I. Specific Gravity
1. Metode analisa / Test methode : ASTM D-1298
2. Langkah kerja / Procedure :
- Masukkan sample ke dalam gelas ukur ±250 ml,
- Masukkan kedalamnya Hydrometer dan dibaca skala pada dinding alat
tersebut untuk mendapatkan Specific Gravity pengukuran.
- Suhunya diukur dengan thermometer.
- Dicari angka Specific Gravity pada skala dan suhu 60 °F yang ada pada
Table 23 ASTM-IP Petroleum Measure Table.
Pour the sample into measuring glass, put the hydrometer, read the scale to
get the observe SG. Temperature measurement with thermometer, find the
conversion Specific Gravity at 60 °F at ASTM-IP Petroleum Measurement
Table 23.
Misal / Example : Observe SG = 0.767
Temperature = 81 °F
Specific Gravity = 0.7757 at 60/60 °F
II. API Gravity, in °F
1. Metode analisa / Test methode : ASTM D-28
2. Langkah kerja / Procedure :
Sama dengan Specific Gravity, setelah didapatkan angka Specific Gravity
pada 60/60 °F maka dapat dihitung API gravitynya pada 60 °F.
Same step with the specific grafity, after get the value of specific gravity at
60/60 °F than API gravitynya at 60 °F can be account.
Misal / Example : Specific Gravity = 0,7757 at 60/60 °F
API Gravity =
VI. BS & W, in %
1. Metode analisa / Test methode : ASTM D-96 dan IP-2542
2. Langkah kerja / Procedure :
- Tuang contoh ke dalam centrifuge tube
- Letakkan tube ke dalam mesin centrifuge, putar 15 menit pada 1000 rpm
- Ukur volume padatan yang mengendap bagian bawah
- Air dibagian tengah, minyak dibagian atas, lalu diukur volume totalnya
(kotoran + air + minyak).
- Kemudian hitung persentasenya masing-masing volume.
Pour the sample into the centrifuge tube, put the tube in to the centrifuge
machine, turn on for 15 minute, measuring the sediment volume at the
bottom of tube, the water in middle, the oil at the top and the total volume.
Account the percentage each.
Misalkan / example :
Volume minyak / oil vol = 280 ml
Volume air / water vol = 36.80 ml
3
Water volume ( % KA ) =
= 11.5 %
BS dan W (% BS&W) =
= 12.5 %
A. Ca2+, in ppm
1. Metode / Methode : Titrasi / titration
2. Cara kerja / Procedure :
- 10 ml sampel ditambah 6 tetas larutan buffer ditambah 4 tetes larutan
Indikator Murexide
- Titrasi dengan larutan EDTA sampai berwarna ungu tua
- Volume titrasi menunjukkan kandungan ion Ca2+
Add 6 drops of Buffer solution to 10 ml water sample, add drops murexide
indicator, titrate with EDTA until violet colour. Volume of titration is the oil
Ca2+.
C. Mg2+, in ppm
Metode / Methode : Titrasi / titration
Cara kerja / procedure :
Hasil dari Mg2+ hasil dari (Ca2+ + Mg2+) - Ca2+
Titration result of Ca2+ dan (Ca2+ + Mg2+) - Ca2+
D. Fe3+, in ppm
1. Metode / Methode : Titrasi / titration
E. Cl- , in ppm
1. Metode / Methode : Titrasi / titration
2. Cara kerja / Procedure :
- 2 ml sample ditambah 1 tetes larutan Potassium Chromate
- Kemudian dititrasi dengan larutan AgNO3 sampai terjadi endapan merah
bata.
Add 1 drops of potassium chromate to 2 ml water sample, add 1 ml
potassium thyocyanate, shake to mix, titrate with AgNO 3 solution until red
brown colour sediment show. Volume of titration is the ion Cl-.
G. HCO3- , in ppm
1. Metode / Methode : Titrasi / titration
2. Cara kerja / Procedure :
7
H. SO42-,in ppm
1. Metode / Methode : Titrasi / titration
2. Cara kerja / Procedure :
- 50 ml sample ditambah 1 sendok serbuk BaCl2
- Ditambah 2 ml larutan aqua regian kemudian dibaca pada alat Hellige
Turbidimeter.
Add 1 spon of BaCL2 to 50 ml water sample, add 2 ml aquaregia solution
than read at hellige turbidimeter.
I. SiO2, in ppm
1. Metode / Methode : Titrasi / titration
2. Cara kerja / Procedure :
- 50 ml sample (tanpa campuran) dimasukkan dalam tabung turbidimeter
- kemudian dibaca pada alat Hellige Turbidimeter.
50 ml sample poured in to turbidimetric glass, read with the hellige
turbidimeter.
J. pH, in ppm
1. Metode / Methode : Titrasi / titration
2. Cara kerja / Procedure :
- 10 ml sample ditambahkan 0,5 ml larutan indicator Bromo Thymol Blue
(BTB)
- Lihat pH-nya pada comparator.
Add 0.5 ml Bromo Thymol Blue (BTB) Indicator solution to 10 ml sample,
mix, than read the pH in the comparator.
TDS =
TSS =
O. Turbidity, in NTU
Alat dibutuhkan / equipment needed:
- portable turbidimeter series 2100P,…… Cat No : 46500-00
- sample cell , 1 I inch ……………… Cat No : 24347-06
Reagent yang dibutuhkan / Reagent needed:
- Silicone Oil 15 ml ………………… Cat No : 1269-36
10
P. Specific Gravity
1. Metode / Methode : ASTM D-1298
2. Cara Kerja / Procedure :
- ± 100 ml sample dimasukkan kedalam gelas ukur
- Kemudian kedalamnya dimasukkan Hydrometer dan dibaca skala
pada dinding alat tersebut. Catat suhu pengukuran.
- Hitung Rumus : x = (selisih temp pembacaan – temperatur 60) x 0.0002
- Hitung Rumus : y = x + SG pembacaan hydrometer
Pour the sample into measuring glass, put the hydrometer, read the scale
to get the abserve SG. Temperatur measurement with thermometer.
