DAFTAR ISI
1. Pekerjaan DED ini dilakukan pada tahun 2009 dengan Kriteria Desain untuk Struktur mengacu pada
Peraturan Pembebanan Jembatan RSNI T-02-2005 dan Peraturan Gempa Jembatan SNI 2833 -2008.
Saat ini perencanaan jembatan seharusnya mengacu pada peraturan Pembebanan Jembatan terbaru
yaitu SNI 1725-2016 dan peraturan Gempa Jembatan terbaru RSNI 2833-2013. Sehubungan hal
tersebut maka Kriteria Desain dan Perencanaan Jembatan sebaiknya diperiksa apakah sudah
memenuhi persyaratan mengacu pada peraturan yang terbaru.
1. Laporan Analisa dan Perhitungan Struktur Jembatan tidak tersedia sehingga untuk review jembatan
dilakukan back calculation untuk memeriksa hasil DED struktur jembatan berdasarkan Peraturan
Pembebanan terbaru yaitu :
a. Peraturan Pembebanan Jembatan SNI 1725 – 2016
b. Peraturan Perencanaan Gempa Jembatan RSNI 2833 – 2013
2. Pemeriksaan terutama dilakukan untuk Struktur Bawah dan Pondasi dikarenakan untuk beban-beban
pada struktur atas tidak ada perubahan dari peraturan pembebanan yang lama.
3. Analisa struktur jembatan akibat Gempa dilakukan dengan metode Gaya gempa Statik Ekivalen dari
hasil penurunan Analisa Respon Spektrum berdasarkan Peta Gempa 1000 tahun dengan probabilitas
terlampaui 7% dalam 75 tahun. Kondisi tanah dikategorikan jenis Tanah Keras (SC) dan lokasi proyek
masuk ke dalam Zona Gempa dengan percepatan gempa sebagai berikut:
a. PGA = 0.3g
b. Periode 0.2 detik = 0.5g
c. Periode 1 detik = 0.3 g
d. Peak acceleration pada 0.2 detik adalah 0.6 dan koefisien gempa static equivalent Kh dengan R=4
adalah 0.15
4. Analisa back calculation struktur jembatan dilakukan dengan perhitungan menggunakan model
program SAP2000 dengan material, section properties dan dimensi-dimensi sesuai dengan DED yang
ada dengan mengaplikasikan pembebanan yang paling critical yaitu:
a. Beban pada kondisi Normal : DL+SDL+LL
b. Beban pada kondisi Gempa : DL+SDL+LL+EQ
5. Jembatan Sungai Grenjeng direncanakan dengan system :
a. Multi Span Bridge dengan 3 bentang, dengan panjang total jembatan 72.23m. Jembatan
merupakan jembatan Main Road melintas diatas Sungai Putih.
b. Struktur Atas merupaka composite PC-I Girder, bentang 20+30+20m, dengan system
artikulasi/sambungan Simple Supported Joint. Jarak ctc Girder 2.1m dengan mutu beton fc’ 42
MPa tidak memenuhi standard (jarak ctc max utk fc’ 42MPa adalah 1.85m). Sudut skew jembatan
= 90o
c. Pier merupakan tipe Dinding/Wall dengan tinggi P1=10.7m dan P2=10.0m. Lebar pierhead 12.2m
dan ukuran penampang kolom/wall adalah 8.2x1.2m2.
d. Pondasi Pier berupa pondasi tiang RC Bored Pile diameter 800mm dengan konfigurasi 4x4 = 16
pile dan kedalaman bored pile L=14m (P1 & P2). Ukuran pilecap/footing LxBxD =
9.2x9.2x(1.3+0.5)m3
e. Abutment berupa tipe Spill Through dengan ukuran tinggi 2.95m dan panjang pilecap 4.4m dan
lebar 12.55m.
f. Pondasi pada Abutment berupa pondasi tiang RC Bored Pile diameter 800mm dengan konfigurasi
2x4 pile dan kedalaman bor L=22m (A1) dan L=24m (A2).
6. Dari hasil analisa perhitungan maka dilakukan pemeriksaan struktur untuk Pier untuk memastikan
memadainya kekuatan dan stabilitas struktur terhadap pembebanan yang kritis.
7. Pemeriksaan Pondasi Pier dan Abutment dengan konfigurasi hasil DED untuk memastikan keamanan
terhadap reaksi dari sub-struktur dengan pembebanan yang kritis tersebut.
1. Struktur Atas (PC-I Girder) dengan jarak ctc 2.1m menggunakan mutu beton fc’ 42MPa tidak
memenuhi standard yang ada. Sebaiknya digunakan fc’ 50 MPa.
2. Pier Jembatan
a. Hasil Analisa struktur pada struktur Pier menunjukkan bahwa komposisi dimensi dan penulangan
pada Pier sudah memadai.
b. Pemeriksaan Pilecap/footing dilakukan pada pier dengan menggunakan beban hasil reaksi tiang
yang terjadi. Hasil pemeriksaan penulangan pada Footing menunjukkan bahwa penulangan
sudah memadai namun mutu beton footing pada Pier disarankan untuk ditingkatkan dari 21MPa
menjadi 30MPa.
