DAFTAR ISI
1. Pekerjaan DED ini dilakukan pada tahun 2009 dengan Kriteria Desain untuk Struktur mengacu pada
Peraturan Pembebanan Jembatan RSNI T-02-2005 dan Peraturan Gempa Jembatan SNI 2833 -2008.
Saat ini perencanaan jembatan seharusnya mengacu pada peraturan Pembebanan Jembatan terbaru
yaitu SNI 1725-2016 dan peraturan Gempa Jembatan terbaru RSNI 2833-2013. Sehubungan hal
tersebut maka Kriteria Desain dan Perencanaan Jembatan sebaiknya diperiksa apakah sudah
memenuhi persyaratan mengacu pada peraturan yang terbaru.
1. Laporan Analisa dan Perhitungan Struktur Jembatan tidak tersedia sehingga untuk review jembatan
dilakukan back calculation untuk memeriksa hasil DED struktur jembatan berdasarkan Peraturan
Pembebanan terbaru yaitu :
a. Peraturan Pembebanan Jembatan SNI 1725 – 2016
b. Peraturan Perencanaan Gempa Jembatan RSNI 2833 – 2013
2. Pemeriksaan dilakukan untuk Struktur Bawah dan Pondasi saja dikarenakan untuk beban-beban pada
struktur atas tidak ada perubahan dari peraturan pembebanan yang lama.
3. Analisa struktur jembatan akibat Gempa dilakukan dengan metode Gaya gempa Statik Ekivalen dari
hasil penurunan Analisa Respon Spektrum berdasarkan Peta Gempa 1000 tahun dengan probabilitas
terlampaui 7% dalam 75 tahun. Kondisi tanah dikategorikan jenis Tanah Keras (SC) dan lokasi proyek
masuk ke dalam Zona Gempa dengan percepatan gempa sebagai berikut:
a. PGA = 0.3g
b. Periode 0.2 detik = 0.5g
c. Periode 1 detik = 0.3 g
d. Peak acceleration pada 0.2 detik adalah 0.6 dan koefisien gempa static equivalent Kh dengan R=4
adalah 0.15
4. Analisa back calculation struktur jembatan dilakukan dengan pemodelan menggunakan program
SAP2000 dengan material, section properties dan dimensi-deimensi sesuai dengan DED yang ada
dengan mengaplikasikan pembebanan yang paling critical yaitu:
a. Beban pada kondisi Normal : DL+SDL+LL
b. Beban pada kondisi Gempa : DL+SDL+LL+EQ
5. Jembatan Akses Kali Putih direncanakan dengan system :
a. Multi Span Bridge dengan 3 bentang, dengan panjang total jembatan 108.9m
b. Struktur Atas merupaka composite PC-I Girder, bentang 32.45+44+50.0+32.45m, dengan system
artikulasi/sambungan Simple Supported Joint. Pierhead merupakan tipe table top (cantilever)
yang memberikan tambahan panjangspan sebesar 4m pada setiap pier.
c. Struktur Bawah berupa RC Concrete Abutment tipe Wall dan RC Concrete Pier dengan Twin
Circular Column dengan dimensi:
A1 dan A2 Wall Width = 1.3m
P1 ; P2 Circular Column diameter 2.0m
d. Tinggi Struktur Bawah adalah sebagai berikut:
A1 = 6.0m ; A2 = 5.5m ; P1 = 16.0m ; P2 = 15.0m
e. Pondasi berupa RC Bored Pile ukuran diameter 1500mm (seragam) dengan panjang tiang
bervariasi antara 10m s/d 15m. Kondisi lapisan tanah secara umum berupa tanah batuan yang
keras pada kedalaman antara 8 – 12m
6. Dari hasil running program maka dilakukan pemeriksaan struktur untuk Abutment dan Pier dimana
untuk pemeriksaan Pier Column dilakukan pada member forces yang paling kritis untuk memeriksa
apakah design kolom telah memadai. Pemeriksaan pondasi dilakukan untuk semua Abutment dan
Pier untuk memeriksa apakah Pile design memadai.
1. Konfigurasi PC-I Girder dengan jarak 2m dan mutu beton fc’ 41.5 MPa tidak memenuhi standard
girder yang ada. Disarankan untuk menaikkan mutu beton menjadi fc’ 50MPa
2. Pier Jembatan
a. Dari Analisa Pile Group pada jembatan Kali Putih-1 didapatkan bahwa reaksi tiang /pile pada
semua pier melampaui kapasitas ijin tiang tersebut yaitu pada Pier P1 dan P2. Rangkuman reaksi
tiang dapat dilihat pada table Pile Analysis Summary terlampir.
b. Hasil Analisa struktur pada kolom-kolom Pier menunjukkan bahwa komposisi dimensi dan
penulangan pada Pier sudah memadai.
c. Pemeriksaan Pilecap/footing dilakukan pada setiap pier dengan menggunakan beban hasil reaksi
tiang yang terjadi. Hasil pemeriksaan penulangan pada Footing menunjukkan bahwa penulangan
pada DED sudah memadai jika mutu beton footing pier ditingkatkan dari 20MPa menjadi 30MPa.
3. Abutment
a. Dari hasil Analisa pondasi tiang didapatkan gaya dalam tiang pada Abutment A1 tidak melampaui
kapasitas ijin tiang, sehingga konfigurasi dan kedalaman tiang sudah memadai. Pada Abutment
A2 gaya tiang melampaui kapasitas tiang sehingga kedalaman harus diperbesar untuk
meningkatkan kapasitas tiang
b. Hasil Analisa Dinding (Wall) Abutment menunjukkan bahwa penulangan utama dalam DED sudah
memadai.
c. Dari hasil perhitungan penulangan pada Footing A1 dan A2 didapatkan tulangan utama tidak
memadai dan perlu direvisi.
5. Kesimpulan :
a. PC-I Girder jarak 2m dengan mutu beton fc’ 41.5 MPa tidak memadai untuk bentang s/d 40m
sedangkan untuk PC-I Girder bentang 45m disarankan untuk meningkatkan mutu beton menjadi
fc’ 60 MPa.
b. Kapasitas pondasi tiang pada semua Pier jembatan tidak memenuhi untuk mengantisipasi reaksi
tiang yang terjadi
c. Dimensi dan penulangan pada dinding abutment sudah memadai
d. Dimensi dan penulangan kolom pada pier sudah memadai
e. Penulangan utama bawah (longitudinal) pada footing Abutment tidak memadai
f. Penulangan utama bawah (longitudinal) pada Footing Pier sudah memadai namun mutu beton
Footing Pier perlu ditingkatkan
6. Revisi :
a. Merevisi mutu beton untuk PC-I Girder menjadi fc’ 50 MPa untuk bentang s/d 40m dan fc’
60MPa untuk bentang 45m
b. Melakukan review design untuk merevisi kedalaman tiang (bored pile) untuk mendapatkan
reaksi tiang yang tidak melampaui kapasita daya dukung ijin tiang. Usulan revisi panjang tiang
adalah berdasarkan pada kapasitas ijin pada kedalaman yang direkomendasi sehingga memadai
untuk mengantisipasi reaksi maksimum tiang (dapat dilihat pada table Pile Analysis Summary
terlampir). Konfigurasi kelompok tiang tidak perlu diubah.
c. Revisi mutu beton untuk footing/pilecap Pier dari 20 MPa menjadi 30 MPa sehingga penulangan
Footing Pier tidak perlu direvisi lagi.
d. Merevisi tulangan footing pada Abutment sebagai berikut:
• Abutment A1 : revisi diameter tulangan bawah longitudinal (F1/F3) dari D19 menjadi
D25
• Abutment A2 : revisi diameter tulangan bawah longitudinal (F1/F3) dari D19 menjadi
D25
JEMBATAN AKSES KALI PUTIH
PILE ANALYSIS SUMMARY
PILE DESIGN FROM PREVIOUS DED REVIEW RECOMMENDATION
Pile Pile Reaction Allowable Pile Reaction Allowable
Pile Length Pile Length
No. Sub Structure Bore Hole Diameter Condition Status Status
(m) Max KN Min KN Max KN Min KN (m) Max KN Min KN Max KN Min KN
(m)
1 Abutment A1 BM-80 1.5 15 Normal 4499 2784 5110 -2163 OK 14 4455 2784 5950 -3010 OK
Earthquake 5312 1494 7665 -3245 OK 5268 1494 8920 -4515 OK
2 Abutment A2 BM-81 1.5 15 Normal 4237 2813 3650 -1000 REVIEW 18 4370 2813 4500 -1560 OK
Earthquake 4872 1703 5475 -1500 OK 5005 1703 6750 -2340 OK
3 Pier P1 BM-80 1.5 10 Normal 5530 5003 4830 -1883 REVIEW 15 5751 5003 5770 -2827 OK
Earthquake 7194 2726 7245 -2825 OK 7415 2726 8655 -4240 OK
4 Pier P2 BM-81 1.5 10 Normal 5000 4405 4760 -1820 REVIEW 12 5088 4405 5140 -2197 OK
Earthquake 7164 1802 7140 -2730 REVIEW 7252 1802 7710 -3295 OK
CATATAN:
Review single pile capacity dilakukan dengan cara merencanakan ulang kedalaman tiang
yang digunakan pada setiap sub structure untuk mendapatkan kapasitas daya dukung
tiang yang memadai
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
BRIDGE DIMENSION
Carriageway Width
16.80 0.00 0.50
Sidewalk
Pavement thick = 50 mm t= 0 mm
1.90 1.300
BRIDGE CROSS SECTION IN SKEW DIRECTION
Bridge Width
17.80
Carriageway Width
16.80 0.00 0.50
Sidewalk
1.90 1.300
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
E. STEEL REINFORCEMENT
Steel Quality BJTD - 40
Yield Strength (fy) 390 MPa
Allowable Tension Stress 173.5 MPa
Allowable Compression Stress 112 MPa
Modulus Elasticity 200000 MPa
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
4. SECTION PROPERTIES
Geometric properties of the cross-section
SPAN 30M ACCESS AT END SPAN
Parameter Value
A Cross sectional area 14.75 m^2
Av,y Conventional shearing area along Y-axis 8.47 m^2
Av,z Conventional shearing area along Z-axis 3.51 m^2
α Angle between Y-Z and U-V axes -90 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 5.26 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 366.11 m^4
It Torsional moment of inertia (St. Venant) 1.5 m^4
Iw Warping constant 66.84 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.6 m
iz Radius of gyration about axis parallel to Z passing through centroid 4.98 m
W u+ Max elastic modulus about U-axis 41.14 m^3
W u- Min elastic modulus about U-axis 41.14 m^3
W v+ Max elastic modulus about V-axis 4.74 m^3
W v- Min elastic modulus about V-axis 6.51 m^3
W pl,u Plastic modulus about U-axis 63.53 m^3
W pl,v Plastic modulus about V-axis 7.77 m^3
Iu Moment of inertia about U-axis 366.11 m^4
Iv Moment of inertia about V-axis 5.26 m^4
iu Radius of gyration about U-axis 4.98 m
iv Radius of gyration about V-axis 0.6 m
au+ Centroid to edge of compression zone along +ve U-axis 0.32 m
au- Centroid to edge of compression zone along -ve U-axis 0.44 m
av+ Centroid to edge of compression zone along +ve V-axis 2.79 m
av- Centroid to edge of compression zone along -ve V-axis 2.79 m
yM Distance to centroid along Y-axis 0 m
zM Distance to centroid along Z-axis 0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -2.07 m
Zb Distance to shear centre along Z-axis 1.3 m
P Perimeter 68.7 m
Pi Internal perimeter 0 m
Pe External perimeter 68.7 m
I1 Moment of inertia about Y-axis 5.26 m^4
I2 Moment of inertia about Z-axis 366.11 m^4
I12 Product of inertia about the centroid -0 m^4
Ip Polar moment of inertia about centroid 371.37 m^4
ip Polar radius of gyration about centroid 5.02 m
Wp Polar elastic modulus about centroid 4.65 m
Parameter Value
A Cross sectional area 10 m^2
Av,y Conventional shearing area along Y-axis 3.45 m^2
Av,z Conventional shearing area along Z-axis 3.51 m^2
α Angle between Y-Z and U-V axes -90 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 4.5 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 251.57 m^4
It Torsional moment of inertia (St. Venant) 0.32 m^4
Iw Warping constant 99.19 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.67 m
iz Radius of gyration about axis parallel to Z passing through centroid 5.01 m
W u+ Max elastic modulus about U-axis 28.27 m^3
W u- Min elastic modulus about U-axis 28.27 m^3
W v+ Max elastic modulus about V-axis 3.72 m^3
W v- Min elastic modulus about V-axis 6.34 m^3
W pl,u Plastic modulus about U-axis 43.37 m^3
W pl,v Plastic modulus about V-axis 6.07 m^3
Iu Moment of inertia about U-axis 251.57 m^4
Iv Moment of inertia about V-axis 4.5 m^4
iu Radius of gyration about U-axis 5.01 m
iv Radius of gyration about V-axis 0.67 m
au+ Centroid to edge of compression zone along +ve U-axis 0.37 m
au- Centroid to edge of compression zone along -ve U-axis 0.63 m
av+ Centroid to edge of compression zone along +ve V-axis 2.83 m
av- Centroid to edge of compression zone along -ve V-axis 2.83 m
yM Distance to centroid along Y-axis 0 m
zM Distance to centroid along Z-axis -0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -1.02 m
Zb Distance to shear centre along Z-axis 1.12 m
P Perimeter 73.61 m
Pi Internal perimeter 0 m
Pe External perimeter 73.61 m
I1 Moment of inertia about Y-axis 4.5 m^4
I2 Moment of inertia about Z-axis 251.57 m^4
I12 Product of inertia about the centroid -0 m^4
Ip Polar moment of inertia about centroid 256.07 m^4
ip Polar radius of gyration about centroid 5.06 m
Wp Polar elastic modulus about centroid 3.21 m
Parameter Value
A Cross sectional area 17.27 m^2
Av,y Conventional shearing area along Y-axis 11.06 m^2
Av,z Conventional shearing area along Z-axis 3.49 m^2
α Angle between Y-Z and U-V axes -90 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 9 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 426.86 m^4
It Torsional moment of inertia (St. Venant) 1.89 m^4
Iw Warping constant 124.93 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.72 m
iz Radius of gyration about axis parallel to Z passing through centroid 4.97 m
W u+ Max elastic modulus about U-axis 47.96 m^3
W u- Min elastic modulus about U-axis 47.96 m^3
W v+ Max elastic modulus about V-axis 6.82 m^3
W v- Min elastic modulus about V-axis 8.99 m^3
W pl,u Plastic modulus about U-axis 74.22 m^3
W pl,v Plastic modulus about V-axis 10.97 m^3
Iu Moment of inertia about U-axis 426.86 m^4
Iv Moment of inertia about V-axis 9 m^4
iu Radius of gyration about U-axis 4.97 m
iv Radius of gyration about V-axis 0.72 m
au+ Centroid to edge of compression zone along +ve U-axis 0.39 m
au- Centroid to edge of compression zone along -ve U-axis 0.52 m
av+ Centroid to edge of compression zone along +ve V-axis 2.78 m
av- Centroid to edge of compression zone along -ve V-axis 2.78 m
yM Distance to centroid along Y-axis 0 m
zM Distance to centroid along Z-axis 0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -1.89 m
Zb Distance to shear centre along Z-axis 1.69 m
P Perimeter 75.9 m
Pi Internal perimeter 0 m
Pe External perimeter 75.9 m
I1 Moment of inertia about Y-axis 9 m^4
I2 Moment of inertia about Z-axis 426.86 m^4
I12 Product of inertia about the centroid -0 m^4
Ip Polar moment of inertia about centroid 435.86 m^4
ip Polar radius of gyration about centroid 5.02 m
Wp Polar elastic modulus about centroid 5.43 m
Parameter Value
A Cross sectional area 10.99 m^2
Av,y Conventional shearing area along Y-axis 4.43 m^2
Av,z Conventional shearing area along Z-axis 3.48 m^2
α Angle between Y-Z and U-V axes -90 deg
Iy Moment of inertia about axis parallel to Y passing through centroid 7.4 m^4
Iz Moment of inertia about axis parallel to Z passing through centroid 275.26 m^4
It Torsional moment of inertia (St. Venant) 0.35 m^4
Iw Warping constant 164.64 m^6
iy Radius of gyration about axis parallel to Y passing through centroid 0.82 m
iz Radius of gyration about axis parallel to Z passing through centroid 5 m
W u+ Max elastic modulus about U-axis 30.93 m^3
W u- Min elastic modulus about U-axis 30.93 m^3
W v+ Max elastic modulus about V-axis 5.12 m^3
W v- Min elastic modulus about V-axis 8.45 m^3
W pl,u Plastic modulus about U-axis 47.53 m^3
W pl,v Plastic modulus about V-axis 8.18 m^3
Iu Moment of inertia about U-axis 275.26 m^4
Iv Moment of inertia about V-axis 7.4 m^4
iu Radius of gyration about U-axis 5 m
iv Radius of gyration about V-axis 0.82 m
au+ Centroid to edge of compression zone along +ve U-axis 0.47 m
au- Centroid to edge of compression zone along -ve U-axis 0.77 m
av+ Centroid to edge of compression zone along +ve V-axis 2.81 m
av- Centroid to edge of compression zone along -ve V-axis 2.81 m
yM Distance to centroid along Y-axis -0 m
zM Distance to centroid along Z-axis 0 m
Sw Sectorial static moment 0 m^4
Yb Distance to shear centre along Y-axis -0.91 m
Zb Distance to shear centre along Z-axis 1.44 m
P Perimeter 80.52 m
Pi Internal perimeter 0 m
Pe External perimeter 80.52 m
I1 Moment of inertia about Y-axis 7.4 m^4
I2 Moment of inertia about Z-axis 275.26 m^4
I12 Product of inertia about the centroid -0 m^4
Ip Polar moment of inertia about centroid 282.65 m^4
ip Polar radius of gyration about centroid 5.07 m
Wp Polar elastic modulus about centroid 3.53 m
5. STRUCTURE MODEL
SAP2000 1-22-17 3:25:54
SAP2000 v14.0.0 - File:KBS ACCESS KPUTIH - Moment 3-3 Diagram (DEAD) - KN, m, C Units
SAP2000 1-22-17 3:24:01
SAP2000 v14.0.0 - File:KBS ACCESS KPUTIH - Shear Force 2-2 Diagram (DEAD) - KN, m, C Units
SAP2000 1-22-17 3:20:03
SAP2000 v14.0.0 - File:KBS ACCESS KPUTIH - Deformed Shape (DEAD) - KN, m, C Units
SAP2000 1-22-17 3:21:19
SAP2000 v14.0.0 - File:KBS ACCESS KPUTIH - Deformed Shape (EQX) - KN, m, C Units
SAP2000 1-22-17 3:22:01
SAP2000 v14.0.0 - File:KBS ACCESS KPUTIH - Deformed Shape (EQY) - KN, m, C Units
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
! "! #
! "
# $ ! %
& ' $ ! () * % % ! + (, + - &#. " /
# $ ! / 0 * () * % % ! + (, + - " /,
# $ ! * () * % % ! + (, + - " /
. *! * - &#. " /
. *! / * - " /
. *! * - 1 " /,
* *
. " &#. &#. " / 2 " 3 " /(,
" " /; 2 " / 2 " / ,
" 1 " /:,
* - " :/ 8$ 1 ! . !+
$ $ %&'
/(
/;
/,
/:
/
/ /, / /, / /, /
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
7. BRIDGE LOADINGS
Jembatan Akses Kali Putih
LOADING - SPAN = 40 m
A. DEAD LOAD
1. Girder Selfweight
a. At Mid Span = 176.82 kN/m
b. At End Span = 333.91 kN/m
70 mm
1260
3. Diaphragm
a. At Mid Span 5 x 112.808 = 564.04 kN
distributed load = 15.33 kN/m
B. SUPERIMPOSED LOAD
C. LIVE LOAD
1. D-Load
a. UDL (2.75x6x9)+(0.3x4.5) = 149.85 kN/m
b. KEL (with impact) 16.8 x 68.6 = 1152.48 kN 40.00
c. Brake 5% x D-Load = 8.90 kN/m
2. Truck Load
16 4 5 15
40
Jembatan Akses Kali Putih
LOADING - SPAN = 30 m
A. DEAD LOAD
1. Girder Selfweight
a. At Mid Span = 152.22 kN/m
b. At End Span = 270.91 kN/m
70 mm
1260
3. Diaphragm
a. At Mid Span 3 x 86.78 = 260.34 kN
distributed load = 9.71 kN/m
B. SUPERIMPOSED LOAD
C. LIVE LOAD
1. D-Load
a. UDL (2.75x6x9)+(0.3x4.5) = 149.85 kN/m
b. KEL (with impact) 16.8 x 68.6 = 1152.48 kN 30.00
c. Brake 5% x D-Load = 9.36 kN/m
2. Truck Load
11 4 5 10
30
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
8. PIER DESIGN
PIER COLUMN DESIGN
JEMBATAN ACCESS ROAD KALI PUTIH
PIER COLUMN FORCES
TABLE: Element Forces - Frames
Frame Station OutputCase CaseType StepType P V2 V3 T M2 M3
Text m Text Text Text KN KN KN KN-m KN-m KN-m
COL P1 LEFT 0 ULS:DL+SDL+LL Combination Max -14531 263 180 7 -1770 2649
COL P1 LEFT 11.5 ULS:DL+SDL+LL Combination Max -13356 263 180 7 -1695 1375
COL P1 LEFT 0 ULS:DL+SDL+LL Combination Min -22116 -128 -24 -3 -1971 -98
COL P1 LEFT 11.5 ULS:DL+SDL+LL Combination Min -20942 -128 -24 -3 -3843 -370
COL P1 LEFT 0 ULS:DL+SDL+LL+EQX Combination Max -18252 1325 656 21 1089 10360
COL P1 LEFT 11.5 ULS:DL+SDL+LL+EQX Combination Max -17078 1190 615 21 -5147 -3226
COL P1 LEFT 0 ULS:DL+SDL+LL+EQX Combination Min -22045 1130 554 16 988 8987
COL P1 LEFT 11.5 ULS:DL+SDL+LL+EQX Combination Min -20871 994 513 16 -6221 -4098
COL P1 LEFT 0 ULS:DL+SDL+LL+EQY Combination Max -18130 453 1767 8 7762 3996
COL P1 LEFT 11.5 ULS:DL+SDL+LL+EQY Combination Max -16955 413 1631 8 -10705 -110
COL P1 LEFT 0 ULS:DL+SDL+LL+EQY Combination Min -21922 258 1665 3 7661 2623
COL P1 LEFT 11.5 ULS:DL+SDL+LL+EQY Combination Min -20748 217 1529 3 -11779 -983
(Pmax)
60000
y
x
40000
2000 mm diam.
(Pmin)
-20000
(Pmax)
60000
y
x
40000
2000 mm diam.
(Pmin)
-20000
(Pmax)
60000
y
x
40000
2000 mm diam.
(Pmin)
-20000
A. Longitudinal Direction
1900
2000
100
b1
1250
fc' = 21 MPa
Allowable Stresses (Normal) : Allowable Stresses (E-quake) :
σcv-a = 8.30 Mpa (σch-a) σcv-a = 12.45
τcv-a = 0.36 Mpa (τch-a) τcv-a = 0.54
1900
2000
100
b1
4850
Width B = 17.70 m
PILECAP SECTION
1.00 a
b
0.50
1
2.00 2
O
P-3 P-2 P-1
0.00 0.00
2.50 1.25
3.75
PILE REACTION
Npile/row = 2 pile
Normal Equake
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 511.30 ton 673.10 ton
P-max2 = 511.30 ton 673.10 ton
o o
α= 0.00 0.00
P-1 = 1022.60 ton 1346.20 ton
Mo-1 = 2556.50 ton-m 3365.50 ton-m
8.44 15.23
Xo = 1.81 m
Self-W = 373.36 ton
Moment Mo = 674.12 ton-m
SOIL WEIGHT
A X Ax
4.69 9.38
Xo = 2.00 m
Soil-W = 149.34 ton
Moment Mo = 298.69 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
2.40 m
As
0.10 m
17.70 m
d= 2384 mm
b= 17700 mm
β= 0.85
φ= 0.8
a= 27.50 mm
φ= 0.7
Shear Vu = 1.00E+07 N
Vc = 3.86E+07 N
φVc = 2.70E+07 N > Vu --->No Stirrups required !!
Vs = -2.43E+07 N
Take S = 500 mm (transverse dir.)
Av-req = 0 mm2
Use Dia. = 13 mm
Number req. = 2 bars
Av = 265 mm2 > req --- OK !!
Distance = 3750.0 mm take : 500 mm (longitudinal dir)
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F5 / F7 F2
D32-125 D29-250
F7
D13-500
(Shear)
D32-125
D32-125 F1 / F3
F4 / F6
LONGITUDINAL DIRECTION
PILECAP BOTTOM REINFORCEMENT - TRANSVERSAL DIRECTION
fc' = 30 Mpa Conc Dens = 2.50 t/m3
fy = 390 Mpa Soil Dens = 1.80 t/m3
Width B = 9.50 m
PILECAP SECTION
1.00 a
b
0.50
1
2.00 2
O
P-3 P-2 P-1
0.00 0.00
1.25 4.85
5.95
PILE REACTION
Npile/row = 2 pile
Normal Transient
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 511.30 ton 677.70 ton
P-max2 = 511.30 ton 677.70 ton
o o
α= 0.00 0.00
P-1 = 1022.60 ton 1355.40 ton
Mo-1 = 1278.25 ton-m 1694.25 ton-m
13.39 39.83
Xo = 2.98 m
Self-W = 317.95 ton
Moment Mo = 945.91 ton-m
SOIL WEIGHT
A X Ax
6.33 19.19
Xo = 3.03 m
Soil-W = 108.16 ton
Moment Mo = 328.13 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
2.40 m
As
0.10 m
9.50 m
d= 2384 mm
b= 9500 mm
β= 0.85
φ= 0.8
a= 8.01 mm
Numb = 76 bars
As = 61123 mm2 > req --- OK !!
Bott 32 125 76 93
SHEAR REINFORCEMENT
φ= 0.7
Shear Vu = 1.14E+07 N
Vc = 2.07E+07 N
φVc = 1.45E+07 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F2 F5 / F7
D29-250 D32-125
F7
D13-500
(Shear)
D32-125
D32-125 F4 / F6
F1 / F3
TRANSVERSAL DIRECTION
PILECAP TOP REINFORCEMENT - LONGITUDINAL DIRECTION
Width B = 17.70 m
PILECAP SECTION
1.00 a
b
0.50
1
2.00 2
O
P-3 P-2 P-1
0.00 0.00
2.50 1.25
3.75
PILE REACTION
Npile/row = 2 pile
Normal Transient
Row 3 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-min1 = 500.30 ton 273.00 ton
P-min2 = 500.30 ton 273.00 ton
o o
α= 0.00 0.00
P-1 = 1000.60 ton 546.00 ton
Mo-1 = 2501.50 ton-m 1365.00 ton-m
8.44 15.23
Xo = 1.81 m
Self-W = 373.36 ton
Moment Mo = 674.12 ton-m
SOIL WEIGHT
A X Ax
4.69 9.38
Xo = 2.00 m
Soil-W = 149.34 ton
Moment Mo = 298.69 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As
2.40 m
17.70 m
d= 2385.5 mm
b= 17700 mm
β= 0.85
φ= 0.8
a= 0.00 mm
As req = 0 mm2
Use Dia. = 29 mm
Numb req = 2 bars
Dist. S = 17499.00 mm --> 250 mm
Numb = 71 bars
As = 46896.91 mm2 > req --- OK !!
Width B = 9.50 m
PILECAP SECTION
1.00 a
b
0.50
1
2.00 2
O
P-3 P-2 P-1
0.00 0.00
1.25 4.85
5.95
PILE REACTION
Npile/row = 2 pile
Normal Transient
Row 3 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-min1 = 0.00 ton 0.00 ton
P-min2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-min1 = 500.30 ton 272.60 ton
P-min2 = 500.30 ton 272.60 ton
o o
α= 0.00 0.00
P-1 = 1000.60 ton 545.20 ton
Mo-1 = 1250.75 ton-m 681.50 ton-m
13.39 39.83
Xo = 2.98 m
Self-W = 317.95 ton
Moment Mo = 945.91 ton-m
SOIL WEIGHT
A X Ax
6.33 19.19
Xo = 3.03 m
Soil-W = 108.16 ton
Moment Mo = 328.13 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As
2.40 m
9.50 m
d= 2355 mm
b= 9500 mm
β= 0.85
φ= 0.8
a= 17.15 mm
Numb = 76 bars
As = 61123 mm2 > req --- OK !!
Top 32 125 76 93
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
9. ABUTMENT DESIGN
ABUTMENT A1
ABUTMENT A2 DESIGN
1. FOUNDATION ANALYSIS
PILE ARRANGEMENT : 2 x 3
Ka = 0.2972
2.40 Kea = 0.4073
Eq-coef = 0.15
2.93 a
3
5.50 2.28 Pile Diameter = 1.50 m
1.30 Distance from Edge = 1.25 m
Pile Row = 2 pile
Pile per Row = 3 pile
Pile dist. (transv) = 7.55 m
1.00 Pilecap Width = 17.80 m
b
5.00
selfweight SW = 7603.3 kN
eccintricity moment MoSW = -725.8 kN-m
SUPERSTRUCTURE (REACTION)
SOIL WEIGHT
W-soil = 3150.2 kN
eccentricity moment Mo-soil = -2959.1 kN-m
EARTH PRESSURE
Ep1 = 1296.1 kN
Mo-Ep1 = 2376.2 kN-m
Earthquake Time :
Ep1 = 1776.6 kN
Mo-Ep1 = 3257.1 kN-m
1. NORMAL TIME
Load LF V HX MoX
kN kN kN-m
Bearing Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
468 884 1351 676 450
Pullout Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
468 0 468 234 156
(Pmax)
30000
20000
fs=0
10000 fs=0.5fy
2
1
3
Mx (k N -m)
(Pmin)
-10000
2. COEFFICIENT OF EARTH PRESSURE
1) Permanent Time
cos2 (φ - θ)
Ka = 2
cos2 θ cos (θ + δ) 1 + sin (φ + δ) sin (δ - α)
2) Transient Time
cos2 (φ - θ0 - θ )
Kea =
cos θ0 cos2 θ cos (θ + θ0 + δ) (1+ Xa) 2
where ;
δ : Angle of wall friction
For stability calculation = φ/2 = 15 degree
For sectional calculation = 0 degree
θ 0 = tan -1 kh = 8.531 degree
kh = 0.15
0.40 0.40
0.90
SELFWEIGHT
selfweight SW = 1651.84 kN
moment MoSW = -62.92 kN-m
SUPERSTRUCTURE (R)
Support : Moved
Exterior Girder : 2 Xo = 0.20 M
Interior Girder : 7 Yo = 2.28 M
EARTH PRESSURE
Normal Time :
Ep1 = 605.3 kN
Mo-Ep1 = 706.2 kN-M
Earthquake Time :
Ep1 = 849.6 kN
Mo-Ep1 = 991.2 kN-M
Surcharge = 10 kN/m2
Ep2 = 192.2 kN
Mo-Ep2 = 336.3 kN-M
A. NORMAL TIME
Load LF V HX MoX
kN kN kN-m
Load LF V HX MoZ
kN kN kN-m
Load LF V HZ MoX
kN kN kN-m
front
1.30 m
left right
rear
17.80 m
P ( kN)
(Pmax)
180000
140000
100000
fs=0
60000
fs=0.5fy
20000
1 2
SHEAR REINFORCEMENT
φ= 0.7
Shear Vu = 2.08E+06 N
Vc = 1.73E+07 N
φVc = 1.21E+07 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Vertical Horizontal Longt. Transv
REINFORCEMENT SKETCH
D19 - 125
D19 - 250
PILE CAPACITY OF BORED PILE
1900
2000
100
b1
1250
1900
2000
100
b1
1250
Width B = 17.80 m
PILECAP SECTION
1.00 a
1
2.00
O
Pc Pb Pa
0.00 0.00
1.55 1.25
2.80
PILE REACTION
Npile/row = 3 pile
Normal Equake
Row 3 :
Pc-max1 = 0.00 ton 0.00 ton
Pc-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
Pb-max1 = 0.00 ton 0.00 ton
Pb-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
Pb = 0.00 ton 0.00 ton
Mo-b = 0.00 ton-m 0.00 ton-m
Row 1 :
Pa-max1 = 361.20 ton 424.70 ton
Pa-max2 = 361.20 ton 424.70 ton
o o
α= 0.00 0.00
Pa = 1083.60 ton 1274.10 ton
Mo-a = 1679.58 ton-m 1974.86 ton-m
5.60 7.84
Xo = 1.40 m
Self-W = 249.20 ton
Moment Mo = 348.88 ton-m
SOIL WEIGHT
A X Ax
2.80 3.92
Xo = 1.40 m
Soil-W = 89.71 ton
Moment Mo = 125.60 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
1.90 m
As
0.10 m
17.80 m
d= 1862.5 mm
b= 17800 mm
β= 0.85
φ= 0.8
a= 44.68 mm
SHRINKAGE REINFORCEMENT
Numb = 4 bars/m
As = 804 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 1.57E+07 N
Vc = 2.48E+07 N
φVc = 1.73E+07 N > Vu --->No Stirrups required !!
Vs = -1.61E+06 N
Take S = 500 mm (transverse dir.)
Av-req = 0 mm2
Use Dia. = 13 mm
Number req. = 2 bars
Av = 265 mm2 > req --- OK !!
Distance = 2800.00 mm take : 500 mm (longitudinal dir)
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F6 F2 / F4
D16-250 D19-125
F9 / F9-1
D13-500/500
(Shear)
D25-125
D16-250 F1 / F3
F5
LONGITUDINAL DIRECTION
PILECAP TOP REINFORCEMENT
Width B = 17.80 m
PILECAP SECTION
1.00 a
1
2.00
O
Pf Pe Pd
0.00 0.00
1.15 1.25
2.40
PILE REACTION
Npile/row = 3 pile
Normal Transient
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 281.30 ton 170.30 ton
P-max2 = 281.30 ton 170.30 ton
o o
α= 0.00 0.00
P-1 = 843.90 ton 510.90 ton
Mo-1 = 970.49 ton-m 587.54 ton-m
4.80 5.76
Xo = 1.20 m
Self-W = 213.60 ton
Moment Mo = 256.32 ton-m
SOIL WEIGHT
A X Ax
2.40 2.88
Xo = 1.20 m
Soil-W = 76.90 ton
Moment Mo = 92.28 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As 1.90 m
17.80 m
d= 1865.5 mm
b= 17800 mm
β= 0.85
φ= 0.8
a= 19.72 mm
SHRINKAGE REINFORCEMENT
Numb = 4 bars/m
As = 804 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 9.75E+06 N
Vc = 2.48E+07 N
φVc = 1.74E+07 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F2 / F4 F6
D19-125 D16-250
F9 / F9-1
D13-500/500
(Shear)
D16-250
D25-125 F5
F1 / F3
TRANSVERSAL DIRECTION
ABUTMENT A2
ABUTMENT A2 DESIGN
1. FOUNDATION ANALYSIS
PILE ARRANGEMENT : 2 x 3
Ka = 0.2972
2.40 Kea = 0.4073
Eq-coef = 0.15
2.93 a
3
5.50 2.28 Pile Diameter = 1.50 m
1.30 Distance from Edge = 1.25 m
Pile Row = 2 pile
Pile per Row = 3 pile
Pile dist. (transv) = 7.55 m
1.00 Pilecap Width = 17.80 m
b
5.00
selfweight SW = 7603.3 kN
eccintricity moment MoSW = -725.8 kN-m
SUPERSTRUCTURE (REACTION)
SOIL WEIGHT
W-soil = 3150.2 kN
eccentricity moment Mo-soil = -2959.1 kN-m
EARTH PRESSURE
Ep1 = 1296.1 kN
Mo-Ep1 = 2376.2 kN-m
Earthquake Time :
Ep1 = 1776.6 kN
Mo-Ep1 = 3257.1 kN-m
1. NORMAL TIME
Load LF V HX MoX
kN kN kN-m
Bearing Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
468 884 1351 676 450
Pullout Capacity
Ps Pe Pu Pallowable (ton)
(ton) (ton) (ton) FS = 2 FS = 3
468 0 468 234 156
(Pmax)
30000
20000
fs=0
10000 fs=0.5fy
2
1
3
Mx (k N -m)
(Pmin)
-10000
2. COEFFICIENT OF EARTH PRESSURE
1) Permanent Time
cos2 (φ - θ)
Ka = 2
cos2 θ cos (θ + δ) 1 + sin (φ + δ) sin (δ - α)
2) Transient Time
cos2 (φ - θ0 - θ )
Kea =
cos θ0 cos2 θ cos (θ + θ0 + δ) (1+ Xa) 2
where ;
δ : Angle of wall friction
For stability calculation = φ/2 = 15 degree
For sectional calculation = 0 degree
θ 0 = tan -1 kh = 8.531 degree
kh = 0.15
0.40 0.40
0.90
SELFWEIGHT
selfweight SW = 1651.84 kN
moment MoSW = -62.92 kN-m
SUPERSTRUCTURE (R)
Support : Moved
Exterior Girder : 2 Xo = 0.20 M
Interior Girder : 7 Yo = 2.28 M
EARTH PRESSURE
Normal Time :
Ep1 = 605.3 kN
Mo-Ep1 = 706.2 kN-M
Earthquake Time :
Ep1 = 849.6 kN
Mo-Ep1 = 991.2 kN-M
Surcharge = 10 kN/m2
Ep2 = 192.2 kN
Mo-Ep2 = 336.3 kN-M
A. NORMAL TIME
Load LF V HX MoX
kN kN kN-m
Load LF V HX MoZ
kN kN kN-m
Load LF V HZ MoX
kN kN kN-m
front
1.30 m
left right
rear
17.80 m
P ( kN)
(Pmax)
180000
140000
100000
fs=0
60000
fs=0.5fy
20000
1 2
SHEAR REINFORCEMENT
φ= 0.7
Shear Vu = 2.08E+06 N
Vc = 1.73E+07 N
φVc = 1.21E+07 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Vertical Horizontal Longt. Transv
REINFORCEMENT SKETCH
D19 - 125
D19 - 250
PILE CAPACITY OF BORED PILE
1900
2000
100
b1
1250
1900
2000
100
b1
1250
Width B = 17.80 m
PILECAP SECTION
1.00 a
1
2.00
O
Pc Pb Pa
0.00 0.00
1.55 1.25
2.80
PILE REACTION
Npile/row = 3 pile
Normal Equake
Row 3 :
Pc-max1 = 0.00 ton 0.00 ton
Pc-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
Pb-max1 = 0.00 ton 0.00 ton
Pb-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
Pb = 0.00 ton 0.00 ton
Mo-b = 0.00 ton-m 0.00 ton-m
Row 1 :
Pa-max1 = 361.20 ton 424.70 ton
Pa-max2 = 361.20 ton 424.70 ton
o o
α= 0.00 0.00
Pa = 1083.60 ton 1274.10 ton
Mo-a = 1679.58 ton-m 1974.86 ton-m
5.60 7.84
Xo = 1.40 m
Self-W = 249.20 ton
Moment Mo = 348.88 ton-m
SOIL WEIGHT
A X Ax
2.80 3.92
Xo = 1.40 m
Soil-W = 89.71 ton
Moment Mo = 125.60 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
1.90 m
As
0.10 m
17.80 m
d= 1862.5 mm
b= 17800 mm
β= 0.85
φ= 0.8
a= 44.68 mm
SHRINKAGE REINFORCEMENT
Numb = 4 bars/m
As = 804 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 1.57E+07 N
Vc = 2.48E+07 N
φVc = 1.73E+07 N > Vu --->No Stirrups required !!
Vs = -1.61E+06 N
Take S = 500 mm (transverse dir.)
Av-req = 0 mm2
Use Dia. = 13 mm
Number req. = 2 bars
Av = 265 mm2 > req --- OK !!
Distance = 2800.00 mm take : 500 mm (longitudinal dir)
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F6 F2 / F4
D16-250 D19-125
F9 / F9-1
D13-500/500
(Shear)
D25-125
D16-250 F1 / F3
F5
LONGITUDINAL DIRECTION
PILECAP TOP REINFORCEMENT
Width B = 17.80 m
PILECAP SECTION
1.00 a
1
2.00
O
Pf Pe Pd
0.00 0.00
1.15 1.25
2.40
PILE REACTION
Npile/row = 3 pile
Normal Transient
Row 3 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-3 = 0.00 ton 0.00 ton
Mo-3 = 0.00 ton-m 0.00 ton-m
Row 2 :
P-max1 = 0.00 ton 0.00 ton
P-max2 = 0.00 ton 0.00 ton
o o
α= 0.00 0.00
P-2 = 0.00 ton 0.00 ton
Mo-2 = 0.00 ton-m 0.00 ton-m
Row 1 :
P-max1 = 281.30 ton 170.30 ton
P-max2 = 281.30 ton 170.30 ton
o o
α= 0.00 0.00
P-1 = 843.90 ton 510.90 ton
Mo-1 = 970.49 ton-m 587.54 ton-m
4.80 5.76
Xo = 1.20 m
Self-W = 213.60 ton
Moment Mo = 256.32 ton-m
SOIL WEIGHT
A X Ax
2.40 2.88
Xo = 1.20 m
Soil-W = 76.90 ton
Moment Mo = 92.28 ton-m
SUMMARY OF FORCES
V Mo
No. Load LF
ton tm
0.10 m
As 1.90 m
17.80 m
d= 1865.5 mm
b= 17800 mm
β= 0.85
φ= 0.8
a= 19.72 mm
SHRINKAGE REINFORCEMENT
Numb = 4 bars/m
As = 804 mm2/m > As-req ---> OK !!
φ= 0.7
Shear Vu = 9.75E+06 N
Vc = 2.48E+07 N
φVc = 1.74E+07 N > Vu --->No Stirrups required !!
STIRRUPS
Position Diameter Number bars Distance mm
mm Perpnd. Paralel Longt. Transv
SKETCH OF REINFORCEMENT
F2 / F4 F6
D19-125 D16-250
F9 / F9-1
D13-500/500
(Shear)
D16-250
D25-125 F5
F1 / F3
TRANSVERSAL DIRECTION
STRUCTURAL DESIGN REVIEW REPORT
JEMBATAN ACCESS ROAD KALI PUTIH
1 Abutment A1 BM-80 1.5 15 Normal 4499 2784 5110 -2163 OK 14 4455 2784 5950 -3010 OK
Earthquake 5312 1494 7665 -3245 OK 5268 1494 8920 -4515 OK
2 Abutment A2 BM-81 1.5 15 Normal 4237 2813 3650 -1000 REVIEW 18 4370 2813 4500 -1560 OK
Earthquake 4872 1703 5475 -1500 OK 5005 1703 6750 -2340 OK
3 Pier P1 BM-80 1.5 10 Normal 5530 5003 4830 -1883 REVIEW 15 5751 5003 5770 -2827 OK
Earthquake 7194 2726 7245 -2825 OK 7415 2726 8655 -4240 OK
4 Pier P2 BM-81 1.5 10 Normal 5000 4405 4760 -1820 REVIEW 12 5088 4405 5140 -2197 OK
Earthquake 7164 1802 7140 -2730 REVIEW 7252 1802 7710 -3295 OK
CATATAN:
Review single pile capacity dilakukan dengan cara merencanakan ulang kedalaman tiang
yang digunakan pada setiap sub structure untuk mendapatkan kapasitas daya dukung
tiang yang memadai
PILE GROUP ANALYSIS
1. JEMBATAN AKSES ROAD KALI PUTIH ( A1 )
Springs ( BM-80 )
1.25
A
B1
1 C1
2.00 2 6.5
2
D E1 F1
1.25
17.8
NOTE
CASE A = SLS:DL+SDL+LL
CASE B = SLS:DL+SDL+LL+EQX
CASE C = SLS:DL+SDL+LL+EQY
1
BOTTOM BORE PILE
1.25
A B2 1 C2
2.00 2 6.5
2
D E2 F2
1.25
17.8
NOTE
CASE A = SLS:DL+SDL+LL + Dead Load Bored Pile
CASE B = SLS:DL+SDL+LL+EQX + Dead Load Bored Pile
CASE C = SLS:DL+SDL+LL+EQY + Dead Load Bored Pile
ABUTMENT A1
TOP Vertical
1. Max = 4687.06 kN
1. Min = 1494.28 kN
L= 15 m Moment
M2 = 1363.02 kN.m
M3 = 2563.11 kN.m
Vertical
BOTTOM 2. Max = 5311.65 kN
2. Min = 2118.87 kN
2
4. JEMBATAN AKSES ROAD KALI PUTIH ( A2 )
Springs ( BM-81 )
1.25
A
B1
1 C1
2.00 2 6.5
2
D E1 F1
1.25
17.8
NOTE
CASE A = SLS:DL+SDL+LL
CASE B = SLS:DL+SDL+LL+EQX
CASE C = SLS:DL+SDL+LL+EQY
1
BOTTOM BORE PILE
1.25
A B2 1 C2
2.00 2 6.5
2
D E2 F2
1.25
17.8
NOTE
CASE A = SLS:DL+SDL+LL + Dead Load Bored Pile
CASE B = SLS:DL+SDL+LL+EQX + Dead Load Bored Pile
CASE C = SLS:DL+SDL+LL+EQY + Dead Load Bored Pile
ABUTMENT A2
TOP Vertical
1. Max = 4247.11 kN
1. Min = 1703.22 kN
L= 15 m Moment
M2 = 1180.83 kN.m
M3 = 2047.73 kN.m
Vertical
BOTTOM 2. Max = 4871.71 kN
2. Min = 2327.81 kN
2
2. JEMBATAN AKSES ROAD KALI PUTIH ( P1 )
Springs ( BM-80 )
1.25
A B1 1 C1
3.50 D1 E1
2 9.5
3.5
F G1 H1
1.25
17.7
NOTE
CASE A = SLS:DL+SDL+LL
CASE B = SLS:DL+SDL+LL+EQX
CASE C = SLS:DL+SDL+LL+EQY
1
BOTTOM BORE PILE
1.25
A 1B2 C2
3.50 D E2 2 9.5
3.5
F G2 H2
1.25
17.7
NOTE
CASE A = SLS:DL+SDL+LL + Dead Load Bored Pile
CASE B = SLS:DL+SDL+LL+EQX + Dead Load Bored Pile
CASE C = SLS:DL+SDL+LL+EQY + Dead Load Bored Pile
ABUTMENT P1
TOP Vertical
1. Max = 6777.34 kN
1. Min = 2725.91 kN
L= 10 m Moment
M2 = 1055.38 kN.m
M3 = 728.53 kN.m
Vertical
BOTTOM 2. Max = 7193.73 kN
2. Min = 3142.31 kN
2
3. JEMBATAN AKSES ROAD KALI PUTIH ( P2 )
Springs ( BM-81 )
1.25
A B1 1 C1
3.50 D1 E1
2 9.5
3.5
F G1 H1
1.25
17.7
NOTE
CASE A = SLS:DL+SDL+LL
CASE B = SLS:DL+SDL+LL+EQX
CASE C = SLS:DL+SDL+LL+EQY
1
BOTTOM BORE PILE
1.25
A 1B2 C2
3.50 D E2 2 9.5
3.5
F G2 H2
1.25
17.7
NOTE
CASE A = SLS:DL+SDL+LL + Dead Load Bored Pile
CASE B = SLS:DL+SDL+LL+EQX + Dead Load Bored Pile
CASE C = SLS:DL+SDL+LL+EQY + Dead Load Bored Pile
ABUTMENT P2
TOP Vertical
1. Max = 6748.09 kN
1. Min = 1802.5 kN
L= 10 m Moment
M2 = 958.035 kN.m
M3 = 324.86 kN.m
Vertical
BOTTOM 2. Max = 7164.48 kN
2. Min = 2218.89 kN
2
SINGLE PILE CAPACITY
PILE CAPACITY OF BORED PILE
(Pmax)
30000
y
x
20000
(Pmin)
-10000
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-4\PAKET 4-4\4.9. JEMBATA
Project: JEMBATAN AKSES KPUTIH
Column: A1_BP1500 Engineer:
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 29 MPa fy = 390 MPa
Ec = 25310.3 MPa Es = 199955 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.839702
Section:
========
Circular: Diameter = 1500 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Tied; #10 ties with #32 bars, #13 with larger bars.
phi(a) = 0.8, phi(b) = 0.9, phi(c) = 0.65
Layout: Circular
Pattern: All Sides Equal (Cover to transverse reinforcement)
Total steel area, As = 20640 mm^2 at 1.17%
32 #29 Cover = 70 mm
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 7224.0 170.0 7149.6 42.056
2 8494.0 4095.0 7272.5 1.776
3 6190.0 2362.0 6831.4 2.892
(Pmax)
30000
y
x
20000
(Pmin)
-10000
========================================================================
Computer program for the Strength Design of Reinforced Concrete Sections
========================================================================
General Information:
====================
File Name: C:\Users\dwise\Documents\DSDOCS\CALCULATION\JEMBATAN\SEKSI-4\PAKET 4-4\4.9. JEMBATA
Project: JEMBATAN AKSES KPUTIH
Column: P1_BP1500 Engineer:
Code: ACI 318-02 Units: Metric
Material Properties:
====================
f'c = 29 MPa fy = 390 MPa
Ec = 25310.3 MPa Es = 199955 MPa
Ultimate strain = 0.003 mm/mm
Beta1 = 0.839702
Section:
========
Circular: Diameter = 1500 mm
Reinforcement:
==============
Rebar Database: ASTM A615M
Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2) Size Diam (mm) Area (mm^2)
---- --------- ----------- ---- --------- ----------- ---- --------- -----------
# 10 10 71 # 13 13 129 # 16 16 199
# 19 19 284 # 22 22 387 # 25 25 510
# 29 29 645 # 32 32 819 # 36 36 1006
# 43 43 1452 # 57 57 2581
Confinement: Tied; #10 ties with #32 bars, #13 with larger bars.
phi(a) = 0.8, phi(b) = 0.9, phi(c) = 0.65
Layout: Circular
Pattern: All Sides Equal (Cover to transverse reinforcement)
Total steel area, As = 20640 mm^2 at 1.17%
32 #29 Cover = 70 mm
Factored Loads and Moments with Corresponding Capacities: (see user's manual for notation)
=========================================================
Pu Mux fMnx
No. kN kN-m kN-m fMn/Mu
--- ------------ ------------ ------------ --------
1 10029.0 1736.0 7118.4 4.100
2 13203.0 3236.0 6452.3 1.994
3 5355.0 3236.0 6562.1 2.028
4 13293.0 3021.0 6424.3 2.127
5 5347.0 3021.0 6559.3 2.171
6 9813.0 1736.0 7145.9 4.116