11
IV. Turbidity
1. Metode / Methode :
2. Cara Kerja / Procedure :
Lihat pada prosedur Uji lab Air Formasi Bagian O
Look at the Formation Water Lab Test Procedure Part O
V. pH
1. Metode / Method :
2. Cara Kerja / Prosedure :
Lihat pada prosedur Uji lab Air Formasi Bagian J
12
VI. Fe3+
1. Metode / Methode :
2. Cara Kerja / Procedure :
Lihat pada prosedur Uji lab Air Formasi Bagian D
Look at the Formation Water Lab Test Procedure Part D
VIII. Phenols
1. Metode / Methode :
2. Cara Kerja / Procedure :
Lihat pada prosedur Uji lab Air Formasi Bagian K
Look at the Formation Water Lab Test Procedure Part K
XII. HCCV
Metode dan cara kerja / Method and Procedure:
Lihat pada Prosedur Uji Lab Air Formasi bagian VII.
Look at the Formation Water Lab Test Procedure Part VII.
XVI. BOD5
Analisa BOD5 dijelaskan secara khusus (lihat daftar isi).
Look at special analyze part for BOD5.
XV. COD
Analisa COD dijelaskan secara khusus (lihat daftar isi).
Look at special analyze part for COD
15
2. Procedure:
a. Pipet 100 ml sample kedalam conical glass, tambah 0.5 ml
Phenolphthalein indicator Solution, lalu titrasi dengan
Hydrochloric Acid Standard. Catat Volume titrasi sebagai “p”
ml
16
17
70 gram KOH + 15 Gram KJ (or 13.5 gr NaI) make the Solution with 100
ml aquadest put in dark and cold room.
18
The 3rd and the 4th bottle, close as soon as possible without trap the
air.
Put the 3rd and the 4th bottle in the incubator water bath @ 20°C, in the
dark room for 5 days.
5. Ukur jumlah oksigen terlarut pada botol kesatu dan 2 dihari ke 1 dan
ke 5, ukur oksigen terlarut pada botol ke 3 dan ke 4 dihari ke 5, jika
oksigen pada botol ke 3 dan ke 4 habis artinya sample terpolasi berat
, agar pengukuran akurat encerkan dengan air suling yang jenuh
dengan udara bebas.
st
Measure the dissolved Oxygen at the 1 and 2nd bottle at the 1 st
day
and at 5 th day, measure the dissolved oksigen,at the 3 rd
and 4th bottle
at the 5th day, if the Oxygen at the 3rd and 4th bottle empty it means the
heavier pollution in the water, the sample measure need re-measure
by solute with the water saturated free air.
BOD 5th days (ml O2/l) = Non Incubation Oxygen (avg.the 1st 2nd bottle
Incubation Oxygen (avg the 3rd and the 4th
bottle).
19
20
Titrate the sample which it’s the volume is the same with the blank
solution, which it’s the volume is the same with the blank solution,
with the FAS until the young red colour reach, record the titration
volume.
b. Peralatan / equipment
1. COD reactor, 240 Cat No : 45600-02
2. Vial + Cap With inert Teflon liner for mixing bottle,
Cat no : ….. Cat
c. Langkah kerja / test procedure
1. Blender 100 ml sample sampai homogen selama
30 detik.
Homogenize 100 ml sample for 30 second in a
blender.
21
C. Definisi
Oksigen Demand adalah jumlah oksigen yang dibutuhkan pada
kondisi test tertentu untuk mengoksidasi zat organic dan inorganic.
26
E. Peralatan
1. Reflux Apparatus
2. Sample Heating Apparatus
3. Blending Appratus (house Blender)
F. Reagents
1. Ferrous Ammonium Sulfate Solution Standart (0.25 N)
98 gram FeSO4 (NH4)2SO4.6H2O dilarutkan dengan air,
tambah 20 ml H2SO4 (SP.GR.1.84), dinginkan dan larutkan
sehingga volume 1 liter. Buat larutan ini sebelum digunakan.
Untuk standarisasi, larutan 25 ml 0.25 N larutan K 2Cr2O7
sehingga 250 ml tambah 20 ml H 2SO4 (SP.GR.1.84)
dinginkan . titrasi dengan FAS yang akan dibuat Standard
NFAS =
27
G. Sampling
Simpan sample pada suhu 4 °C jika baru akan dianalisa 24 jam lagi
Simpan sample pada pH< 2 dan suhu 4 °C Jika akan dianalisa dalam
waktu 2-7 hari lagi. Penambahan 2 ml concentrate H 2SO4 / liter pada
saat isi sample.
H. Prosedur
1. Blending sample sampai homogen, masukan 50 ml sample
ke dalam refluks flask, jika sampel mengandung 800 mg/lt
COD larutan sampel dengan reagent water (K 2Cr2O7) terlebih
dahulu.
2. Isi 50 air kedalam refluks flash untuk penentuan blank.
3. Untuk mengecek apakah angka sudah valid, buat ketentuan
standard dengan langkah 5 (COD 500 mg/liter harus
28
I. Perhitungan
29
Filter 500 ml sample head to boil in the beaker glass, let the sample
reduce until 25 ml volume.
Clean the crust around the side of glass with the rubber spatula at tail.
mix it with the sludge of solution.
30
3. Tuang sample C.1 dalam sample C.2 secara bergantian agar betul-
betul homogen.
Pour C1 to C2 solution alternate each to make sure the perfect
mixing.
31
2. Jika sample dari mesin ambil sample yang cukup mewakili dengan mengambil
sample segera segera mesin dimatikan (pada posisi glycol mengendap).
If the sample from engine, take the representative sample by taking it’s
soon after the engine turn off.
32
33
A. Umum / general
Semen yang umum dipakai pada operasional pemboran di Pertamina EP Region
Sumatera adalah semen kelas G. Mengacu pada standard API Spec 10 section 2.
Semen kelas G dibuat untuk digunakan pada pemboran sumur mulai dari permukaan
sampai kedalam 8000 ft (2440 m) atau dapat digunakan untuk pemboran dengan
temperatur tinggi dan lebih dalam dengan penambahan accelerator dan retarder.
1¼“
2“
8¼“ 20 ½ “
2. Cara / Procedure :
34
The sack must be placed in a suitable position so that the sample tube can be
inserted throught the bites valve diagonally into the center of the sack.
Minimum 1 sample from each 50 sack (or less) shall be obtained.
Berat sample untuk tiap item test sesuai table as table below.
