1:[5.5.2]
3
Wpl,y = 1122000.000 [mm ] Plastic section modulus EN1993-1-1:[6.2.5.(2)]
Mc,Rd,y = 278.49 [kN*m] Design resistance of the section for bending EN1993-1-1:[6.2.5]
hf,y = 241.000 [mm] Distance between the centroids of flanges [6.2.6.7.(1)]
Fc,fc,Rd,y = Mc,Rd,y / hf,y
Fc,fc,Rd,y = 1155.57 [kN] Resistance of the compressed flange and web [6.2.6.7.(1)]
3
Wpl,z = 790750.000 [mm ] Plastic section modulus EN1993-1-1:[6.2.5.(2)]
Mc,Rd,z = 196.27 [kN*m] Design resistance of the section for bending EN1993-1-1:[6.2.5]
hf,z = 168.722 [mm] Distance between the centroids of flanges [6.2.6.7.(1)]
Fc,fc,Rd,z = Mc,Rd,z / hf,z
Fc,fc,Rd,z = 1163.29 [kN] Resistance of the compressed flange and web [6.2.6.7.(1)]
RESISTANCES OF SPREAD FOOTING IN THE COMPRESSION ZONE
Nj,Rd = Fc,Rd,n
Nj,Rd = 1093.33 [kN] Resistance of a spread footing for axial compression [6.2.8.2.(1)]
FC,Rd,y = min(Fc,Rd,y,Fc,fc,Rd,y)
FC,Rd,y = 441.99 [kN] Resistance of spread footing in the compression zone [6.2.8.3]
FC,Rd,z = min(Fc,Rd,z,Fc,fc,Rd,z)
FC,Rd,z = 441.99 [kN] Resistance of spread footing in the compression zone [6.2.8.3]
TENSION ZONE
STEEL FAILURE
Ab = 285.161 [mm2] Effective anchor area [Table 3.4]
fub = 413685.44 [kPa] Tensile strength of the anchor material [Table 3.4]
Beta = 0.85 Reduction factor of anchor resistance [3.6.1.(3)]
Ft,Rd,s1 = beta*0.9*fub*Ab/M2
Ft,Rd,s1 = 72.20 [kN] Anchor resistance to steel failure [Table 3.4]
Ms = 1.20 Partial safety factor CEB [3.2.3.2]
fyb = 248211.26 [kPa] Yield strength of the anchor material CEB [9.2.2]
Ft,Rd,s2 = fyb*Ab/Ms
Ft,Rd,s2 = 58.98 [kN] Anchor resistance to steel failure CEB [9.2.2]
Ft,Rd,s = min(Ft,Rd,s1,Ft,Rd,s2)
Ft,Rd,s = 58.98 [kN] Anchor resistance to steel failure
PULL-OUT FAILURE
fck = 24000.00 [kPa] Characteristic compressive strength of concrete EN 1992-1:[3.1.2]
fctd = 0.7*0.3*fck2/3/C
fctd = 1164.85 [kPa] Design tensile resistance EN 1992-1:[8.4.2.(2)]
1 = 1.00 Coeff. related to the quality of the bond conditions and concreting conditions EN 1992-1:[8.4.2.(2)]
2 = 1.00 Coeff. related to the bar diameter EN 1992-1:[8.4.2.(2)]
fbd = 2.25*1*2*fctd
fbd = 2620.91 [kPa] Design value of the ultimate bond stress EN 1992-1:[8.4.2.(2)]
hef = 640.000 [mm] Effective anchorage depth EN 1992-1:[8.4.2.(2)]
Ft,Rd,p = *d*hef*fbd
Ft,Rd,p = 100.39 [kN] Design uplift capacity EN 1992-1:[8.4.2.(2)]
CONCRETE CONE FAILURE
hef = 90.000 [mm] Effective anchorage depth CEB [9.2.4]
0 0.5 0.5 1.5
NRk,c = 7.5[N /mm ]*fck*hef
0
NRk,c = 31.37 [kN] Characteristic resistance of an anchor CEB [9.2.4]
