(EXPERIMENT IV)
50
51
ion-ion Ca2+ dan Mg2+ dikenal sebagai air sadah atau “Hard Water”.
Ion-ion ini bisa berasal dari lumpur pada waktu member formasi
gypsum (CaSO4.2H2O).
4.3.2 Bahan :
1. NaHCO3
2. NaOH
3. CaCO3
4. Serbuk MgO
5. Kalium Kromat
6. Bentonite
7. Gypsum
8. Aquadest
9. Larutan H2SO4 0,02 N
10. Larutan AgNO3
11. Larutan KMnO4 0,1 N
12. Penolphalein
13. Methyl Jingga
14. Indikakor EBT
15. Larutan EDTA
Perhitungan :
1. Total Alkalinity =
M × Normalitas H 2 SO 4 ×1000
=epmTotal Alkalinity
ml Filtrate
2. CO2− Alkalinity
3
Jika ada OH - :
(M −P) × NH 2 SO 4 × 1000
ppm CO3-2 = × BMCO−2
3
ml Filtrate
3. OH- Alkalinity
(2 P−M )× NH 2 SO4 ×1000 −¿¿
Ppm OH- ¿ × BMOH
ml Filtrate
-
4. HCO3 Alkalinity
( M −2 P)× NH 2 SO4 ×1000
Ppm HCO3- ¿ × BMCO−¿¿
3
ml Filtrate
larutan M g+2
1. Mengambil 3 ml filtrate lumpur tersebut, memasukkan ke dalam labu
titrasi 250 ml.
2. Menambahkan 25 ml Aquadest, 5 ml larutan buffer pH 10 dan 3 tetes
indicator EBT.
3. Titrasi dengan EDTA standar sampai terjadi warna biru tua.
4. Catat volume pemakaian EDTA.
Reaksi yang terjadi:
Ca- + H2Y-2 → CaY-2 + 2 H+
Perhitungan :
ml EDTA × M EDTA ×1000
Kesadahan Total¿ =epm(Ca +2 + Mg +2)
ml Filtrate
4.6 Perhitungan
4.6.1. Alkalinitas
1. Total Alkalinity
M × Normalitas H 2 SO 4 ×1000
=epmTotal Alkalinity
ml Filtrate
57
4.7 Pembahasan
Pada saat kegiatan pemboran kontrol terhadap kualitas lumpur
selalu dilakukan, tujuannya adalah agar lumpur pemboran dapat
berfungsi sesuai dengan kondisi yang ada. Oleh karena itu, untuk
58
dapatkan pH lumpur 12, alkalinitas total 32,33 epm, CO3- 460 ppm,
-
lumpur stabil dan kondisinya baik. Jika sumbernya dari CO3
menunjukkan lumpur tidak stabil namun masih dapat dikontrol. Jika
sumbernya HCO3- kondisi lmpur sangat buruk dan sulit untuk dikontrol.
Pada percobaan ini lumpur terindikasi tidak stabil.
Lumpur yang kadar sadah terlalu tinggi (dipengaruhi oleh adanya
Ca2+ dan Mg2+) dapat menimbulkan kerak pada dinding pipa. Kerak
ini dapat dihilangkan dengan resin peluunak. Kandungan klorida yang
terlalu tinggi dapat menyebabkan kerusakan pada pipa pemboran.
59
Discussion
When drilling activities control the quality of sludge, it is always
carried out, the aim is that drilling mud can function in accordance with
existing conditions. Therefore, to maintain the quality of the sludge it is
necessary to have a Chemical Analysis to determine the content in our
sludge.
From the three tests that we have done, sludge is indicated to
contain CO3- and OH- ions. The results of the alkalinity test were
obtained mud pH 12, total alkalinity 32.33 epm, CO3-460 ppm, OH-ppm.
Testing for total hardness obtained mud pH 12 and total hardness value of
53.33 ppm. Determination of chloride content obtained pH of mud 10 and
chloride content of 1947 epm.
EPM stands for Equivalent Per Million which is a unit of
concentration. Close with ppm (parts per million), epm is used by mud
engineers. The epm of a substance is obtained by dividing the ppm by its
valence.
High alkalinity is caused by the presence of biarbonate and the
residual carbonate and mud hydroxide, this results in a change and there
are salt compounds and weak deposits. However, if the alkalinity is low
and unbalanced with high hardness, it can cause CaCO3 scale on the wall
of the installation pipe so that it can
reduce / narrow the pipe section. The source of alkalinity in the sludge
which only comes from OH ions indicates that the sludge is stable and in
good condition. If the source is CO3 - it shows that the mud is unstable
but can still be controlled. If the source is HCO3 - the condition is very
bad and difficult to control. In this experiment the sludge is indicated to be
unstable.
Sludge that is too hard to contain (influenced by the presence of Ca2 +
and Mg2 +) can cause crust on the pipe wall. This scale can be removed
with softener resin. Chloride content that is too high can cause damage to
60
4.8 Kesimpulan
Berdasarkan percobaan yang telah dilakukan, maka ditarik1. dapat
disimpulkan:
Kandungan ion-ion dalam lumpur mempengaruhi sifat dan content
lumpur pemboran.
32,33 epm, CO3- 460 ppm, OH- ppm. Pengujian kesadahan total didapatkan
pH lumpur 12 dan nilai kesadahan total sebesar 53,33 ppm. Penentuan
kandungan klorida didapatkan pH lumpur 10 dan kandungan klorida sebesar
1947 epm.
pH pada alkalinitas 12, kesadahan total 12, kandungan klorida 10, ketiga
pH tersebut basa dan sesuai dengan pH lumpur yang di inginkan (8,5-
12)
4.9 Tugas
1. Jelaskan kegunaan oenentuan alkalinitas, kandungan klorida dan
kesadahan total!
Jawaban :
- Kegunaan penentuan alkalinitas adalah untuk mengetahui kelarutan batu
kapur yang masuk ke sistem lumpur pada saat pemboran menembus
formasi limestone.
- Kegunaan penentuan kandungan klorida untuk mengetahui kontainasi
dara saat pemboran menembus formasi garam ataupun kontaminasi
garam yang berasal dari air formasi.
- Kegunaan penentuan kesadahan total untuk mengetahui kesadahan
lumpur pemboran yang berasal dari lumpur pada saat menembus
61
formasi gypsum.