TABLE
WEIGHT OF TEST SAMPLES
QUANTITY OF CEMENT QUANTITY OF CEMENT
ITEM TEST / METHOD OF FOR SINGLE TEST, FOR COMPLETE TEST,
TEST MINIMUM MINIMUM
(KG) (KG)
Soundness (for class A, B, C) 0.5 0.5
Finenness (for class A, B, C) 0.5 0.5
Water Content 1.1 1.1
Slurry Density 1.1 1.1
Compressive Strength 1.1
Atmospheric 1.1 42.5
Pressure 1.1 42.5
Thickening Time 1.1
Casing 1.1 6.8
Squeeze 1.1 6.8
Fluid Loss 1.1 1.1
Permeability 1.1 1.1
Rheological Properties 1.1 1.1
35
37
TABEL
BASIC FOR CASING AND CEMENT SPECIFICATION TEST SCHEDULES
Mud Surface Bottom Hole Bottom Time to
Schedule Depth Density Pressure Circ. Hole Reach
No. (ft) (lb/gal) (psi) Temp.°F Pressure Bottom min.
1 1000 10 500 80 1020 7
2 6000 10 750 113 3870 20
3 8000 10 1000 125 5160 28
4 10000 12 1250 144 7480 36
5 14000 16 1750 206 13390 52
6 16000 17 2000 248 16140 60
38
2. Tuang air + Additive kedalam mixing container, putar pelan dengan 4000 ±
200RP M (66.7 ± 3.3 rev/s) kemudian selama tidak lebih dari 15 detik
tambahkan semua campuran semen.
Pour the water + additive into the mixing container, the mixer turn on the slow
speed 4000 ± 200RP M (66.7 ± 3.3 rev/s), than add all of cemen not more than
15 sec.
Pour immediately the slurry into the atmospheric pressure consistometer, stirred
at 190 °F for 20 minute, remix for 335 sec. at high speed in the blender, than fill
the slurry to 250 ml graduated glass cylinder, sealed to prevent the conversation,
the cylinder must be set on the steel plate whish the water as “free water cotent”
standard 0% by volume.
4. Yield Point
Baca Yield Point pada putaran 300, 200, 100, 6 dan 3 rpm untuk adonan :
- Segera setelah mixing
- Setelah pemanasan 190 °F
Read Yield Point at 300, 100, 6, 3 rpm for :
- Soon after slurry mixing
40
41
- Residu @ 325 #, %
Timbang 100 gr fly ash, ayak dengan 325 mesh selama 30 menit, ambil sisa
ayak dan timbang, nyatakan dalam %.
Shake 100 gr of fly ash with 325 mesh for 30 minute, weight of unpass material
is in % residu.
- Moisture Content, %
Panaskan 100 gr fly ash dalam oven @ 100 °C selama 2 jam, dinginkan lalu
timbang, berat yang hilang sebagai % hasil.
42
- SiO2
Turbidimeter Methode
Buat larutan 1 gr fly ash, tambahkan air sehingga 100 ml, ukur kekeruhan
dengan alat turbidimeter.
Make the solution of 1 gr fly ash, add water to 100 ml, measure the turbidity.
B. Test Mutu Chemical Mengacu Pemakaian Lapangan / Chemical Quality Test Due
to the Field Using.
1. Buat bubur semen SG 1.38 (11.5 ppg) dengan komposisi sebagai berikut :
Mix the cement slurry SG 1.38 (11.5 ppg) with the compotition as below :
43
2. Masukan bubur semen dalam kubus perendaman, rendam pada suhu 171 °F untuk
casing 13.3 / 8“ atau 218 °F untuk casing 9.5/8” selama 24 jam.
Put the cement slurry in to the box, singk at 171 °F for casing, 13.3 / 8 “ trayek or
218 °F for casing 9. 5/8” trayek along 24 hours.
C. Test mutu Chemical Mengacu American Petroleum Institute Spec 10 A Edisi 19,
April 1977. / Quality test of the chemical due to American Petroleum Institute
Spec 10 A, 19th edition, April 1977.
1. Definisi / Definition
Fly Ash adalah sisa hasil pembakaran tanah atau batu bara dan merupakan proses
pembakaran melalui boiler. Fly ash adalah sebuah pozzolan buatan.
Fly ash is the finely divided, residue that result from the combustion of ground or
powdered coal and is transported from the firebox through the boiler by flue gases.
Flay ash is an artifical pozzolan
Pozzolan adalah siliceous atau silicon dan alumanium mengandung sedikit atau
tidak sama sekali semen, dengan adanya zat terbang, reaksi bahkan kimia dengan
kalsium hydroksida pada temperature tertentu mempunyai sifat-sifat cement.
Pozzolan is siliceous or silicon and alumanium material which in itself proseses little
or no comentious value but will, in finely divided from and in the presence of
44
2. Sifat fisika dan kimia yang dikehendaki / Physical and chemical requirements.
Fly ash harus memenuhi sifat fisika dan kimia sesuai table berikut:
Fly ash shall conform to the physical and chemical requirements given in table
below :
TABEL
FLY ASH PHYSICAL AND CHEMICAL REQUIREMENTS
Required Test Source of Test Numerical Value
Physical
Pozzolanie Activity
Index With Lime ASTM C6182 and ASTM 800 psi (5.5 Mpa).min, in
C3112 7 days
Wet Screen Analysis
Passing US Std No. 200* Sieve (75 micrometers-µm) 90% min
Passing US Std No. 325* Sieve (45 micrometers-µm) 85% min
Chemical
Silicon Dioxide (SiO2)
Alumanium Oxide (Al203) ASTM C618 70.0 % min
Iron Oxide (Fe2O3)
Sulfur Trioxide (SO3) ASTM C618 3.0% max
Moisture Content ASTM C618 3.0% max
Loss on Ingnition ASTM C618 6.0% max
Available Alkalis, as ASTM C618 2.5% max
Na2O
45
3. Performance Spesifications.
Fly ash shall conform to the following performance requirement :
a. Compressive Strength
1. Cement Class II / class II cement
Gunakan campuran semen API kelas H : Fly Ash perbandingan 50 :
50 dan 40 persen air dari berat campuran, Compressive Strengh tidak
lebih kecil dari 30 % control semen Kelas H dengan 38 persen air
setelah 24 jam perendaman pada API Schedule 1S (95o F, 800 psi ;
35 oC , 5500 Kpa)
Using 50:50 blend of Fly Ash / API Class H cement and 40 % water
by weight of blend, the compressive strength shall not be less than 30
% of the control Class H cement with 38 % water after 24 hour curing
under API Table DI schedule I S (95 oF,800 psi; 35 °C, 5500 kpa)
46
b. Thickening Time
1. Cement Class H / Class H cement
Gunakan campuran semen API kelas H : fly Ash perbandingan 50 :
50 dan (lihat catatan) 40 persen air dari berat campuran, thickening
Time antara 1,25 dan 2,5 kontrol semen kelas H dengan 38 % air jika
di test pada API schedule 5 S
Using 50 :50 blend of Fly Ash/ API Class H Cement (see NOTE) and
40 % water by weight of blend, the thinckening time shall be between
1.25 and 2.5 times the control semen kelas G dengan 44 % air jika di
test pada API schedule 5 S.
Catatan / Note :
Ketika digunakan dengan semen portland, fly ash yang dibutuhkan
secara absolute merupakan volume semen yang digantikan, bisa
dihitung dari formula dibawah ini:
47
= X
48
Diabsorpsi dari “Guide to Blowout Prevention “ oleh Well School dan Shell Methode
Series” 1963
Adopted from “Guide to Blowout prevention “by Well Control School dan Shell
Methode Series”1963
Pour the sample into mud balace cup full, close, clean sample covered
the cup, rince the vover with water, put the balace in place, measure the
specific gravity of mud.
2. pH
Metode analisa dan langkah kerja lihat procedur uji lab analisa Air Formasi
Bagian K
49
Pour mud sample into the filter press cup, give the 100 psi pressure
supplied by gas CO2 or N2 for 30 minute, if the time 30 minute have
rich, release the pressure, read the water volume as the water loss in
cc. if the filtrate obtained for 7 ½ minute is greater than 8 ml, the value
be double to give a fair approximation.
50
Pour 10 ml of mud sample into the retort kit cup, heat the mud
sample distill, continue until no more fluide distill. The difference
volume of mud and distilled fluid ia solid content, account in %.
b. Oil Content , in %
Baca tinggi minyak pada tampungan tetesan sebagai Oil
Content dinyatakan dalam persen.
Read the volume of oil distill as Oil Content account in %.
5. Sand Content, in %
Alat / tool : Funnel set
Langkah Kerja / procedure :
Contoh sebanyak 25 ml dimasukkan kedalam funnel set dengan
saringan 840 micron, cuci sisa saring dengan air bersih baik funnel
screen, siram dengan aquadest 100 ml, tampung air pasir disaringan
51
Pour 25 ml of mud sample into the funnel set complete with filter 840
microne, wash to clean the sand trapped at filter, invert the filter, pour it
with 100 ml of aquadest into the centrifuge tube. Account the sand
volume X 4 as % of Sand Content.
6. Rheological
Difinisi / definition
Rheology adalah pelajaran mengenai aliran cairan dan gas. Viscositas
adalah ketebalan relative untuk dapat mengalir. Dalam industri
perminyakan istilah rheologi dimasukkan untuk viscositas.
Rheology is the study of the flow liquids and gases. Viscosity which can
be thought of as the resistance to flow or relative hickness of a fluid, is
cammon rheological term used in the oilfield industry.
Cover the tip with finger, pour the marsh funnel cone
with the mud sample to the bottom of screen, remove
the finger from outlet , carefully observe the time in
52
The reading after the kit stoped for 10 second and after
10 minute at the low speed (300 rpm) reading and after
53
8. Cement Indication, + or –
Alat / Tool : Pipette
Langkah Kerja / Procedure :
54
9. Fe Content , in ppm
Metode analisa dan langkah kerja lihat prosedur uji lab analisa air formasi
bagian D.
Test methode and [rocedure read the lab test prosedure for formation water part
D.
Test methode and prosedure read the lab test prosedure for formation water
part B.
Test methode and procedure read the alkaline lab test prosedure.
55
Test methode and procedure read the PHPA concentration test introduction
sheet.
Coustic - - - - -
Soda
Supersen / - - -
YP70
CMC - - - -
56
Umumnya analisa serbuk bor dilakukan dengan menetesi chemical pada sample.
Usually to analize the cutting by drop chemical on the cutting.
57
58
1. Cari pour point crude TPS-01 tanpa injeksi chemical (dlm °C).
Fine the pour poin of TPS-01 crude before chemical injection. ( °C)
2. Panaskan Crude dalam water bath pada suhu ((1) + 8 °C) tanpa diaduk.
Heat crude in the water bath at temp ((1) + 8 °C) without stirring
4. Tuang crude oil ke dalam pour point tube/jar, tutup dengan sumbat ber
thermometer, posisikan thermometer terendam ditengah ketinggian tube.
tempatkan tube/jar dalam cooling bath.
59
5. Secara periodic amati apakah crude masih bisa dituang dengan cara
memiringkan tube/jard Catat suhu pada saat crude membeku sebagai pour
point.
Periodically observe for liquid flow by filting the jar, record the temperature
whenever there is crystallization of crude as the pour point.
6. Kesimpulan untuk Pour Point Depressant test adalah penurunan pour point.
The pour poind depressant summary is the decreasing pour point.
60
2. Panaskan crude dalam water bath pada suhu ((1) + 8 °C) tanpa diaduk.
Heat crude in the water bath at temperature ((1) + 8 °C) without stirring.
61
6. Panaskan Crude dalam water bath pada suhu ((1)+8 °C) tanpa diaduk.
Heat crude in the water bath at themperature ((1)+8 °C) without stirring.
62
1. Isikan air formasi ke dalam gelas beker 500 ml, sebanyak 400 cc
Pour 400 cc formation water into beaker glass 500 cc capacity.
2. Kemudian air tesebut diberi chemical dengan dosis 5 ppm, 15 ppm, 25 ppm.
Chemical injection each glass with 5 ppm, 15 ppm, 25 ppm, dosis and blank.
3. Panaskan air yang telah diberikan chemical sampai temperatur kepala sumur.
Heat the sample to the well head temperature
4. Dan setelah dipanasi lalu kita dinginkan kembali untuk pengukuran scale
index (SI).
Let the sample cool until room temperature reach, analyze the scale index
(SI).
63
3. Khusus untuk analisa flash point jika penyimpangan lebih besar dari
spesifikasi pabrik maka besar penyimpangan tidak dibatasi.
64
3. Ambil sample langkah satu (1), dari dosis 5, 10, 15 dan 20 ppm.
Take the step 1 sample give chemical injection with the dosis 5, 10, 15 and
20 ppm.
5. Pengamatan BS&W tiap 1 jam. diperoleh data BS&W per jam tiap group
sample.
BS&W abservation every 1 hour / each hour BS&W data of each group will
be got
9. Crude langkah 8 dikocok 50 s.d 100 kali dianalisa salt contentnya. diperoleh
satu data salt content.
Shake the step 8 crude for 50-100 times analyze the salt content / got one
salt content data.
67
6. Panaskan gelas beker berisi larutan + coupon dalam water bath dengan
suhu-suhu flow line dilapangan selama 7 hari.
Heat the beker glass that filled with the solution + coupon in the water
bath for 7 days at ± field flow line temperature.
7. Bersihkan coupon menurut step (C) atau (D) hitung rate korosinya.
Clean the coupon through step (C) or (D), count the corrosion rate.
1. Catat nomor seri coupon, jika untuk penelitian khusus buat photo sebelum dan
sesudah dicuci.
68
3. Perhatikan dengan teliti kondisi kupon, siapa tahu ada scale atau material lain yang
terbentuk.
Visually examine coupon, qualitative analysis of adherent scale of foreign material
maybe performed.
4. Celup kupon dalam larutan hydrocarbon seperti xylene atau toluene untuk
melepaskan minyak, oil wet material atau paraffin jika ada.
Immerse the coupon in a suitable hydrocarbon solvent, such as clean xylene or
toluene to remove the oil, oil wet material or paraffins.
7. Jika kupon ditempeli scale dan hasil pengkaratan celup kupon dalam 15% HCl
untuk melepaskannya.
Jika kupon tidak ditempeli scale dan hasil pengkaratan celup kupon maka cukup
dibersihkan dengan udara kering bertekanan.
If coupon coated by scale or corrosion proses, immerse the steel coupon in 15%
HCl to remove its.
If coupon are not coated with scale or corrosion proses, cleaned by blasting with
glass beads.
12. Seka segera dengan IPA atau acetone lalu keringkan dalam oven.
Rinse the coupon immediately in IPA or aceton and dry oven.
1. Catat Nomor Seri Coupon, jika unutk penelitian khusus buat photo sebelum dan
sesudah dicuci.
Record the coupon serial number, make the photograph before and after
cleaning for special analyze.
2. Perhatikan dengan teliti konidsi coupon, siapa tahu ada scale atau material lain
yang terbentuk.
Visually examine coupon, qualitative analysis of adherent scale or foreign
material may be performed.
70
Rate corrosion = mass loss x 365 x 1000 / (initial area x days x density)
71
72
3. Tambahkan 1 tetes diphenyl carbon azon, aduk sampai warna kuning, titrasi
dengan AgNO3 (0,282 N) sampai berwarna merah jambu.
Add 1 drops diphenyl carbon azon, shake until yellow colour, titrate with 0,282
N AgNO3 to get young red colour.
% HCl – (ml AgNO3 x Chloride factor) / (density sample x 1000)
Chloride factor = 10 mg ? HCl ion / ml AgNO3.
CARA PENGGUNAAN ALAT ATMOSPHERIC CONSISTOMETER
USING THE ATMOSPHERIC CONSISTOMETER
1. Penuhi water alat dengan air. / Fill the water bath with water.
2. Alirkan listrik 220 volt ke alat / Fit the alectisc 220 volt to the kit.
3. Masukkan bubur semen yang akan dianalisa ke tabung yang sudah disediakan
(banyak contoh ±750 ml)
4. Masukkan tabung yang sudah disiapkan ke dalam bath.
Put the sample cup into the bath.
5. Hidupkan power, heater, master, motor
Turn on the power, heater, master, motor.
6. Catat temperature awal (˚C). / Record the initial temperature.
7. Naikkan tekanan dan temperature tiap 10 menit sampai tekanan pengetesan
maksimum yang dikehendaki.
73
No. Seri -
No. Moveable -
Model -
Voltase 220 Volt
consistency reach the number of 10 than the cement slurry already hard, record
when the 10 number can be reach.
9. Off kan semua tombol yang ada. /Turn off all the switch.
10. Putuskan aliran listrik ke alat konsisto meter, ambil tabung yang berisi contoh
bubur semen. Pekerjaan dengan alat selesai.
Off the electris power, take the sample cup. The work finish.
Kegunaan / Purpose :
74
6. Hidupkan alat
Turn on the kit
75
8. Tekan tombol GO
Press the GO key
9. Saat pertama kali crystal mulai terbentuk (FCTA) tekan PRT untuk mencetak
temperature
When the first crystals to Appear (FCTA) press PRT key to record the temperature.
10. Saat temperature maksimum (TCT) dicapai, tekan PRT, dapat ditekan beberapa kali
saat hamper tiba maksimum agar tidak kehilangan data temperature maksimum.
When the the maximum temperature reach, press PRT, the PRT key can be press
coulpe times to capture and record the maximum temperature.
11. Saat temperature mulai turun, setelah beberapa derajat, setel cold plate temperature
ke 0%, lalu tekan FEED. Teruskan monitor saat kristal mulai larut, pada saat kristal
larut tekan PRT, angkanya sebagai LCTD.
When the the temperature going down, after coulpe degree, set the cold plate
temperature control back to 0%, than press FEED key. Observe the crystallized
sample as it is warmed and the crystal begin to dissolved, when the last crystal
dissolved, press PRT, the value of temperature is the LCTD.
76
77
3. Hidupkan alat
Turn on the kit
6. Buka tutup alat, keluarkan sample, banyaknya sediment dan air dapat dibaca.
Turn off the kit, the sedimen and water cab be read.
No. Seri -
No. Moveable -
Model Commercial Bleder 34,Bl 97
Voltase 110 Volt
1. Isi tempat sample di bagi atas alat dengan sample, tutup tempat sample.
Fill the sample cup at the top kit with sample, that close the sample cup
78
3. Hidupkan Alat
Turn on the kit
Umum/ General
Konsentrasi Partially hydrayzed polyacrylamide (PHPA) dalam “Lumpur pemboran type
water base” dapat dilakukan dengan metode distilasi dan titrasi. Pada saat hydrolysis
79
Keselamatan / Safety:
Chemicals dalam peralatan ini bisa beresiko jika bersentuhan langsung dengan tubuh,
tertutup (napas, meletus, terbakar).
The chemicals using with the kit is risky if touch to body, breath, explore and fire.