scr,N = 270.000 [mm] Critical width of the concrete cone CEB [9.2.4]
ccr,N = 135.000 [mm] Critical edge distance CEB [9.2.4]
2
Ac,N0 = 129500.000 [mm ] Maximum area of concrete cone CEB [9.2.4]
Ac,N = 122500.000 [mm2] Actual area of concrete cone CEB [9.2.4]
A,N = Ac,N/Ac,N0
A,N = 0.95 Factor related to anchor spacing and edge distance CEB [9.2.4]
c= 125.000 [mm] Minimum edge distance from an anchor CEB [9.2.4]
s,N = 0.7 + 0.3*c/ccr.N ≤ 1.0
s,N = 0.98 Factor taking account the influence of edges of the concrete member on the distribution of stresses in the concrete CEB [9.2.4
ec,N = 1.00 Factor related to distribution of tensile forces acting on anchors CEB [9.2.4
re,N = 0.5 + hef[mm]/200 ≤ 1.0
re,N = 1.00 Shell spalling factor CEB [9.2.4]
ucr,N = 1.00 Factor taking into account whether the anchorage is in cracked or non-cracked concrete CEB [9.2.4]
Mc = 2.16 Partial safety factor CEB [3.2.3.1]
Ft,Rd,c = NRk,c0*A,N*s,N*ec,N*re,N*ucr,N/Mc
Ft,Rd,c = 13.43 [kN] Design anchor resistance to concrete cone failure EN 1992-1:[8.4.2.(2)]
SPLITTING FAILURE
hef = 640.000 [mm] Effective anchorage depth CEB [9.2.5]
0 0.5 0.5 1.5
NRk,c = 7.5[N /mm ]*fck*hef
NRk,c0 = 594.89 [kN] Design uplift capacity CEB [9.2.5]
scr,N = 1280.000 [mm] Critical width of the concrete cone CEB [9.2.5]
ccr,N = 640.000 [mm] Critical edge distance CEB [9.2.5]
Ac,N0 = 1876800.000 [mm2] Maximum area of concrete cone CEB [9.2.5]
Ac,N = 122500.000 [mm2] Actual area of concrete cone CEB [9.2.5]
A,N = Ac,N/Ac,N0
A,N = 0.07 Factor related to anchor spacing and edge distance CEB [9.2.5]
c= 125.000 [mm] Minimum edge distance from an anchor CEB [9.2.5]
s,N = 0.7 + 0.3*c/ccr.N ≤ 1.0
s,N = 0.76 Factor taking account the influence of edges of the concrete member on the distribution of stresses in the concrete CEB [9.2.5
s,N = 0.76 Factor taking account the influence of edges of the concrete member on the distribution of stresses in the concrete CEB [9.2.5
ec,N = 1.00 Factor related to distribution of tensile forces acting on anchors CEB [9.2.5
re,N = 0.5 + hef[mm]/200 ≤ 1.0
re,N = 1.00 Shell spalling factor CEB [9.2.5]
ucr,N = 1.00 Factor taking into account whether the anchorage is in cracked or non-cracked concrete CEB [9.2.5]
2/3
h,N = (h/(2*hef)) ≤ 1.2
h,N = 1.20 Coeff. related to the foundation height CEB [9.2.5]
M,sp = 2.16 Partial safety factor CEB [3.2.3.1]
0
Ft,Rd,sp = NRk,c *A,N*s,N*ec,N*re,N*ucr,N*h,N/M,sp
Ft,Rd,sp = 16.36 [kN] Design anchor resistance to splitting of concrete CEB [9.2.5]
TENSILE RESISTANCE OF AN ANCHOR
Ft,Rd = min(Ft,Rd,s , Ft,Rd,p , Ft,Rd,c , Ft,Rd,sp)
Ft,Rd = 13.43 [kN] Tensile resistance of an anchor
BENDING OF THE BASE PLATE
Bending moment Mj,Ed,y
leff,1 = 162.437 [mm] Effective length for a single bolt for mode 1 [6.2.6.5]
leff,2 = 162.437 [mm] Effective length for a single bolt for mode 2 [6.2.6.5]
m= 33.606 [mm] Distance of a bolt from the stiffening edge [6.2.6.5]
Mpl,1,Rd = 0.95 [kN*m] Plastic resistance of a plate for mode 1 [6.2.4]
Mpl,2,Rd = 0.95 [kN*m] Plastic resistance of a plate for mode 2 [6.2.4]
FT,1,Rd = 113.59 [kN] Resistance of a plate for mode 1 [6.2.4]
FT,2,Rd = 40.17 [kN] Resistance of a plate for mode 2 [6.2.4]
FT,3,Rd = 26.87 [kN] Resistance of a plate for mode 3 [6.2.4]
Ft,pl,Rd,y = min(FT,1,Rd , FT,2,Rd , FT,3,Rd)
Ft,pl,Rd,y = 26.87 [kN] Tension resistance of a plate [6.2.4]
Bending moment Mj,Ed,z
leff,1 = 162.437 [mm] Effective length for a single bolt for mode 1 [6.2.6.5]
leff,2 = 162.437 [mm] Effective length for a single bolt for mode 2 [6.2.6.5]
m= 33.606 [mm] Distance of a bolt from the stiffening edge [6.2.6.5]
Mpl,1,Rd = 0.95 [kN*m] Plastic resistance of a plate for mode 1 [6.2.4]
Mpl,2,Rd = 0.95 [kN*m] Plastic resistance of a plate for mode 2 [6.2.4]
FT,1,Rd = 113.59 [kN] Resistance of a plate for mode 1 [6.2.4]
FT,2,Rd = 40.17 [kN] Resistance of a plate for mode 2 [6.2.4]
FT,3,Rd = 26.87 [kN] Resistance of a plate for mode 3 [6.2.4]
Ft,pl,Rd,z = min(FT,1,Rd , FT,2,Rd , FT,3,Rd)
Ft,pl,Rd,z = 26.87 [kN] Tension resistance of a plate [6.2.4]
TENSILE RESISTANCE OF A COLUMN WEB
Bending moment Mj,Ed,y
twc = 6.000 [mm] Effective thickness of the column web [6.2.6.3.(8)]
beff,t,wc = 162.437 [mm] Effective width of the web for tension [6.2.6.3.(2)]
Avc = 1645.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
= 0.83 Reduction factor for interaction with shear [6.2.6.3.(4)]
Ft,wc,Rd,y = beff,t,wc twc fyc / M0
Ft,wc,Rd,y = 200.46 [kN] Column web resistance [6.2.6.3.(1)]
Bending moment Mj,Ed,z
twc = 6.000 [mm] Effective thickness of the column web [6.2.6.3.(8)]
beff,t,wc = 162.437 [mm] Effective width of the web for tension [6.2.6.3.(2)]
Avc = 1645.000 [mm2] Shear area EN1993-1-1:[6.2.6.(3)]
= 0.83 Reduction factor for interaction with shear [6.2.6.3.(4)]
Ft,wc,Rd,z = beff,t,wc twc fyc / M0
Ft,wc,Rd,z = 200.46 [kN] Column web resistance [6.2.6.3.(1)]
RESISTANCES OF SPREAD FOOTING IN THE TENSION ZONE
FT,Rd,y = min(Ft,pl,Rd,y,Ft,wc,Rd,y)
FT,Rd,y = 26.87 [kN] Resistance of a column base in the tension zone [6.2.8.3]
FT,Rd,z = min(Ft,pl,Rd,z,Ft,wc,Rd,z)
FT,Rd,z = 26.87 [kN] Resistance of a column base in the tension zone [6.2.8.3]
CONNECTION CAPACITY CHECK
Nj,Ed / Nj,Rd ≤ 1,0 (6.24) 0.01 < 1.00 verified (0.01)
ey = 859.872 [mm] Axial force eccentricity [6.2.8.3]
zc,y = 120.500 [mm] Lever arm FC,Rd,y [6.2.8.1.(2)]
zt,y = 50.000 [mm] Lever arm FT,Rd,y [6.2.8.1.(3)]
Mj,Rd,y = 5.33 [kN*m] Connection resistance for bending [6.2.8.3]
Mj,Ed,y / Mj,Rd,y ≤ 1,0 (6.23) 0.98 < 1.00 verified (0.98)
ez = 3.667 [mm] Axial force eccentricity [6.2.8.3]
zc,z = 84.361 [mm] Lever arm FC,Rd,z [6.2.8.1.(2)]
zt,z = 40.000 [mm] Lever arm FT,Rd,z [6.2.8.1.(3)]
Mj,Rd,z = 3.11 [kN*m] Connection resistance for bending [6.2.8.3]
Mj,Ed,z / Mj,Rd,z ≤ 1,0 (6.23) 0.01 < 1.00 verified (0.01)
Mj,Ed,y / Mj,Rd,y + Mj,Ed,z / Mj,Rd,z ≤ 1,0 0.98 < 1.00 verified (0.98)
SHEAR
BEARING PRESSURE OF AN ANCHOR BOLT ONTO THE BASE PLATE
Shear force Vj,Ed,y
d,y = 1.94 Coeff. taking account of the bolt position - in the direction of shear [Table 3.4]
b,y = 1.00 Coeff. for resistance calculation F1,vb,Rd [Table 3.4]
k1,y = 2.50 Coeff. taking account of the bolt position - perpendicularly to the direction of shear [Table 3.4]
F1,vb,Rd,y = k1,y*b,y*fup*d*tp / M2
F1,vb,Rd,y = 137.16 [kN] Resistance of an anchor bolt for bearing pressure onto the base plate [6.2.2.(7)]
Shear force Vj,Ed,z
d,z = 1.78 Coeff. taking account of the bolt position - in the direction of shear [Table 3.4]
b,z = 1.00 Coeff. for resistance calculation F1,vb,Rd [Table 3.4]
k1,z = 2.50 Coeff. taking account of the bolt position - perpendicularly to the direction of shear [Table 3.4]
F1,vb,Rd,z = k1,z*b,z*fup*d*tp / M2
F1,vb,Rd,z = 137.16 [kN] Resistance of an anchor bolt for bearing pressure onto the base plate [6.2.2.(7)]
SHEAR OF AN ANCHOR BOLT
b = 0.37 Coeff. for resistance calculation F2,vb,Rd [6.2.2.(7)]
Avb = 285.023 [mm2] Area of bolt section [6.2.2.(7)]
fub = 413685.44 [kPa] Tensile strength of the anchor material [6.2.2.(7)]
M2 = 1.25 Partial safety factor [6.2.2.(7)]
F2,vb,Rd = b*fub*Avb/M2
F2,vb,Rd = 34.48 [kN] Shear resistance of a bolt - without lever arm [6.2.2.(7)]
M = 2.00 Factor related to the fastening of an anchor in the foundation CEB [9.3.2.2]
MRk,s = 0.20 [kN*m] Characteristic bending resistance of an anchor CEB [9.3.2.2]
lsm = 24.525 [mm] Lever arm length CEB [9.3.2.2]
Ms = 1.20 Partial safety factor CEB [3.2.3.2]
Fv,Rd,sm = M*MRk,s/(lsm*Ms)
Fv,Rd,sm = 13.79 [kN] Shear resistance of a bolt - with lever arm CEB [9.3.1]
CONCRETE PRY-OUT FAILURE
NRk,c = 29.02 [kN] Design uplift capacity CEB [9.2.4]
k3 = 2.00 Factor related to the anchor length CEB [9.3.3]
Mc = 2.16 Partial safety factor CEB [3.2.3.1]
Fv,Rd,cp = k3*NRk,c/Mc