3. Abutment
a. Dari hasil pemeriksaan untuk abutment jembatan didapatkan dimensi dan penulangan abutment
sudah memadai
b. Hasil Analisa Pilecap/Footing Abutment menunjukkan bahwa penulangan utama dalam DED
sudah memadai.
5. Kesimpulan :
a. Dimensi dan penulangan untuk Pier jembatan sudah memadai, namun mutu beton untuk
Footing Pier perlu ditingkatkan
b. Dimensi dan penulangan pada abutment sudah memadai
6. Revisi :
a. Revisi mutu beton untuk PC-I Girder dari 41 MPa menjadi 50 MPa untuk Girder dengan jarak ctc
> 1.85m
b. Revisi mutu beton untuk footing/pilecap Pier dari 20 MPa menjadi 30 MPa sehingga penulangan
Footing Pier tidak perlu direvisi lagi.
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN SUNGAI GRENJENG
BRIDGE DIMENSION
Carriageway Width
11.70 0.00 0.50
Sidewalk
Pavement thick = 50 mm t= 0 mm
2.10 1.025
BRIDGE CROSS SECTION IN SKEW DIRECTION
Bridge Width
12.55
Carriageway Width
11.70 0.00 0.50
Sidewalk
2.10 1.025
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN SUNGAI GRENJENG
E. STEEL REINFORCEMENT
Steel Quality BJTD - 40
Yield Strength (fy) 390 MPa
Allowable Tension Stress 173.5 MPa
Allowable Compression Stress 112 MPa
Modulus Elasticity 200000 MPa
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN SUNGAI GRENJENG
4. SECTION PROPERTIES
Geometric properties of the cross-section
SPAN 20M DECK AT MID-SPAN
Parameter Value
A Cross sectional area 5.2 m^2
Av,y Conventional shearing area along Y-axis 1.47 m^2
Av,z Conventional shearing area along Z-axis 2.29 m^2
α Angle between Y-Z and U-V axes 89.977 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 1.24 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 65.35 m^4
It Torsional moment of inertia (St. Venant) 0.1 m^4
Iw Warping constant 13.67 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.49 m
iz Radius of gyration about axis parallel to Z passing through centroid 3.55 m
W u+ Max elastic modulus about U-axis 10.4 m^3
W u- Min elastic modulus about U-axis 10.43 m^3
W v+ Max elastic modulus about V-axis 1.23 m^3
W v- Min elastic modulus about V-axis 2.62 m^3
W pl,u Plastic modulus about U-axis 16.07 m^3
W pl,v Plastic modulus about V-axis 2.17 m^3
Iu Moment of inertia about U-axis 65.35 m^4
Iv Moment of inertia about V-axis 1.24 m^4
iu Radius of gyration about U-axis 3.55 m
iv Radius of gyration about V-axis 0.49 m
au+ Centroid to edge of compression zone along +ve U-axis 0.24 m
au- Centroid to edge of compression zone along -ve U-axis 0.5 m
av+ Centroid to edge of compression zone along +ve V-axis 2 m
av- Centroid to edge of compression zone along -ve V-axis 2.01 m
yM Distance to centroid along Y-axis -0.01 m
zM Distance to centroid along Z-axis -0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -0.58 m
Zb Distance to shear centre along Z-axis 0.67 m
P Perimeter 46 m
Pi Internal perimeter 0 m
Pe External perimeter 46 m
I1 Moment of inertia about Y-axis 1.24 m^4
I2 Moment of inertia about Z-axis 65.35 m^4
I12 Product of inertia about the centroid -0.03 m^4
Ip Polar moment of inertia about centroid 66.59 m^4
ip Polar radius of gyration about centroid 3.58 m
Wp Polar elastic modulus about centroid 1.68 m
Parameter Value
A Cross sectional area 6.97 m^2
Av,y Conventional shearing area along Y-axis 3.05 m^2
Av,z Conventional shearing area along Z-axis 2.26 m^2
α Angle between Y-Z and U-V axes 89.978 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 1.51 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 86.09 m^4
It Torsional moment of inertia (St. Venant) 0.36 m^4
Iw Warping constant 13.58 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.47 m
iz Radius of gyration about axis parallel to Z passing through centroid 3.51 m
W u+ Max elastic modulus about U-axis 13.69 m^3
W u- Min elastic modulus about U-axis 13.75 m^3
W v+ Max elastic modulus about V-axis 1.67 m^3
W v- Min elastic modulus about V-axis 2.67 m^3
W pl,u Plastic modulus about U-axis 21.38 m^3
W pl,v Plastic modulus about V-axis 2.89 m^3
Iu Moment of inertia about U-axis 86.09 m^4
Iv Moment of inertia about V-axis 1.51 m^4
iu Radius of gyration about U-axis 3.51 m
