Bab VII - Tekanan Kapiler
Bab VII - Tekanan Kapiler
81
82
2. .cos
Pc . g. h
r
Dimana :
Pc = tekanan kapiler
= tegangan permukaan antara dua fluida
cos = sudut kontak permukaan antara dua fluida
r = jari-jari lengkung pori-pori
= perbedaan densitas dua fluida
g = percepatan gravitasi
h = tinggi kolom
Dalam Persamaan diatas dapat dilihat bahwa tekanan kapiler
berhubungan dengan ketinggian di atas permukaan air bebas (oil-water
contact), sehingga data tekanan kapiler dapat dinyatakan menjadi plot
antara h versus saturasi air (Sw), seperti pada (Gambar 7.1).
Perubahan ukuran pori-pori dan densitas fluida akan mempengaruhi
bentuk kurva tekanan kapiler dan ketebalan zona transisi
83
Pc = w . g . h
Dimana :
Pa = tekanan udara, dyne/cm2
Pw = tekanan air, dyne/cm2
Pc = tekanan kapiler, dyne/cm2
ρw = densitas air, gr/cc
ρa = densitas udara, gr/cc
g = percepatan gravitasi, m/det2
h = tinggi kolom, m
86
Fa = AT . 2 . r (gaya keatas)
Fa = r2 . . g . h (gaya kebawah)
2σ𝑜𝑤 . cos 𝜃
= 𝑃𝑐
𝑟
Dimana :
2σ𝑜𝑤 . cos 𝜃
𝑃𝑐 =
𝑟
87
7.3.2. Bahan
1. Fresh Core.
2. Gas.
7.4. Prosedur Percobaan
7.4.1. Kalibrasi Alat
Yaitu untuk menentukan volume picnometer (28; 150 cc).
1. Pasang picnometer lid (4) pada tempatnya, pump metering plunger
diputar penuh dengan manipulasi handwheel.
93
Karena dalam penggunaan alat ini memakai tekanan yang besar tentu
akan terjadi perubahan volume picnometer dan mercury. Untuk itu perlu
dilakukan Pressure-Volume Correction yaitu :
1. Letakkan picnometer lid pada tempatnya, pump metering plunger
diputar penuh dengan memanipulasi handwheel.
2. Ubah panel valve ke vacuum juga small pressure gauge dibuka,
sistem dikosongkan sampai absolute pressure kurang dari 20 micro.
3. Mercury diinjeksikan sampai mencapai upper reference mark, adjust
moveable scale dan handwheel scale dial pada pembacaan 0,00 cc
kemudian tutup vacuum valve.
4. Putar bleed valve mercury turun 3 mm di bawah upper reference
mark.
5. Putar pompa hingga mercury mencapai upper reference mark lagi
dan biarkan stabil selama 30 detik.
6. Baca dan catat tekanan pada small pressure gauge serta hubungan
volume scale dan dial handwheel (gunakan dial) yang miring kekiri
sebagai pengganti 0-5 cc. Graduated interval pada skala.
94
8. Putar bleed valve, maka gas / udara mengalir ke sistem sampai level
mercury turun 3 sampai 5 mm di bawah upper reference mark.
9. Putar pompa sampai permukaan mercury mencapai tanda paling atas
dan usahakan konstan selama 30 detik.
10. Baca dan catat tekanan (low pressure gauge) dan volume scale
beserta handwheel dial (miring ke kiri) untuk mengganti 0-5 cc
graduated interval pada scale.
11. Step 8, 9, 10 diulang untuk beberapa kenaikkan tekanan. Jika
tekanan telah mencapai 1 atm buka nitrogen valve. Jika sistem telah
mencapai limit pada 0-2 atm gauge, gauge diisolasi dari sistem dan
gunakan 0-150 atm gauge.
12. Step 11 diulangi sampai tekanan akhir didapat.
13. Catatan : fluktuasi thermometer 1 – 2 oC.
14. Jika test telah selesai, nitrogen valve ditutup. Tekanan sistem
dikurangi sampai mencapai tekanan atm dengan mengeluarkan gas
lewat bleed valve.
Vp : 30 cc
1 0,15
4 0,25
9 0,35
15 0,4
25 0,45
35 0,48
40 0,49
50 0,5
60 0,51
100 0,54
110 0,56
120 0,59
125 0,62
128 0,64
130 0,67
131 0,69
132 0,71
133 0,74
134 0,77
135 0,8
136 0,83
137 0,87
139 0,99
140 1
7.5.2. Perhitungan
Sampel 1 :
98
Sampel 2 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 1,5 atm + 0,05 atm = 1,55 atm
Pressure Volume Correction = 0,167 cc
4
4 − 1,5 0,25 − x
2,5 =
4−1 0,25 − 0,15
1 2,5 0,25 − x
=
3 0,1
x = 0,167 cc
0,25 x 0,15
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 22,5 cc – 0,167 cc = 22,3333 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
22,333 cc
= x 100 % = 74,443 %
30 cc
99
Sampel 3 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 3, atm + 0,05 atm = 3,05 atm
Pressure Volume Correction = 0,2 cc
9
9−3 0,35 − x
3 =
9 − 1 0,35 − 0,15
1 6 0,35 − x
=
8 0,2
x = 0,2 cc
0,35 x 0,15
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 15 cc – 0,2 cc = 14,8 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
14,8 cc
= x 100 % = 49.333 %
30 cc
Sampel 4 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 4,5 atm + 0,05 atm = 4,55 atm
Pressure Volume Correction = 0,2375 cc
9
9 − 4,5 0,35 − x
4,5 =
9−3 0,35 − 0,2
3 4,5 0,35 − x
=
6 0,15
x = 0,2375 cc
0,35 x 0,2
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 15 cc – 0,22375 cc = 14,7625 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
14,7625 cc
= x 100 % = 49,208 %
30 cc
100
Sampel 5 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 6,5 atm + 0,05 atm = 6,55 atm
Pressure Volume Correction = 0,2875 cc
9
9 − 6,5 0,35 − x
6,5 =
9−3 0,35 − 0,2
3 2,5 0,35 − x
=
6 0,15
x = 0,2875 cc
0,35 x 0,2
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 13 cc – 0,2875 cc = 12,7125 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
12,7125 cc
= x 100 % = 42,375 %
30 cc
Sampel 6 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 8 atm + 0,05 atm = 8,05 atm
Pressure Volume Correction = 0,33 cc
9
9−8 0,35 − x
8 =
9 − 4 0,35 − 0,25
4 1 0,35 − x
=
5 0,1
x = 0,33 cc
0,35 x 0,25
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 10,333 cc – 0,33 cc = 10,337 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
10,337 cc
= x 100 % = 34,457 %
30 cc
101
Sampel 7 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 11,5 atm + 0,05 atm = 11,55 atm
Pressure Volume Correction = 0,37083 cc
15
15 − 11,5 0,4 − x
11,5 =
15 − 9 0,4 − 0,35
9 3,5 0,4 − x
=
6 0,05
x = 0,37083 cc
0,4 x 0,35
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 9,3 cc – 0,37083 cc = 8,929 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
8,929 cc
= x 100 % = 29,704 %
30 cc
Sampel 8 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 16 atm + 0,05 atm = 16,05 atm
Pressure Volume Correction = 0,405 cc
25
25 − 16 0,45 − x
16 =
25 − 15 0,45 − 0,4
15 9 0,45 − x
=
10 0,05
x = 0,405 cc
0,45 x 0,4
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 9 cc – 0,405 cc = 8,595 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
8,595cc
= x 100 % = 28,65 %
30 cc
102
Sampel 9 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 23 atm + 0,05 atm = 23,05 atm
Pressure Volume Correction = 0,44 cc
25
25 − 23 0,45 − x
23 =
25 − 15 0,45 − 0,4
15 2 0,45 − x
=
10 0,05
x = 0,44 cc
0,45 x 0,4
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 8,66 cc – 0,44 cc = 8,22 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
8,22 cc
= x 100 % = 27,4 %
30 cc
Sampel 10 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 36 atm + 0,05 atm = 36,05 atm
Pressure Volume Correction = 0,482 cc
40
40 − 36 0,49 − x
36 =
40 − 35 0,49 − 0,48
35 4 0,49 − x
=
5 0,01
x = 0,482 cc
0,49 x 0,48
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 8,6 cc – 0,482 cc = 8,118 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
8,118 cc
= x 100 % = 27,06 %
30 cc
103
Sampel 11 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 58 atm + 0,05 atm = 58,05 atm
Pressure Volume Correction = 0,508 cc
60
60 − 58 0,51 − x
58 =
60 − 50 0,51 − 0,5
50 2 0,51 − x
=
10 0,01
x = 0,508 cc
0,51 x 0,5
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 7,89 cc – 0,508 cc = 7,382 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
7,382 cc
= x 100 % = 24,60 %
30 cc
Sampel 12 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 75 atm + 0,05 atm = 75,05 atm
Pressure Volume Correction = 0,521 cc
100
100 − 75 0,54 − x
75 =
100 − 60 0,54 − 0,51
60 25 0,54 − x
=
40 0,03
x = 0,521 cc
0,54 x 0,51
Actual Volume1 of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 7,6 cc – 0,521 cc = 7,0787 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
7,0787 cc
= x 100 % = 23,59 %
30 cc
104
Sampel 13 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 80 atm + 0,05 atm = 80,05 atm
Pressure Volume Correction = 0,525 cc
100
100 − 80 0,54 − x
80 =
100 − 60 0,54 − 0,51
60 20 0,54 − x
=
40 0,03
x = 0,525 cc
Actual Volume
0,54 x of Mercury Injection
0,51
= Indicator volume of mercury injection–Pressure volume correction
= 7,4 cc – 0,525 cc = 6,875 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
6,875 cc
= x 100 % = 22,92 %
30 cc
Sampel 14 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 85,5 atm + 0,05 atm = 85,55 atm
Pressure Volume Correction = 0,529 cc
100
100 − 85,5 0,54 − x
85,5 =
100 − 60 0,54 − 0,51
60 14,5 0,54 − x
=
40 0,03
x = 0,529 cc
0,54 x 0,51
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 7 cc – 0,529 cc = 6,471cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
6,471 cc
= x 100 % = 21,57 %
30 cc
Sampel 15 :
105
Sampel 16 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 95 atm + 0,05 atm = 95,05 atm
Pressure Volume Correction = 0,535 cc
100
100 − 95 0,54 − x
95 =
100 − 90,5 0,54 − 0,53
90,5 5 0,54 − x
=
9,5 0,01
x = 0,535 cc
0,54 x 0,53
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 6,9 cc – 0,535 cc = 6,365 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
6,365 cc
= x 100 % = 21,22 %
30 cc
Sampel 17 :
106
Sampel 18 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 105 atm + 0,05 atm = 105,05 atm
Pressure Volume Correction = 0,55 cc
110
110 − 105 0,56 − x
105 =
110 − 100 0,56 − 0,54
100 5 0,56 − x
=
10 0,02
x = 0,55 cc
0,56 x 0,54
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 6,5 cc – 0,55 cc = 5,95 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
5,95 cc
= x 100 % = 19,83 %
30 cc
Sampel 19 :
107
Sampel 20 :
Correct Pressure = Indicator Pressure + 0,05 atm
= 120 atm + 0,05 atm = 120,05 atm
Pressure Volume Correction = 0,59 cc
125
125 − 120 0,62 − x
120 =
125 − 110 0,62 − 0,56
110 5 0,62 − x
=
15 0,06
x = 0,59 cc
0,62 x 0,56
Actual Volume of Mercury Injection
= Indicator volume of mercury injection–Pressure volume correction
= 6,3 cc – 0,59 cc = 5,71 cc
Actual volume of mercury injection
Mercury Saturation = x 100%
Vp
5,71 cc
= x 100 % = 19,03 %
30 cc
7.6. Pembahasan
108
19.83, 105.05
100 20.53, 100.55
21.22, 95.05
Correct Pressure (atm)
21.39, 90.55
21.57, 85.55
80 22.92, 80.05
23.59, 75.05
60 24.6, 58.05
40
27.06, 36.05
27.4, 23.05
20
28.65, 16.05
29.704, 11.55
34.457, 8.05 6.55
42.375,
49.208,
49.33, 4.55
3.05
0 74.443, 1.55
83, 0.55
0 20 40 60 80 100
Mercury Saturation (%)
Pressure Vs Volume
160
80
60 0.54, 60
0.51, 50
40 0.5, 40
0.49, 35
0.48, 25
20
0.45, 15
0.4, 9
0, 0 0.25, 1 0.35, 4
0 0.15, 0
0 0.2 0.4 0.6 0.8 1 1.2
Volume (cc)
110
7.7. Kesimpulan
1. Setelah melakukan percobaan dapat disimpulkan bahwa penentuan
tekanan kapiler dari suatu sampel formasi dapat dikatakan lebih cepat
dan efisien pada distribusi tertinggi saturasi fluidanya.
2. Dapat kita ketahui dari percobaan ini nilai dari pressure berbanding
lurus dengan volume. Semakin besar volume, maka nilai tekanan akan
semakin meningkat.
3. Indikator pressure berbanding terbalik dengan mercury saturation
yaitu dengan berkurangnya indikator pressure akan meningkatkan
mercury saturation.
4. Nilai dari correct pressure akan berbanding terbalik dengan nilai
mercury saturation.
5. Dari percobaan ini diperoleh adanya distribusi, maka akan terdapatnya
zona transisi karena tidak terdapat batas fluida yang jelas.