Untuk mengoperasikan “hot plate” yakinlah terlebih dahulu bahwa alat-alat listrik berfungsi
dengan baik dan digrounding plug (dihubungkan ke tanah/lantai)
The operate the hot plate, the first thing to do is to ensure all the electrical are function
anda grounding plug.
Baca dan ikuti perintah-perintah pengoperasian pada hot plate. Jangan ditinggalkan saat
dipanaskan. Gunakan sarung tangan saat menggunakan barang yang panas.
Read and follow the hot plate intruction. Don’t leave the kit whenever heated. Use glove
whenever work the hot thing.
81
TABLE
DATA TO MAKE THE STANDARD PHPA CURVE
Sample Ml of titration
Sample + No EZ Mud DP
Sample + 0,5 gr EZ Mud DP
Sample + 1 gr EZ Mud DP
Sample + 1-1/2 gr EZ Mud DP
Sample + 2 gr EZ Mud DP
1. Isi bath dengan air, (Jangan diisi selain dari pada air)
Fill the bath with water (Do not fill the bath with another fluid)
3. Hidupkan alat.
82
No. Seri
No. Moveable
Model
Merk
1. Hubungan peralatan snowpack ke tabung gas CO2 dengan turunan tubing/pipa. Ikat
dan k u a t k a n hubungan koneksi,
Install the connection tube, connect the snowpack to the CO 2 gas cylinder. Tight the
collection
2. Alirkan gas CO2 ke snowpack secara perlahan selama ± 2 1/2 menit untuk
menghasilkan es kering sebanyak 500 gr.
83
3. Tutup aliran dari tabling gas CO2 pastikan tidak ada kebocoran.
Turn the valve to close the CO2 gas flow, make sure there is no leak.
4. Lepaskan hubungan snowpack yang telah berisi es kering dengan tabung gas CO2,
es kering dapat dikeluarkan dari snowpack.
Release the connection between the CO 2 gas cylinder and. the snowpack, dry ice
can be pour to use.
Keselamatan / Safety :
1. Selama pembuatan es berlangsung jangan sekali-sekali koneksi dipegang dengan
tangan terbuka (tanpa alas).
Do not touch the lube and connection along the dry ice processing.
3. Utamakan keselamatah.
Safety first.
84
2. Hidupkan alat.
Turn on the kit.
85
4. Putar roda pengatur bacaan sampai angka no! dan jarum merah menunjukkan pada
garis nol.
Turn the wheel until zero and the red stick to zero position.
5. Buka t ut up alat, keluarkan sample, banyaknya sedimen dan air dapat dibaca
Turn off the kit, the sedimen and water can be read.
6. Bila penunjukkan b e l u m tepat atur dengan tombol yang berada di atas alat.
If not fit yet arrange by turn the button at the top of the kit.
86
2. Isi tabung milipore dengan sample akan dianalisa 31/2 liter. Tutup rapat tabung
millipore.
Fill the millipore container with 3 1/2 liter of sample. Close the millipore container.
87
6. Bila tekanan telah tercapai, buka kerangan yang ada dibagian bawah, bersamaan
dengan menghidupkan stop watch.
If the pressure reached, open the water tap at the same time as the timer start.
7. Setiap diperoleh 100 ml cairan pada tabung penampung, catat waktu yang dicapai.
Every 100 ml of fluid fall into the receiver, record the time.
9. Biia waktu a l i r mencapai ± 900 detik, sebaiknya pengetesan di stop, karena sudah
rnelewati standart.
If the flow time reach 900 second than the prosess must be stop due to pass the test
standard.
10. Stop the proses, buka bagian bawah peralatan dan seka dengan tetra (CCl4), keringkan
lalu timbang.
Stop the process, open the lap below the container, take out the filter. Dry it than
weight. Rinse with the tetra ( CCl4), dry it than weight.
2. Hidupkan alat.
Turn on the kit.
89
No. Seri -
No. Moveable 9000825
Model Nl Baroid USA
Voltase 110 volt
1. Isi tempat sample dengan10 ml sample, tutup tempat sample. Siapkan gelas ukur 10 ml
untuk ekstrak cairan.
Fill the sample cup with 10 ml of the sample, that chose the sample cup. Prepare the
measuring glass 10 ml for extract the distilled fluid.
90
3. Hidupkan alat
Turn on the kit.
4. Tunggu sampai tidak ada lagi cairan yang menetes (sampai dengan lampu merah
mati).
Wait until there is no distilled fluid drop, the red Lamp will off.
1. Isi tempat sample sampai sesuai batas (ukuran) yang telah ditentukan pada alat.
Fill the sample cup with the sample to the remark at the kit. that close the sample cup.
91
3. Hidupkan alat.
Turn on the kit.
2. Hidupkan alat.
Turn on the kit.
92
93
2. Hidupkan alat.
Turn on the kit.
3. Isi tempat sample di bagian atas alat dengan sample, tutup tempat sample.
Fill t h e sample cup at the top of kit with the sample, that close, the sample cup.
94
5. Tank plat pada t u t u p tempat sample kearah kanan u n t u k mengetahui apakah api
sudah bisa menyambar, ulangi beberapa saat kemudian jika belum.
Pull the plat at cover of sample cup to the right to check if the fire flash, try for another
moment if fire not flash yet.
6. Catat temperatur pada waktu pertama kali api menyambar sebagai flash point.
Record the temper ature whenever the first fire flash as the flash point.
7. Lakukan pendinginan.
Of the kit to cool.
8. Pekerjaan dengan alat selesai, alat bisa dimatikan.
The work finish, turn off the kit.
CARA PENGGUNAAN ALAT PENGADUK DAN PEMANAS
THE USE OF THE STIR & HEART KIT
95
1. Isi bak alat dengan air sampai sesuai batas (ukuran) yang telah ditentukan pada alat.
Fill the bath with water to the remark at the kit.
96
5. Masukkan ublohde berisi contoh crude yang dianalisa, lakukan bacaan sesuai langkah
kerja analisa minyak pada bab-bab sebelumnya.
Insert the ublohde that filled with the sample, do the step according to the crude oil
analyze at the initial chapter.
97
4. Off kan semua tombol yang ada, putuskan aliran listrik ke alat. Pekerjaan
Turn off all the switch, off the electric power.
1. Isi bath dengan air. (Jangan diisi selain dari pada air, namun sedikit solar untuk
mengurangi penguapan tidak masalah)
Fill the bath wish water. (Do not fill the bath with another fluid, but small amount of
solar if no problem)
98
3. Hidupkan alat.
Turn on the kit.
99
LAMPIRAN XII
PERHITUNGAN DALAM TITRASI DAN KOLORIMETRI
THE ACCOUNTMENT IN TITRATION AND COLOURIMETRIC
A. Titrasi/ Titration
- Q =
- W=
S = ml, result o f t i t r a t i o n
N = normalitet of solution
A = ml, of water sample to be analyze
Q = meq/lt, result in proporsional value
m = mol. Eq dari aunsur/ion diperiksa (BM/ Valensi)
W = mg/lt or ppm. Result in proporsional value
100
Re = reading on curve
Dx = Time of thinner
LAMPIRAN XIII
PEMBUATAN LARUTAN UNTUK TITRASI
MEAKING THE SOLUTION FOR TITRATION
A. INDICATOR / INDICATOR
- ORTHO TOLIDINE I %
1 gr orthotolidine dihaluskan, dicampur 100 ml HCl. murni + air suling sampai 1 liter,
vvarnanya akan kelihatan keunguan.
/ gr orthotolidine make it to powder form, mix with 100 ml of concent HCl + aquadest to 1
liter, the colour will be violet
- PHENOLPTHALEIN 0.5 %
0.5 gr phenolpthalein, dicampur 50 ml ethyl alcohol + air suling sampai 100 ml.
0.5 gr phenolpthalein, mix with 50 ml of ethyl alcohol + aquadest to 100 ml.
101
- ERIOCHROME BLACK T 1 %
1 gr erichrome black T + air suling 29 ml + 1 ml 0.5N Na 2CO2 yaitu (2.65gr Na2CO3 +
isopropyl alcohol sampai 100 ml).
/ gr erichrome black T + aquadest 29 m + 1 ml 0.5/V Na 2CO3 is (2.65 gr Na2CO3 +
isopropyl alcohol to 100 ml)
- MUREXIDE 1 %
1 gr murexide + air suling 29 ml + 1 ml 0.5N Na2CO3 + isopropyl alcohol sampai 100 ml
/ gr murexide + aquadest 29 in + 1 ml 0.5N + isopropyl alcohol to 100 ml
- POTASSIUM CHROMATE 3%
3 gr potassium chromate +air suling sampai 100 ml.
3 gr potassium chromate + aquadest to 100 ml.
B. LARUTAN/SOLUTION
- BUFFER SOLUTION, 10.6
54 gr Ammonium chloride + 350 ml Ammonia 25% + 2gr Mg komplex + Air suling
sampai 1 liter
54 gr Ammonium chloride + 350 ml Ammonia 25% + 2gr Mg complex + aquadest to 1
liter
- AQUAREGIA
1 bagian asani nitric + 3 bagian asam hydrochloric
1 part nitric acid + 3 part hydrochloric acid
- BROMOTHYMOL BLUE
102
Make the Oil Lindi Solution due to Scrensen, into a glass of empty pirex, cover
inside with the paraffin, the glass filled with 100 gr water, than add 100 gr NaOH
little by little, mix with the glass stick (not all of natrium hidroxida can be dilute)
after 2 - 3 days the slugged will be sink and clean water at the upside, the clean
solution is assume as NaOH 0.1 N
(b) Untuk membuat larutan NaOH 0,1N maka ambil 8 gr dari larutan (a) lalu
dilarutkan dengan air suling yang telah dimasak (jika tidak dimasak maka air
suling banyak mengandung karbondioksida) sehingga volumenya 1 liter. Larutan
terjadi adalah NaOH 0,1 N.
To make the NaOH Solution 0,1 N, take 8 gr of (a) solution, dilute with cool boiled
aquadest (if not cooked the aquadest will have carbondiokside) so the volume be 1
liter. The solution is NaOH 0,1 N.
103
1. ALKALINITY/ OH- , CO3 ,HCO3 (range 10.00 s.d 4000 mg/ltr as CaCO3)
(PHENOLPHTHALEIN METHOD AND TOTAL METHOD), CARTRIDGE
Sesuaikan volume sample dengan range Alkalinity sample pada Tabel. Masukkan
kedalam Erlenmeyer. tambahkan Reagent Phenolphthalein Indicator Powder Pillow
1 buah, aduk rata.
1. Bila Lar. Sample berubah menjadi warna pink titrasi dengan Sulfuric Acid
(H2SO4) Cartridge sampai warna Lar. Sample menjadi tidak ada (colorless).
Catat end point titrasi :
P alk (mg/ltr) = hasil bacaan pada alat x factor pengali pada tabel
2. Bila larutan tidak berubah (warna tetap setelah ditambahkan bubuk indicator)
artinya P alk = 0 mg/ltr. Lanjutkan dengan penambahan Reagent Bromcresol
Green-Methyl Red Indicator Powder Pillow 1 buah, aduk rata. Titrasi dengan
Sulfuric acid Cartridge sampai warna menjadi biru-hijau - abu-abu (pH 5.1),
violet terang – abu-abu (pH 4.8) , atau pink cerah (pH 4.5). Catat end point
titrasi :
T alk / M alk = hasil bacaan pada alat x factor pengali pada tabel
104
Sesuaikan volume sample dengan range Chloride sample pada Tabel. Masukkan
kedalam Erlenmeyer. tambahkan Reagent Diphenylcarbazone Powder Pillow 1
buah, aduk rata. Titrasi dengan Mercuric Nitrate Cartridge. Warna akan berubah
dari kuning menjadi pink cerah. Catat end point titrasi :
Cl- (mg/ltr) = hasil bacaan pada alat x factor pengali pada tabel
Untuk menghitung NaCl (mg/ltr) = Nilai Cl- x Faktor Pengali 1.65
13. PHOSPHONATE / PO43- (range 0.02 s.d 2.50 mg/ltr and 1.0 to 125.0 mg/ltr)
(PERSULFATE UV OXIDATION METHOD), NO.PROG. 501 PHOSPHONATES
Isi Lar.Blank sebanyak 10 ml air sample, Isi Lar.Sample sebanyak 25 ml air
sample dan tambahkan ke Lar. Sample Reagent I yaitu Pottasium Persulfate Pillow
1 buah, aduk rata. Masukkan lampu ultraviolet (UV) dan proses timer selama 10
menit. Matikan adapter dan angkat lampu UV, keluarkan.
