ELECTRIC SYSTEM
CLA
Presented by:
Ejen Jaenudin, ST
Daftar isi
Layanan Literature
Layanan Literatur diterbitkan oleh MAN untuk membantu ketika bekerja pada sistem
kelisktrikan kenderaan MAN.
System / Electric wiring diagram Abbreviation code Order No.
Equipment List – keys, code numbers, line numbers, symbols T60 81.99598-4962
Catatan:
Layanan literature sebelumnya dengan code letter "T" berisikan circuit diagrams dan descriptions of systems.
Setelah di modifikasi layanan literature dengan code letter "T" berupa system description dan code letter "K" berisikan
circuit diagrams
6 Body
11 Service products
1
2
3 4
5
6 7 8
1. Index
2. Tanggal pengembangan
3. Informasi pengguna, contoh: CLA
4. Nama dari circuit diagram
5. Nomor Circuit diagram, contoh: 64.99192-0202 untuk CLA
6. Nomor circuit diagram sebelumnya
7. Halaman Circuit diagram
8. Total halaman circuit diagram
Socket Relay
V100 (Dioda)
Cable harnes
A
Training & Development
PT. Duta Putera Sumatera (Sun Motor Group) 12
CLA Electric System
Contoh Line tracking Legend
Jalur Circuit Positive A100 255 Central electrical system
Key
Circuit diagram
13/39
halaman 3, baris 4
Jalur circuit diagram pada
halaman ini berasal dari
circuit diagram halaman
13, baris 39
Ground
31000
X100 adalah
ground point pada
engine
compartment B1
ABS control unit, car radio, car two-way radio, part group, car
telephone, theft alarm system, device module, switching
A System, subassembly
device, control unit, cruise control
Blower motor, fan motor, pump motor for hydraulic units (ABS-
ASR-ESP), washer pump motor, windscreen wiper motor,
M Motor
starter motor, servo motor
Car antenna, shield part, shielded cable, cables of all kinds, line
W Transmission path, line, antenna bundles, earthing busbar
ELECTRIC
CIRCUIT DIAGRAMS
Main
switch
on
Ignition switch
on position 1
Sheet 1
Training & Development MAN Truck & Bus Asia Pacific
PT. Duta Putera Sumatera (Sun Motor Group) 22
CLA Electric System
Parking light Circuit
Sheet 7
Sheet 8
Sheet 2
A1 A2 B1 B2
40134x
D2
16108x
15002
Buzzer
D1
Note:
Cold water
K1-K4 : relay 5 pin 24vdc Sensor
Temperature sensor Sensor
D1-D2 : diode
60505 60513
A1
B1
K1
K2
A2
B2
Aplikasi
Jika terjadi Over Heat, Makan Relay K1 dan K2 akan aktif memutuskan power untuk
accelator pedal dan stalk switch memory. engine tetap runing, tetapi rpmnya akan
kembali ke idle (stationary) dan Buzzer akan bunyi selama sensor aktif ( saat terjadi
over heat engine, pada temperatur mendekati 104 - 105 oCelcius).
Training & Development MAN Truck & Bus Asia Pacific
PT. Duta Putera Sumatera (Sun Motor Group) 31
CLA Electric System
REAR VIEW(A100)
Main connection, negative (earth)
31000 6 br X100 Earthing point on engine
31000 4 br X244 Earthing point, instrument panel on left‐hand side
Main connection Æ ignition switch
terminal 15
Main connection Æ alternator B+
permanent positive terminal 30
Bridge to connection 91(30010)
Display & Instrument Panel (A407) Central Warning Lamps
1/ 3 Direction indicator.
2 Central warning light stop.
4 Tipper.
5 Engine Oil pressure.
6 Cooling water temperature.
7 Flame start system (optional).
8 Tilted cab.
9 Parking brake.
10 Head light high beam.
11 Brake circuits, reservoir pressure.
12 Battery charge indicator.
13/ 14 ABS fault in tractor/ trailer (optional).
15 ABS information trailer (optional).
16 Transmission fluid temperature (optional).
17 EDC (Electronic diesel control).
18 ASR (optional).
1. Speedometer. 2. Check & warning lamps panel. 19 Central lubrication system (optional).
3. RPM meter. 4. Panel Illumination Adj. switch. 20 Seat belt check.
5. Parking & Driving lights switch. 6. Rear Fog lamp switch. 21/ 22 ECAS fault & warning (optional).
1
1 Push the stalk forward/ backward for flash on Right /
Left side of the vehicle.