Fv,Rd,cp = 26.87 [kN] Concrete resistance for pry-out failure CEB [9.3.1]
CONCRETE EDGE FAILURE
Shear force Vj,Ed,y
0
VRk,c,y = 127.39 [kN] Characteristic resistance of an anchor CEB [9
A,V,y = 0.62 Factor related to anchor spacing and edge distance CE
h,V,y = 1.00 Factor related to the foundation thickness CEB [
s,V,y = 0.89 Factor related to the influence of edges parallel to the shear load direction CEB [9
0
VRk,c,y = 127.39 [kN] Characteristic resistance of an anchor CEB [9
ec,V,y = 1.00 Factor taking account a group effect when different shear loads are acting on the individual anchors in a group CEB [9
,V,y = 1.00 Factor related to the angle at which the shear load is applied CEB [
ucr,V,y = 1.00 Factor related to the type of edge reinforcement used CEB [9
Mc = 2.16 Partial safety factor CEB
Fv,Rd,c,y = VRk,c,y0*A,V,y*h,V,y*s,V,y*ec,V,y*,V,y*ucr,V,y/Mc
Fv,Rd,c,y = 32.23 [kN] Concrete resistance for edge failure CEB [9.3.1]
Shear force Vj,Ed,z
0
VRk,c,z = 113.50 [kN] Characteristic resistance of an anchor CEB [9
A,V,z = 0.72 Factor related to anchor spacing and edge distance CE
h,V,z = 1.00 Factor related to the foundation thickness CEB [
s,V,z = 0.92 Factor related to the influence of edges parallel to the shear load direction CEB [9
ec,V,z = 1.00 Factor taking account a group effect when different shear loads are acting on the individual anchors in a group CEB [9
,V,z = 1.00 Factor related to the angle at which the shear load is applied CEB [
ucr,V,z = 1.00 Factor related to the type of edge reinforcement used CEB [9
Mc = 2.16 Partial safety factor CEB
0
Fv,Rd,c,z = VRk,c,z *A,V,z*h,V,z*s,V,z*ec,V,z*,V,z*ucr,V,z/Mc
Fv,Rd,c,z = 34.66 [kN] Concrete resistance for edge failure CEB [9.3.1]
SPLITTING RESISTANCE
Cf,d = 0.30 Coeff. of friction between the base plate and concrete [6.2.2.(6)]
Nc,Ed = 6.05 [kN] Compressive force [6.2.2.(6)]
Ff,Rd = Cf,d*Nc,Ed
Ff,Rd = 1.81 [kN] Slip resistance [6.2.2.(6)]
SHEAR CHECK
Vj,Rd,y = nb*min(F1,vb,Rd,y, F2,vb,Rd, Fv,Rd,sm, Fv,Rd,cp, Fv,Rd,c,y) + Ff,Rd
Vj,Rd,y = 56.99 [kN] Connection resistance for shear CEB [9.3.1]
Vj,Ed,y / Vj,Rd,y ≤ 1,0 0.00 < 1.00 verified (0.00)
Vj,Rd,z = nb*min(F1,vb,Rd,z, F2,vb,Rd, Fv,Rd,sm, Fv,Rd,cp, Fv,Rd,c,z) + Ff,Rd
Vj,Rd,z = 56.99 [kN] Connection resistance for shear CEB [9.3.1]
Vj,Ed,z / Vj,Rd,z ≤ 1,0 0.09 < 1.00 verified (0.09)
Vj,Ed,y / Vj,Rd,y + Vj,Ed,z / Vj,Rd,z ≤ 1,0 0.10 < 1.00 verified (0.10)
STIFFENER CHECK
Stiffener perpendicular to the web (along the extension of the column flanges)
M1 = 0.54 [kN*m] Bending moment acting on a stiffener