iv Radius of gyration about V-axis 0.47 m
au+ Centroid to edge of compression zone along +ve U-axis 0.24 m
au- Centroid to edge of compression zone along -ve U-axis 0.38 m
av+ Centroid to edge of compression zone along +ve V-axis 1.96 m
av- Centroid to edge of compression zone along -ve V-axis 1.97 m
yM Distance to centroid along Y-axis -0.01 m
zM Distance to centroid along Z-axis -0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -0.98 m
Zb Distance to shear centre along Z-axis 0.86 m
P Perimeter 42.93 m
Pi Internal perimeter 0 m
Pe External perimeter 42.93 m
I1 Moment of inertia about Y-axis 1.51 m^4
I2 Moment of inertia about Z-axis 86.09 m^4
I12 Product of inertia about the centroid -0.03 m^4
Ip Polar moment of inertia about centroid 87.6 m^4
ip Polar radius of gyration about centroid 3.54 m
Wp Polar elastic modulus about centroid 2.2 m
Parameter Value
A Cross sectional area 6.83 m^2
Av,y Conventional shearing area along Y-axis 2.32 m^2
Av,z Conventional shearing area along Z-axis 2.4 m^2
α Angle between Y-Z and U-V axes 89.97 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 3.05 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 84.47 m^4
It Torsional moment of inertia (St. Venant) 0.22 m^4
Iw Warping constant 31.21 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.67 m
iz Radius of gyration about axis parallel to Z passing through centroid 3.52 m
W u+ Max elastic modulus about U-axis 13.43 m^3
W u- Min elastic modulus about U-axis 13.49 m^3
W v+ Max elastic modulus about V-axis 2.49 m^3
W v- Min elastic modulus about V-axis 4.37 m^3
W pl,u Plastic modulus about U-axis 20.96 m^3
W pl,v Plastic modulus about V-axis 4.12 m^3
Iu Moment of inertia about U-axis 84.47 m^4
Iv Moment of inertia about V-axis 3.05 m^4
iu Radius of gyration about U-axis 3.52 m
iv Radius of gyration about V-axis 0.67 m
au+ Centroid to edge of compression zone along +ve U-axis 0.36 m
au- Centroid to edge of compression zone along -ve U-axis 0.64 m
av+ Centroid to edge of compression zone along +ve V-axis 1.97 m
av- Centroid to edge of compression zone along -ve V-axis 1.97 m
yM Distance to centroid along Y-axis -0.01 m
zM Distance to centroid along Z-axis -0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -0.73 m
Zb Distance to shear centre along Z-axis 1.08 m
P Perimeter 50.41 m
Pi Internal perimeter 0 m
Pe External perimeter 50.41 m
I1 Moment of inertia about Y-axis 3.05 m^4
I2 Moment of inertia about Z-axis 84.47 m^4
I12 Product of inertia about the centroid -0.04 m^4
Ip Polar moment of inertia about centroid 87.52 m^4
ip Polar radius of gyration about centroid 3.58 m
Wp Polar elastic modulus about centroid 2.19 m
Parameter Value
A Cross sectional area 10 m^2
Av,y Conventional shearing area along Y-axis 5.9 m^2
Av,z Conventional shearing area along Z-axis 2.4 m^2
α Angle between Y-Z and U-V axes 89.976 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 3.59 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 121.58 m^4
It Torsional moment of inertia (St. Venant) 1 m^4
Iw Warping constant 27.35 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.6 m
iz Radius of gyration about axis parallel to Z passing through centroid 3.49 m
W u+ Max elastic modulus about U-axis 19.32 m^3
W u- Min elastic modulus about U-axis 19.43 m^3
W v+ Max elastic modulus about V-axis 3.19 m^3
W v- Min elastic modulus about V-axis 4.48 m^3
W pl,u Plastic modulus about U-axis 30.46 m^3
W pl,v Plastic modulus about V-axis 5.29 m^3
Iu Moment of inertia about U-axis 121.58 m^4
Iv Moment of inertia about V-axis 3.59 m^4
iu Radius of gyration about U-axis 3.49 m
iv Radius of gyration about V-axis 0.6 m
au+ Centroid to edge of compression zone along +ve U-axis 0.32 m
au- Centroid to edge of compression zone along -ve U-axis 0.45 m
av+ Centroid to edge of compression zone along +ve V-axis 1.93 m
av- Centroid to edge of compression zone along -ve V-axis 1.94 m
yM Distance to centroid along Y-axis -0.01 m
zM Distance to centroid along Z-axis -0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -1.07 m
Zb Distance to shear centre along Z-axis 1.28 m
P Perimeter 47.13 m
Pi Internal perimeter 0 m
Pe External perimeter 47.13 m
I1 Moment of inertia about Y-axis 3.59 m^4
I2 Moment of inertia about Z-axis 121.58 m^4
I12 Product of inertia about the centroid -0.05 m^4
Ip Polar moment of inertia about centroid 125.17 m^4
ip Polar radius of gyration about centroid 3.54 m
Wp Polar elastic modulus about centroid 3.11 m
5. STRUCTURE MODEL
SAP2000 2-2-17 2:05:35
SAP2000 v14.0.0 - File:KBS SGRENJENG - Moment 3-3 Diagram (DEAD) - KN, m, C Units
SAP2000 2-2-17 2:39:29
SAP2000 v14.0.0 - File:KBS SGRENJENG - Shear Force 2-2 Diagram (DEAD) - KN, m, C Units
SAP2000 2-2-17 2:32:30
! "! #
! "
# $ ! %
& ' $ ! () * % % ! + (, + - &#. " /
# $ ! / 0 * () * % % ! + (, + - " /,
# $ ! * () * % % ! + (, + - " /
. *! * - &#. " /
. *! / * - " /
. *! * - 1 " /,
* *
. " &#. &#. " / 2 " 3 " /(,
" " /; 2 " / 2 " / ,
" 1 " /:,
* - " :/ 8$ 1 ! . !+
$ $ %&'
/(
/;
/,
/:
/
/ /, / /, / /, /
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN SUNGAI GRENJENG
7. BRIDGE LOADINGS
Jembatan Sungai Grenjeng
LOADING - SPAN = 30 m
A. DEAD LOAD
1. Girder Selfweight
a. At Mid Span = 101.78 kN/m
b. At End Span = 180.91 kN/m
70 mm
1410
3. Diaphragm
a. At Mid Span 3 x 57.6875 = 173.06 kN
distributed load = 6.46 kN/m
B. SUPERIMPOSED LOAD
C. LIVE LOAD
1. D-Load
a. UDL (2.75x4x9)+(0.7x4.5) = 102.15 kN/m
b. KEL (with impact) 11.7 x 68.6 = 802.62 kN 30.00
c. Brake 5% x D-Load = 6.41 kN/m
2. Truck Load
11 4 5 10
30
Jembatan Sungai Grenjeng
LOADING - SPAN = 20 m
A. DEAD LOAD
1. Girder Selfweight
a. At Mid Span = 60.98 kN/m
b. At End Span = 105.23 kN/m
70 mm
1610
3. Diaphragm
a. At Mid Span 3 x 54.6515 = 87.58 kN
distributed load = 5.12 kN/m
B. SUPERIMPOSED LOAD
C. LIVE LOAD
1. D-Load
a. UDL (2.75x4x9)+(0.7x4.5) = 102.15 kN/m
b. KEL (with impact) 11.7 x 68.6 = 802.62 kN 20.00
c. Brake 5% x D-Load = 7.06 kN/m
2. Truck Load
11 4 5 10
30
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN SUNGAI GRENJENG
8. PIER DESIGN
PIER COLUMN DESIGN
JEMBATAN SUNGAI GRENJENG
PIER COLUMN FORCES
TABLE: Element Forces - Frames
Frame Station OutputCase CaseType StepType P V2 V3 T M2 M3
Text m Text Text Text KN KN KN KN-m KN-m KN-m
(Pmax)
y
x
150000
8200 x 1200 mm
Units: Metric
fs=0
Run axis: About X-axis
-50000 (Pmin)
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-5\5.1. JEMBATAN SUNGAI G
Project: JEMBATAN SUNGAI GRENJENG
Column: PIER P1 Engineer: HW
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 30 MPa fy = 390 MPa
Ec = 25743 MPa Es = 200000 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.83245
Section:
========
Rectangular: Width = 8200 mm Depth = 1200 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Spiral; #19 ties with #32 bars, #19 with larger bars.
phi(a) = 0.85, phi(b) = 0.9, phi(c) = 0.7
Layout: Rectangular
Pattern: Sides Different (Cover to transverse reinforcement)
Total steel area, As = 122850 mm^2 at 1.25%
Top Bottom Left Right
-------- -------- -------- --------
Bars 70 #32 70 #32 5 #32 5 #32
Cover(mm) 100 100 100 100
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 19313.0 179.0 30567.4 170.767
2 12177.0 11737.0 27388.5 2.334
A. Longitudinal Direction
1400
1500
100
b1
1000
fc' = 21 MPa
Allowable Stresses (Normal) : Allowable Stresses (E-quake) :
σcv-a = 8.30 Mpa (σch-a) σcv-a = 12.45 Mpa (σch-a)
τcv-a = 0.36 Mpa (τch-a) τcv-a = 0.54 Mpa (τch-a)
1400
1500
100
b1
1000
Width B = 9.20 m
PILECAP SECTION
1.00 a
b
0.50
1
1.30 2
O
P-3 P-2 P-1
0.00 0.00
2.90 1.00
3.90
PILE REACTION
Npile/row = 5 pile
Normal Equake
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 105.20 ton 142.70 ton
P-max2 = 105.20 ton 142.70 ton
o o
α= 0.00 0.00
P-1 = 526.00 ton 713.50 ton
Mo-1 = 1525.40 ton-m 2069.15 ton-m
6.05 11.15
Xo = 1.85 m
Self-W = 139.04 ton
Moment Mo = 256.54 ton-m
SOIL WEIGHT
A X Ax
4.88 10.14
Xo = 2.08 m
Soil-W = 80.73 ton
Moment Mo = 167.92 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
1.70 m
As
0.10 m
9.20 m
d= 1684 mm
b= 9200 mm
β= 0.85
φ= 0.8
a= 52.31 mm
Numb = 91 bars
As = 73187 mm2 > req --- OK !!
Bott 32 100 91 68
SHEAR REINFORCEMENT
φ= 0.7
Shear Vu = 6.06E+06 N
Vc = 1.42E+07 N
φVc = 9.92E+06 N > Vu --->No Stirrups required !!
Vs = 0.00E+00 N
Take S = 1200 mm (transverse dir.)
Av-req = 0 mm2
Use Dia. = 16 mm (F7)
Number req. = 2 bars
Av = 402 mm2 > req --- OK !!
Distance = 3900.0 mm take : 600 mm (longitudinal dir)
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F4 F2
D32-200 D32-200
F7
D16-600/1200
(Shear)
D32-200 (2 Layers)
D32-200 F1
F3
LONGITUDINAL DIRECTION
PILECAP BOTTOM REINFORCEMENT - TRANSVERSAL DIRECTION
fc' = 30 Mpa Conc Dens = 2.50 t/m3
fy = 390 Mpa Soil Dens = 1.80 t/m3
Width B = 9.20 m
PILECAP SECTION
1.00 a
b
0.50
1
1.30 2
O
P-3 P-2 P-1
0.00 0.00
1.45 1.00
1.70
PILE REACTION
Npile/row = 4 pile
Normal Transient
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 105.20 ton 144.80 ton
P-max2 = 105.20 ton 144.80 ton
o o
α= 0.00 0.00
P-1 = 420.80 ton 579.20 ton
Mo-1 = 610.16 ton-m 839.84 ton-m
2.64 2.24
Xo = 0.85 m
Self-W = 60.61 ton
Moment Mo = 51.51 ton-m
SOIL WEIGHT
A X Ax
2.08 1.87
Xo = 0.90 m
Soil-W = 34.36 ton
Moment Mo = 30.97 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
1.70 m
As
0.10 m
9.20 m
d= 1684 mm
b= 9200 mm
β= 0.85
φ= 0.8
a= 24.03 mm
Numb = 46 bars
As = 36995 mm2 > req --- OK !!
φ= 0.7
Shear Vu = 6.01E+06 N
Vc = 1.42E+07 N
φVc = 9.92E+06 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F2 F4
D32-200 D32-200
F7
D16-1200/600
(Shear)
D32-200
D32-200 (2 Layers) F3
F1
TRANSVERSAL DIRECTION
PILECAP TOP REINFORCEMENT - LONGITUDINAL DIRECTION
Width B = 9.20 m
PILECAP SECTION
1.00 a
b
0.50
1
1.30 2
O
P-3 P-2 P-1
0.00 0.00
2.90 1.00
3.90
PILE REACTION
Npile/row = 5 pile
Normal Transient
Row 3 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-min1 = 104.00 ton 13.90 ton
P-min2 = 104.00 ton 13.90 ton
o o
α= 0.00 0.00
P-1 = 520.00 ton 69.50 ton
Mo-1 = 1508.00 ton-m 201.55 ton-m
6.05 11.15
Xo = 1.85 m
Self-W = 139.04 ton
Moment Mo = 256.54 ton-m
SOIL WEIGHT
A X Ax
4.88 10.14
Xo = 2.08 m
Soil-W = 80.73 ton
Moment Mo = 167.92 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As
1.70 m
9.20 m
d= 1684 mm
b= 9200 mm
β= 0.85
φ= 0.8
a= 8.89 mm
Numb = 46 bars
As = 36995.40 mm2 > req --- OK !!
Width B = 9.20 m
PILECAP SECTION
1.00 a
b
0.50
1
1.30 2
O
P-3 P-2 P-1
0.00 0.00
1.45 1.00
1.70
PILE REACTION
Npile/row = 4 pile
Normal Transient
Row 3 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-min1 = 104.00 ton 16.50 ton
P-min2 = 104.00 ton 16.50 ton
o o
α= 0.00 0.00
P-1 = 416.00 ton 66.00 ton
Mo-1 = 603.20 ton-m 95.70 ton-m
2.64 2.24
Xo = 0.85 m
Self-W = 60.61 ton
Moment Mo = 51.51 ton-m
SOIL WEIGHT
A X Ax
2.08 1.87
Xo = 0.90 m
Soil-W = 34.36 ton
Moment Mo = 30.97 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As
1.70 m
9.20 m
d= 1652 mm
b= 9200 mm
β= 0.85
φ= 0.8
a= 0.30 mm
Numb = 46 bars
As = 36995 mm2 > req --- OK !!
