bertanggung jawab untuk mengawasi operasi pengeboran kontraktor seismik, kualitas Kedalaman,
kualitas Pengisian dinamit, kualitas Tamping, kualits equipment, kualitas safety equipment, kualitas
sdm, kualitas FFE dan semua aspek, memberi suport, saran perbaikan untuk operasi yang tidak
memenuhi standar kerja, memiliki tanggung jawab utama sebagai berikut:
responsible for supervising seismic contractor drilling operations, Depth quality, dynamite filling
quality, Tamping quality, equipment quality, safety equipment quality, human resource quality, FFE
quality and all aspects, providing support, suggestions for improvements for operations that do not
meet work standards, have responsibility main as follows:
1. Memastikan kepatuhan kontrak yang ditanda tangani antara Kontraktor seismik dan Perusahaan.
Ensuring the compliance of the contract signed between the seismic Contractor and the Company.
2. Mengawasi agar operasi pemboran dan pembuatan lubang tembak dilakukan dengan cara yang
aman, benar dan efisien, termasuk pada:
Supervise that drilling and shooting operations are carried out in a safe, correct and efficient manner,
including in:
3. Mengontrol dan memvalidasi, inspeksi fisik, kepatuhan dengan persyaratan untuk kedalaman
lubang tepat, dan pengisian dinamit memadai, Tamping sudah benar dan jarak aman sudah tepat.
Controlling and validating, physical inspection, compliance with requirements for proper bore depth,
and adequate dynamite filling, Tamping is correct and safety distances are correct.
4. Membantu dan mengamati aktivitas peledakan lubang tembak. Awasi dan periksa kembali laporan
ledakan dan anomali UH yang benar. Membantu QC memimpin departemen terkait (terutama
merekam), untuk menganalisis tren secara statistik, korelasi dengan litologi dan penyebab. Sarankan
tindakan perbaikan untuk kualitas dan produktivitas berdasarkan analisis aktivitas pengeboran.
Kualifikasi teknis yang sesuai dan pengalaman yang baik dalam bertindak sebagai pengawas
pengeboran pada kru seismik ekstensif dan langsung dengan:
Assist and observe firing hole blasting activity. Keep an eye on and double check the correct UH
explosion and anomaly reports. Helps QC lead related departments (especially record), to statistically
analyze trends, correlations with lithology and causes. Suggest corrective action for quality and
productivity based on analysis of drilling activity Appropriate technical qualifications and good
experience acting as drilling supervisor on an extensive and hands-on seismic crew with:
Masalah Air , contoh air terlaluh jauh atau masalah alam musim kemarau dll.
Water problems, for example the water is too far away or natural problems during the
dry season etc.
·Masalah Litologi, contoh , tanah keras kerikil dan batuan keras, area koral, bocor
lubang bor sehingga air boros, tanah lengket, area pasir runtuh sehingga lubang
macet
Lithological problems, for example, hard soil gravel and hard rock, coral areas,
leaking boreholes causing wasteful water, sticky soil, areas of sand collapsing so that
the hole is stuck
·Terlambatnya Transpotasi equpment, karna area gunung, bukit, rawa, line yang
tidak mempunyai bridging atau kondisi lintasan tidak bersih banyak batang kayu yang
tumbang atau rintisan tidak bagus.
The lateness of iqupment transportation, because the area of mountains, hills,
swamps, lines that do not have bridging or the condition of the track is not clean,
many logs have fallen or the stubs are not good.
Equipment harus standart, mesin power rig, mud pump, equipment harus
peralatan baru.
Equipment must be standard, power rig machine, mud pump, equipment mustnew
equipment.
Buat tandon air yang besar gunakan mobil tangki untuk transportasi air, gunakan
mesin water rellay .
For a large water reservoir, use a tank car for water transportation, use a water relay
machine.
Bila lubang bor macet sebelum disiisi bahan peledak lakukan re drill
If the drill hole gets stuck before being filled with explosives, do a re-drill
Bila lubang macet sesudah diisi contoh kabel putus detonator, dead cap kedalaman
tidak sesuai target lakukan bor lubang baru (B) minimal radius 5meter dari lubang
(A).