Q1 = 10.78 [kN] Shear force acting on a stiffener
zs = 103.113 [mm] Location of the neutral axis (from the plate base)
Is = 46781623.428 [mm4] Moment of inertia of a stiffener
d = 1072.92 [kPa] Normal stress on the contact surface between stiffener and plate EN 1993-1-1:[6.2.1.(5)]
g = 1807.77 [kPa] Normal stress in upper fibers EN 1993-1-1:[6.2.1.(5)]
= 2156.22 [kPa] Tangent stress in a stiffener EN 1993-1-1:[6.2.1.(5)]
z = 3885.75 [kPa] Equivalent stress on the contact surface between stiffener and plate EN 1993-1-1:[6.2.1.(5)]
max (g, / (0.58), z ) / (fyp/M0) ≤ 1.0 (6.1) 0.02 < 1.00 verified (0.02)
CONNECTION STIFFNESS
Bending moment Mj,Ed,y
beff = 61.227 [mm] Effective width of the bearing pressure zone under the flange [6.2.5.(3)]
leff = 177.227 [mm] Effective length of the bearing pressure zone under the flange [6.2.5.(3)]
k13,y = Ec*(beff*leff)/(1.275*E)
k13,y = 9.263 [mm] Stiffness coeff. of compressed concrete [Table 6.11]
leff = 162.437 [mm] Effective length for a single bolt for mode 2 [6.2.6.5]
m= 33.606 [mm] Distance of a bolt from the stiffening edge [6.2.6.5]
3 3
k15,y = 0.850*leff*tp /(m )
k15,y = 3.638 [mm] Stiffness coeff. of the base plate subjected to tension [Table 6.11]
Lb = 191.925 [mm] Effective anchorage depth [Table 6.11]
k16,y = 1.6*Ab/Lb
k16,y = 2.377 [mm] Stiffness coeff. of an anchor subjected to tension [Table 6.11]
0,y = 0.14 Column slenderness [5.2.2.5.(2)]
Sj,ini,y = 2913.99 [kN*m] Initial rotational stiffness [Table 6.12]
Sj,rig,y = 182721.73 [kN*m] Stiffness of a rigid connection [5.2.2.5]
Sj,ini,y < Sj,rig,y SEMI-RIGID [5.2.2.5.(2)]
Bending moment Mj,Ed,z
k13,z = Ec*(Ac,z)/(1.275*E)
k13,z = 13.219 [mm] Stiffness coeff. of compressed concrete [Table 6.11]
leff = 162.437 [mm] Effective length for a single bolt for mode 2 [6.2.6.5]
m= 33.606 [mm] Distance of a bolt from the stiffening edge [6.2.6.5]
k15,z = 0.850*leff*tp3/(m3)
k15,z = 3.638 [mm] Stiffness coeff. of the base plate subjected to tension [Table 6.11]
Lb = 191.925 [mm] Effective anchorage depth [Table 6.11]
k16,z = 1.6*Ab/Lb
k16,z = 2.377 [mm] Stiffness coeff. of an anchor subjected to tension [Table 6.11]
0,z = 0.52 Column slenderness [5.2.2.5.(2)]
Sj,ini,z = 37620.06 [kN*m] Initial rotational stiffness [6.3.1.(4)]
Sj,rig,z = 13565.70 [kN*m] Stiffness of a rigid connection [5.2.2.5]
Sj,ini,z Sj,rig,z RIGID [5.2.2.5.(2)]
WEAKEST COMPONENT:
FOUNDATION - CONCRETE CONE PULL-OUT FAILURE
REMARKS
Anchor curvature radius is too small. 25.000 [mm] < 57.150 [mm]
Segment L4 of the hook anchor is too short. 95.000 [mm] < 95.250 [mm]