9. ABUTMENT DESIGN
ABUTMENT A1
ABUTMENT A1 DESIGN
1. FOUNDATION ANALYSIS
PILE ARRANGEMENT : 2 x 4
Ka = 0.2972
1.25 Kea = 0.4073
Eq-coef = 0.15
1.09 a
3
2.95 0.00 Pile Diameter = 0.80 m
0.60 Distance from Edge = 1.00 m
Pile Row = 2 pile
Pile per Row = 4 pile
Pile dist. (transv) = 3.38 m
0.00 Pilecap Width = 12.55 m
b
5.00
selfweight SW = 2334.7 kN
eccintricity moment MoSW = -559.3 kN-m
SUPERSTRUCTURE (REACTION)
SOIL WEIGHT
W-soil = 307.8 kN
eccentricity moment Mo-soil = -484.8 kN-m
EARTH PRESSURE
Ep1 = 292.1 kN
Mo-Ep1 = 287.2 kN-m
Earthquake Time :
Ep1 = 400.4 kN
Mo-Ep1 = 393.7 kN-m
1. NORMAL TIME
Load LF V HX MoX
kN kN kN-m
Bearing Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
299 251 550 275 183
Pullout Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
299 0 299 150 100
P ( kN)
12000
(Pmax)
8000
4000 fs=0
fs=0.5fy
3 21
Mx (k N-m)
(Pmin)
-4000
2. COEFFICIENT OF EARTH PRESSURE
1) Permanent Time
cos2 (φ - θ)
Ka = 2
cos2 θ cos (θ + δ) 1 + sin (φ + δ) sin (δ - α)
2) Transient Time
cos2 (φ - θ0 - θ )
Kea =
cos θ0 cos2 θ cos (θ + θ0 + δ) (1+ Xa) 2
where ;
δ : Angle of wall friction
For stability calculation = φ/2 = 15 degree
For sectional calculation = 0 degree
θ 0 = tan -1 kh = 8.531 degree
kh = 0.15
1230
1330
100
b1
1000
1230
1330
100
b1
1000
Width B = 12.55 m
PILECAP SECTION
0.00 a
1
1.33
O
Pc Pb Pa
0.00 0.00
1.55 1.00
2.55
PILE REACTION
Npile/row = 4 pile
Normal Equake
Row 3 :
Pc-max1 = 0.00 ton 0.00 ton
Pc-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
Pb-max1 = 0.00 ton 0.00 ton
Pb-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
Pb = 0.00 ton 0.00 ton
Mo-b = 0.00 ton-m 0.00 ton-m
Row 1 :
Pa-max1 = 80.47 ton 71.24 ton
Pa-max2 = 80.47 ton 71.24 ton
o o
α= 0.00 0.00
Pa = 321.87 ton 284.97 ton
Mo-a = 498.90 ton-m 441.71 ton-m
3.39 4.32
Xo = 1.28 m
Self-W = 106.41 ton
Moment Mo = 135.67 ton-m
SOIL WEIGHT
A X Ax
0.00 0.00
Xo = 0.00 m
Soil-W = 0.00 ton
Moment Mo = 0.00 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
1.23 m
As
0.10 m
12.55 m
d= 1192.5 mm
b= 12550 mm
β= 0.85
φ= 0.8
a= 24.33 mm
Numb = 84 bars
As = 41233 mm2 > req --- OK !!
SHRINKAGE REINFORCEMENT
Numb = 7 bars/m
As = 3436 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 3.76E+06 N
Vc = 1.12E+07 N
φVc = 7.82E+06 N > Vu --->No Stirrups required !!
Vs = -4.06E+06 N
Take S = 1200 mm (transverse dir.)
Av-req = 0 mm2
Use Dia. = 16 mm (A6)
Number req. = 2 bars
Av = 402 mm2 > req --- OK !!
Distance = 2550.00 mm take : 600 mm (longitudinal dir)
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
A4 A2
D19-150 D19-150
A6
D16-600/1200
(Shear)
D25-150
D25-150 A1
A3
LONGITUDINAL DIRECTION
PILECAP TOP REINFORCEMENT
Width B = 12.55 m
PILECAP SECTION
0.00 a
1
1.33
O
Pf Pe Pd
0.00 0.00
0.78 1.00
1.25
PILE REACTION
Npile/row = 4 pile
Normal Transient
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 80.47 ton 71.24 ton
P-max2 = 80.47 ton 71.24 ton
o o
α= 0.00 0.00
P-1 = 321.87 ton 284.97 ton
Mo-1 = 249.45 ton-m 220.85 ton-m
1.66 1.04
Xo = 0.63 m
Self-W = 52.16 ton
Moment Mo = 32.60 ton-m
SOIL WEIGHT
A X Ax
0.00 0.00
Xo = 0.00 m
Soil-W = 0.00 ton
Moment Mo = 0.00 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As 1.23 m
12.55 m
d= 1195.5 mm
b= 12550 mm
β= 0.85
φ= 0.8
a= 13.47 mm
Numb = 84 bars
As = 23816.41 mm2 > req --- OK !!
SHRINKAGE REINFORCEMENT
Numb = 7 bars/m
As = 1985 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 4.31E+06 N
Vc = 1.12E+07 N
φVc = 7.84E+06 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
A2 A4
D19-150 D19-150
A6
D16-1200/600
(Shear)
D25-150
D25-150 A3
A1
TRANSVERSAL DIRECTION
ABUTMENT A2
ABUTMENT A2 DESIGN
1. FOUNDATION ANALYSIS
PILE ARRANGEMENT : 2 x 4
Ka = 0.2972
1.25 Kea = 0.4073
Eq-coef = 0.15
1.09 a
3
2.95 0.00 Pile Diameter = 0.80 m
0.60 Distance from Edge = 1.00 m
Pile Row = 2 pile
Pile per Row = 4 pile
Pile dist. (transv) = 7.55 m
0.00 Pilecap Width = 12.55 m
b
5.00
selfweight SW = 2334.7 kN
eccintricity moment MoSW = -559.3 kN-m
SUPERSTRUCTURE (REACTION)
SOIL WEIGHT
W-soil = 307.8 kN
eccentricity moment Mo-soil = -484.8 kN-m
EARTH PRESSURE
Ep1 = 292.1 kN
Mo-Ep1 = 287.2 kN-m
Earthquake Time :
Ep1 = 400.4 kN
Mo-Ep1 = 393.7 kN-m
1. NORMAL TIME
Load LF V HX MoX
kN kN kN-m
Bearing Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
466 251 718 359 239
Pullout Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
466 0 466 233 155
(Pmax)
8000
4000 fs=0
fs=0.5fy
3 21
M x (k N -m)
(Pmin)
-4000
2. COEFFICIENT OF EARTH PRESSURE
1) Permanent Time
cos2 (φ - θ)
Ka = 2
cos2 θ cos (θ + δ) 1 + sin (φ + δ) sin (δ - α)
2) Transient Time
cos2 (φ - θ0 - θ )
Kea =
cos θ0 cos2 θ cos (θ + θ0 + δ) (1+ Xa) 2
where ;
δ : Angle of wall friction
For stability calculation = φ/2 = 15 degree
For sectional calculation = 0 degree
θ 0 = tan -1 kh = 8.531 degree
kh = 0.15
1230
1330
100
b1
1000
1230
1330
100
b1
1000
Width B = 12.55 m
PILECAP SECTION
0.00 a
1
1.33
O
Pc Pb Pa
0.00 0.00
1.55 1.00
2.55
PILE REACTION
Npile/row = 4 pile
Normal Equake
Row 3 :
Pc-max1 = 0.00 ton 0.00 ton
Pc-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
Pb-max1 = 0.00 ton 0.00 ton
Pb-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
Pb = 0.00 ton 0.00 ton
Mo-b = 0.00 ton-m 0.00 ton-m
Row 1 :
Pa-max1 = 80.54 ton 71.49 ton
Pa-max2 = 80.54 ton 71.49 ton
o o
α= 0.00 0.00
Pa = 322.17 ton 285.97 ton
Mo-a = 499.37 ton-m 443.26 ton-m
3.39 4.32
Xo = 1.28 m
Self-W = 106.41 ton
Moment Mo = 135.67 ton-m
SOIL WEIGHT
A X Ax
0.00 0.00
Xo = 0.00 m
Soil-W = 0.00 ton
Moment Mo = 0.00 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
1.23 m
As
0.10 m
12.55 m
d= 1192.5 mm
b= 12550 mm
β= 0.85
φ= 0.8
a= 24.36 mm
Numb = 84 bars
As = 41233 mm2 > req --- OK !!
SHRINKAGE REINFORCEMENT
Numb = 7 bars/m
As = 3436 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 3.77E+06 N
Vc = 1.12E+07 N
φVc = 7.82E+06 N > Vu --->No Stirrups required !!
Vs = -4.06E+06 N
Take S = 1200 mm (transverse dir.)
Av-req = 0 mm2
Use Dia. = 16 mm (A6)
Number req. = 2 bars
Av = 402 mm2 > req --- OK !!
Distance = 2550.00 mm take : 600 mm (longitudinal dir)
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
A4 A2
D19-150 D19-150
A6
D16-600/1200
(Shear)
D25-150
D25-150 A1
A3
LONGITUDINAL DIRECTION
PILECAP TOP REINFORCEMENT
Width B = 12.55 m
PILECAP SECTION
0.00 a
1
1.33
O
Pf Pe Pd
0.00 0.00
0.78 1.00
1.25
PILE REACTION
Npile/row = 4 pile
Normal Transient
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 80.54 ton 71.49 ton
P-max2 = 80.54 ton 71.49 ton
o o
α= 0.00 0.00
P-1 = 322.17 ton 285.97 ton
Mo-1 = 249.68 ton-m 221.63 ton-m
1.66 1.04
Xo = 0.63 m
Self-W = 52.16 ton
Moment Mo = 32.60 ton-m
SOIL WEIGHT
A X Ax
0.00 0.00
Xo = 0.00 m
Soil-W = 0.00 ton
Moment Mo = 0.00 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As 1.23 m
12.55 m
d= 1195.5 mm
b= 12550 mm
β= 0.85
φ= 0.8
a= 13.48 mm
Numb = 84 bars
As = 23816.41 mm2 > req --- OK !!
