No :
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
METHODE STATEMENT
INSTALLATION PIPING HYDRANT AND SPRINKLER
Rev.
Date Status Revision Details
No.
Approval
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
1. INTRODUCTION 1. PEMBUKAAN
This work describes methods for the purpose of Metode kerja ini menjelaskan tujuan untuk
installation piping well carried on in accordance with pemasangan pipa di laksanakan dengan baik sesuai
the standard of work and occupational safety. dengan standard kerja dan keselamatan kerja.
2. TUJUAN
2. INTRODUCTION
Metode kerja ini berlaku untuk semua orang yang
This working method is applicable to all the people
terlibat dan bertanggung jawab dalam pekerjaan
involved and responsible for the work so that the
tersebut sehingga para pekerja dapat memahami
worker can understand what they are going to do to
apa saja yang akan mereka kerjakan dengan tetap
continue prioritizing safety.
mengutamakan keselamatan kerja.
5. PROCESS 5. PROSES
5.1. Installation piping all area 5.1. Instalasi Pipa Semua Area
5.1.1 Preparation 5.1.1 Persiapan
- Prepare drawing has been approved by - Persiapkan gambar yang sudah disetujui oleh
consultan.
konsultan sesuai jenis pekerjaan.
- Prepare equipment and material required
before doing the work. - Persiapkan peralatan dan material yang
- Ensure that PPE workers have been completed
dibutuhkan sebelum melakukan pekerjaan.
prior to starting the job.
- Pastikan APD pekerja telah di lengkapi sebelum
memulai pekerjaan.
Doc. No :
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
- When finished using the threaded, the end of the - Setelah selesai di senai menggunakan mesin
pipe at the cleaned using liquid detergent and senai, ujung pipa di bersihkan menggunakan
then rinsed with water and wipe with a dry cloth. sabun cair lalu dibilas dengan air dan keringkan
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
- Welding the pipe ends to connect pipes Sch 40 - Untuk pipa yang akan di las yaitu mulai ≥ 50A,
BSP ASTM A53 Grade A-ERW using the cek bevel pada ujung pipa yang akan dilas
SMAW-API 5L Grade A welding wire with a size menggunakan welding gauge.
of between 2.6mm-3.2mm (According - Las pada ujung pipa untuk menyambung pipa
WPS/TEP/API/ 2015). BSP ASTM A53 Sch 40 Grade A-ERW
- Check the result of a welding. menggunakan SMAW-API 5L-Grade A dengan
- Give the paint of zink cromate on the welding ukuran kawat las antara 2.6mm-3.2mm (Sesuai
point are checked. WPS/TEP/API/2015).
- Perform each end of the closure pipe flange - Cek hasil sambungan las tadi.
wear cap+seal type or using flange before - Beri cat zink cromate pada titik las yang sudah di
testing. cek.
- Do the pressure test until 1.5 x Nominal pressure - Lakukan penutupan disetiap ujung pipa memakai
pump during 2 Hours and make sure Zero dop+seal type atau menggunakan flange
Pressure Drop. sebelum melakukan pengetesan.
- Perform flushing using compressed air and - Lakukan pengetesan tekanan hingga 1.5 x
water to clean the inner side of the pipe from dirt nominal pressure pompa selama 2 jam dan
gram pipe. pastikan tidak ada penurunan tekanan.
- Remove the cap and remove screw using a wire - Lakukan flushing menggunakan udara
brush (wire brush). bertekanan dan air untuk membersihkan sisi
- Give finishing paint accordance with the type of bagian dalam pipa dari gram pipa.
pipe is Color for Hydrant and sprinkler. - Lepas semua dop dan berisihkan ulir
- Install sprinkler head, valve and alarm check menggunakan sikat kawat (wire brush).
valve vertical trim by way of then wrapped the - Beri cat finish sesuai dengan approval warna
wool (cotton rope) which is then closed using a untuk pipa hydrant dan sprinkler.
seal tape (PTFE) and then smearing screw with - Install sprinkler head, valve dan alarm check
paint (as adhesive) and. Corresponding pairs of valve vertical trim dengan cara melilitkan benang
images, see the appendix. wol (cotton rope) yang kemudian ditutup
menggunakan seal tape (PTFE) serta melumuri
ulir dengan cat (sebagai perekat) lalu. Pasang
sesuai gambar, lihat lampiran.
Doc. No :
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
6. MONITORING 6. MONITORING
- The work area should be free and there should - Area kerja harus bebas dan tidak boleh ada
be no unauthorized people enter. orang lain yang tidak berkepentingan masuk.
- Use PPE Standards on entry to the work area - Gunakan APD Standar pada saat masuk ke
and use the full body hardness with shock area kerja dan gunakan full body hardness with
absorber on work at height. shock absorber pada pekerjaan di ketinggian.
- Inspection every welded joints using welding log - Inspeksi setiap sambungan las menggunakan
and photo report any pipe welding performed by form welding Log dan foto report setiap welding
PIC-TIE pipa yang dilakukan oleh PIC-TIE
- Make a check on each connection using a screw - Lakukan pengecekan pada setiap sambungan
sprinkler head, valve and alarm check valve yang menggunakan ulir sprinkler head, valve
vertical trim and make sure there is no leakage dan alarm check valve vertical trim dan pastikan
during testing pressure. tidak ada kebocoran saat melakukan
- Ensure that all valves and accessories installed pengetesan tekanan.
according to the technical data (Alarm Check - Pastikan semua valve dan aksesoris terpasang
Valve Vertical Trim) that has been approved by sesuai technical data (Alarm Check Valve
the consultant. Vertical Trim) yang telah disetujui oleh
consultan.
7. EQUIPMENT 7. PERLENGKAPAN
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
9. PENANGGULANGAN BAHAYA
9. CONTROL MEASURE
- Membuat izin untuk pekerjaan ketinggian
- Create a work permit for height.
- Membuat daftar nama pekerja yang akan
- Make a list of names of workers who will do the
melakukan pekerjaan
job.
- Memeriksa pemakaian alat pelindung diri.
- Examine the use of personal protective
- Membuat tanda pada area yang sedang di
equipment.
kerjakan.
- Make a mark on the area that is being done.
Date : Rev : 0
RELAYOUT & DECOMMISSIONING LAYOUT PROJECT - IFF ESSENCE INDONESIA
10.4 SURVEYOR
Responsible for providing for the marking of pipe 10.4 SURVEYOR