Tuang sample sebanyak 10 ml ke dalam botol yang lain/kurangi dari volume
sehingga menjadi 10 ml pada botoll yang sama, tambahkan Reagent 2 yaitu
PhosVer 3 Phosphate Powder Pillow 1 buah, aduk rata dan proses timer selama 2
menit. masukkan terlebih dahulu blank, kemudian sample, baca .
17. CHEMICAL OXYGEN DEMAND / COD- (range 3 s.d 150, 20 s.d 1500, 200 s.d
15000 mg/ltr)
(REACTOR DIGESTION METHOD), NO.PROG. 435 COD HR
Penyiapan Sample :
Hidupkan COD reactor. Tekan tombol pemanas sampai 150°C. Siapkan 2 tabung
untuk blanko dan Sample. Isi kedua tabung dengan Ragent yaitu COD Digestion
Reagent (sesuaikan ukuran tabung dengan range yang diinginkan). Miringkan
tabung menjadi 45°, isi air sample kedalam tabung sample sebanyak 2 ml (untuk
range pengukuran 3 s.d 1500 mg/ltr). Untuk tabung blank diisi dengan air aquadest
sebanyak 2 ml. Aduk rata.
Masukkan kedua tabung ke dalam COD reactor setelah tercapai temp. 150 °C, set
timer selama 2 jam dan sisipkan temperatur control (alat khusus). Matikan COD
reactor, tunggu sekitar 20 menit sampai tabung menjadi dingin atau suhu ± 120 °C.
Angkat kedua tabung, bolak balik tabung dan taruh di rak lain sampai mencapai
temperatur suhu ruang.
Prosedur Analisa :
Taruh adapter-16 mm kedalam Alat Spektrofotometer, masukkan terlebih dahulu
blank, kemudian sample, baca .
107
Sesuaikan volume sample dengan range Acidity sample pada Tabel. Masukkan ke
dalam Erlenmeyer. tambahkan Reagent Bromphenol Blue Indicator Powder Pillow
1 buah, aduk rata. Titrasi dengan Sodium Hydroxide (NaOH) Cartridge. Warna
akan berubah dari kuning menjadi biru-violet (pH 3.7). Catat end point titrasi
sebagai berikut :
Methyl Orange (mg/ltr) = hasil bacaan pada alat x factor pengali
pada table
108
109
Scope : Metode ini untuk mengetahui adanya chlor bebas didalam air. Dapat
Membasmi bakteri dan mikro organisme lainnya.
110
I. RUANG LINGKUP
Standar ini meliputi definisi, syarat mutu, cara pengambilan contoh, cara uji, cara
pengemasan dan syarat penandaan untuk kaporit.
II. DEFINISI
Kaporit atau Kalsium Hipoklorit adalah suatu bahan kimia dengan rumus kimia Ca(OCl) 2.
4 H2O berupa serbuk putih dengan bau klor yang mengandung available chlorine.
V. CARA UJI
Penetapan Klor Aktif ( Available Chlorine)
Dalam suatu botol timbang, ditimbangkan dengan teliti lebih kurang 2 gram kaporit,
Serbuk kaporit ditaruh dalam lumpang porselin. Botol ditimbang dan isi ditimbang
kembali.
Perbedaan berat merupakan serbuk kaporit yang diuji. Serbuk dituangi air sedikit dan
digilas dengan anak lumpang sampai rata, diencerkan dengan air dan dibiarkan
sebentar.
111
Available chlorine =
112
ASTM D 56 – 77
Precision :
ASTM D 93 – 77
Precision :
113
E. pH
pH of Aqueous Solutions With The Glass Electrode
ASTM E 70 – 74
Precision :
Not more than 0.04
The standart deviation of results (each the average of duplicate determinations)
obtained by analysts in defferent laboratories has been estimated to be 0.04 . pH
unit at 12 degrees of freedom, two such averages should be considered suspect
(95% confidence level) if they differ by more then 0.12 pH unit.
Hasil penyimpangan standar (masing-masing rata-rata dari pengukuran ulang)
didapatkan oleh analis pada laboratorium yang berbeda diperkirakan tidak lebih
dari 0.04. Ukuran pH pada 12 ° keadaan bebas. Rata-rata kedua hasil
pengukuran akan dipertimbangkan (pada 95% tingkat kepercayaan) bila mereka
berbeda lebih dari 0.12
G. Boilling Point
Distillation of Petroleum Products
ASTM D 86 – 77
Precision :
Not more than 5 %
G. Viskositas
Calculating Viscosity Index From Kinematic Viscosity at 40 and 100 °C
ASTM D 2270 – 77
Precision :
Not more than 6.6 %
114
LANGKAH I
1. Mengeset Gas Carrier dengan tekanan masing-masing sebagai berikut :
Syntetic Air 5 psi (tekanan di Pressure Gauge)
Helium 5 psi (tekanan di Pressure Gauge)
Hydrogen 3 psi (tekanan di Pressure Gauge)
2. Menghidupkan peralatan UPS
3. Menghidupkan peralatan Komputer
4. Menghidupan peralatan Gas Chromatograph
LANGKAH II
5. Mengoperasikan Gas Chromatograph
Klik 2x INSTRUMENT 1 (ONLINE)
Klik 1x View
Pilih dan Klik 1x METHOD AND RUN CONTROL
Klik 1x Method
Pilih dan Klik 1x CONDIT M untuk Conditioning selama ±30 menit.
Klik 1x Method
Pilih dan Klik 1x NGA 2261 M untuk methode pengoperasian GC
Tunggu selama 30 Menit atau menunjukkan status READY FOR RUN.
LANGKAH III
6. Memasukkan sample
Setelah pada layar menunjukkan status READY
Hubungkan tabung gas ke peralatan GC
Sebelum memasukkan gas sample Klik PREP RUN
Setelah itu pelan-pelan gas sample di buka
Lalu tekan START pada alat GC
Alirkan gas sampai 1 menit
Tutup kembali gas sample
7. Tunggu sampai laporan tercetak di printer
8. Apabila sample gasnya lebih dari 1 atau banyak kita bisa langsung ke Langkah III
LANGKAH IV
9. Pendinginan Gas Chromatograph
Pilih dan Klik 1x OFF M
Alat GC akan otomatis melakukan pendinginan
Tunggu ± 30 menit atau sampai temperature BACK DET < 100°
Tekan BACK DET untuk melihat tampilan temperature
Setelah temp < 100° REF FLOW dan Mkup (He), Tekan OFF sampai menunjukkan
nol.
115
116