Secara garis besar tahapan analisis dan disain struktur adalah sebagai berikut :
• Pengumpulan data : Layout bangunan, dimensi struktur (kolom, plat, balok )
dan fungsi bangunan.
• Membuat dan merancang pemodelan bangunan
• Menghitung dan memasukan data struktur
• Menganalisa struktur
• Menentukan gaya dalam yang terjadi, penulangan, Drawing dan report.
• Membuat kesimpulan dari model struktur bangunan tersebut
Tahapan Analisa Struktur dengan Robot Struktural Analysis
START
Preferences
Setting / Tools
Job Preferences
Sections
Properties
Thickness
Axis Definition
Column
Stories
MODEL
Beam
Section
Slab
Support
Braces
Load Types
Load Definition
LOAD Wind Loads Simulation
Seismic Load
Load Combination
• Analysis Types
Analyze
• Calculation
Design
Report
➢ Data Struktur :
• Dimensi Struktur : 15 x 9 x 7
• Tinggi perLantai = 3,5 m
• Kolom (WF) : 400x400x11x18 (W16x89)
• Balok (WF) : 350x350x10x16 (W14x74)
• Bracing : (L) 152 x 152 x 15.9 (L 6x6x0.5)
• Mutu Baja : A992
• Slab, fc 25 MPa : Tebal 12 cm
➢ Pembebanan :
• Slab : Beban mati : DL = 288 kg/m2 ; Beban Hidup : LL = 250 kg/m2
• Beam : DL = 290 Kg/m
➢ Beban Angin :
▪ Kecepatan Angin (Wind Speed) = 20 m/s
▪ Tekanan angin otomatis dihitung oleh ROBOT
➢ Beban Gempa :
Respon Spectrum :
▪ Gempa : Gempa Jogja
Sistem Rangka Pemikul Momen Biasa : R (Faktor Modifikasi) = 3
Gedung Perkantoran : II (Faktor Keutamaan) = 1
▪ Kelas Situs : SD (Tanah Sedang)
➢ Kombinasi Pembebanan :
▪ 1,2 DL + 1,6 LL
▪ 1,2 DL + 1 LL + 1 EQ
▪ 1,2 DL + 1 LL + 1 W
▪ 0,9 DL + 1 EQ
▪ 0,9 DL + 1 W
➢ Tampilan Robot
2) Setting / Tools
➢ Preferences
➢ Job Preferences
3) Properties
➢ Sections : Geometry → Properties → Sections
4) Modeling
➢ Axis Definition : Geometry → Axis Definition
• Tampilan : PLAN
• Tampilan : VIEW
➢ Draw Sections
• Columns : Geometry → Columns
• Copy : Edit → Edit → Move / Copy
6) Release :
➢ Edit → Select
➢ Geometry → Releases
7) Loads
➢ Load Types
➢ Load Definition
• Dead Load : DL 2
Beam (Balok)
➢ Wind Load :
• Geometry → Object → Polyline – Contour
• Seismic Load :
o Load to mass conversion :
o Analysis → Analysis Type → New
• Load Combination :
Loads → Automatic Combination
Manual combinations - generate
8) Analysis
➢ Calculation
➢ Verification
9) Results
➢ Diagrams for Bars
Forces
Deformation
➢ Maps on Bars
➢ DESIGN
Design → Steel Member Design
➢ CONNECTIONS DESIGN
o Design → Steel Connection Design
o New Connection for Selected Bars