SHRINKAGE REINFORCEMENT
Numb = 7 bars/m
As = 1985 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 4.31E+06 N
Vc = 1.12E+07 N
φVc = 7.84E+06 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
A2 A4
D19-150 D19-150
A6
D16-1200/600
(Shear)
D25-150
D25-150 A3
A1
TRANSVERSAL DIRECTION
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN SUNGAI GRENJENG
1 Abutment A1 DB-4 0.8 22 Normal 805 805 2240 -837 OK 16 730 805 1600 -767 OK
Earthquake 712 712 3360 -1255 OK 637 712 2400 -1150 OK
2 Abutment A2 DB-5 0.8 24 Normal 805 805 2390 -1553 OK 16 704 805 1940 -1103 OK
Earthquake 715 715 3585 -2330 OK 614 715 2910 -1655 OK
3 Pier P1 DB-4 0.8 14 Normal 1178 990 2190 -1353 OK 12 1153 990 1970 -1137 OK
Earthquake 1576 231 3285 -2030 OK 1551 231 2955 -1705 OK
4 Pier P2 DB-5 0.8 14 Normal 1228 1040 2010 -1170 OK 12 1203 1040 1970 -1137 OK
Earthquake 1624 139 3015 -1755 OK 1599 139 2955 -1705 OK
CATATAN:
Review single pile capacity dilakukan dengan cara merencanakan ulang kedalaman tiang
yang digunakan pada setiap sub structure untuk mendapatkan kapasitas daya dukung
tiang yang memadai
PILE GROUP ANALYSIS
JEMBATAN SUNGAI GRENJENG
FOUNDATION REACTION
TABLE: Joint Reactions
Joint OutputCase CaseType StepType F1 F2 F3 M1 M2 M3
Text Text Text Text KN KN KN KN-m KN-m KN-m
PILE L 14 M
PILE DIA. 0.8 M
PILE AREA 0.5027 M2
PILE SW 12.57 KN/M
NOTE:
COMB A = DL+SDL+LL
D COMB B = DL+SDL+LL+EQX
COMB C = DL+SDL+LL+EQY
1 2 3 4
PILE L 14 M
PILE DIA. 0.8 M
PILE AREA 0.5027 M2
PILE SW 12.57 KN/M
NOTE:
COMB A = DL+SDL+LL
D COMB B = DL+SDL+LL+EQX
COMB C = DL+SDL+LL+EQY
1 2 3 4
(Pmax)
y
x
8000
800 mm diam.
4000 fs=0
Code: ACI 318-02
(Pmin)
-4000
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-5\5.1. JEMBATAN SUNGAI G
Project: JEMBATAN SUNGAI GRENJENG
Column: BP800_A1 Engineer: HW
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 29 MPa fy = 390 MPa
Ec = 25310.3 MPa Es = 200000 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.839702
Section:
========
Circular: Diameter = 800 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Spiral; #13 ties with #25 bars, #13 with larger bars.
phi(a) = 0.85, phi(b) = 0.9, phi(c) = 0.7
Layout: Circular
Pattern: All Sides Equal (Cover to transverse reinforcement)
Total steel area, As = 8160 mm^2 at 1.62%
16 #25 Cover = 100 mm
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 1609.0 149.0 1021.7 6.857
2 1425.0 120.0 1011.5 8.429
3 1425.0 42.0 1011.5 24.083
(Pmax)
y
x
8000
800 mm diam.
4000 fs=0
Code: ACI 318-02
(Pmin)
-4000
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-5\5.1. JEMBATAN SUNGAI G
Project: JEMBATAN SUNGAI GRENJENG
Column: BP800_A2 Engineer: HW
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 29 MPa fy = 390 MPa
Ec = 25310.3 MPa Es = 200000 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.839702
Section:
========
Circular: Diameter = 800 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Spiral; #13 ties with #25 bars, #13 with larger bars.
phi(a) = 0.85, phi(b) = 0.9, phi(c) = 0.7
Layout: Circular
Pattern: All Sides Equal (Cover to transverse reinforcement)
Total steel area, As = 8160 mm^2 at 1.62%
16 #25 Cover = 100 mm
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 1611.0 149.0 1021.8 6.858
2 1430.0 121.0 1011.8 8.362
3 1430.0 42.0 1011.8 24.090
(Pmax)
y
x
8000
800 mm diam.
4000 fs=0
Code: ACI 318-02
(Pmin)
-4000
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-5\5.1. JEMBATAN SUNGAI G
Project: JEMBATAN SUNGAI GRENJENG
Column: BP800_P1 Engineer: HW
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 29 MPa fy = 390 MPa
Ec = 25310.3 MPa Es = 200000 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.839702
Section:
========
Circular: Diameter = 800 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Spiral; #13 ties with #25 bars, #13 with larger bars.
phi(a) = 0.85, phi(b) = 0.9, phi(c) = 0.7
Layout: Circular
Pattern: All Sides Equal (Cover to transverse reinforcement)
Total steel area, As = 8160 mm^2 at 1.62%
16 #25 Cover = 100 mm
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 1576.0 125.0 1019.9 8.160
2 204.0 125.0 821.1 6.569
(Pmax)
y
x
8000
800 mm diam.
4000 fs=0
Code: ACI 318-02
(Pmin)
-4000
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-5\5.1. JEMBATAN SUNGAI G
Project: JEMBATAN SUNGAI GRENJENG
Column: BP800_P2 Engineer: HW
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 29 MPa fy = 390 MPa
Ec = 25310.3 MPa Es = 200000 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.839702
Section:
========
Circular: Diameter = 800 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Spiral; #13 ties with #25 bars, #13 with larger bars.
phi(a) = 0.85, phi(b) = 0.9, phi(c) = 0.7
Layout: Circular
Pattern: All Sides Equal (Cover to transverse reinforcement)
Total steel area, As = 8160 mm^2 at 1.62%
16 #25 Cover = 100 mm
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 1624.0 141.0 1022.5 7.252
2 139.0 141.0 807.8 5.729