2
2 When the steering wheel has returned to the straight‐
ahead position, the stalk automatically springs back to
its rest position.
Windscreen Wiper/ Washer (S108/6)
Headlight high beam/Low beam (S108/8) 1
1. Switch on the headlight.
Turn the stalk in the direction indicated by the arrow so that
2. Press the stalk back until pressure point 1, high arrowhead (1) is in position.
beam light will stay until release of pressure.
“ 0 " = Off
3. Press the stalk back beyond pressure point "1" into "J " = Intermittent wipe (Approx. 10secs)
position "2“ for the High beam staying. The stalk
will automatically springs back to its rest position. “ I " = Slow wipe
4. Repeat the same procedure for getting the low “ II " = Fast wipe
beam. • Briefly press button (2) towards arrow (max. 0.9 seconds) = I
wiper cycle & Press button (2) for longer (0.9 to 6.5 seconds)
= 2 to 4 Cycles.
Stalk Switch(S157) Road speed control
Steering column stalk
1 1. Move forwards = "SET+' function.
2 2. Press "Memory" button = 'MEMORY"
function.
3. Light‐emitting diode “ON” = Road speed
limiter set.
5 4 3 4. Move “AUS" button back = "OFF" function.
5. Move backwards Arrow = “SET ‐" function.
After Switching ON the ignition, check lamp
(fig) in Panel and LED in the steering column
stalk switch come on for approx. 2‐3 seconds
(bulb check and self‐test). They go off if no
faults are found.
Note:
Do not PRESS the ACCELERATOR pedal when
starting the engine.
Instrument Cluster
Training & Development MAN Truck & Bus Asia Pacific
PT. Duta Putera Sumatera (Sun Motor Group) 40
CLA Electric System
K116 Relay, parking K119 Relay, headlight low and
K115 Relay, terminal 58 K118 Relay, rear fog
and tail lights high beams
lamp
K171 Relay,
consumer terminal
15
K110 Flasher Control
Unit
Fuse / auto cut for
Fuse / auto cut
tachograph
for cigar lighter
instrumentation,
terminal 30
K223 relay
Priority light
K180 Relay, ABS driver side
trailer, brake
lamp
Pull down
fuse, D+
Relay, priority
NC/KC
vehicle light
alternator
V368 Diode
engine brake via
brake lamp,
switch off
function
K675 Relay, rear Relay, ABS engine
fog light brake
K264 Relay, power
supply 15, EDC
K324 Relay
K170 Relay, power redundant
supply 30, EDC shut‐off (EDC)
A139 Control
Unit, ABS/ASR
R134 Resistor A435 Control
bank, EDC Unit, EDC
Sensor Element
Sistem elektronik yang digunakan pada kendaraan komersial berkembang cepat beberapa tahun terakhir.
Sistem elektronik sangat menentukan performa kendaraan. Sistem ini dulu hanya dianggap sebagai
penunjang tapi sekarang sekarang menjadi sektor kunci dengan teknologi modern. Sistem elektronik
kontrol menghasilkan performa kendaraan dan efektifitas komponen. Pada kesempatan ini istilah CAN-
line akan sering digunakan berkaitan dengan konteks ini.
Konsep dasar
CAN merupakan singkatan dari Control Area Network dan yang dimaksudkan sebagai sambungan kabel
kendaraan ECU dengan komponen-komponen lain. Sistem CAN berbeda-beda berdasarkan data-data
penting system elektronik dari berbagai kendaraan.
Sistem CAN-Line menggunakan sistem komunikasi two-way yang diterapkan pada kendaraan guna
menghemat kabel dan mencegah gangguan.pengiriman Informasi menggunakan protokol khusus antara
lain:
- Sinkronisasi informasi
- Hubungan dan respon antar sistem.
-Transmisi gangguan pada saat troubleshooting.
-Dan Iain-Iain.
Training & Development MAN Truck & Bus Asia Pacific
PT. Duta Putera Sumatera (Sun Motor Group) 49
CLA Electric System