If the hole is stuck after being filled, for example, the detonator broken cable, the
dead cap depth is not according to the target, drill a new hole (B) with a radius of at
least 5 meters from the hole (A).
Lihat kondisi area titik lubang bor, bila tidak aman, contoh ada jembatan, rumah
beton, tiang listrik lakukan kompensasi kedapan atau kebelakang searah line, bila
tidak memungkinkan adanya kompensasi, lakukan offset ke kiri atau kanan, lakukan
pengurangan carge bila masih tidak aman.
Look at the condition of the shot hole point area, if it is not safe, for example there is a
bridge, a concrete house, a power pole, do a tight compensation or backward in the
direction of the line, if there is no possible compensation, offset it to the left or right,
reduce the carge if it is still not safe.
· Litologi/ Lithology
Gunakan matabor. Trifus untuk bantuan keras.
Gunakan tanah kering untuk menutupi lubang yang bocor/ leaking hole.
Untuk Sticky clay sebaiknya tidak gunakan mesin power rig, sebaiknya
gunakan flushing lakukan dengan mutar layang.
Pasir runtuh gunakan polimer agar bisa menahan sementara dinding lubang dari
keruntuhan.
area gravel gunakan cassing Hq atau Nq.
Bersihkan sekitar lubang bor Lakukan di titik potok merah menimal radius 5 meter.
Clean around the borehole. Do it at the point of red pot with a radius of at least 5
meters
untuk menghasil kan lubang yang bagus, lakukan bor lurus dan stabilkan posisi bor
tersebut, jangan lakukan bor miring.
to produce a good hole, drill straight and stabilize the position of the drill, do not drill
inclined.
Setelah 5-10 meter lakukan bor naik turun dan tahan sampai catting keluar semua
dari lubang dan lanjutkan mengebor begitu seterusnya sampai finish, setelah finis
tahan dan tunggu sekitar 5-10 menit, setela catting keluar semuanya matikan mesin
dan angkat pipa tersebut.
After 5-10 meters do the drill up and down and hold until the catting comes out of the
hole and continue drilling and so on until the finish, after finishing hold and wait for
about 5-10 minutes, after the catting comes out, turn off the engine and lift the pipe.
Setiap area litologi berbeda, pasir, tanah keras, tanah lengket, kerikil, untuk bor di
area pasir lakukan bor cepat dan harus air lumpur dan ditambahkan polimer/bintonik
untuk mengetalkan air slush pit tersebut supaya catting terangkat semua dan bisa
menahan diding lubang bor dari keruntuhan pasir.dan setelah finish bor tambakan
lagi polimer/bintonik , dan tahan bor sampai cairan terangkat, matikan mesin bor
kalau catting sudah terangkat keatas, cabut pipa dengan cepat untuk menghindari
keruntuhan pasir. Namun keselamatan dan keamanan kru harus tetap diperhatikan.
Each area of the lithology is different, sand, hard soil, sticky soil, gravel, to drill in the
sand area, do a quick drill and mud water must be added and polymer / bintonik is
added to thicken the slush pit water so that all the catting is lifted and can withstand
the walls of the borehole from collapsing sand. and after finishing drill the polymer /
bintonik add more, and hold the drill until the liquid is lifted, turn off the drilling
machine when the catting has lifted upwards, pull out the pipe quickly to avoid sand
collapse. However, the safety and security of the crew must still be considered.
Untuk bor di area koral/kerikil pergunakan polimer/bintonit atau kalau cairan tersebut
tidak bisa mengatasi masalah pergunakan cassing HQ atau NQ tergantung
kesepakatan kontraktor dan klient.
To drill in the coral / gravel area, use polymer / bintonite or if the liquid cannot solve
the problem, use HQ or NQ cassing depending on the agreement of the contractor
and client.
Lakukan Pattrent hole bila tidak memungkinkan memakai cassing HQ atau NQ.
Do Pattrent holes if it is not possible to use HQ or NQ cassings.
THANK YOU
IT WILL BE USEFUL