Pengujian Safe Light Dengan Menggunakan Metode Koin
Prosedur/ cara pengujian
1) Pastikan kamar gelap dalam keadaan gelap tanpa penerangan, masukkan film ke dalam kaset 2) Separuh bagian kaset ditutup dengan timbal, kemudian kaset diekspose dengan sinar-X sehingga menghasilkan densitas 0,8 3) Kaset di buka dan film diletakkan di bawah lampu pengaman yang diuji 4) Tempatkan beberaapa koin diatas permukaaan film dan gunakan sebuah karton untuk menutupi semua koin 5) Bila lamanya waktu penanganan film + 45 detik, maka pilih interval waktu yang lebih lama, misalkan 60 detik, maka film dapat dibagi menjadi 6 bagian 6) Jika 6 maka dibutuhkan koin sebanyak 12 buah 7) Letakkan film diatas tempat kerja, tepat di bawah lampu pengaman dan karton ditarik sehingga koin pertama mendapat penyinaran selama 10 detik 8) Kemudian karton ditarik lagi ke bawah hingga koin kedua mendapat penyinaran 10 detik dan demikian seterusnya hingga koin terakhir 9) Bila koin terakhir telah mendapat penyinaran, kemudian lampu pengaman dimatikan dan film diproses dengan waktu standar, sehingga lamanya film mendapat penyinaran lampu pengaman adalah sebagai berikut : Tahap I : (10+10+10+10+10+10= 60 detik) Tahap II : (10+10+10+10+10= 50 detik) Tahap III : (10+10+10+10= 40 detik) Tahap IV : (10+10+10= 30 detik) Tahap V : (10+10= 20 detik) Tahap VI : (10 detik) Setelah itu seluruh permukaan film ditutup dengan kertas dan lampu pengaman dimatikan Kemudian film diproses di kamar gelap
2 Penerangan Khusus / Special Illumination :
a. Safe light : Sebagai pengontrol processing film - Tipe langsung : Cahaya saft light langsung mengenai area bekerja. - Ditempatkan min 1,2 m dari permukaan tempat bekerja. - Tipe tidak langsung : Merupakan penerangan umum. Safe light diarahkan ke eternity sehingga yang digunakan adalah cahaya refleksi. - Ditempatkan 2,1 m dari lantai. - Warna safe light Hijau, merah, coklat : untuk film monocromatik . X-Ray film Merah : untuk jenis orthokromatik . X-Ray dan flomografi b. Vising box : untuk mengecek hasil film processing
Herman Kurnianto http://cafe-radiologi.blogspot.com/2010/10/processing-room-
kamar-gelap.html The occlusal plane is the plane that passes through the opposing biting surfaces of the teeth. The terms upper occlusal plane and lower occlusal plane are used in radiographic positioning when carrying out intra-oral radiography. It is necessary to adjust the position of the patients head before intra-oral radiography to ensure that the appropriate occlusal plane is horizontal and the median plane is vertical. Common radiographic centring points are used to achieve these aims with the patient seated and the head supported adequately. With the mouth open, the upper occlusal plane lies 4cm below and parallel to a line joining the tragus of the ear to the ala of the nose. The lower occlusal plane lies 2cm below and parallel to a line joining the tragus of the ear to the angle of the mouth with the mouth open.
In order to minimize distortion effects and to achieve optimal image geometry,
the following principles have been advocated for intra-oral radiography: The focal spot should be as small as possible. The focal spot-to-object distance should be as great as possible. The object-to-film distance (OFD) should be as small as possible. The film should be parallel to the plane of the object. The central ray should be perpendicular to both the object and the film. Both bitewing and periapical radiography benefit from an accurate and stable position of the image receptor. Bitewing radiography requires that the beam, in the horizontal plane, meets the teeth and the film at right-angles and passes through all the contact areas. For periapical radiography, the ideal principles for optimal image geometry cannot be satisfied in all patients, due to a variety of factors. To overcome these problems, two techniques have been developed: